sr 2000 used for sale

Offer 24178 Specifications: - Center height 250 mm - Center width 2000 mm - larger circulation – Ø over bed 490 mm - via flat sleds approx. 300 mm - Spindle bore 72 mm - Pick-up cone of the tailstock quill MK 5 - Travel of the tailstock quill 260 mm - Spindle speeds 25 - 1160 rpm -Feeds - Travel of the cross slide 200 mm - Travel of the upper slide 115 mm - Drive 380 V / 5.5 kW - with: - Tailstock, 3-jaw lining, bezel - Steel holder, moving center punch, - Chip tray - Space requirement approx. W 3500 x H 1500 x D 1300 mm - Weight approx. 3000 kg

Key data: 65 mm, 510 mm

12-8 position driven turrets - Y axis +/- 40 mm - with Lns Quick Load short barfeed - well tooled - fanuc 18i-TA Control

Key data: 20000 kN, 135 mm

Dosing 1: Plasticizing 1: Screw diameter mm 135 Screw diameter mm 120 | 135 | 150 Dosing Stroke Screw stroke mm 610 Maximum injection capacity cm3 6899 | 8731 | 10780 Screw speed min-1 125 Worm torque Screw torque Nm 14000 Maximum screw speed reduced torque min-1 135 Reduced torque maximum screw speed Nm 12963 Reduced screw speed maximum screw torque min-1 112 Maximum screw torque reduced screw speed Nm 15630 Plasticizing performance (3-zone) 1.2 Recovery rate (3-zone screw) 1.2 g/s 165 | 222.9 | 231,3 Plasticizing performance (barrier) 3 Recovery rate (barrier screw) 3 g/s 208.3 | 279.2 | 264,6 1) Values for polystyrene up to injection unit 2550 according to ETR 10100 1) Data for GPPS up to injection unit 2550 acc. ETR 10100 2) Values for HDPE from injection unit 3550 according to ETR 10100 2) Data for HDPE from injection unit 3550 onward acc. ETR 10100 3) Values for HDP ...

carrying capacity: 500 kg weight: 930 kg dimensions: 1250 x 2590 x 1500 mm Operating instructions available technical data see attached PDF The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Roller Chassis - Carrier Chassis YALE Payload 2,000 kg Flange width 66 to 220 mm Flange thickness max. 25 mm Smallest curve radius 1.15 m Hand force at nominal load 7 kg Weight approx. 16 kg 16 units in stock - unit price

workpiece length: 2000 mm max. workpiece diameter: 400 mm min. workpiece diameter: mm bore spindle turning speed range: 260-1850 U/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

rated capacity: 2000 KG ram hammer stroke: 1080 mm throat: 1100 mm impact capacity: 10000 kgm no. of strokes: 125 Hub/min ram hammer weight: 2300 kg work height max.: 620 mm total power requirement: . kW weight of the machine ca.: t dimensions of the machine ca.: m Steam drive The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding length: 2100 mm grinding width: 600 mm workpiece height: . mm magnetic plate size: 2000x600 mm total power requirement: 55 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 800 mm turning length: 2000 mm control: Monfort R&D turning diameter over slide: 520 mm spindle hollow: 88 mm total power requirement: 53 kW weight of the machine ca.: t dimensions of the machine ca.: 4,2x2,2x1,9 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 2000 mm plate depth: 3000 mm plate height: 350 mm total power requirement: kW weight of the machine ca.: t required space: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dematic conveyor accumulating roller conveyors 2625-500-440 RA1995 Accumulating roller conveyor Nominal/outer width (NB): 500 mm Available conveyor lengths (FL): 2625 mm, expandable with further pieces Further information Manufacturer: Siemens Dematic Type: Accumulation roller conveyor Accumulation size: 750 mm Year of manufacture: unknown Condition: good (used) roller width (RB): 440 mm roller pitch: 125 mm variable drive type: SEW gear motor weight of conveyed material: up to 30 kg Accumulating mechanics: Light barriers with pneumatic valve and cylinder The following accessories are optionally available e.g.: Frequency converter supports side guides Price: on request plus VAT ex central warehouse Dr. Sonntag GmbH & Co. KG 97076 Würzburg Features: Electric data: 380-400 condition: very good (used) Conveying length in mm: 2625 Nominal / outside width in mm: 500 Roll width in mm: 440 Ro ...

2005 STRIKO WESTOFEN MH I-2 3000/2000 Charging system Oven Technical data: See pictures Find more here - / Contact us at -

Bridge type Machining Centre NICOLAS CORREA EURO 2000 - 18.000 rpm - capacity 2000x1250x650 mm, CNC SELCA 4045, Information about technical data are not binding., Machine available subject to prior sale., Working table size: 2000x1000 mm, Longitudinal travel x axis: 2000 mm, Cross travel y axis: 1250 mm, Vertical travel z axis: 650 mm, Measurement system: HEIDENHAIN optical scales, Working feed x-y-z axes: 0 - 30.000 mm/1, Rapid feed x-y-z axes: 30.000 mm/1, Spindle taper type: HSK 63, Automatic tools change nr.: 40, Spindle speed: 0- 18.000 rpm, Spindle motor power: 20 Kw, Cnc: SELCA 4045, Approx net weight: 20.000 Kg, Accessories: through-spindle coolant, chip conveyor

CNC controller: Mitsubishi M-720BM (MAPPS 2) Capacity X-axis travel mm: 260 Z-axis travel mm: 590 Turning length mm: 510 Max. turning diameter mm: ø: Ø356 Upper turret Tool holder: 12 Main spindle Speed spindle rpm: 5000 Drive power spindle kW: 15/11 Spindle bore mm: 73 Manufacturer: KITAGAWA Equipment Chip conveyor Signal lamp Tool measuring arm High pressure pump Workarea light 4th axis Interface for Bar feeder Rated power kVA Working time hours Under power: 7456 Spnidle: 5423 Basic machine dimensions / weight Length mm: 3495 Width mm: 2050 Height mm: 2230 Weight kg: 5800

Granit marble ATELIERS MAITRE Length: 2000 mm Width: 1200 mm Thickness: 400 mm Height on feet: 910 mm Class 2 Weight: approx 2 T

1999 WEBER LC 2000 DDP-600 Working width max. 600 mm Workpiece thickness max. 150 mm automatic measurement of the workpiece thickness Feed continuously adjustable 2 - 12 m/min. Aggregate equipment: 1) Contact roller unit with smooth steel roller Drive motor 15 KW, pole-changing for 2 grinding speeds 2) Rubber contact roller assembly with corrugated rubber roller Hardness 60 Shore drive motor 15 KW, pole-changing, this one The motor also drives the subsequent sanding shoe unit 3) Sanding shoe unit pneumatically controlled Machine complete with small parts return, designed as a transport curve, as a plate conveyor transport Machine weight approx. 1,800 kg Connection values: 400 V, 50 Hz, 3 Ph. Find more here - / Contact us at -

Specifications: Maximum cutting width: 2050 mm Maximum cutting capacity steel: 0.5 - 4.0 mm Adjustable rip fence: 1050 mm Retraction function Cutting gap adjustment Working height: 1030 mm Dimensions (length x width x height): approx. 2500 x 1900 x 1750 mm Weight: approx. 3,6 tons

Good day We offer you a used OCC sorting system consisting of a paper spike, type 2000, from the manufacturer Grumbach und Petermann GmbH, with a paper take-off belt, Bollegraaf type HBGT 1200 x 4760 15° and a single-deck star screen, fine, manufacturer Lubo Screening & Recycling Systems B.V. The machines were dismantled down to the base frame, derusted, primed and finally painted. Defective shafts and rubber stars, the V-belts and spikes of the PaperSpike as well as pneumatic cylinders were replaced. All bearings and drive chains were replaced, and the engines and transmissions were checked. A viewing is possible by appointment. We assume no liability for the technical information or any errors. We would be happy if this machine is interesting for you. Your service team Mertens & Frowein GmbH

Sling chains 4 - strand J.D.T. Load capacity 60 tons 4 - Strand with rocker Effective length 2,000 mm Nominal chain thickness 32 mm Coupling links with shackle 35to Crack testing according to BGR 500 in 2012 new Test number 29186 Weight approx. 318 kg Chain audit in 2012 - as good as new - unused -

Ultrasonic Banderolier ATS US 2000 AST-MDM; cleaned and tested; Frame size 900x750mm; Belt width 30mm; suitable for paper (also suitable for TruePaper paper) or foil; Meter reading 795,000 thousand; Compressed air required. Ultrasonic banding machine ATS US 2000 AST-MDM; cleaned and checked;  frame size 900x750mm; band width 30mm; used for paper (also for TruePaper material) or foil; counter 795,000; pressurized air needed.

Specifications: Clamping plate dimensions: 2050 x 1000 mm Panel thickness: 170 mm T-slots: 15 / 25 mm Dimensions (length x width x height): approx. 2050 x 1000 x 170 mm The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.

turning diameter: max. 480 mm turning length: max. 2.000 mm control: Sinumerik 840 D Siemens swing diameter max. over bed cover: 520 mm Main spindle:: turning speed range - main spindle: 7 - 2.800 min/-1 transmission ratio: 2 power capacity - main spindel: 53 kW max. Torque: 3.456 Nm spindle nose: 11 DIN 55026 chuck diameter: 315 mm spindle bore: 103 mm usable bar diameter: 82 mm axis stroke:: x-travel: 405 mm z-travel: 2.049 mm Tailstock:: diameter of quill: 100 mm quill stroke: 100 mm tension force: 14 kN capture: 30 DIN 2079 feeds:: rapid traverse: 10 m/min Working speed: 0,1 - 10.000 mm/min feed power: 15 kN Tool Mount:: number of toolpositions: 12 pos. driven statition: 6 pos. Shank diameter: 50 mm power capacity: 5,4 kW Max. Speed: 2.500 / 625 min/-1 max. Torque: 25 / 100 Nm total power requirement: ca. 50 kW weight of the machine ca.: 14 t dimensions of the machine ca.: 6,4 x ...

(printing, laminating, punching) Equipment / Additional information: Car inspection stickers were last produced

x-travel: 1700 mm y-travel: 800 mm z-travel: 890 mm table surface area: 2000 x 630 mm spindle taper: SK 50 spindle turning speed range: 35 - 3000 U/min spindle drive: 26 kW feeds longditudinal/cross/vertical: 6 - 5000 mm/min rapid traverse: 15 m/min table load: max. 6000 kg control: HEIDENHAIN control: TNC 360 total power requirement: 45 kVA weight of the machine ca.: 13 t dimensions of machine L x W x H: 5,2 x 2,78 x 2,95 m Accessories: vertical head swivelling in 2 planes with hydr. tool clamping, various tool fixtures, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1800 KW, 2250 kVA, 415 V

Diesel Generator 5 x CAT 3516B 2000 kVA / 50 Hz – 2023 Never Installed Never installed, surplus CAT 3516B skid mounted diesel generating sets. Engine is coupled with 2000 kVA / 415 V / 50 Hz Leroy Sommer DSG 74L1 brushless synchronous alternator with a flexible coupling, and both mounted on a rigid base frame. These units are designed for standby and prime duty. Main engine control panel EMCP, 24V electric starting system. Technical data Engine type CAT 3516B – 16-cylinder, 1500 rpm diesel engine Alternator Leroy Sommer 2000 kVA / 415V / 50Hz Power factor 0.8 Manufacturing year 2023 Operating hours Zero, never installed Number of units available 5 pcs Prime rating 2000 kVA (1600 kW) Stand by rating 2240 kVA (1800 kW) Control system EMCP 4.2

Key data: 2000 kN, 240 g/PS, 45 mm

Arburg 520 C - Allrounder 2000-675 -Injection molding machine - Control: Selogica - Handlebar spacing: 520 x 520 mm - Handlebar extension: 100 mm - Tool installation height: 350 mm - Opening travel: 650 mm - Centering: 125 mm - Core pull: 2 - Screw diameter: 45 mm - Shot weight - HP : 240g - Clamping force: 2000 KN - Operating hours pump: 61908 - Automatic operating hours: 55566 - Working position: Standard

Specifications: - Max. working width 2020 mm - max. material thickness at 40 kg / mm² strength 2 mm - Bending angle adjustment pre-selectable 0 - 135 ° - Upper bolster clamping via eccentric lever + foot pedal - Largest opening width / stroke of the upper beam 100 mm - Height adjustability of the lower beam 25 mm - Space requirement approx. W 2950 x H 1200 x D 800 mm - Weight approx. 1450 kg

Manual turning head Hydraulic clamping Longitudinal travel X-axe: 2000 mm Cross travel Y-axe: 1000 mm Travel Z-axe: 800 mm Dimensions clamping space- table: 2200 x 800 mm Power on spindle: 18,5 kWt Admission in millinghead (ISO): ISO 50 Max speedrange: 1500 rpm Control: Heidenhain Weight: 14000 kg

Manufacturer: Frenostat Bremsgerät Typ 2000 Hilger und Kern, Type: 400/60/3132000, Model: 137700,

1 gebr. Boiler --------------------------- Make : LOOS; Gunzenhausen Type : U-HD Heating surface approx. : 31 m² Power max. : 2.000 kg/h most permissible. Operating overpressure : 10 bar Increased test pressure : 18 bar Water content at NW approx. : 1.740 l Water content full approx. : 2.480 l Year of construction : 1999 equipped with Weishaupt gas burner, gas control system, Control cabinet, feed water pump, water level sight glass, steam and safety valve and the existing coarse and fine fittings

1 gebr. Boiler ---------------------------------- - mounted on frames - Manufacturer : Jumey Heating surface approx. Taxi: 40 m² Capacity : 2,000 kg/h Operating overpressure max. : 10.0 bar Previously operated with : 5.0 bar Water capacity at NW approx. : 3,540 l Water content full approx. : 4.750 l Year of construction : 1994 equipped with Weishaupt gas burner, gas control system, Control cabinet, feed water pump, and the existing coarse and fine fittings.

Manufacturer: Frenostat 2000 , Model: 32320000, Serial number: 90042,

Manufacturer: Frenostat 2000, Type: Bremsgeraät, Model: 32320000, Serial number: 165944,

Manufacturer: Frenostat 2000 , Model: 3232000, Serial number: 111443,

Manufacturer: Kuka KR 180-2 2000, Year: 2004, Max workpiece weights kg: 180, Year :2004

Manufacturer: Kuka KR 150-2 2000, Year: 2007, Max workpiece weights kg: 150, Year :2007

Manufacturer: Kuka KR 150-2 2000, Year: 2007, Max workpiece weights kg: 150, Year :2007

Manufacturer: Cefla, Type: TR 2000, Year: 2015, incl.control: yes, Length-width mm: 20000x1300, Programming possible: yes, Length mm: 2000, Working widht mm: 1300, Total hight mm: 900, Conveyor speed m/min: 20, Drive power kW: 0,8, Year :2015

Manufacturer: CEFLA, Type: TB 2000, Year: 2015, Control: yes, Working length mm: 2000, Working widht mm: 1300, Total hight mm: 900, Total hight mm: 900, Engine power kW: 0,8, Feeding speed min-max m/min: 20, Required space L x W x H mm: 2000x1300x900, Weight approx. kg: ca. 300, Year :2015

Manufacturer: Gottschild, Type: BSD 2000, Year: 2004, Control: Siemens, Monting of the machine: 5 Tellerbürsten, Number of units: 5, Working widht mm: 650, Through running hight max mm: 40, Diameter of brushes: ca.300, Cross-brushing unit: yes, Fast exchange device: yes, Through running hight max mm: 40, kW output motor: ca.1,5, Vacuum belt: yes, Feeding speed continous adjustable: yes, Year :2004

Manufacturer: Hubwagen, Type: 2000 kg, Year: 1989, Fork length in mm: 1150, Width mm: 540, Year :1989

Manufacturer: SR, Type: TM 2000, Year: ca.2000, Lifting power kg: 1000, Length mm: 1500, Width mm: 540 Gabel aussen, Lifting hight approx. mm: ca.150, FREE TEXT: Preis 120 Euro.zzgl.Mwst, Year :ca.2000

Manufacturer: Walther + Cefla UV, Type: Pilot Signier + UV 2000, Spraying line: yes, Work piece width min-max mm: 1300, Spraying machine: Walther, UV dryers - 4 lamps (number): 1,

Manufacturer: Cefla, Type: UV 2000, Year: 2020, Work piece width min-max mm: 1300, Number of lamps: 2+1, Lamps inclined installation: yes, Lamps from below: 1, Conveyor lenght mm: 6500, Working widht mm: 1300, Conveyor lenght mm: 6500, Working widht mm: 1300, Required space L x W x H mm: L-6500, Year :2020

Transnorm belt conveyor GF 2000-1250-1100 RA2390 Technical data: Conveying length (NL): 2000 mm Framework width (NB): 1250 mm belt width (GuB): 1100 mm Framework width including Motor (MB): 1700 mm height (BH): 210 mm Side guides height: 400 mm Drive: SEW gear Motor with Movi-Mot Conveying speed m/s: freely adjustable between 0.5-1.5 m/s Electrical data: 50Hz V380-500, kW 1.1 Optionally available: Supports Prices net plus VAT. ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2018 condition: good (used) Conveying length in mm: 2200 Nominal / outside width in mm: 1120 Belt width in mm: 1000 Driven: YES Engine type: SEW Eurodrive KW: 1,1/S1 Conveyor speed m / s: 0,4-1,3 scope of delivery: including side guides without supports, including Movimot frequency converter For individual, professional advice, simply contact us. Simply contact us by phone ...

Manufacturer: Cefla, Type: UV 2000 M2/1600, Work piece width min-max mm: 1600, Working widht max mm: 1600, Number of lamps: 2, kW power 1 lamp: ca.12, kW power all lamps: 46,25, Lampen gerade eingebaut: 2, Lampen von unten: no, Adjustable: yes, Power per lamp watt UV: 80-120 unter<CRLF>vorbehalt, od distance mm: 80, Conveyor lenght mm: 3000, Outer belt width mm: 2800, Working hight approx mm: 60, Conveyor: Stange, Exhaust air diameter mm: 2, Working height in mm: +/--950, Feedin speed m/min: 5-15, Rod transportation: yes,

Manufacturer: Sorbini, Type: VS/32-BT-S 2000, Year: 1999, Number of units: 2, Working widht mm: 1350, Through running hight max mm: 80, Diameter of brushes: 150, Number of rotations controlled: yes, Units mounted upright: yes, Through running hight max mm: 80, Axle-diameter: 60, Engine power - kW: 1,5, Required space L x W x H mm: 2500 X 1200 X 1600, Type of use: Reinigen oberflächen, Year :1999

Manufacturer: Gubisch, Type: ES 2000, Year: 1991, Control: Hand, Trimming saw: yes, Durchmesser Säge: 400, Saw kW: 3, rotations controlled: 2800, Working hight mm: 120, Vertikal spindle: yes, Working range Z-axis mm: 300, Length lifting spindle mm: 300, Diameter of the spindle mm: 50, Travels of spindle: 2 x100 mm, Milling spindle kW: 50, rotations controlled: 2800, Working stations: 1, Angular adjustment horizontally: yes, Work piece hight max mm: 120, Hauptmotor kW : 7,5, Wight approx. kg: 2000, Vorschub Stufenlos: yes, Mitre Window: yes, Year :1991

Manufacturer: Signode, Type: Spirit 2000, Bauyeshr : 1993, Control: Programm, Belt width mm: 7, Bandabroller : yes, Bandspannung einstellbar : yes, Feeding belt control: yes, Funktionswiederholung : yes, Ausstattung Fahrrollen : yes, Takleistung min : 25, Foot switch: yes, Kartonformat min. L x B x H mm: endlos x 1200 x 1200, Year :1993

x-travel: 2000 mm y-travel: 1500 mm z-travel: 1460 mm Control: Heidemhain type: TNC 426 CB mm Rotary table: 1350x1550 mm turning speeds: 10-3000 U/min spindle taper ISO: 50 Table load: 6000 kg T-slot - width: 28h7 mm T-slot - distance: 150 mm number of T-slots: 150 Feed: 10-3000 mm/min total power requirement: kW weight of the machine ca.: 24 t dimensions of the machine ca.: m B-axis 0.1-1.5 rpm Feed rate 3 rpm The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours a ...