spindle moulder used for sale

Machine number: 10279 Operating voltage: 380 V Connected load: 3 kW Rated current: 25 A Frequency: 50 Hz Spindle speed: 40 - 2800 rpm Centre length: 750 mm Centre height above bed: 150 mm Turning diameter over bed: approx. 300 mm Centre height over support: 100 mm Turning diameter over support: 200 mm Spindle passage: approx. 35 mm Equipment: Tailstock Multifix Type B steel holder, three-jaw chuck (diameter: 160 mm), 2-axis digital display from the manufacturer RSF Reference: Mahle Auction-ID: A7-46763-349

Machine number: 291218 Center width: 760 mm Center height: 205 mm Spindle bore: 58 mm Main spindle Speeds 12: from 20 to 2000 rpm Spindle head mount: CAMLOCK 6 incl. two-axis digital display from the manufacturer FAGOR The machine is equipped with a tailstock, a Multifix turning steel holder and a three-jaw chuck from the manufacturer SMW AUTOBLOK, diameter: 200 mm and a steady rest Reference: Hercegfi - Lot 48 Auction-ID: A7-46763-220

Machine number: 5012221 Center width: 760 mm Turning diameter over bed: 430 mm Turning diameter over face cuts: 240 mm Turning diameter over offset: 690 mm Bed width: 300 mm Spindle bore: 58 mm Spindle speed: 20 - 2000 rpm Longitudinal feeds: 0.05 - 0.82 mm/U Face feeds: 0.02 - 0.4 mm/U Thread (metric): 0.5 - 7 mm Diameter of lead screw: 35 mm Pitch of lead screw: 6 mm Diameter of tailstock quill: 58 mm Tailstock Quill Travel Adjustment: 150 mm Quill Mount: MK4 Reference: Limani/Maric Auction-ID: A7-46763-342

Center length: 500 mm Center height above bed: 150 mm Turning diameter over bed: 300 mm Center height over support: 100 mm Turning diameter over support: 200 mm Spindle passage: approx. 28 mm Equipped with: – Multifix turning steel holder – Four-jaw chuck (Ø 130 mm) – Digital display from the manufacturer HEIDENHAIN Reference: Mahle Auction-ID: A7-46763-350

Operating voltage: 380 V Frequency: 50 Hz Rated current: 12 A Connection: 4.8 kW Spindle speed: 25 – 2000 rpm Center length: 700 mm Center height above bed: 170 mm Turning diameter over bed: 340 mm Center height over support: 130 mm Turning diameter over support: approx. 260 mm Spindle passage: 48 mm Equipment: tailstock, Multifix lathe steel holder, quick-release chuck Incl. collets and various accessories Reference: Weitner Auction-ID: A7-46763-352

Spindle housing: 126 mm diameter/ 105 mm Speed: up to 40,000 rpm Peak power: 6 kW Operating voltage: 380 V Rated current: 10.5 A Frequency: up to 1333 Hz Coolant flow rate: 0.8 l/min Absorption: HSK 40 C Clamping diameter: up to 12 mm (max. 16 mm) This is an article from a training workshop Reference: Training workshop - Lot 5 Dimensions: 720mmx512mmx510mm Weight: approx. 100kg Auction-ID: A7-46763-245

Multi-spindle turning machine manufactured in 1992. This Mazak Quick Turn 18 NSP features a maximum turning diameter of 260 mm and a turning length of 500 mm. It includes a tool turret with 8-fold / 16 positions and a spindle speed range of 36 - 3,600 rpm. If you are looking to get high-quality turning capabilities, consider the Mazak Quick Turn 18 NSP machine we have for sale. Contact us for further details regarding this machine.

Blanchard dia 900 mm Magnetic table dimensions: die 900 mm Motorpower: 25 HP Length : 3300 mm Depth: 1180 mm Height: 3100 mm Weight: 6 ton

The machine works however readout positioning is not good Power supply available Conductor present Tool key included Auction-ID: A1-40977-40

Spindle diameter: 25mm Spindle Angled: Manual Power supply available Tool wrench provided Milling heads available Spindle Speed: Manual Min. spindle speed: 1400 rpm Max. spindle speed : 1200 rpm Min. Tilt: 0° Max. Tilt: 45° Fuse: 32A Power supply available Feeder brand: Holz-her Number of wheels: 3pcs Auction-ID: A1-40977-73

No type plate available - Buyer must provide material to move! Auction-ID: A3-43544-18436

Two Schütte six-spindle turning machines including one Iemca bar feeder are available. 1) Schütte SF 42, year of manufacture: 1977, number of spindles: 6, max. bar capacity: 42mm, max. longitudinal slide stroke: 125mm, speed: 2240rpm, machine dimensions X/Y/Z: approx. 6500mm/1400mm/2200mm, weight: approx. 10000kg. Including pick-off spindle, cams, collets, chip conveyor, oil mist extraction system and Iemca PRA40/33/P bar feeder. 2) Schütte SF 51 DNT, year of manufacture: 1987, max. bar capacity: 51mm, number of spindles: 6, max. turning length: 102mm, max. drilling depth: 102mm, spindle circle diameter: 340mm. Including pick-off spindle, CNC cross slide in position 4, cams, collets, auxiliary coolant pump and chip conveyor. Documentation available. An on-site inspection is possible.

HS9000 High Speed Milling Spindle / Angular Milling Head Type: High speed milling spindle head / angular milling attachment Manufacturer: Nikko / Nikken Model: HS9000 Application: Milling, drilling and machining operations on machining centres or special machines This item is delivered loaded on truck or container. Dismantling and loading costs are specified as additional costs. Auction-ID: A1-47114-29

This 4-axis Muratec MW 100 GT multi-spindle turning machine was manufactured in 2012. It features a maximum turning diameter of 168 mm and a turning length of 145 mm. The machine is equipped with two turrets, each with 8 stations, and a gantry loader for efficient operation. If you are looking to get high-quality turning capabilities, consider the Muratec MW 100 GT machine we have for sale. Contact us for further details.

Engine, each: 4,5 kW Pitch: 600 mm spindle diameter: 30 mm Schneider SK D 2 dual-spindle table router for the precise machining of solid wood and wood-based materials, featuring two independently operable router spindles. The machine enables efficient operation thanks to quick changes between different router bits without setup time. Ideal for versatile milling work in window, door, and furniture manufacturing. Speed settings: 3000/4000/5000/6000/8000/10000 RPM The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

An Inotec spindle press for rolling and forming sheet metal bodies of various sizes is available. Safety distance: 350mm, max. product diameter: 350mm, control system: PLC, weight: approx. 1800kg. Including pressure plate magazine and various tool sets. Documentation available. An on-site inspection is possible.

CNC lathe for turning and machining metal parts. CNC control: Fanuc 16 T AA Max. turning diameter: 165 mm Turning length: 100 – 340 mm Diameter above bed: 220 mm Main spindle speed: 50 – 5,000 rpm Main spindle power: 5.5 / 7.5 kW Main spindle bar passing: 65 mm Sub-spindle speed: 50 – 5,000 rpm Sub-spindle power: 3.7 / 5.5 kW Sub-spindle bar passage: 42 mm C-axis: 0.001° Turrets: 2 Tool positions: 2 × 16 Motorized tools: 2 × 16 positions Strokes: X 175 mm / Z 240 – 680 mm Total power: 41 kVA Dimensions (mm): 3,500 × 2,800 × 2,000 Weight (kg): 5,500 Auction-ID: A1-47716-236

CNC lathe for turning and machining metal parts. CNC control: Fanuc 16 T AA Max. turning diameter: 165 mm Turning length: 100 – 340 mm Diameter above bed: 220 mm Main spindle speed: 50 – 5,000 rpm Main spindle power: 5.5 / 7.5 kW Main spindle bar passing: 65 mm Sub-spindle speed: 50 – 5,000 rpm Sub-spindle power: 3.7 / 5.5 kW Sub-spindle bar passage: 42 mm C-axis: 0.001° Turrets: 2 Tool positions: 2 × 16 Motorized tools: 2 × 16 positions Strokes: X 175 mm / Z 240 – 680 mm Total power: 41 kVA Dimensions (mm): 3,500 × 2,800 × 2,000 Weight (kg): 5,500 Auction-ID: A1-47716-237

Manufacturer: INDEX Year: 2005 Type: Moving spindle CNC lathe with motorized tools and C-axis Numerical control: Siemens Sinumerik 840D Powerline Chuck: Ø 160 mm Max. rotation diameter: Ø 180 mm Strokes: X-axis 520 mm / Z-axis 200 mm Fast feeds: X/Z 40 / 30 m/min Moving spindle: 5,000 rpm – 13 kW (100%) / 20 kW (40% ED) – max. torque 105 Nm C-axis: 0.001° resolution Turret: 12 positions – all motorable stations – VDI 30 Motorized tools: up to 6,000 rpm – 8.5 kW Power supply: 400 V / 50 Hz / 3 phases – installed power approx. 25 kW Weight (kg): approx. 4500 Auction-ID: A1-47716-273

CNC lathe for turning and machining metal parts. CNC control: Fanuc 16 T AA Max. turning diameter: 165 mm Turning length: 100 – 340 mm Diameter above bed: 220 mm Main spindle speed: 50 – 5,000 rpm Main spindle power: 5.5 / 7.5 kW Main spindle bar passing: 65 mm Sub-spindle speed: 50 – 5,000 rpm Counter-spindle power: 3.7 / 5.5 kW Counter-spindle bar passage: 42 mm C-axis: 0.001° Turrets: 2 Tool positions: 2 × 16 Motorized tools: 2 × 16 positions Strokes: X 175 mm / Z 240 – 680 mm Total power: 41 kVA Dimensions (mm): 3,500 × 2,800 × 2,000 Weight (kg): 5,500 Serial No.: 1105-02957 Auction-ID: A1-47716-238

Maximum passage diameter: 310 mm Maximum turning diameter: 190 mm Standard turning diameter: 170 mm Maximum turning length: 235 mm Bar passage: 65 mm Spindle speed: 50 to 5,000 rpm Spindle power: 22 kW / 18.5 kW Spindle nose: JIS A2-6 Spindle Bore: 73 mm Axis C: Indexation 0.001° Turrets: 2 independent turrets Tool capacity: 32 positions (16 per turret) Motorized tools: 16 positions per turret Motorized Tool Speed: 6,000 RPM Power with motorized tools: 5.5 / 2.2 kW Indexing time: 0.2 s X-axis: 140 mm Y-axis: ± 50 mm Z-axis: 700 / 690 mm B-axis: 775 mm Fast Advances: 18 m/min CNC Control: MSX 501 MAPPS II (Fanuc 30i) Weight: 6,600 kg Dimensions: 3,700 x 2,100 x 2,000 mm Equipment: Bar feeder included Auction-ID: A1-47716-15

Kistler NC joining module with double station/spindle unit Kistler NCFH 60 servo press with feed carriage & spindle station The Kistler NCFH 60 NC joining module is integrated into an industrial double station/spindle unit for automated series production (e.g. friction welding or precision pressing). The system is characterized by the highest precision, integrated force-displacement monitoring (piezoelectric sensors) and an extremely robust design for continuous industrial loads. Precise press-fitting and joining: Ideal for high-precision assembly processes in the automotive industry, electrical manufacturing or general mechanical engineering. Integrated quality assurance (force-displacement monitoring): Thanks to the built-in piezoelectric sensors, the module measures the exact tensile and compressive forces during the pressing process depending on the position.  ...

with foot control Auction-ID: A1-46626-31

Drilling head Multi-spindle horizontal variable centre distance 1 pneumatic cylinders Parts Pressers 1 pedal to trigger Drilling and clamping Auction-ID: A1-47766-22

Manufacturer: Heidenreich & Harbeck (VDF), Hamburg , Type: 18 RO , Year of construction: 1960 , Working range: Center width: approx. 1,000 mm , Circulation over bed: approx. 360–380 mm , Circulation over support: approx. 200 mm , Speed range: 28 – 1,250 rpm , Multi-stage mechanical transmission , 3-jaw chuck Forkardt Ø200 mm , Operating voltage: 380 V ; Control current: 220 , frequency: 50 Hz I ; PhotosTotal current: approx. 4 A , Equipment: Multifix quick-change holder , Type B several rotary holders and drill holders ,Forkardt 3-jaw chuck Ø200 mm , extensive tool equipment , see photos for more details Auction-ID: A7-47753-600

Lead and pull spindle lathe - 3-jaw chuck 200mm - Quick-change steel holder - Bezel - Machine light - Chip tray - Grain tip Turning diameter over bed 480 mm Turning diameter over support 260 mm Turning length 1500 mm Turning diameter in the offset - mm Speed 90 - 1120 rpm Tip height 240 mm Spindle bore 52 mm Total power requirement 7.5 KW Machine weight approx. 2.3 t Space requirement approx. 3.0 x 1.3 x 1.5 m Auction-ID: A7-47818-734

Technical data Manufacturer: HAMLET Model: Primus Machine Type: Precision guide and pull spindle lathe Type: Conventional lathe Center height: approx. 125 mm (Source: online) Circumferential diameter over bed: approx. 250 mm (Source: online) Circumferential diameter over support: approx. 130 mm (Source: online) Center width: approx. 500 mm (Source: online) Spindle bore: approx. 28 mm (Source: online) Speed range: 60–3000 rpm (source: online, rev plate visible) Motor power: approx. 1.5–2.2 kW (Source: online) Configuration 3-jaw chuck Multifix quick-change steel holder Tailstock Machine Light Base frame with switching unit Various tool holders and drill chuck holders Accessory kit according to photos Note There are no original documents or technical documentation available for the machine. The technical data provided have been researched ...

Technical data Lead and pull spindle lathe Manufacturer: NARDINI Type: ND 220 AE Speed range: 25 - 2000 rpm Electrical connection: 380 V / 50 Hz Connected load: 6.3 kW 3-jaw chuck Ø approx. 250 mm Configuration With guide and pull spindle With tailstock With quick-change steel holder Tapping device available Feed and thread tables on the machine Integrated machine substructure Emergency stop switch available Machine with splash guard Auction-ID: A7-47277-3016

Technical data Manufacturer: EMCO Model: Maximat Super 11 Speeds: 55 / 110 / 200 / 300 / 410 / 600 / 1100 / 2200 rpm 8 speed levels Digital display: ELESTA VISULESTA II E Hardened machine bed Configuration 3-jaw chuck available Additional 3-jaw chuck Collet holder with collet set Quick-change steel holder Tailstock available Accessories with tool holders and tips Machine in used condition Auction-ID: A7-47277-3061

WEILER Matador VS2 Lead and Pull Spindle Lathe Serial Number: 7351 Center width: 500 mm Tip height: 140 mm Circulation over bed: 295 mm Circulation over bed slide: 280 mm Circulation via face slide: 160 mm Turning length: 470 mm Spindle bore: 36 mm Max. workpiece weight: 80 kg Spindle speed range: 15 – 3550 rpm Quill diameter: 40 mm Quill stroke: 85 mm Auction-ID: A7-47533-124

Technical data Manufacturer: HAMLET Machine type: Lead and pull spindle lathe 3-jaw chuck mounted Lead screw and pull screw available Threading device available Interchangeable wheel arch available Configuration Collet set included in the base Extensive accessory package with interchangeable wheels Tailstock available Upper slide available Longitudinal and plane feed Compact precision lathe in heavy-duty casting design Auction-ID: A7-47277-3011

Technical data Manufacturer: NOTTMEYER Machine Type: Hole Row Drilling Machine Number of Spindles: 77 Drilling depth: 12 mm Table size: approx. 3000 x 950 mm Dimensions: approx. 3350 x 1000 x 1500 mm Motor power per visible drill motor: 1.1 kW Voltage per visible drill motor: 380 / 220 V Speed per visible drill motor: 2820 rpm Configuration Hole row drilling machine with multiple drill spindles, pneumatic actuation, foot control, and existing drills/drill bits. Auction-ID: A7-47854-4

Technical data Manufacturer: MATRA Type: MD 22 Machine type: Lead and pull spindle lathe Voltage: 380 V Frequency: 50 Hz Control voltage: 220 V Rated current: 17 A Fuse: 25 A Main motor: AEG AM 132 MR4 Motor speed: 1445 rpm Degree of protection: IP54 Speed range: approx. 100 – 2000 rpm Turning length: approx. 1500 mm Configuration 3-jaw chuck available Tailstock available Steel holder available Guide and pull spindle available Heidenhain digital displacement measuring system available Machine mounted on machine foot Used condition Auction-ID: A7-47277-3000

Technical data Manufacturer: KNUTH Model: Basic 170 Super Machine Type: Lead and pull spindle lathe Center width: approx. 700 mm Dimensions: approx. H1300 x W700 x L1700 mm Configuration Three-jaw chuck mounted Tailstock available 4-fold tool holder available Machine light available Additional three-jaw chuck available Lathe chisel set available Dial gauge with magnetic base available Rotating centering tip available Various clamping devices and tool accessories available Auction-ID: A7-47277-3109

Technical data Manufacturer: WEILER Model: Matador VS1 Speed range: 30 - 3550 rpm 16 speed levels Electrical connection: 380 V Dimensions approx. 1500 x 700 x 1550 mm Configuration 3-jaw chuck HEIDENHAIN Digital Display Tailstock with drill chuck Quick-change steel holder Collet set in the base cabinet Accessories with tips, jaws and tool holders Protective cover on the chuck Machine in used condition Auction-ID: A7-47277-3058

WEILER primus LZ-G Lead and Pull Spindle Lathe (1978) Serial Number: 722 Center width: approx. 500 mm Tip height: approx. 125 mm Circulation over bed: approx. 250 mm Speed range: 90 – 3000 rpm Feel free to take a look at the videos about this machine Auction-ID: A7-47533-121

Technical data Manufacturer: WEILER Model No.: Matador Turning diameter over bed: 260 mm Speed range: 15 - 3550 rpm 34 speed levels Dimensions approx. 1500 x 800 x 1650 mm Configuration 3-jaw chuck HEIDENHAIN Digital Display MULTI SUISSE quick-change steel holder Tailstock available Collet set in the base cabinet Accessories with tips, clamping devices and tool holders Machine in used condition Auction-ID: A7-47277-3060

Technical data Manufacturer: WEILER Model No.: Intern 140 Machine No.: 85140112 Operating voltage: 380 V Control voltage: 220 V Connected load: 2.2 kW Frequency: 50 Hz Speeds: 630 / 1000 / 1600 / 2500 rpm Center width approx. 800mm Configuration 3-jaw chuck Tailstock available Multifix tool holder HEIDENHAIN Digital Display Coolant Setup Base frame with storage space Accessories and interchangeable wheels in the base cabinet Machine in used condition Auction-ID: A7-47277-3056

OPTIMUM TH 4610 Lead and Pull Spindle Lathe (2018) Serial Number: J0517120461 Tip width: 1060 mm Tip height: 230 mm Circulation over bed: 460 mm Circulation over slide: 270 mm Turning length: 240 mm Bore main spindle: 58 mm Max. workpiece weight: 300 kg Morse taper of main spindle: MK6 Spindle speed range: 25 – 2000 rpm Facing slide travel 285 mm Upper slide travel: 125 mm Quill diameter: 60 mm Quill path 130 mm Cone in the quill: MK4 Diameter of three-jaw chuck: approx. 200 mm Feel free to take a look at the videos about this machine Auction-ID: A7-47533-118

: neu : ca. 4 Monate ab Auftragse : Bulgarien : 113620 € : 2147.42 € : 800 mm : 2000 mm : 400 mm : 260 mm : 560 mm : 560 mm : 318 MK : 12 : 8 - 400 1/min : 152 : 0.039 - 15 mm/U : 0.02 - 7.5 mm/U : 76 : 0.5 - 150 mm : 60 - 1/5 Gänge/ : 0.125 - 37.5 : 240 - 4/5 : 410 mm : 150 mm : 105 mm : 6 MK : 225 mm : 11 kW : 6000 kg Their main purpose is to process pipes. Accordingly, this type of machines is widely used in the oil industry. Oil country lathes have large capabilities of processing inner and outer cylindrical and conical threads on pipes with large diameters. The clamping of the pipes with two universals and stands allows the processing of long pipes. These lathes are suitable for producing elements and equipment for the oil industry, as well as for maintaining such facilities. Drive via gearbox Electrodynamic brake 3-axis digital display Fagor Quick-change tool holder Amestra ty ...

Key data: 6 1/min

turning dia. 48 mm

Lead & Pull Spindle Lathe / WEILER COMMODOR 230 AC -CE marking -Year of construction 2002 -Tip height 230mm -Circumferential diameter over bed 475mm -Circumferential diameter over face slide 270mm -Tip width 1000mm -Spindle speeds 25 - 2000 rpm -Automatic longitudinal/plane feeds -Tapping/Metric/Inch/Module etc. -Spindle head Din 55027 / size 6 -Tailstock MK 4 -Drive power 11KW -Electric lining protection -Multifix base holder with inserts -Three-jaw chuck -Swarf back wall with work light -2x Emergency / Off -Coolant device -Machine feet -Documentation Dimensions: LxWxH 2.6x1.1x1.6 meters / Weight 1900Kg

: neu : ca. 4 Monate ab Auftragse : Bulgarien : 138800 € : 2623.32 € : 1020 mm : 2000 mm : 510 mm : 358 mm : 770 mm : 560 mm : 361 MK : 12 : 6,3 - 315 1/min : 152 : 0.039 - 15 mm/U : 0.02 - 7.5 mm/U : 76 : 0.5 - 150 mm : 60 - 1/5 Gänge/ : 0.125 - 37.5 : 240 - 4/5 : 505 mm : 270 mm : 105 mm : 6 MK : 225 mm : 18.5 kW : 6400 kg Their main purpose is to process pipes. Accordingly, this type of machines is widely used in the oil industry. Oil country lathes have large capabilities of processing inner and outer cylindrical and conical threads on pipes with large diameters. The clamping of the pipes with two universals and stands allows the processing of long pipes. These lathes are suitable for producing elements and equipment for the oil industry, as well as for maintaining such facilities. Drive via gearbox Electrodynamic brake 3-axis digital display Fagor Quick-change tool holder Amest ...

number of spindles:6 spindle passage:22 mm ?Bar feeder complete is 4.70 meters - for 3 meters of material ?The machine is still on ?Materail to be processed on the machine: Steel ?Production with OIL Machine has only Single-NCU without PCU. The complete energy supply of all 6 main spindles was replaced in April 25. No socket for powered tools!

number of spindles:8 spindle passage:67 mm Cam controlled multi spindle automatic lathe, used 8 main spindles pick up in pos. 8 threading attachment CNC compound slide in pos. 5, also 2. speed in pos. 2 Hydraulic spindle brake in pos. 4 Incl. length measurement, incl. Brankamp cutting force monitoring tooling: could be different like pictures Please, contact us for getting more informations and pictures on mail@tar-mc.com or www.tar-mc.com

: neu : ca. 4 Monate ab Auftragse : Bulgarien : 113720 € : 2149.31 € : 800 mm : 2000 mm : 400 mm : 315 mm : 560 mm : 560 mm : 318 MK : 12 : 8 - 400 1/min : 152 : 0.039 - 15 mm/U : 0.02 - 7.5 mm/U : 76 : 0.5 - 150 mm : 60 - 1/5 Gänge/ : 0.125 - 37.5 : 240 - 4/5 : 410 mm : 150 mm : 105 mm : 6 MK : 225 mm : 11 kW : 6100 kg Their main purpose is to process pipes. Accordingly, this type of machines is widely used in the oil industry. Oil country lathes have large capabilities of processing inner and outer cylindrical and conical threads on pipes with large diameters. The clamping of the pipes with two universals and stands allows the processing of long pipes. These lathes are suitable for producing elements and equipment for the oil industry, as well as for maintaining such facilities. Drive via gearbox Electrodynamic brake 3-axis digital display Fagor Quick-change tool holder Amestra ty ...

number of spindles:8 spindle passage:51 mm Article: multi spindle automatic lathe Manufacturer: Schütte Type: AF51 Yob: 1987 eight main spindles max. bar diameter D=51mm control SIEMENS SIMATIC S5 pick up in pos. 7, for rear machining thread cutting drive independent feed in positions 2/3 electronical trip dog control ?Balluff? clear text display Wöhrle coolant pump magnetic cartridge filter oil running incl. bar loader IEMCA PRA 40/37/F, yob 1987, (bundle type) Painting in light blue and light grey The configuration of tooling will be different like pictures. Please, contact us for getting more information and pictures on mail(at)tar-mc.com or www.tar-mc.com

Article: CNC-controlled multi-spindle automatic lathe Manufacturer: Tornos Type: MultiSwiss 8x26 Yob: 2016 full cross slide configuration, counter spindle, part-pre-drawing device, 2 x driven tools, 3 x Y-axis, 1 rigid backworking, 1 x driven backworking, 2x 80 bar high pressure pumps optional: setting robot, manufacturer HandlingTech. The scope of delivery regarding the tooling equipment could be different like pictures. Please, contact us for getting more informations and pictures on mail@tar-mc.com or www.tar-mc.com

WEILER COMMODOR L&Z Spindle Lathe -Turning length 1000mm -Turning diameter max. 160mm Bar Passage 56mm -Speed range 25-2000 rpm -Automatic longitudinal/plane feeds - Thread: Metric/Inch/etc. -Tailstock Mk4 Hjbkn Au Ssun Ulhs Tsl -Three-jaw chuck approx. 250mm -Multifix base holder with insert -Coolant device -Electric lining protection -Swarf back wall -Machine documentation -Good operational condition Dimensions: LxWxH 2.5x1.3x1.7 meters / Weight 1500Kg

Article: CNC-controlled multi-spindle automatic lathe Manufacturer: Tornos Type: MultiSwiss 8x26 Yob: 2019 full cross slide configuration, counter spindle, part-pre-drawing device, 2 x driven tools, 1 rigid backworking, 1 x driven backworking, 2x 80 bar high pressure pumps optional: setting robot make HandlingTech. The scope of delivery regarding the tooling equipment could be different like pictures. Please, contact us for getting more informations and pictures on mail@tar-mc.com or www.tar-mc.com