spi used for sale

Feeding Technology / Feeding System / Vibratory Conveyor / Sorting Device / Spiral Conveyor Vibrating Cup, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwdriving TechnologyFeeding System DEPRAG Type: 0622-P/0,75-1SNr: 1183884 2011 - 2012The system was used for feeding electrical plug contact pins. Product dimensions: 4 mm, length 26 mmThe pins are stored in the material hopper, the feed belt conveys the pins into the spiral conveyor as required.

Fine boring head, spindle tool, boring head, bridge tool, fine boring headBoring tool, spindle headBoring tool, spindle headBoring rodReceptacle for bridge tool = SECO - epb GRAFLEX (Made in France) Type A731 200Boring head for bridge tool = SECO - epb GRAFLEX (Made in France) Type A731-010Boring block for bridge tool = SECO - epb GRAFLEX (Made in France) Type A731-500Counterweight for bridge tool = SECO - epb GRAFLEX (Made in France) Type A731-600Tool holder: GRAFLEX Holder size G7 = 46 mmProcessing diameter: 200-280 mmAdjustment accuracy: 0.01

Drive motor, DC servo motor LENZE type GFQBT 80-24Spindle motor, electric motor, main spindle motorSeries No. 184592 Year of construction: 1993Nominal power: 4.2 kWook voltage: 260 V DCNoth current: 20 ampereMaximum speed: 3000 rpm. Excitation voltage: 200 V DCexcitation current: 1.15 ampere electric brakeShaft diameter: 24 mm (shaft with 8 mm key)Shaft length: approx. 47 mm (shaft protrusion from centering edge)Centering flange diameter: 110 mmBolt circle diameter: 130 mm, 8 x M8 threaded encoder, speedometer, GBR

Vibratory Spiral Conveyor / Sorting Device / Spiral Conveyor / Vibratory Conveyor RNA Shaking Bowl, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwing TechnologyFeeding System, Feeding DeviceManufacturer: RNA Rhein-Nadel Automation GmbHTyp: SRC-N 250-2LSer.- No: 03611 Year of Construction: approx. 2000Pot Diameter Bottom: 300 mmPot Diameter Top: 350 mmPot Inner Height: approx. 25 mmSorting Track Width: approx. 30 mmTotal Height (Drive + Pot with Sorting Path): 380 mmOscillation Frequency: 100 Hz / 6000 min-1Power supply: 230 volts, 50 Hz- The

turning diameter: 60 mm turning length: 200 mm number of slides: total power requirement: 20 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 410 mm turning diameter over slide rest: 240 mm turning length: 1000 mm turning diameter in the gap: 530 mm turning speeds: 65 - 1810 U/min centre height: 205 mm spindle bore: 52 mm tailstock quill taper MT: 4 total power requirement: 2,2 kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1,9 x 0,8 x 1,3 m Center lathe with: 3-axis digital measuring system fully assembled electromagnetic main spindle brake auto. Feed in longitudinal and transverse direction safety relay Micrometer end stop coolant device 3-jaw lathe chuck with 1 set of turning and drilling jaws German operating instructions. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 400 mm turning diameter over slide rest: 264 mm turning length: 1000 mm turning diameter in the gap: 550 mm turning speeds: 44 - 2000 U/min centre height: 200 mm spindle bore: 52 mm tailstock quill taper MT: 4 MK connected load frequency: 400 V total power requirement: 1,5 / 2,4 kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1,9 x 0,8 x 1,56 m 3-axis digital display 3-jaw chuck 200 mm. 4-jaw chuck 200 mm. Faceplate 320mm bezel fixed running bezel 4-fold steel holder. Halogen machine light machine light foot brake removable chip tray, chip protection wall Hardened and ground bed tracks Complete coolant system lining protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 320 mm turning diameter over slide rest: 200 mm turning length: 900 mm turning diameter in the gap: 320 mm turning speeds: 75 - 2000 U/min centre height: 160 mm spindle bore: 38 mm tailstock quill taper MT: 3 connected load frequency: 400 V total power requirement: 1,5 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 1,6 x 0,75 x 1,7 m SINO digital display 3-jaw chuck 200 mm. 4-jaw chuck 200 mm. Faceplate 250mm bezel fixed Quick-change steel holder with 4 pcs. steel holder machine light Chip tray, chip protection wall Hardened and ground bed tracks lining protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

8-spindle lathe, Number of spindles: 8

multi spindle bar automatic, Mori Say 8/42 - YOM 2006, CONFIGURATION, - HIRTH coupling for drum locking, - 8 front slides and 8 radial slides, - 4 Compond slides in stations 1, 2, 5, 6, - CUCCHI Pietro bar loader (2007), - Bundle for CUCCHI BLT BUNDLE bar loader (2018), - Pick-up spindle, hydraulic in pos. 8, - preparation for oil fume extraction

- neu aufgebaut, neue Elektrik in 2018, - Schnecken-Späneförderer, - Ölnebelabsaugeinrichtung, - Kühlmittelfilter, selbstreinigend, - Doppelschlitten in Lage 6 zum Abstechen und Rückseitenbearbeitung, - Polygondreh- und Gewindefräseinrichtung Lage 4, - CNC-Kreuzschlitten AUTOR in Lage 5, - Abgreifspindel, hydraulisch in Lage 6, - Transportband für Fertigteile, - Stangenlader Iemca PRA

!bargain price!

Schütte 32 multi-spindle lathe, completely rebuilt by GWM-Tech, Fanuc AC motors, FANUC motors for threading, PLC, pick-up spindle chuck, bar loader Cucchi Pietro

Hydraulick pickup spindle pos. 6, Clutch for threading, Auto bar loader: Pietro Cucchi

Number of spindles: 6, Max bar diameter [mm]: 25, Spindle speed [rpm]: 4.250, Weight of the machine ca. [kg]: 7.150, Auto bar loader: Cucchi BLT Multi F-6

Gildemeister GMC20 ONE, Options / Accessories, - 5 Cross-slides pos. 1;2;3;4;5, - 2 Radial slides pos. 6 for cutting and rear-working operations, - 1 C-axis for the pick up spindle, - Pneumatic work-piece unloading chute for pos. 6, - Work-piece conveyor belt, - Swarf conveyor, worm type, - 5x Frontal tool spindle, fix, - Pick- up spindle in pos. 6, - High pressure coolant device 70l / 50bar, Country of origin: Italy, Control: Siemens 840D, Number of spindles: 6, Max bar diameter [mm]: 25, Spindle speed [rpm]: 6.000, Spindle motor [kW]: 9,1, Z - travel [mm]: 70 / 140, Total power requirement [kVA]: 98, Weight of the machine ca. [kg]: 9.800, Auto bar loader: Cucchi Giovanni DBM.625

6 spindle bar automatic Gildemeister GS20, compound slide with drive in pos. 1, compound slide with drive in pos. 2, compound slide in pos. 4, compound slide in pos. 5, 4x axial spindle (pos. 1, 2, 4, 5), rotating milling device in pos. 3, pick-up spindle pos. 6, swing rear machining arm drive in pos. 3, swing rear machining arm drive in pos. 6, swarf coneveyor, worm type, set of tool holders, set of cams, Number of spindles: 6, Max bar diameter [mm]: 20, Max bar feed [mm]: 100, Spindle speed [rpm]: 214 - 5.168, Spindle motor [kW]: 11, Weight of the machine ca. [kg]: 5.000, Auto bar loader: Pietro Cucchi

Number of spindles: 6, Max bar diameter [mm]: 20, Spindle speed [rpm]: 500 - 6.000, Weight of the machine ca. [kg]: 5.000, Auto bar loader: Iemca SIR 25 P 33

Gildemeister GM 16-6AC, 4x compound slide - Pos.1; Pos.2; Pos.4; Pos.5, 4x indipendent feed - Pos.1; Pos.2; Pos.4; Pos.5, threading device, 1x threading spindle, pick-up spindle, broaching device, set of cams, set of collets, bar-loader Cucchi Giovanni (YOM 2004), Working hours: 13.600

- spindle drum locking by means of a triad of HIRTH-type rings, - central lubrication system, - spindle stop attachment for main spindles, - cross drill device pos. 4, - 6 indipendent frontal slides, - 4 compound slides in pos. 1, 2, 4, 5, - 2 radial slides in pos. 3, 6, - double slide in pos. 6, - pick-up spindle pos. 6, - pick-up spindle stop attachment pos. 6, - conveyor belt for finished parts, - chip conveyor, hinged belt type, - high pressure coolant system, - removable coolant fluid tank, - bar stock reel for bar length 3 m, - various camms, - various gears, Number of spindles: 6, Max bar diameter [mm]: 32, Spindle speed [rpm]: 250 - 4.250 (250 - 3.350), Spindles interaxis [mm]: 276, Max bar feed [mm]: 125, Weight of the machine ca. [kg]: 9.500

- spindle drum locking by means of a triad of HIRTH-type rings, - central lubrication system, - spindle stop attachment for main spindles, - 2x spindle positioning attachment (pos. 6 + 7), - 8 indipendent frontal slides, - 4 compound slides in pos. 1, 2, 5, 6, - 4 radial slides in pos. 3, 4, 7, 8, - double slide in pos. 8, - 2x pick-up spindle (pos. 4 + 8), - 2x pick-up spindle stop attachment (pos. 4 + 8), - threading attachment, - chip conveyor, hinged belt type, - high pressure coolant system, - removable coolant fluid tank, - bar stock reel for bar length 3 m, - various camms, - various gears, - electrical preparation for auto bar loader, Number of spindles: 8, Max bar diameter [mm]: 32, Spindle speed [rpm]: 270 - 3.750 (270 - 3.200), Spindles interaxis [mm]: 360, Max bar feed [mm]: 125, Weight of the machine ca. [kg]: 11.500

Gildemeister GM20, Country of origin: Italy, Operating hours: 0, Number of spindles: 6, Max bar diameter [mm]: 20, Auto bar loader: Cucchi Giovanni alternative IMG Easy load

Sliding table saw and table milling machine Felder KF 700 S YOC 2024 Format carriage length 2500 mm Motor/Voltage 5.5 kW / 7.5 HP / 400 V Scoring Ø 120 mm X-Roll Sliding Carriage Cutting width 850 mm with digital display Electromotive height adjustment Saw blade swivel 45° manual adjustment Saw blade Ø 315 mm Motor/Voltage 5.5 kW / 7.5 HP / 400 V Cutting height max.110 mm Table milling machine motor 5.5 kW Spindle tiltable 0-45° Left/right rotation selectable Speed 3500 / 6500 / 8000 / 10 000 rpm Max tool diameter 230 mm Spindle diameter 30 mm Total weight approx. 700 kg

11 litre, Stock number: R1108, Litre: 11, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 1 pc., Item: Drum mixer, Standing: On stainless foot, Dimensions: L 490 x W 420 x H 450 mm., Manufacturer: Spicer, Model: Table model, Other: Stainless drum with cover in end bottom and with Timer function

Used spiral mixer DIOSNA, type: SP 80 D -completely overhauled- - for 80 kg of dough or 50 kg of flour - Stainless steel spiral - Stainless steel boiler - 2 Time clocks - 2 speeds - 1 reverse gear - Emergency stop switch - With center wheel for driving the machine - Kettle and kneading arm without Riesse - new electrics, new V-belts, repainted -El. Connection: 400 V, 3PH, 50 Hz, 14 A - Motor: 6 kW - Condition: Very good condition - 6 months warranty A video of the machine in operation can be made on request. Inspection and test run are possible by arrangement.

workpiece diameter: 350 mm workpiece weight: 99999999 kg workpiece height: 240 mm total power requirement: 7,5 kW weight of the machine ca.: 2 t dimensions of the machine ca.: m Seltene Gelegenheit: Teilüberholte Hochpräzisions-Rundtischflachschleifmaschine Rundtisch-Durchmesser 380mm Magnet-Durchmesser 350mm Schleifscheibenabmaße 300x25x76,2mm Tischdrehzahl variabel max. 200U/min Schwenkwinkel des Tisches +-3 Grad Schleifspindeldrehzahl 800-4200 U/min Leistung Schleifspindelantrieb 5KW Verfahrweg quer max. 225mm Verfahrweg vertikal max. 480mm Abstand zwischen Magnetspannfutter und Spindelmitte, max. 390mm Automatischer Kopfabrichter AF65: zum zylidrischen Abrichten der Schleifscheibe im CD-Abrichtverfahren (Abrichten während des Schleifprozesses) Hierdurch werden Schleifzeiten reduziert und Abrichtzeiten eingespa ...

50 litre, Stock number: R1152, Litre: 50, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 1 pc., Item: Drum mixer, Standing: In stainless cabinet on wheels, Bottom: Stainless drum with cover in the bottom end, Manufacturer: Spicer, Type: 50, Other: Safety shielding and timer function

SPECIFICATIONS: Table size: 2400 x 900 mm Extendable table 1 4-roller drive (with variator) Installed power: 5 kW Lockers Ø 35 mm Motorized spindle tilt +/- 45° Motorized height adjustment Dornfix clamping system

Stock number: A201, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 2 pcs., Item: Tube heat exchanger, Outer dimensions: L 3000 mm., Connections: Ø 2, Temperature: Max 180° C, Manufacturer: Tetra Spiraflo, Type: Monotube 2/2,5-30, Year: 1989

SCM T130E spindle moulder Spindle diameter 40mm Overall length of spindles 180mm Spindle speed variable by inverter up to 10,000r.p.m Main motor power 7.5kw Spindle rotation right and left Electronic spindle height adjustment Electronic setting of fences Electronically adjustable roller feed 4-roller feed Maggi Variosteff 4 Feed speed control via variator CE Certified DTR documentation Year of production 2004

pressure capacity max.: 80 t Stroke: 500 mm table surface area: 960 x 810 mm spindle pitch: 72 daylight between the columns: 950 / 540 mm passage: 640 mm machine weight ab.: 4500 kg dimensions of the machine ca.: 2,0 x 2,0 x 3,85 m Hydraulic quick adjustment 500mm Flywheel Ø2000mm 4 prism bases for straightening waves different support frames The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Spiralbindemaschine - Spiral binding machine FOELL 33

Antike Spindelpresse - Antique Spindel Press Krause 35286 Baujahr / Year ca. 1934 - Serial-No. 35286 Pressfläche / Press Size max. 400 x 500mm Wunderschön verarbeitete antike Spindelpresse  Beautifully crafted antique Spindel Press

power capacity: . kW tool adaptor: . total power requirement: . kW Milling head BFT Burzoi 0038 PUN 181-187 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

power capacity: . kW tool adaptor: . total power requirement: . kW Milling head BFT Burzoi 0038 PUN 181-187 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Spindle moulder with tilting shaft SCM mod. T110I - CE -Volt. 400/50 - Matr. AB/118120 - Year 1998

SAC SUERI fixed shaft spindle moulder mod. TS110 - CE compliant - Extended 2400 mm plates. -Volt. 400/50 - Matr. 9813 - Year 1998 - M42 - Complete with manual and CE declaration

WEINIG 5-spindle moulder mod. PROFIMAT P23E – CE compliant -Composition: - Oriz. Inf. 5.5Kw -Vert. right/left 7.5Kw - Oriz. sup. 7.5Kw - Oriz. Inf. 4 Kw - Width 230mm - ATS system - Year 1997 (CE)

Polyester fiber production line Polyester fiber production line, manufactured in 2008, put into operation in 2010. From the end of 2012 until the second half of 2019, fiber production was suspended. The productivity of the line is 10,000 tons of fiber per year. The possibility of producing fiber from primary raw materials - PET granules and from secondary raw materials - PET flakes (recycled PET bottles). The main default raw material (as cheaper) is PET flakes. The available spinneret can be used to produce solid fiber 3, 7 and 15 denier, and hollow fiber, 7 and 15 denier. Hollow fiber can be produced in the "conjugated" type. Can buy and use other denier spinnerete according needs. The main components of the line: Fiber extrusion line • Vacuum dryers, volume 8m3, heated with thermal oil, year of manufacture 2011 – 4 units. + In 2019 instaled, elevators and a screw conveyor for  ...

WEINIG 5+1 spindle moulder mod. PROFIMAT 23 FORTEC - CE compliant - Complete with ATS device - 1st lower horizontal shaft - 2nd vert. Dx - 3rd vert. Sx - 4th upper horizontal - 5° lower horizontal - 6th universal - Width 230 mm. - Cardan drive - Year 2002

SUB: FOR SALE... CHRIS MARINE VALF SPINDLE GRINDING MACHINE AT TURKEY HAVE A GDY SIR WE VE 1 PC USED CHRIS MARINE VALF SPINDLE GRINDING MACHINE AT TURKEY TYPE BSP-2 NO. 463/204 DATA 3X 440V 60HZ IT WAS USED VERY LESS HOURS IF YOU HAVE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurlubay Regards; Aliaga marine services E-mail: infoaliagamarine.com PHN/fax: + 90 232 618 03 88 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

X-axis travel mm: 260 Z-axis travel mm: 590 B-axis travel mm: 624 Turning length mm: 515 Max. turning diameter mm: ø: 366 Swing over bed mm: ø: 923.8 Swing over cross-slide mm: 755 Bar work capacity mm: 52 Upper turret Number of tool slots St .: 16 Speed driven tools RPM: 6.000 Drive power driven tools kW: 5.5/5.5/3.7 (3min/5min/cont) Indexing time s: 0.25 Main spindle Speed spindle rpm: 6.000 Drive power spindle kW: 11/7.5 Spindle bore mm: 61 Chuck type: Hollow Chuck (6") Manufacturer: KITAGAWA Spindle nose: JIS A2-5 Counter spindle Speed spindle rpm: 6.000 Drive power spindle kW: 11/7.5 Spindle bore mm: 43 Chuck type: Hollow Chuck (6") Manufacturer: KITAGAWA Coolant system Tank capacity liter: 235 Equipment Chip conveyor Signal lamp High pressure pump Chuck foot switch (double) for main and counter spindle Interface for ...

Multi-speed machine with flexible shaft BIAX type MB 4-2Masch. No. 9/50/55 Year of construction approx. 1970Length of the flexible shaft: 2 metersSpeed: 900 - 9000 rpm. infinitely variableMotor speed: 3000 rpm. Motor power: 1.2 kW = 1.5 HPerg connection: 380 volts, 50 Hz- handle straight grinder with collet 6 mm- swivel and rotatable foot transport trolley with 2 drawersOverall dimensions: 850 x 550 x 1100Weight: approx. 80 kggood conditionUniversal for milling, grinding and polishing work; used

Ball screw with servo motor SIEMENSLinear guide with permanent servo motor SIEMENSTyp: 1FK6044-7AH71-1EG0Ident No. YF RN22 5076 01 001Year of construction: 2003Axle movement: 540 mmTotal length: 900 mmShaft diameter: 40 mmThread pitch: 40 mmBall diameter: approx. 6 mm- Compact unit with servo motor and spindle nut- Ball screw guided in a torsion-proof manner, drive via nut- Ball screw 40 mm (hollow shaft, inner diameter = approx. 22mm)- Permanent servo motor SIEMENS type: 1FK6044-7AH71-1EG0 (Serial No.: Ident No. YF RN22 5076

Drive motor, DC servo motor LENZE type GFQUBT 112-22Spindle motor, electric motorSeries No. 0239398K Year of manufacture: 1993Nominal power: 6 kWook voltage: 400 DCNenncurrent: 18 ampereMaximum speed: 1000 rpm. Excitation voltage: 210 VDCEexciter current: 3.4 ampereShaft diameter: 38 mm (shaft with 10 mm key)Shaft length: approx. 76 mm (shaft protrusion from centering edge)Centering flange diameter: 230 mmBolt circle diameter: 264 mm, 4x 14 mm holesLonglife speedometer HÜBNER type TDP 0.2 LT-4Speedometer voltage: 60V / 1000

DC main spindle drive, power converter device with digital control Simoreg V55Spindle module, drive controller, rectifier, DC regulatorManufacturer SIEMENSTyp SIMODRIVE 6RA2725-6DV55-0 D380/60 Mreq-GdG6V55-3A0Version V55 Basic unitInput voltage 3 AC 380 V Input frequency 50 / 60 HzInput current 49 AAoutput voltage 380 VDCAoutput current 60 ANenn power 22 kWAbdimension (W x H x D) 270 x 260 x 290 mmWeight approx. 25 kgThe drive controller is still Ready for operation in a guild master

DC shunt motor, main spindle motor, servo motor, DC motor, DC motorSIEMENS type 1GG5134-0WH46-6HU7-ZNow power: 22.5 kWook voltage: 38 to 380 volts DCNenn current: 67 ADore number: 50 - 2160 / 4050/5000 rpmShaft diameter: mmShaft pin length: mmKeyway width in the shaft: mm- Foot motor with 4 mounting holes- with mounted external fanOverall dimension L x W x H: approx. 700 x 580 x 350 mmWeight: approx. 250 kgThe drive motor is still ready for operation in a Guild Master GDM42. The

Universal face and boring head LENZ type LPA 1SSpindle tool, spindle head similar to WOHLHAUPTER UPA3Tool holder: SK 40 - M16Adjustment accuracy: 0.01 mm- Accessories as shown- Storage boxWeight: approx. 5 kggood condition; used