sk 50 used for sale

; Power [PS]: 170; Gross weight [kg]: 11000; Engine: Battery System: LIFePO4; Accessories: Battery, Stahldach

; Gross weight [kg]: 4100; Engine: Volvo TAD1345GE; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 515

table length: 500 mm table width: 250 mm ampere: 50 A x-axis: 290 mm y-axis: 200 mm z-axis: 300 mm total power requirement: 6 kW weight of the machine ca.: 1100 kg dimensions of the machine ca.: m CNC-Controlled Die Sinker The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 500 t passage width: 750 mm stroke: 120 mm total power requirement: 57 kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Power: 7,5 KW Receiver: 500 L weight of the machine ca.: 300 kg dimensions of the machine ca.: 1,7x 0,6 x 1,45 m feed pressure: 16 bar liter capacity: 870 l The UWM 10/870/500 K50 + Startbox is equipped with a K50 pump. Note that this is a high-pressure version (especially for trucks or places where higher pressure is required), Industry and hard work. The starting box is used to obtain a lower starting voltage (around to reduce peak voltages. The UWM 10/870/500 is available with 400 V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping range of chuck: 200 - 500 mm height: 110 mm daylight: 240 mm external diameter: Futter 320 mm external diameter: Spannhebel 700 mm weight: 56 kg Characteristics: • Self-centering. • Reversible jaws. • Fixed clamping levers allow fast workpiece changes. • Low weight and flat design minimize the center of gravity. The D-D quick chuck enables a quick product change and is suitable excellent with frequent component changes. You do not need a loose one Quick release wrench, as the levers are integrated into the quick release chuck. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 1600 mm table width: 800 mm stroke height: 900 mm : 310 mm weight max. in kg: 500 kg weight of the machine ca.: 0,16 t : 1,7 x 0,82 x 0,33 m The mobile work and lifting table has an easy-to-use foot pedal to raise the table. You can safely lower the table again using the hand pedal. There are four rollers under the table. Two of them are equipped with brakes. The work table is equipped with a fall protection for additional safety. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40 mm throat: 350 mm bore stroke: 180 mm spindle taper MT: 4 MK table:: 560 x 560 mm column diameter: 140 mm turning speeds: 50 - 1450 U/min feeds: 0,1 - 0,2 mm/U total power requirement: 1,5 kW weight of the machine ca.: 580 kg range L-W-H: 2,27 x 0,7 x 1,1 mm • machine base for clamping high workpieces • Digital Depth Gauge • Gearbox swivels 180 ° • silent running through geärtete, ground oil-cooled gears • Tapping Function • electromagnetic clutch for drill feed • automatic feed • electric drive for table height adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 500 kN stroke: 40 mm throat: 73 mm Working height from to: 60 - 150 mm table surface area: 115 x 70 mm weight of the machine ca.: 10 Kg .Toggle lever hand press SPECIAL OFFER! • Working height adjustable by simply loosening the clamping screws on the stand • Working height fine adjustment for HK 800 = adjustment of the press head to the desired working height. The fine adjustment takes place forced in both directions via a threaded spindle • Hand lever arranged in a user-friendly manner, return via spring The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

used baler Manufacturer: PAAL Type: DOKON 500 with twine tying Year of construction: May 2014 Technical data: Binding: 5-fold horizontal Press weight up to: approx. 30 t Press force: 122 t Specific pressing force: 9.90 kg/cm² Filling opening: approx. 2,000 x 1,020 mm Channel cross-section: 1,100 x 1,100 mm Drive power: 1 x 45 kW Throughput: 250 m³/h Pressing services: at 100 kg/m³ bulk density: approx. 25 t/h at 150 kg/m³ bulk density: approx. 30 t/h at 200 kg/m³ bulk density: approx. 35 t/h Binding: 5-fold horizontal Transport dimensions: Length: 13,300 mm Width: 2,600 mm Height: 3,300 mm without yarn unwinding devices, without control cabinet, without binding twine, without feed belt, without a personal protection system, without conveyor belt hopper and without walking surface with vertical la ...

weight max. in kg: 1600 kg fork length: 1150 mm stroke height: 5000 mm high: 2185 mm weight of the machine ca.: 0,98 t dimensions: 1,72 x 0,8 x 2,2 m Pallet truck with - Triplex mast - Lithium-ion battery - quick lifting and lowering - low overall height The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Availability: as of now Machine dimensions (LxWxH): 0.8 x 0.8 x 2.0 m Weight: 150 kg Bottle drying system was operated without technical problems until 04.2026. The dismantling was then carried out by qualified personnel. Consisting of: - 1 Paxton high-performance centrifugal blower XT 500 4kW - 2 stainless steel heavy-duty air blades 580mm lg. - 2 stainless steel air blade holders for Adjustment in 3 levels - 1 stainless steel base frame with attached Blower - 1 stainless steel air distributor 2 x DN 76 mm - 1 soundproof enclosure for XT 500 blower - 4 stainless steel covers on all sides as Splash guard Additional equipment: - 1 pc. Geset stainless steel nozzle 40 x2 mm incl. piping and hose For lid blow-off before inkjet The Gesete XT 500 bottle drying machine was manufactured in 2014 and is designed for drying bottles in front of a labeling machine (Etima) ...

table load: 500 Kg table load capacity: 250 kg. vertikal table diameter: 550 mm swivelling range: 135 (-45 - +90) Grad turning speeds: 0 - 5 stufenlos U/min connected load frequency: 230 V total power requirement: 0,8 KW weight of the machine ca.: 0,255 t dimensions of the machine ca.: 0,82 x 0,73 x 0,71 m Welding turntable with - large passage 165mm - Footswitch - tilt by motor - Speed infinitely adjustable - 250 amp welding current transmission Demonstration machine documentation only in English. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 1170 x 580 x 580 mm operating pressure: 2,2 - 8,0 bar dimensions: 1,22 x 0,93 x 1,70 m air consumption at 6 bar: 350 l/min weight of the machine ca.: 0,15 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 690 mm table load: 0,5/0,25 t swivelling range: 0 - 90 motorisch Grad turning speeds: 0,2 - 2,5 U/min spindle bore: 100 mm Torque: 375 Nm welding current: 500 Ampere connected load frequency: 230 Volt weight: 290 kg Dimensions (LxWxH): 800 x 750 x 750 mm Welding turntable with - Footswitch - tilt motor - Speed continuously adjustable - 500 amps welding current transmission The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Crane bottle, crane hook, load hook, single hook, lower bottle, lifting bottle -Manufacturer: Demag, crane hook lower block -Load capacity: 500 kg -Hook opening: 32 mm -Dimensions: see photos -Dimensions: 240/90/60 mm -Weight: 1.7 kg

Tube cutting machine manufactured in 2015. This TRUMPF TruLaser Tube 5000 features a working range of 6500 mm in the X-axis and 310 mm in the Y-axis, with a maximum workpiece length of 3000 mm. It supports various tube diameters and has a maximum workpiece weight of 130 kg. If you are looking to get high-quality tube cutting capabilities, consider the TRUMPF TruLaser Tube 5000 machine we have for sale. Contact us for further details.

The DYNAJET 500th HELI Blue Performance is designed for professional users who need a high-performance, trailer-based high-pressure waterjet system for demanding industrial applications. With hot and cold water operation up to 500 bar and a maximum flow rate of 30 l/min, it is ideal for tasks such as surface preparation, paint and rust removal, concrete renovation and maritime maintenance. Its robust trailer design is designed for demanding daily operations and transport between job sites. The single-axis design supports easy maneuverability, while the integrated single-point lifting eye allows for efficient lifting and positioning when crane handling is required. The Targa design separates the motor, pump and burner area from the operator area, which supports safe and ergonomic operation while reducing noise pollution at the operator station. The colour display provides a clear ov ...

pressure: 500 t column daylight: 2600 mm stroke: 800 mm table surface area: 6000 x 3000 mm : max. 800 mm adjustment of press crosshead: 5200 mm slide adjustment -horizontal: 1800 mm Capacity: 162 l/min feed down: 9 mm/sec feed up: 14 mm/sec total power requirement: 45 kW weight of the machine ca.: 50 t - Hydraulics : Rexroth - Controls : Tailor - Cylinder chromed - Operation via remote control & joystick - Stroke length adjustable via sensors - Pressure adjustable via PLC The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 855 mm table width: 500 mm stroke height: 900 mm : 340 mm weight max. in kg: 500 kg weight of the machine ca.: 0,085 t : 950 x 550 x 450 mm The mobile work and lifting table has an easy-to-use foot pedal to raise the table. You can safely lower the table again using the hand pedal. There are four rollers under the table. Two of them are equipped with brakes. The work table is equipped with a fall protection for additional safety. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

measuring length: bis 5000 mm Tube length: 5280 mm numbers of toolholders: 6 : Rohr Edelstahl dimensions: 5,3 x 0,3 x 0,2 m The length measuring system is available for retrofitting existing roller conveyors in lengths from 2 to 6 meters. The running rail made of rectangular tube 60 x 30 x 3. The steel measuring tape is self-adhesive. The magnifying glass with 6x magnification makes it easier to adjust the settings precisely desired length. Danger: This is just the stop system without roller conveyor! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This 3-axis DAEWOO MYNX 500 was manufactured in 2000. It features an X-axis stroke of 1,020 mm, Y-axis stroke of 510 mm, and Z-axis stroke of 575 mm. The machine includes a table dimension of 1,200 x 500 mm and a spindle speed of 10,000 rpm. If you are looking to get high-quality machining capabilities, consider the DAEWOO MYNX 500 vertical machining centre we have for sale. Contact us for further details.

A stationary oil lubricated, belt driven reciprocating compressor from Mark with an air receiver is offered. Motor power: 7.5kW (10hp), intake capacity: 1300l/min, max. operating pressure: 10bar, air receiver volume: 500l, compressed air connection: G 1/2. Dimensions X/Y/Z: approx. 1910mm/600mm/1230mm, weight: approx. 330kg. Inspection possible by prior arrangement.

A Daiß + Partner CNC automatic band saw with a double-miter twin-column design is offered. Cutting capacity X/Y: 500mm/320mm, saw blade dimensions: 4700mm/34mm/1.1mm, feed length: 2000mm, rapid traverse: approx. 12m/min, blade speed: 15-105m/min, CNC control: PS 210. Equipment: powered chip brush, Power-Box hydraulic cutting pressure adjustment, Micro-Cooler coolant spray system, hydraulic saw blade tensioning and saw blade breakage monitoring. An on-site inspection is possible.

table diameter: 550 mm table load: 500 Kg swivelling range: 135 Grad tilt adjustment: manually/mechanicall: motorisch turning speeds: max. 5 U/min stufenlos table load capacity: 250 kg. vertikal total power requirement: 0,8 kW weight of the machine ca.: 245 Kg dimensions of the machine ca.: 820 x 730 x 710 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

impact length: 5000 mm Weight of Material maxium: 300 Kg/m Wheel width: 350 mm roll diameter: 60 mm work height adjustable: 840 - 950 mm weight: 172 kg length in width: 620 mm length in total: 5400 mm Roller conveyors including stop system. Stable execution. are available from 2 to 6 meters in length. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The steam boiler plant was put into operation in February 1992 and has been running smoothly for the entire service life since then. The steam boiler has a capacity of NW 7170 ltr and is operated with a maximum operating overpressure of 10 bar. It can run on oil and gas. The steam boiler was regularly serviced and inspected by the TÜV. The last TÜV inspection took place in 2018 without any complaints. The steam boiler has been filled with treated water since its decommissioning in 2019 and can be dismantled and transported away immediately. The closure took place due to a plant closure. The complete documentation is available in the original. Further information, including price, can be requested by calling 0345 6868-0 or infonovachem

Roller conveyor length: 5000 mm Weight of Material maxium: 300 Kg/m Wheel width: 350 mm roll diameter: 60 mm work height adjustable: 840 - 950 mm weight: 140 kg length in width: 620 mm length in total: 5000 mm Roller conveyors without stop system. Stable execution. are available from 2 to 6 meters in length. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

FRYER, TS TECHNIEK BV, MODEL: HOF-5000x600 Technical description: Serial number: 200939-00124 Power supply: 400 V, 3 Ph, 50 Hz, 3 kW Mesh widht: 600 mm - (Stainless steel) Dimensions: 5000 x 1800 x 2300 mm With internal heating coil

; Gross weight [kg]: 2924; Engine: Caterpillar C13; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 721

Three burners are available. 1) Elco. 2) Seibold WV 500, year of construction: 2022, fuel: light oil EL, calorific value: approx. 10kWh/l, fuel flow rate: approx. 160l/h, nominal heat output: 1600kW, pilot burner fuel: propane, propane calorific value: approx. 26kWh/nm³, propane pre-pressure: 100mbar, max. chamber temperature: 270°C, max. chamber pressure: 3mbar. 3) Weishaupt, year of construction: 1999, output range: 474kW-2491kW. On-site inspection is possible.

; Gross weight [kg]: 690

turning diameter over bed: 400 mm turning diameter over slide rest: - mm turning length: 1000 mm total power requirement: 9 kW weight of the machine ca.: 2 t dimensions of the machine ca.: 2,51,21,6 m Machine has been partially overhauled Among other things engine renewed ( 8.000 EUR ) The repair was not completed due to plant closure The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

diameter: 0 mm workpiece length: 0 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Crack testing device for large series of workpieces The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 500 mm throat: 485 mm workpiece height: mm total power requirement: 2 kW weight of the machine ca.: 1 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 5000 kN

Offer(4x): Engel Duo 1800/500 BJ./YEAR 2016 38500h

: 24000 kg length: 5000 mm width: 2500 mm loading area height: 700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Clamping bracket, T-slot plate, clamping table, clamping cube, clamping plate, clamping tower, clamping box -Clamping cube: heavy version -Material: Cast iron -Dimensions: see photos / technical drawing -Quantity: 1x mounting cube available -Dimensions: 500/300/H300 mm -Weight: 89.7 kg

Suitable for measuring all types of milling and drilling tools, profiles, punching tools, drive and cardan shafts, profile rollers, etc. Accessories: Measuring table adjustment with digital display, Screen diameter: 500 mm, Enlargement: 50 and 100 times, Swivel range of the upper table: +/- 2 mm, Connected load approx.: 230 V / 50 Hz, Dimensions W x D x H approx.: 1200 x 700 x 1800 mm, Weight approx.: 400 kg, colour: Light grey

We offer a highly productive 3D printer for industrial series production The system was finally used with aluminum powder AISi10MG The 3D printer has already been dismantled by the manufacturer Disassembly logs are available as well as functional logs that prove that the machine was in operation before dismantling All axles are professionally secured The machine can be transported on a normal standard truck TruPrint 5000 G4 Serial Number S0731C0008 Year of construction 08/2018 Time-of-Flight Laser Laser 1 Beam on On: 5165 hrs Laser 2 Beam on On: 5096 hrs Laser 3 Beam on on: 5023 hrs Trumpf TruPrint 5000 with Powder Bed Monitoring and Melt Poll Monotoring options included Filter system Accessories: 2pcs. Build Cylinder 3pcs. Dosing cylinder 1 pc. overflow tank used 1 Pc. Overflow Tank NEW Manuals 4 Heat Exchangers NEW 2 pcs Easy Filter NEW 3 pcs NTRON SIL ...

This 5-axis Mazak VARIAXIS I 500 was manufactured in 2006. It features an X-axis travel of 510 mm, Y-axis travel of 510 mm, and Z-axis travel of 460 mm. The machine includes a tool magazine capacity of 60 tools and a maximum spindle speed of 12,000 rpm. If you are looking to get high-quality milling capabilities, consider the Mazak VARIAXIS I 500 vertical machining centre we have for sale. Contact us for further details.

A small Alfred Reith bench punch is available. Punching force: 50kN, max. round hole diameter: 60mm, max. square hole dimensions X/Y: 46mm/46mm, max. mild steel sheet thickness: 3mm, max. stainless steel sheet thickness: 2mm, max. aluminum thickness: 4mm, throat depth: 500mm, stroke: 66mm, weight: approx. 200kg. Documentation available. An on-site inspection is possible.

weight max. in kg: 5.500 kg stroke: - mm fork length: - mm weight: ca. 7.400–7.600 kg (je na kg drive: GAS The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 630 mm, 620 mm, 710 mm

ÖKK HP 500S CNC Horizontal Machining Center CNC Control Fanuc 160is-MB Pallet table size 500 x 500 mm Number of pallets 2x Table load 400 kg X-axis travel: 630 mm Y-axis travel: 620 mm Travel Z-axis: 710 mm Table Indexing 0.001° Spindle Heads MAS BBT40 Spindle speed 100 - 12,000 1/min Spindle drive 11/7.5 kW Number in Stacks: 60 If you have any questions about the machine, as well as an appointment for a viewing, please contact us by phone or e-mail. Feel free to check out our other ads for a full overview of our stock. We are selling this machine at a special price, called "as seen". This means that we do not check the condition of the machine.

Double-Belt weighing system for large volumes of 1-50kg of loose materials as bio-pharmaceuticals, food, farm chemical and fertilizer, building materials, ceramcis, chemicals, drug ingredients, seeds, cereals, charcoal, flow soil, plastic grains, etc. - Specifications: 65 liter hopper | all product contacting parts in stainless steel (SS340) | frame in mild steel with painted surface | Accuracy (depending on product): 0,5-1,0% | pre-Set-Option for 10 programs | max. speed of the machine in neutral: 15 cycles/minute. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available  ...

Very large linear weigher for high volume weighing with 2 heads. - Specifications: weighing range: 5-50kg | max. speed of the machine in neutral: 20 cycles/minute | accuracy: 0.2% (depending on product) | power: 2.0kW | machine dimensions: L3300xW3000xH4700mm (including 1400mm standing frame/can be customized) | weight: 1800kg. That machine/system is available in different versions for different packaging sizes and with different packaging speeds. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.

Fully automatic powder filling system, triple auger-filler unit, straight transport of cans. Functions: automatic container feeding - precision positioning - container lifting - vibration - filling - weighing feedback - sorting - container outfeed. PLC control, precision servo system, dosing technique: screw and load cell feedback, removable glass cover. With Wi-Fi function, remote control and data download system. Easy cleaning, movable conveying platform and recycle funnel. SIEMENS PLC, SCHNEIDER Servo Motor, SCHNEIDER Inverter, AIRTAC pnematics, HBM weighing sensor (Germany). 2 packaging modes: High speed or High Accuracy. Specifications: stainless steel (SS304) version | filling range: 10-500g | accuracy: +/- 0.3-1% (high speed mode), +/-1-2g (high accuracy mode) | suitable for: metal cans, glass bottles, plastic jar, cardboard cups, etc. | container dimensions: diameter 40-130, heig ...

Fully automatic powder filling system, double auger-filler unit, straight transport of cans. Functions: automatic container feeding - precision positioning - container lifting - vibration - filling - weighing feedback - sorting - container outfeed. PLC control, precision servo system, dosing technique: screw and load cell feedback, removable glass cover. With Wi-Fi function, remote control and data download system. Easy cleaning, movable conveying platform and recycle funnel. SIEMENS PLC, SCHNEIDER Servo Motor, SCHNEIDER Inverter, AIRTAC pneumatics, HBM weighing sensor (Germany). 2 packaging modes: High Speed or High Accuracy | - Specifications: stainless steel (SS304) version | filling range: 10-5000g, accuracy: +/- 0.3-1% (high speed mode), +/- 1-2g (high accuracy mode) | suitable for: metal cans, glass bottles, plastic jar, cardboard cups, etc. | container dimensions: diameter 50-200, ...

Basic Automatic Linear Auger Filler with weight feedback via separate weigher. Including free flow device for better product flow control and including dustproof cover. SIEMENS PLC controlled with SIEMENS Touch Screen. - Specifications: Hopper volume: 45 liter | filling weight: 10-5.000g | stainless steel version with servo motor | packing accuracy: 0-2% (at 0-100g), 0-1% (at 100-550g), 0-0.5% (at 500g and more) (depending on product and total weight) | max. speed of the machine in neutral: 40 cycles/minute | power: 380V, 1.6kW | compressed air: 0.05m?/min, 6bar | machine dimensions: L2000xW1000xH2100mm | weight: 200kg. That machine/system is available in different versions for different packaging sizes and with different packaging speeds. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 di ...