single used for sale

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Single sided edge bander with hot melt, fixed side at the right, pre-milling unit Edge thickness: 0,4 to 12 mm Workpiece thickness: 8 - 60 mm Feedspeed 8-20 m/min (limited to 10 m/min using the contour trimming) Workpiece transport by chain, top pressures with rubber rollers Sound enclosure over all trimming motors Equipment: Adjustable fence Pre-milling with 2 shapers, each 2,2 kW Coil and strip magazine Hot melt unit, Quickmelt type Pressure zone with1 driven and 2 non-driven pneum. Loaded rollers End trims, 2 x 0,35 kW motors, straight and chamfer 15° Top/bottom trimming, motors 2 x 0,35 kW Radius trimmming Contour trimming unit, leading and following edge, 2 x 0,35 kW Radius scraping unit Glue scrapers Buffing unit Controlls PC 20+

Workpiece thickness: 8 - 90 mm, electronically adjustable Feed rate: 18-32 m/min frequency controlled Edge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mm Equipment: Inlet guide automatically adjustable via the control, extension 500 mm Joint milling unit: 2 x 3.0 KW workpiece preheating Gluing unit A34 edging magazine for roll Pressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the control Cutting unit WK14, straight, 2 motors 0.8 kW Pre-milling unit: 2 x 1.5 KW, pneumatic adjustment Form milling unit FF 12 automatic, 2 motors 0.4 kW radius/phase milling unit FF12 automatic 4 motors 0.4 KW universal milling aggregate controlled UF11, 4 kW Profile scrapers PN20 Glue scrapers Nozzles for detergent and anti-stick Polishing unit Control: Power Control PC22

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Right-hand version Workpiece dimensions: max. length 3000 mm, min. 250 mm, max. thickness 100 mm, min. 30 mm, width 200 mm Overhead cutting saw, 3 kW, 3000 rpm, manual horizontal movement over 120 mm, 400 mm blade, cutting height 100 mm 1 vertical shaft, 340 mm long, 40 mm diameter, 7.5 kW, 3100 rpm, suction port with 150 mm diameter (x2), max. tool diameter: 320 mm Carriage with pneumatic clamping 1100 x 500 mm table Stop, positioning from -45° to 45° Motorized carriage with electronic control 2-32 m/min

Offered are two Weingarten single-column eccentric presses. 1) Weingarten AR 125 single-column eccentric press, delivered: 1970, pressing force: 125t, max. sheet thickness: 13mm, stroke rate: 44/66strokes/min, ram stroke: 20-120mm, ram adjustment: 100mm. 2) Weingarten AR 125 single-column eccentric press, delivered: 1974, pressing force: 125t, stroke rate: 42/62strokes/min, ram stroke: 20-120mm, ram adjustment: 100mm. Inspection possible by arrangement.

Thermo Scientific ClipTip F1 12-Channel Micropipette | 30 - 300 PIPETMAN single-channel micropipette | 1 - 10 Auction-ID: A1-51251-104

Rated force: 125t, stroke adjustment: 20-140mm, ram adjustment: 80mm, stroke rate: 50/min, motor power: 10HP, drive: mechanical eccentric drive, machine is fully functional, maintenance, repairs and safety inspections have been carried out regularly, inspection logbooks and inspection reports are available for the period 2010-2025, extensive maintenance and repair work has been carried out in recent years, including work on the connecting rod and connecting rod bearing, eccentric bushing, bearing points, gear coupling, brake and clutch shoes, bearings, bushings, lubrication system, lubrication pump, parallel keys and other components. On-site inspection is possible.

Single piece loading dimensions: 200 x 240 x 120 mm Auction-ID: A7-51355-1332

Professional HDR LUX heavy-duty industrial pallet racking system. Configuration: single row. 14 pallet racking bays. Approximate overall length: 39.40 m. Bay width: 2,700 mm. Upright frame height: 10,000 mm. Upright frame depth: 1,100 mm. Storage configuration: floor storage + 4 beam levels. Beam dimensions: approximately 2,700 x 130 x 50 x 1.4 mm. Reference beam level load capacity according to manufacturer documentation: 3,000 kg per level. Heavy-duty steel construction. Modular and dismantlable pallet racking system designed for professional warehouse, logistics and industrial storage applications. The racking is currently dismantled and ready for collection. The lot is offered as one complete single-row pallet racking configuration. Images shown are reference images from other installations completed by HDR LUX and are provided for illustrative purposes only. Loading,  ...

Professional HDR LUX heavy-duty industrial pallet racking system. Configuration: single row. 14 pallet racking bays. Approximate overall length: 39.40 m. Bay width: 2,700 mm. Upright frame height: 10,000 mm. Upright frame depth: 1,100 mm. Storage configuration: floor storage + 4 beam levels. Beam dimensions: approximately 2,700 x 130 x 50 x 1.4 mm. Reference beam level load capacity according to manufacturer documentation: 3,000 kg per level. Heavy-duty steel construction. Modular and dismantlable pallet racking system designed for professional warehouse, logistics and industrial storage applications. The racking is currently dismantled and ready for collection. The lot is offered as one complete single-row pallet racking configuration. Images shown are reference images from other installations completed by HDR LUX and are provided for illustrative purposes only. Loading,  ...

Offer 26180 Technical data: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Installation height approx. 1000 mm - Projection to the middle of the ram 520 mm - Pusher clamping surface 350 x 350 mm - Plunger clamping pin 40 mm - Table size 1000 x 1150 mm - Table opening 150 x 780 mm - Table height above floor 720 mm - Drive 400 V / 8 kW - Space requirement approx. W 1150 x H 2900 x D 2150 mm - Weight approx. 4800 kg

Single piece loading dimensions: 200 x 240 x 120 mm Auction-ID: A7-51355-17

Single piece loading dimensions: 200 x 240 x 120 mm Auction-ID: A7-51355-1334

Single piece loading dimensions: 200 x 240 x 120 mm Auction-ID: A7-51355-1335

Single piece loading dimensions: 200 x 240 x 120 mm Auction-ID: A7-51355-1333

Auction-ID: A1-51285-273

Very clean unbraked single-axle box trailer of 2m by 1.1 m / just new tyres and rims, the spare wheel is also new / working lighting / ready for immediate use Auction-ID: A3-46109-6513

Screw ø 75-36D; approx. 660 kg/h Co Extruder Year 2015

Key data: 65 mm

Starlinger single-screw extruder recoStar 65 Technical data and equipment: - Screw diameter: 65 mm - Machine overhauled - Degassing zones - Filter / screen changer - String nozzle installed - Data sheet see photos Optionally available with water bath, strand granulator and other accessories. Commissioning and testing possible by arrangement. Immediately available.

261 Layher Blitz Single Scaffolding Handrails – 2,007/2,570 mm – including stacking rack Specifications: Brand: Layher System: Blitz / SpeedyScaf Type: Single Scaffolding Handrail/Handrail Rail Quantity: 261 pieces 81 pieces with a length of approx. 2,007 mm 180 pieces with a length of approx. 2,570 mm Material: galvanized steel Design: round tubular steel construction Features: Fixed connection/hook ends Boltless system mounting Version for use as horizontal railing/edge protection within the respective Layher scaffolding system Various original markings and markings for use Includes the stacking/transport rack shown with this lot Stacking rack suitable for storage and transport of the scaffolding parts Particularities: Used condition with normal signs of use, paint, weather and storage Bundled and stored for efficient transport Forklift available to load t ...

Heavy Single-Axle Agricultural Dolly – ROR Axle – Fifth Wheel – 385/65 R22.5 Heavy-duty single-axle agricultural dolly for coupling a truck trailer to an agricultural tractor. Robust steel version with ROR axle, drum brakes and fifth wheel. Suitable for moving and transporting suitable trailers behind an agricultural tractor. Specifications: Type: Agricultural Dolly/Semi-trailer Dolly Version: single axle Axle brand: ROR Tyre Size: 385/65 R22.5 Tyre profile: approx. 4 mm Fifth wheel height: approx. 1,100 mm Features: Drum brakes Wide ankle mount Steel rims Fifth wheel Heavy draw/drawbar construction Heavy Welded Steel Chassis Compact and robust agricultural design Suitable for standard truck trailers Suitable for use behind a suitable agricultural tractor Can be used for tipper, walking floor, container and other suitable trailers , among others Part ...

• Optical technology: Single-beam equipped with tungsten and deuterium lamps with a silicon photodiode detector. • Display and interface: Touchscreen (often 7 inches on Smart versions such as the OPTIZEN POP-V) under Windows CE operating system or integrated software with voice guidance. • Measurement modes: • Photometric: Absorbance / % transmittance (%T) at fixed wavelengths. • Quantitation: Multipoint calibration curves (linear, quadratic, cubic, etc.). • Spectrum: Wavelength scanning and peak/valley analysis. • Kinetics: Tracking absorption or transmittance over time (from 1 second to 24 hours). • Technical specifications (POP-V model): • Wavelength range: 340 to 1100 nm (or depending on the exact configuration of the model). • Photometric range: -3A to 3A. • Sample holder: Often equipped with a multi-cell automatic changer (up to 8 positions de ...

• 22 kW, 400 V / 50 Hz, 55 A • Approx. 2.4 tonnes • Serial no. H 11/13/151 • Large flared feed hopper • Pneumatic discharge • Standalone control cabinet with isolator • CE marked • Fully working – can be seen running • Buyer collects – loading provided at our Wymeswold site, Leicestershire A 2014 Gross GAZ 102 single shaft shredder. Single shaft shredders use a slow-turning rotor and a hydraulic pusher to break down bulky, awkward plastic such as purgings, lumps, pipe, crates and thick-walled mouldings, producing a size that a granulator or wash line can then handle. The large flared hopper makes it easy to load by hand or from a tipping bin, and pneumatic discharge carries the shredded material away from the machine. We run balers, granulators and shredders on our own site at Wymeswold, near Loughborough, so we can talk you through how a machine like  ...

- Ford Transit Flatbed, Single Cab - Registration date: 24.10.2013 - 2.2 l TDCi diesel engine with 92kW (125hp) - Manual transmission - Mileage: 171,593 km (read) - Permissible total weight: 3,500 kg - Orange municipal version - Aluminium flatbed with foldable tail lifts - Trailer hitch available - Rotating beacons available and functional - Protective grille available behind the driver's cab - Vehicle shows signs of wear due to age and mileage - Engine compartment complete, no obvious missing parts recognizable - Tail lifts in good condition with slight scratches and signs of wear - Loading area with clear signs of wear - Interior slightly worn and used according to age - Hood faded - Rust at the entrance of the driver's side - Slight rust formation at the entrance of the passenger side - Rust on both wheel arches - Rust on the lower door area - Traces of rust on the veh ...

Set of 42 Proact Single-Use Metal Laryngoscope Blades, Never Used Manufacturer: Proact Quantity: 42 Condition: New, Never Used Auction-ID: A1-51618-260

Transport trailer designed for the safe transport of a wide range of loads. Thanks to the 40 cm high side boards and the folding front and rear boards, loading and unloading is quick and easy. The welded construction guarantees high durability, while the tilting drawbar increases user comfort. Bumpers on the rear frame ensure that the trailer can be placed stably on the rear board, so that it takes up only minimal space during storage. By removing the side boards, the trailer can easily be transformed into a transport platform, increasing versatility. Optional equipment includes double side boards, mesh side boards, a flat tarpaulin and a canopy frame. Auction-ID: A3-46113-17646

faceplate diameter:1400 mm swing diameter:2000 mm turning height:1500 mm main drive:80 kW faceplate speeds from - to:1 - 365 U/min milling motor:37 kW ram head dimension:240 x 240 mm max. ram stroke:1250 mm total power requirement:133 kVA weight of the machine ca.:50 t dimensions of the machine ca.:11 x 5 x 6,4 m Machine was overhauled in 2008 by OEM New control CNC SIEMENS 840 D automatic tool changer 72-pcs C-axis with driven tools Angle-, straight tool holders with CAPTO holder Coolant device Chipconveyour

pressure:40 t throat:220 mm stroke:8 / 88 mm table pass:ø- abgesetzt 225/200 mm ram head dimension:400 x 250 mm distance table/ram:228 mm stroke adjustable from - to:30 - 140 mm ram adjustment:63 mm thickness of bolster:80 mm no. of strokes:70 Hub/min total power requirement:5,5 kW weight of the machine ca.:2600 kg dimensions of the machine ca.:1100 x 1300 x 2300 mm Documents:vorhanden

faceplate diameter:1800 mm swing diameter:2000 mm turning height:1170 mm z-axis:1000 mm cross rail adjustment - vertical:800 mm faceplate speeds::2,5 - 280 workpiece weight:12 t feeds:1 - 6000 mm/min max. torque on the faceplate:50000 Nm total power requirement:85 kW weight of the machine ca.:41 t dimensions of the machine ca.:5,6 x 4,8 x 4,6 m Machine retrofit and overhould in 2005 with SIEMENS 840 D powerline control - 6 jaw hydraulic power chuck - tool changer for 12 tools - chip conveyor, coolant attachment, splash housing - various tool holders

faceplate diameter:1000 mm swing diameter:1600 mm turning height:1200 mm main drive:75 kW faceplate speeds from - to:7 - 800 U/min milling motor:25 kW milling head speed:7 - 3000 U/min milling spindle - taper:ISO 50 cross rail adjustment - vertical:800 mm ram head dimension:240 x 240 mm weight of the machine ca.:40 to dimensions of the machine ca.:9 x 7,8 x 6,0 m Machine general overhould in 2004 and equiped with Siemens 840 D control - tool changer rack magazine - C-axis, live tooling, - Transmit function electronical Y-axis - angular milling head - complete splash housing - coolant device, chip conveyor

faceplate diameter:1400 mm swing diameter:2000 mm turning height:1270 mm main drive:80 kW faceplate speeds from - to:1 - 355 U/min max. workpiece weight:6.000 kg milling motor:37 kW milling head speed:7 - 3000 U/min milling spindle - taper:ISO 50 cross rail adjustment - vertical:800 (8 x 100 mm) mm ram head dimension:240 x 240 mm max. ram stroke:1250 mm weight of the machine ca.:50 to total power requirement:133 kVA dimensions of the machine ca.:11 x 5 x 6,4 m Machine general overhould in 2008 and equiped with CNC SIEMENS 840 D control - tool changer for 72 tools - C-axis, live tooling - angular- and straight tool holder head with CAPTO taper - Transmit function - complete splash housing - coolant device, chip conveyor - diverse accessories

faceplate diameter:1600 mm swing diameter:1800 mm turning height:1500 mm max. ram stroke:1200 mm faceplate turning speed range -stepless-:2,5 - 250 U/min workpiece weight max.:10.000 kg ram head dimension:240 x 240 mm feed range:1 - 3000 mm/min power capacity:45 kW weight of the machine ca.:20 t modernized and overhauled in 2010 with CNC SIEMENS 840 D 12 positions automatic toolchanger telescopic covers splash guarding chip conveyor coolant attachment diverse toolholders

faceplate diameter:1400 mm swing diameter:1470 mm turning height:1325 mm ram stroke range:750 mm adjustment of cross-rail:850 mm max. workpiece weight:12000 kg faceplate turning speed range:4,5 - 224 U/min feed per revolution:0,06 - 8 mm rapid speed:1,8 m/min total power requirement:50 kW weight of the machine ca.:16 t Machine was modernized in 2008 with new electric 2-axes digital readout 5-station turret head autom. swivelling diverse toolholders

pressure:063 t throat:250 mm stroke:8 - 100 mm no. of strokes:56 / 84 /min distance table/ram, max. stroke up, adjustment up:415 mm table surface area:710 x 500 mm hole in the table:320 mm table height over floor:800 mm passage to the back:320 mm ram surface:450 x 280 mm ram adjustment:63 mm weight:4,1 t dimensions (W x D x H):1,35 x 2,0 x 2,6 m overload protection in ram:mechanical

Pressure:080 t throat:380 mm stroke:8 - 112 mm no. of strokes:60 /min distance table/ram, max. stroke up, adjustment up:472 mm table surface area:840 x 610 mm table height over floor:800 mm passage to the back:520 mm ram surface:650 x 400 mm ram adjustment:70 mm power capacity:7,5 kW weight:6,9 t Dimensions (WxDxH):1,1 x 2,15 x 3,2 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 overload protection in ram:mechanical ram counterbalance:pneumatic clutch-/ brake combination:pneumatic

Pressure:063 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 /min distance table/ram, max. stroke up, adjustment up:415 mm table surface area:700 x 500 mm hole in the table:250 mm table height over floor:800 mm passage to the back:320 mm ram surface:450 x 280 mm ram adjustment:63 mm weight:4,5 t Dimensions (WxDxH):1,6 x 2,0 x 2,8 m overload protection in ram:mechanical

Pressure:063 t throat:250 mm stroke:10 - 100 mm no. of strokes:120 /min distance table/ram, max. stroke up, adjustment up:380 mm table surface area:700 x 500 mm hole in the table:180 x 140 mm table height over floor:700 mm ram surface:360 x 275 mm ram adjustment:60 mm power requirement:5,5 kW weight:3,8 t Dimensions (WxDxH):1,9 x 1,7 x 2,4 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch-/ brake combination:hydraulic overload protection in ram:mechanical

pressure:150 t throat:400 mm stroke:30 - 150 mm no. of strokes:50 /min distance table/ram, max. stroke up, adjustment up:620 mm table surface area:1000 x 750 mm hole in the table:320 x 200 mm table height over floor:800 mm ram surface:800 x 600 mm ram adjustment:85 mm weight:10,0 t Dimensions (WxDxH):1,4 x 2,2 x 3,1 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatic ram counterbalance:pneumatic

pressure:250 t throat:450 mm stroke:36 - 126 mm no. of strokes:40 /min distance table/ram, max. stroke up, adjustment up:525 mm table surface area:1000 x 750 mm hole in the table:400 x 360 mm table height over floor:1000 mm ram surface:600 x 500 mm ram adjustment:111 mm power requirement:19,0 kW weight:13,5 t Dimensions (WxDxH):1,3 x 3,2 x 3,35 m clutch:pneumatic overload protection in ram:mechanical ram adjustment:motoric

Pressure:250 t throat:450 mm stroke:8 - 135 mm no. of strokes:50 /min distance table/ram, max. stroke up, adjustment up:635 mm table surface area:1250 x 850 mm hole in the table:355 mm table height over floor:950 mm passage to the back:660 mm ram surface:790 x 610 mm ram adjustment:120 mm power requirement:18,5 kW weight:14,0 t Dimensions (WxDxH):1,5 x 2,8 x 3,65 m German Safety: permitted for manual loading:CE-Norm - EN 692, BGR 500 clutch:pneumatisch overload protection in ram:mechanisch ram counterbalance:pneumatisch

pressure:150 t throat:450 mm stroke:115 fix mm no. of strokes:45 /min distance table/ram, max. stroke up, adjustment up:400 mm table surface area:2250 x 1090 mm table height over floor:900 mm passage to the back:1900 mm ram surface:1900 x 900 mm ram adjustment:100 mm power requirement:16,0 kW weight:19,5 t Dimensions (WxDxH):3,0 x 2,3 x 3,9 m

pressure:015 t throat:200 mm stroke:4 - 70 mm no. of strokes:140 /min distance table/ram, max. stroke up, adjustment up:310 mm table surface area:430 x 395 mm hole in the table:165 x 160 mm table height over floor:560 - 735 mm table adjustable:175 mm ram surface:160 x 130 mm ram adjustment:80 mm power requirement:1,2 kW weight:0,9 t Dimensions (WxDxH):1,0 x 1,25 x 1,8 m clutch:Drehkeil overload protection in ram:mechanical

pressure:100 t throat:350 mm stroke:6 - 100 mm no. of strokes:60 /min distance table/ram, max. stroke up, adjustment up:400 mm table surface area:850 x 700 mm hole in the table:470 x 150 mm table height over floor:855 mm ram surface:450 x 300 mm ram adjustment:80 mm power requirement:7,5 kW weight:5,0 t dimensions (WxDxH):1,5 x 2,3 x 2,6 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatic overload protection in ram:mechanical

pressure:035 t throat:225 mm stroke:8 - 100 mm no. of strokes:110 /min distance table/ram, max. stroke up, adjustment up:400 mm table surface area:580 x 460 mm hole in the table:250 x 150 mm table height over floor:700 mm table adjustable:230 mm ram surface:355 x 120 mm ram adjustment:70 mm power requirement:2,2 kW weight:1,5 t dimensions (WxDxH):1,0 x 1,5 x 2,05 m clutch:rolling key overload protection in ram:mechanical

pressure:080 t throat:360 mm stroke:8 - 112 mm no. of strokes:78 /min distance table/ram, max. stroke up, adjustment up:467 mm table surface area:900 x 650 mm hole in the table:250 mm table height over floor:800 mm passage to the back:330 mm ram surface:650 x 400 mm ram adjustment:80 mm power requirement:11,0 kW dimensions (WxDxH):1,2 x 2,2 x 2,9 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 overload protection in ram:mechanisch

pressure:063 t throat:450 mm stroke:8 - 100 mm no. of strokes:65 /min distance table/ram, max. stroke up, adjustment up:415 mm table surface area:720 x 800 mm hole in the table:280/250 mm table height over floor:800 mm passage to the back:290 mm ram surface:450 x 280 mm ram adjustment:63 mm power requirement:7,5 kW weight:4,7 t dimensions (WxDxH):1,3 x 2,0 x 2,65 m clutch:pneumatisch overload protection in ram:mechanisch

Pressure:063 t throat:400 mm stroke:16 - 90 mm no. of strokes:60 /min distance table/ram, max. stroke up, adjustment up:350 mm table surface area:1000 x 750 mm hole in the table:260 x 140 mm table height over floor:710 mm ram surface:600 x 220 mm ram adjustment:50 mm weight:4,3 t dimensions (WxDxH):1,1 x 2,6 x 2,4 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatisch overload protection in ram:mechanisch ram counterbalance:pneumatisch

pressure:050 t throat:255 mm stroke:8 - 120 mm no. of strokes:115 /min distance table/ram, max. stroke up, adjustment up:380 mm table surface area:640 x 500 mm hole in the table:250 x 180 mm table height over floor:710 - 930 mm table adjustable:220 mm ram surface:550 x 170 mm ram adjustment:70 mm power requirement:4,0 kW weight:3,1 t dimensions (WxDxH):1,5 x 1,5 x 2,3 m

pressure:050 t throat:250 mm stroke:8 - 120 mm no. of strokes:100 /min distance table/ram, max. stroke up, adjustment up:400 mm table surface area:650 x 515 mm hole in the table:115 mm table height over floor:790 - 1020 mm table adjustable:230 mm ram surface:390 x 180 mm ram adjustment:70 mm power requirement:2,0 kW weight:2,6 t dimensions (WxDxH):1,1 x 1,4 x 2,2 m overload protection in ram:mechanical