single used for sale

Single column - eccentric press WEINGARTEN type ER 63Masch. No. 52A / 63 Year of construction 1963Pressure capacity 63 ton. Projection 280 mmTable surface 630 x 530 mmAdjustable plunger stroke 8-100 mmPlunger adjustment 63 mmStroke rate 65 strokes / min. Engine power 4 kWNetz connection 380 Volt, 50 Hz- Clutch-brake combination by WEINGARTEN friction threaded clutch- Electrical stroke release via foot switch- Wheel counters- Overload protection by crushing plate- Front crankshafts Support bearingSpace requirement L x W x H 1500

Single column - eccentric press PELS - RICHTER type PEKR 125Masch. No. 20684 Year of construction 1967Compressive force 125 ton. Projection 430 mmTable size 1100 x 750 mmPlunger area 890 x 650 mmTable opening 400 mmStroke adjustment 6 to 115 mmRam adjustment 100 mmInstallation height largest stroke top max. 450 mmClamping pin bore 50 mmStroke rate 60 strokes/min. Table height above floor 900 mmMotor power 7.5 kWNerg connection 380 volts, 50 Hz- overload protection by crushing plate in the plunger- compressed air

Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil

Single column hydraulic press SCHULZ type SES 250Masch.Nr. 04.86.3511/3 Year of manufacture 1986Compressive force 25 ton. Retraction force 10 toProjection 360 mmTable surface 600 x 720 mmPlunger area 500 x 500 mmFailure opening in table 100 mmPin hole 40 mmPlunger stroke 400 mmInstallation height max. 600 mmTable height above floor 935 / 775 mmTank capacity hydraulics 380 litresDrive power 7.5 kWNet connection 380 volts, 50 Hz- Fixed stop adjustment in the press cylinder 180 mm- Light barrier

Z640 Mixed Lot (134 pieces) Feed Pliers Automatic Lathe Lathe Turning Center probably for Index Traub or Schütte or similar machines

Single-column eccentric press MÜLLER GEFREES type PDET 5 S/EKMasch. No. Year of manufacture 1988Compressive force 5 ton. Projection 125 mmColumn passage 170 mm Table surface 280 x 220 mmWaste height 90mmLifting area 160 x 100 mmLifting adjustment 4 to 40 mmRam adjustment 30 mmInstallation height largest stroke at the top max. 210 mmStroke rate 200 strokes/min. Clamping pin bore 25 mmTable height above floor 900 mmEngine power 0.55 kWNerg connection 380 volts, 50 Hz- pneumatic clutch-brake combination-

CINCINNATI PROTON 45-30G Attention: Machine in left-hand version Screw diameter: 45 mm, L/D = 30 Grooved catchment zone Motor (DC drive): 65 kW Screw speed: max. 320 rpm Tool zones: 4+1 for adapters Melt pressure & temperature sensor included EXcPRO-NT control incl. CAN bus for data communication Air conditioner for control cabinet Cylinder in bimetal design – condition: very good Screw with few operating hours – condition: very good Without material funnel & without adapter

Inv. Num. : 8601 Type: DV 40 W Producer: HAMM Generated: Parameters: Speed: 12 km/h Cylinder width: 1200 mm Length: 3310 mm Height: 2610 mm Width: 1425 mm Machine weight: 4100 kg

pressure: 20 t throat: 200 mm stroke: 0 - 50 mm table:: 360 x 550 mm table:: 140 mm - Bohrung no. of strokes: 160 Hub/min bore: 35,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 240 mm total power requirement: 2,2 kW weight: 1.250 kg range L-W-H: 1310 x 1250 x 1860 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 30 t throat: 200 mm stroke: 0 - 60 mm table:: 400 x 600 mm table:: 150 mm - Bohrung no. of strokes: 140 Hub/min bore: 40,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 300 mm total power requirement: 3,0 kW weight: 1.670 kg range L-W-H: 1150 x 1350 x 2050 mm Furnishing: - Welded steel structure body frame - AISI 4140 (42CrMo4) alloy steel crankshaft - CNC ground for maximum precision SnBz-12 quality - Bronze bearings, ground for minimal surface resistance - 4 sides pneumatic clutch-brake combination - PLC control for safety (PILZ Germany) - Photo cell light barriers around the work table (PILZ Germany) - Two-hand and foot pedal control - Adjustable stroke - Central lubrication system - CE safety approval by TÜV - electrical equipment SIEMENS, SCHNEIDER, PHOENIX, OMRON The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 10 t throat: 160 mm stroke: 0 - 40 mm table:: 270 x 370 mm table:: 100 mm - Bohrung no. of strokes: 200 Hub/min bore: 25,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 180 mm total power requirement: 0,75 kW weight: 590 kg range L-W-H: 1.168 x 1.010 x 1.670 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. saw blade diameter: 400 mm Pneumatic material tensioners

Key data: 100 t

Sale due to switch to eccentric press Pressing force 100 tons Loading depth 360 mm Stroke 500 mm Daylight 800 mm Plunger area 530 x 400 mm Table height above floor 710 mm Working speed 10mm/sec Approach speed 150 mm/sec Return speed 150 mm/sec Required power 17 kW Dimensions L x W x H 1,400 x 2,000 x 3,200 mm Weight of the machine approx. 5.1 t Year of manufacture 2001 Price is net, VAT can be claimed. Loading facilities available All information without guarantee

Stock# UG6388 Little used single screw extruder by Farmet (CZ) model FE100 WE Clever Max. Machine can reach output in range from 90-130 kg/h. Power consumption 16 kW. Includes water pump, die cutting knife, some toolings. Local control panel with plc controls. Previously tested on animal food production. Dims: L 195 cm x W 102.5 cm x H 178 cm x weight 600 kg.

pressure: 63 t throat: 260 mm stroke: 8-100 mm ram - range of adjustment: 63 mm no. of strokes: 115 Hub/min : 316 mm table surface area: 630x490 mm ram surface: 315x260 mm hole in the table: Ø 140 mm total power requirement: 4 kW weight of the machine ca.: 7,5 t dimensions of the machine ca.: 2000x2000x2700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Single Column Press Dunkes TYPE: HZS 160 Specifications: Manufacturer: Dunkes Model: HZS 160 Operating hours: approx. 2250 The machine is in good condition and fully functional.

A bevel gear rolling test machine Gleason is available. Workpiece diameter: 330mm, max. center distance: 203mm, driver spindle nose distance range: 100mm-250mm, max. offset range upper/lower: 203mm/50mm, driver spindle bore: 99mm, driver spindle taper per meter: 15.5mm/m, counter spindle bore: 58mm, counter spindle taper per meter: 12.7mm/m, spindle speed: 1500rpm, test angle range: 0°-180°, driver spindle repeatability: +/-0.004mm, runout: +/-0.003mm, machine dimensions X/Y: approx. 1550mm/2050mm, weight: approx. 2400kg. An on-site inspection is possible.

Holzzerkleinerer ( Holzhäckler ) maschine modell MION MOSOLE TR 2 gebrauchte maschine Maschinenbedienung im Automatik- und/oder Handbetrieb modus Arbeitsbedingungen: ausgezeichnet Im Automatikbetrieb startet der Motor in die entgegengesetzte Richtung, um den Stopfer von eventuellen Rückständen vorheriger Arbeiten zu befreien. Im Vollautomatikbetrieb stoppt der Motor nach ca. 5 Sekunden und startet erneut in die richtige Richtung für eine kontinuierliche Bearbeitung (siehe Video). Technische Daten : hydraulischer Schieber Breite Rotor mm.700 Durchmesser Rotor mm.300 Drehzahl Zerkleinerungseinheit 100 U/min Trichterinhalt 3.42 m³ Hauptmotor PS 25 Hydraulikaggregat Motorschieber PS 1 auswechselbare Messer Beschickung von oben

Komptech Terminator 5000 SD Category: Garbage Shredders Specification: Category: Universal Waste Shredder Serial / reference number: 481148 Power: 446 hp / 328 kW Weight: 27 000 kg Emission class: Tier 4 Final / Stage V Equipment and description: Terminator 5000 S Diesel engine: CAT C13 Tier 4 Final/Stage V F-Crushing Unit Armoured rollers – new Sickle teeth Hydraulically adjustable cutting gap 0-45 mm Overbelt magnet Central lubrication Remote control

VMC ECO S-1.800, Rotor length 1.800 mm, 132 kW Drive 380-400V 3Ph, 420 A 60Hz. IP55, complete with loading hopper, hydraulic ram 11 kW, hydraulic power station, control panel, good working conditions, Constructed in 11-2001, offered AS IS WHERE IS, installed power - used power in work: about 60-65% : 132 kW, availability: immediate, working width: 1.800 mm., options available: loading belt, extraction system, capacity: depending on materials and feeding rate, conditions: Very good, type: single shaft - electric

Screw Diameter: 75 mm // Throughput: 700 kg/h

Offer 25374 Specifications: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Lifting speed 25 mm/sec. - Return 125 mm/min - Installation height approx. 1000 mm - Projection to the middle of the ram 380 mm - Pusher clamping surface 530 x 400 mm - Plunger clamping pin 40 mm - Table size 750 x 560 mm - Table hole / through hole in the table 200 mm - Table height above floor 720 mm - Oil filling quantity approx. 200 ltr - Drive 400 V / 11 kW - Space requirement approx. W 1150 x H 3250 x D 1850 mm - Weight approx. 4600 kg

Screw Diameter: 35 mm // Output Capacity: 25 kg/h

Screw Diameter: 160 mm // Output Capacity: 1400 kg/h

Screw Diameter: 100 mm // Output Capacity: 600 kg/h

Screw Diameter: 65 mm // Output Capacity: 170 kg/h

Doppstadt DW 3060 D Single-shaft pre-shredder Equipment: MTU R 1100 EUROMOT IV diesel engine, 320 KW Total weight: approx. 25,000 KG 18-channel radio remote control Rear hinge 5.5 m, hydraulically foldable Comb extension Humidification device 21 roll teeth Form C DoppLock quick-change system 20 comb teeth trapezoid Overbelt magnet Hopper Elevation Service Details The machine is in very good technical and visual condition The machine receives a brand-new planetary gearbox before delivery Warranty: The machine will be sold in the condition existing at the time of delivery. The seller assumes no liability for defects We reserve the right to sell in advance, make changes and repairs.

Key data: 22 mm, 60

Single screw extruder 60 with renewed PMA control in 2010 - was replaced by double screw 5 years ago. Works after oil and belt change

: neu : ca. 4 Monate ab Auftragse : Italien : 120000 € : 2268 € : 300 to : 500 mm : 1000x500 mm : 1200x800 mm : 600 mm : 400 mm : 22 mm/s : 2 mm/s : 7.5 kW : 2300 mm : 1500 mm : 3100 mm : 11200 kg 4-fold round guidance table and ram with T-slots 2 hand operation Siemens PLC manometer users manual Light barrier € on Request Siemens control for programming of stroke and press time € on Request Siemens touchscreen-control, 50 programsstoreable, for programming: • Upstroke and downstroke quota • Break time in the bottom • time of Decompression • setting pressure of work • Pieces counter • prestop in upstroke and downstroke • setting for movement in manual and in automatic • management of alarms and anomalies € on Request Working hour counter € on Request Stroke counter € on Request Deompression valve € on Request Oil cooler with decompreission valve � ...

Jessinegg + Urban, Stroke 300, Lift: 300, table 450x370, 1300kg

Year: 2018 technically efficient, ready to work – after full service motor power: 2.2 kW disc diameter: 400 mm (cross-cut) machine head can be moved 45° to the right and left head tilt 45° to the left pneumatic profile clamps pressure reducer cooling system

pressure: 40 t stroke: 150 mm serial number: 100091 : 2 : Druck & Hub verstellbar pressure: 25 t weight: je 1,5 t safety light frame: ja bei beiden The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

- Brand: SILMISA - With hydraulic pusher - Model No.: MSA.30.126 - Year: 2008 - Power: 75 hp (55 KW) - Cutting chamber: 1260 x 900 - Blade: 40 x 40 mm - With electric panel

Key data: 20 mm, 25

single-screw laboratory extruder Collin E 20 M Output capacity: max. 5 kg/h (depending on material and processing conditions) Screw diameter: 20 mm, L/D = 25 Screw suitable for processing PE/PP (condition: excellent) Heating capacity cylinder: up to 300 C incl. mass pressure and temperature sensor Incl. motorized lifting device for the height adjustment of the processing unit incl. material funnel incl. clamping flange for nozzle attachment Total connected load: 17 kW Dimensions (L x W x H): 1,450 x 800 x 1,900 mm Weight: 300 kg Note: including complete documentation Condition: used, function-tested

Key data: 75 mm, 30

Single Screw Extruder Cincinnati TALOS 75-30G Output capacity: max. 450 kg/h (depending on material and processing conditions) Screw diameter: 75 mm, L/D = 30 Screw geometry for processing HDPE/PP 11 x Tool Zones incl. TC Type J ITIB 3-pin Thermal Probe incl. mass temperature and pressure sensor Interface for succession via CAN Open Bus Machine control Cincinnati EXcXP-touch Drive power main motor: 125 kW Total connected load: 178 kW Machine weight: 2,200 kg Remark: incl. spare engine (used) without material hopper Condition: used, function tested

Very nice 2003 Uniloy single station with double view-stripe head W.Müller CD125mm Machine never runs in production. Comes from a technical college for training students Current condition is very well and runs perfectly

Year: 2007 - technically efficient, ready to work – after full service - disc diameter: 420 mm - cooling installation - double-sided pneumatic clamp - angle-adjustable crank - pressure reducer

Press force: 100t, throat depth: 320mm, table dimensions X/Y: 850mm/610mm, ram dimensions X/Y: 600mm/355mm, stroke range: 10mm-130mm, ram adjustment: 80mm, stroke rate: 56rpm, installation height: 300mm, machine dimensions X/Y/Z: approx. 1900mm/1900mm/3150mm, weight: approx. 9000kg. On-site inspection is possible.

: neu : ca. 3-6 Wochen ab Auftrag : Türkei : 62500 € : 1181.25 € : 63 to : 750 mm : 500 mm : 170 mm : 4 - 102 mm : 54 1/min : 490x325 mm : 90 mm : 270 mm : 440 mm : 7.5 kW : 1800 mm : 1150 mm : 2750 mm : 4100 kg 8-fold ram guide front protection by light guard manual stroke adjustment ram adjustment witch ratchet drive over gear combined clutch brake unit with pneumatic control fix table single and continuous stroke foot pedal and 2 hand control mech. overload safety device automatic central lubrication user manual in GERMAN and ENGLISH according to CE rules The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Extrudeuse CM EVOLUTION PLAST type CM-EVO 230 Année. : 2019 Puissance : 50 KW Tension : 400 VOLTS Poids : 4000 KG

General SKU269X293 MakeCollin TypeTeach-line E20T and BL50T No.9120 3914 Year of construction2014 LocationBarneveld Main Features Motor9 KW Inlet diameter30 mm L/D25 Specified Features - Single screw extruder MaterialStainless steel Single screw extrudercheck Screw diameter20 L/D25 Number of heating zones:2 Electric heatingcheck Air coolingcheck DC-motor1,1 kW, 400 volt, 1400 rpm Feeding with hoppercheck Max. temperature300°C Information With switchgearcheck Floorspace0,85x0,65 m Total height0,70 m Weight100 kg CEcheck Extra SpecificationsWith Teach-line film blowing line, type BL50T, dia. Take off rolls, 50 mm, roll width 200 mm, max bubble dia. 110 mm, speed 13 m/min, : winder dia. 52 mm, max pulling force 95N, max coil dia. 300 mm : Single screw extrudersCollinExtruders > Single screw extrudersBrand > Collin What you can expect from Foeth: -- Machine is ...

Technical features: heated knives, weld bead limitation 0.2mm, optimization of the welding result through the parallel sliding welding process, individual adjustment of the welding parameters, quick changing of the outer contour allowances by means of holding magnets. Air consumption at 6bar: 15l/Takt, angle adjustment range: 30-180°, profile height: 30-105mm, max. profile width at 90°: 157mm, compressed air connection: 8.7bar, power: 2.7kW, supply voltage: 220V, 50/60Hz, length: 770mm, width: 880mm, height: 1560mm, weight: 320kg. An inspection on site is possible.

This Krauss Maffei KME 45 XS was manufactured in 2016. It features a 45 mm screw diameter, high-performance single screw with a 36:1 L/D ratio, and operates at speeds up to 120 rpm. Designed for high-pressure extrusion, it handles thermoplastics and compounds with a throughput of 150-300 kg/h. Consider the opportunity to buy this Krauss Maffei KME 45 XS single screw extruder. Contact us for more information about this machine.

Shredder of the leading company LINDNER model: KOMET 1800 single shaft number of knives 50pcs. Ideal for SRF/RDF (paper, plastic, fabric, wood), accompanied by the electrical panel and the control panel. Drive motor: 200Kw ABB 400V/50Hz Hydraulic unit: Dorninger-Heavy Duty 1:65lt/min ,Drive Capacity:11Kw The machine is in excellent condition, being sold due to replacement with a new more advanced model.

GT-5313 1-Spindle Extruder - Brand: PAGANI - Model: 75/ 30D-B - Spindle: Ø 75 mm - With electrical panel - Engine: 103 hp (77 kW) - Year 1995

GT-5315 1-Spindle Extruder - Brand: FLAG - Ø 120 mm - 2.2 meters long spindle - With 75 hp (55 KW) engine - No electrical panel