side channel used for sale

Specifications Maximum pressure: 65 tons Pressing force: 84 tons/m² Duct cross-section: 1000 x 750 mm Bale weight: do 550 kg Power supply: 400 V/ 45 kW Year of construction: 2011 Number of ties: 4 vertical Dimensions of the tailgate: 1400 x 920 mm Weight: approx. 13 tones Bale tying: automatic

Specifications Maximum pressure: 50 tons Press force: 7.14 kg/cm² Duct cross-section: 1000 x 700 mm Bale weight: do 500 kg Power supply: 400 V/ 30 kW Number of ties: 3 horizontal Dimensions of the tailgate: 1250 x 950 mm Weight: about 10 tons Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the duct. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the press chamber for easy maintenance

Specifications Maximum pressure: 56 tons Year of Make: 2016 Press force: 3.8 kg/cm² Number of bindings: 5 Channel cross-section: 1100 × 750 × 600÷1200 mm Dimensions of the tailgate: 990 × 1250 mm Bale weight: 250 - 500 kg Weight: approx. 15.5 - 17.5 t Power connection: 3 × 400 V250 - 500 kg Bale tying: automatic Drive power of the main motor 75 kW Nominal current of the main motor 125.22 A Pump capacity 438 l/min Oil cooler 4kW Oil heating 1 kW Theoretical throughput 535 m3/hour Theoretical flow rate to density 20 kg/m - 10.70 tons/hour Theoretical throughput to density 50 kg/m - 26.75 tons/hour Machine in operational condition, in continuous operation. Courtesy, please contact the seller directly regarding this machine tel. 508 115 007

Unaudited Auction-ID: A7-45427-264

Specifications Maximum pressure: 45 tons Year of Make: 2017 Pressing force: 6.9 kg/cm² Number of bindings: 3 Channel cross-section: 900 × 720 × 600 - 1200 mm Dimensions of the tailgate: 820 × 1250 mm Bale weight: 250 - 400 kg Weight: approx. 7 t Power connection: 400 V Bale tying: automatic Theoretical throughput 174 m3/hour Theoretical throughput to density 20 kg/m - 3.48 tons/hour Theoretical flow rate to density 50 kg/m - 8.7 tons/hour If you have any questions, please call us: +48 696 072 985

Specifications Maximum pressure: 85 tons Year of Make: 1994 Pressing force: 103 tons/m² Number of ties: 4 - vertical Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1750 mm Bale weight: 500-650 kg Weight: 26 tons Power connection: 400 V/ 55 kW Bale tying: automatic

Specifications Maximum pressure: 100 tons Year of Make: 1995 Pressing force: 82 tons/m² Number of ties: 5 in vertical Channel cross-section: 1100 x 1100 mm Dimensions of the tailgate: 2050 x 1100 mm Power connection: 400 V/ 2 x 55 kW Weight: approx. 36 tons Bale tying: automatic Press capacity under operating conditions: max 1170 m³ / hour Press capacity at idle: max 720 m³ / hour Theoretical throughput: to density 30kg/m³) 22 tons/hour Theoretical throughput: to density 50kg/m³) 28 tons/hour Theoretical throughput: to density 100kg/m³) 42 tons/hour Open hopper allows filling with the conveyor belt Pre-pressing flap Automatic regulation of the channel Automatic binding with wire Choice of the length of the finished bale thanks to the bale counter Compact hydraulic power unit with low noise emissions Press plate stably guided on large rollers ...

High-pressure pump for baler HSM 500.1 VL with 7.5 kW motor

baler hydraulic power pump HSM V-press 1160 Plus

Specifications Maximum pressure: 75 tons Year of Make: 1999 Press force: 90.9 t/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1550 mm Bale weight: 500-750 kg Weight: approx. 25 tons Power connection: 400 V Bale tying: automatic Motor: 75 kW (possibility of switching to 55 or 45 kW) Press capacity at idle: max 750 m³ / hour Press capacity under operating conditions: max 350 m³ / hour Theoretical throughput to density 35 kg/m3: approx. 12 tons/hour Theoretical throughput to density 60 kg/m3: approx. 21 tons/hour Theoretical throughput to density 100 kg/m3: approx. 33 tons/hour Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Cho ...

used baler Herateller: PAAL Type: PACOMAT II Year of Make: 1995 Specifications: Pressing force: 27 t Drive power: 18.5 kW Total connected load: 25 kW Throughput: 115 m³/h Filling opening: 1,000 x 650 mm Channel format: 1,000 x 700 mm (H x W)

automatic baler Manufacturer: PAAL Type: KONTI 425 D Year of Make: 2002 Hours: 58,245 h specifications: Press force: 115 t Specific pressing force: 139.39 N/cm² Drive power: 3 x 45 kW (main pumps) Total connected load: 170 kW Capacity under operating conditions: approx. 475 m³/h Filling opening: 2,000 x 1,020 mm Channel cross-section: 750 x 1,100 mm (H x W) Bale size: 1,100 x 750 mm Binding: 4-fold vertical Weight: approx. 36 t Special equipment of the press: • Reduction of the filling opening due to adjustable pressure plate position • Control Siemens S7 • Automatic cutting edge free kick

automatic baler Manufacturer: PAAL Type: Pacomat IS Year of Make: 1990 specifications: Pressing force: 27 t Specific pressing force: 5.51 kg/cm² Total connected load: 23 kW Rated current: 46 A Main drive power: 18.5 kW Capacity: 80 m³/h Control: Siemens S5 100 U Bale size: 700 x 700 Filling opening: 800 x 600 mm

automatic baler Manufacturer: PAAL Type: KONTI 125 SO Year of Make: 1990 specifications: Press force: 40 t Specific pressing force: 5.7 kg/cm² Channel format: 700 x 1,000 mm Bale weight: 375 - 450 kg, depending on material and bale length Filling opening: 1,400 x 920 mm Machine weight: approx. 10 t Drive power: 22 kW Throughput: 115 m³/h Pressing capacity: approx. 4.00 t/h at department store (35 kg/m³ bulk weight) approx. 6.75 t/h for mixed paper (60 kg/m³ bulk weight) approx. 10.0 t/h for collected goods (100 kg/m³ bulk weight)

automatic baler Manufacturer: PAAL Type: KONTI 425 C / SO Year of Make: 1995 Operating hours: approx. 36,000 hours specifications: Press force: 100 t Specific pressing force: 121.2 N/cm² Drive power: 2 x 75 kW (main pumps) Total connected load: 171 kW Capacity under operating conditions: approx. 380 m³/h Filling opening: 1,750 x 1,020 mm Channel cross-section: 750 x 1,100 mm (H x W) Bale size: 1,100 x 750 mm Binding: 4-fold vertical Weight: approx. 36 t

automatic baler Manufacturer: PAAL Type: KONTI 600 F/k with cross-binding Year of construction 2008 only 4 years in operation specifications: Press force: 145 t Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 2 x 75 kW Throughput capacity:approx. 510 m³/h Capacity at 35 kg/m³: 17.5 t/h Capacity at 60 kg/m³: 30.0 t/h Capacity at 100 kg/m³: 47.0 t/h Binding: 5-fold vertical Additional 4-fold automatic horizontal bonding Bale weight: approx. 800 - 1,250 kg depending on baled material and bale length Machine weight: up to approx. 39 t

Fully automatic baler Manufacturer: PAAL Type KONTI 275 B specifications: Pressing force: 60 t Specific pressing force: 7.30 kg/cm² Drive power: 1 x 37 kW Throughput under operating conditions: 200 m³/h Output at 35 kg/m³ bulk density: approx. 7 t/h Output at 60 kg/m³ bulk density: approx. 12 t/h Filling opening: 1,020 x 1,550 mm Bale size:750 x 1,100 mm Machine weight: approx. 21 t Bale weights: up to approx. 600 kg

automatic baler Manufacturer: PAAL Type: KONTI 275 D Year of Make: 2000 Operating hours: approx. 23,575 hours Main parts of the press: 1 automatic channel press 1 automatic lacing 1 hydraulic system 1 Electrical control specifications: Press force: 75 t at 300 bar Specific pressing force: 9.09 kg/cm² Channel cross-section (h x w): 750 x 1,100 mm Filling opening: 1,020 x 1,550mm Number of binding wires: 4 pieces vertical Drive power: 1 x 75 kW Throughput: up to approx. 350 m³/h Hydraulic oil tank capacity: 1,250 l Operating voltage: 3 x 400 VAC / 50 Hz / N / PE

3-Kanal PU Saugrad / 3-channel PU suction Wheel Heidelberg Saugrad Neuwertig / as new passend für alle Stahl / Heidelberg Anleger ab einer Arbeitsbreite von 56 cm Suitable for all Stahl / Heidelberg feeders with a working width of 56 cm

Specifications: - Machine for the production of longitudinal folds on the edges - square or rectangular longer channels and - Number of roller shafts with folding rollers 15 pcs - Material thicknesses from 0.5 - 0.63 mm - Duct dimensions from 80 x 80 mm - up to 100 x 100 mm - from duct dimensions 100 x 100 mm - Material thicknesses 0.5 to 1.0 mm - Throughput speed 15 m/min - Pneumatic connection - Drive 400 V / 3 kW -with: - E. - Footswitch - Duct baffles - Separate lubrication device - Space requirement approx. W 5400 x H 1200 x D 800 mm - Weight approx. 950 kg

Maximum pressure: 50 tons Year of Make: 2006 Pressing force: 65 tons/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1000 mm Dimensions of the tailgate: 920 x 1400 mm Bale weight: 350-500 kg Weight: approx. 13 tons Power connection: 400 V/ 22 kW Bale tying: automatic

Specifications Maximum pressure: 32 tons Pressing force: 4.33 kg/cm2 Number of bindings: 4 horizontal Channel cross-section: 820 x 900 x reg mm Dimensions of the tailgate: 82 x 135 cm Bale weight: bos 400 kg Weight: approx. 6.1 tons Power connection: 380 V/ 22 kW Bale tying: automatic

Technical data: Maximum pressure: 60 tons Year of Make: 1999 Press force: 72.7 t/cm² Number of Bindings: 4 Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1400 mm Bale weight: 450-650 kg Weight: approx. 20 tons Power connection: 400 V/ 45 kW Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the bale chamber for easy maintenance If you have any further questions about this or similar channel balers, please do not hesitate to contact us by email or phone!

Specifications: Maximum pressure: 40 tons Year of Make: 2007 Pressing force: 63 tons/m² Oil tank: 600l Bale weight: 300-400 kg Weight: approx. 7.6 tons Power connection: 400 V/ 15 kW Bale tying: automatic Open hopper allows filling with the conveyor belt. Automatic regulation of the light from the channel. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers

Hello, We hereby offer you a used baler from the manufacturer Presto GmbH & Co. KG, type HPK 50 B. The following technical data have been taken from the manufacturer's operating instructions and brochures, for which we cannot assume any liability for accuracy and completeness. Manufacturer: Presto GmbH & Co. KG Type HPK 50 B Year of manufacture 2005 Hours 15606 Hours Press force main press 50 t Drive power 30 kW Total connected load 31.5 kW Rated current 64 A Throughput under operating conditions at a bulk density of 60 kg/cbm approx. 6.7 t/hour Machine weight press 12.5 t Note: The machine has been repaired in our workshop (main control valve on the hydraulic block replaced) and tested on the fly, in manual and automatic mode. The machine documentation is available in German. A tour of the press is possible by appointment in our workshop. We would be happy if  ...

Available from June 2026 Presto HPK 50 BS baler, built in 2011, with vorbulator and optional chain belt conveyor Horstmann Manufacturer: Presto Type: HPK 50 BS Year of Make: 2011 Drive: 30 KW Press force: 50 t Filling opening: 1600 x 1050 mm (LxW) Channel cross-section: 700 x 1100 mm Filling volume, max. 1.23 m³ Cycle time: 19 s Binding: 4-fold throughput at 35 kg/cbm: 6 t/h 60 kg/cbm: 9.6 t/h 100 kg/cbm: 13.9 t/h Bale weight: up to 500 kg Machine dimensions: 8500 x 1700 x 2400 mm (LxWxH) Machine weight: approx. 12,000 kg Data Chain Belt Conveyor Manufacturer: Horstmann Type: PK 1100/11 Year of Make: 2011 Belt width 1100 mm Speed: approx. 0.2 m/s (max. 0.3 m/s) Feed length approx. 3000 mm Climbing part approx. 5000 mm Gooseneck approx. 1000 mm The press is still in use and can be viewed under operating conditions. It will be available from the beginni ...

Color: Yellow Single length 1.80 m Original packaging Price per single length (1.80 m) = 4.00 € + VAT Pick-up or shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Color: Yellow Single length 2 m Original packaging Price per m = 5.00 € Minimum purchase quantity = 8 m Pick-up or shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Color: Yellow Single length 2 m Minimum purchase quantity = 8 m Used Price per m = 3.00 € + VAT Pick-up or shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Color: Yellow Original packaging Price per unit = 15.00 € + VAT Pick-up or shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

https://www.behringer.com/product.html?modelCode=0601-ADG Sale with the following accessories: 1x IEC connection cable C13 Auction-ID: A7-45172-50

Technical data: Maximum pressure: 48 tons Year of Make: 2019 Press force: 5.8 kg/cm² Number of Bindings: 4 Channel cross-section: 1100 × 750 × 600÷1200mm Dimensions of the tailgate: 1020× 1250 mm Bale weight: ok. 300-550 kg Weight: approx. 10 t Power connection: 400 V/22kW Bale tying: automatic Theoretical throughput to density 20 kg/m - 4.8 tons/hour Theoretical throughput to density 50 kg/m - 12 tons/hour The machine is fully functional.

Color: Black Single length = 2 m Original packaging Minimum purchase quantity = 8 m Price per m = 13.00 € + VAT Pick-up and shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Color: Black Used Single length = 2 m Price per m = 7.00 € + VAT Minimum purchase quantity = 8 m Pick-up or shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Color: Black Original packaging Price per unit = 19.00 € + VAT Pick-up and shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Color: Yellow Original packaging Single length = 2 m Price per m = 13.00 € + VAT Pick-up and shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Color: Yellow Used Single length = 2 m Price per m = 7.00 € + VAT Pick-up or shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Dedy cooling channel Stainless Steel Cooling unit installed very good condition Connection 230V Used machine

Color: Yellow Original packaging Price per unit = 15.00 € + VAT Pick-up and shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Color: Yellow Original packaging Price per unit = 18.00 € + VAT Pick-up and shipping available Shipping costs will be charged separately Item invoice due when ready for shipment

Baler Paal Konti 325 D/SO, built in 1999 Technical data: Manufacturer: Paal Type Paal Konti 325 D/SO Built in 1999 Hours: 50702 Press force 94 t Drive power: 2 x 45 kW Total connection 104 kW Filling opening 1020 x 1750 mm Bale dimensions 750 x 1100 mm, length variable 4-fold automatic tying Throughput at 35 kg/m³ approx. 14 t/h 60 kg/m³ approx. 24 t/h 100 kg/m³ approx. 38 t/h Bale weight 525 to 800 kg Transport dimensions approx. 12352 x 2340 x 2800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: paper, cardboard, light waste, plastic waste Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale against advance payment is made ex wor ...

Unaudited Good condition Auction-ID: A7-45427-210

Dynacord Ps 800 8-Channel Power Mixer Mixer Auction-ID: A7-45427-112

Available from 15.05.2026 Baler Paal Konti 325 G, built in 2013 Technical data: Manufacturer: Paal Type Konti 325 G Year of construction 2013 Operating hours 11,723 (as of 10.02.26) Press force 100 t Drive power 2 x 55 kW Filling opening 1020 x 1750 mm Bale dimensions 750 x 1100 mm, length variable Setting 5-fold automatic Throughput at 35 kg/m³ approx. 13.5 t/h 60 kg/m³ approx. 21.5 t/h 100 kg/m³ approx. 33 t/h Bale weight up to 800 kg Transport dimensions approx. 12216 x 2530 x 2800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: paper, cardboard, light waste, plastic waste Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sal ...

Technical data: Maximum pressure: 40 tons Year of Make: 2002 Press force: 50.5 t/m² Oil tank: 600l Bale weight: 375-525 kg Weight: approx. 15 tons Power connection: 400 V/ 15 kW Bale tying: automatic Open hopper allows filling with the conveyor belt. Automatic regulation of the light from the channel. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the bale chamber for easy maintenance

4 CUTTER HEADS, MAX. DIMENSIONS OF THE WORK PIECE: 180/120 MM, MIN. DIMENSINS OF FINISHED WORK PIECE: 16/7 MM, SPINDLE SPEED: 6000 RPM, OPERATION HOURS: 30 HOURS ONLY!

Kragarmregal, double-sided, 5.18m height, 1.20m arms, 870kg per arm - NEW - : Price from location incl. loading! 1 shelving unit with 4 pcs 2,495.-EUR (net)! A Kragarm shelving system, hot-dip galvanized, consisting of: 4 double-sided shelves approx. 5.18 m high, hot-dip galvanized IPE 180 / 100 with 2x3 each. Arms 1.20 m, 870 kg load capacity per arm with verbatim approx. 1.30 m shelf divider approx. 5180mm high, hot-dip galvanized foot and arm depth 1200 mm with 3 adjustable shelf arms each with centre of gravity 600 mm 870 kg per arm / 2610 kg per stalker with laengs and diagonal connectors e = 1300 mm for a shelf row with 4 stems approx. 4000 mm long with all screws and nuts, without bottom anchors . Other configurations (frame height, armrails, arm types, etc.) can be used! Please contact us! photos of an old shelf!; New

Kragarmregal, double-sided, 5.18m height, 1.20m arms, 500kg per arm - NEW - : Price from location incl. loading! 1 shelving unit with 4 pcs 2,295.-EUR (net)! A Kragarm shelving system, hot-dip galvanized, consisting of: 4 double-sided shelves approx. 5.18 m high, hot-dip galvanized IPE 180 / 80 with 2x3 each. Arms 1.20 m, 500 kg load capacity per arm with verbatim approx. 1.30 m shelf divider approx. 5180mm high, hot-dip galvanized foot and arm depth 1200 mm with 3 hoes-adjustable shelf armseached carrying capacity at load centre 600 mm 500 kg per arm / 2610 kg per staender with laengs and diagonal connectors e = 1300 mm for a shelf row with 4 stems approx. 4000 mm long with all screws and nuts, without bottom anchor s. Other configurations (frame height, armrails, arm types, etc.) can be used! Please contact us! photos of an old shelf!; New

Kragarmregal, double-sided, 4,16m height, 1.20m arms, 500kg per arm - NEW - : Price from location incl. loading! 1 shelf unit with 4 pcs 1.850.-EUR (net)! A Kragarm shelving system, hot-dip galvanized, consisting of: 4 shelves double-sided approx. 4.16m high, hot-dip galvanized IPE 160 / 80 with 2x3 each. Arms 1.20 m, 500kg load capacity per arm with verbatim approx. 1.30 m shelf divider approx. 4160mm high, hot-dip galvanized foot and arm depth 1200 mm with 3 hoes-adjustable shelf arms carrying ability at load centre 600 mm 500 kg per arm / 2250kg per stem with laengs and diagonal connectors e = 1300 mm for a shelf row with 4 stems approx. 4000 mm long with all screws and nuts, without bottom anchors. Other configurations (frame height, armrails, arm types, etc.) can be used! Please contact us! photos of an old shelf!; New

Kragarmregal, one-sided, 3m height, 1.20m arms, 500kg per arm - New goods - : Price from location incl. loading! 1 shelving unit with 4 staenders 1.150.-EUR (net)! A Kragarm shelving system, hot-dip galvanised, consisting of: shelf edges on one side approx. 3,000 mm high, hot-dip galvanized foot and arm depth 1200 mm with 3 hoe-adjustable shelf arms carrying ability at load centre 600mm 500 kg per arm / 2250 kg per stem at 4 staenders per arm level 4 x 500 kg = 2,000 kg with lashings and diagonal connectors e = 1300 mm for a row of shelves of 4 stems approx. 4000 mm with all screws and nuts, without bottom anchors.; New