shr 25 used for sale

Pressure: 40 bar Motor: 11 kW Free air delivery: 2,42 m³/min Measurement (WxHxD): 1652 x 1456 x 928 Weight: 662 kg Compressed air connection: 1/2

Pressure: 40 bar Motor: 11 kW Voltage: 400 Volt / 50 Hz Free air delivery: 0,78 m³/min Measurement (WxHxD): 6300 x 1500 x 806 Weight: 490 kg Compressed air connection: 1/2

Brand Lisec Type Butyl extruder machine Model LBH-25ARS + 2x RAV2 Serial number 572-003937 Year of construction 2000 Weight 2.1ton Power 7kVA Air pressure 6bar Water pressure: N/A Length +/- 11m Width +/- 5m Height +/- 3.5m Working height ,4m Transport dimensions L x W x H Special 2 pcs 3.5×2.6x2m + 6×1.5×3.2 Max speed Min.-max. profile 4-15mm Min.-max glass size 2.5×3 Number of brushes n/a Number of spindles n/a State machine nvt Type of control B&R Electrical connection 380+N+PE Instructions for use yes Electrical diagram yes Parts list available on request Available software backup Photos/film available: Photos and video available

Brand Lisec Type Butyl extruder machine Model LBH-25ARS + 2x RAV2 Serial number 572-003937 Year of construction 2000 Weight 2.1ton Assets 7kVA Air pressure 6bar Water pressure: NVT Length +/- 11m Width +/- 5m Height +/- 3.5m Working height ,4m Transport dimensions L x W x H Special 2 pcs 3.5×2.6x2m + 6×1.5×3.2 Min.-max. profile 4-15mm Min.-max glass size 2.5×3 Number of brushes n/a Number of spindles n/a State machine n/a Type of control B&R Electrical connection 380+N+PE Instructions for use Yes Electrical diagram Yes Parts list available on request Available software back up Photos/film available: Photos and video available

Brand Lisec Type PSL-35/25V Model Frame Placing Machine Serial number 020 35.20.09 + 252523 Year of construction 1999/ 1993 Weight 1.85 tons Assets 1.9 kVA Air pressure 6 bar Electrical connection 400 Volt Photos/film available: Photos available

Foot: 900 mm Vertical: 4980 mm Head: 2770 mm Belt speed: 0.47 m/s Flow rate: 10.0 cbm/h Bulk density: 0.18-0.25 t/cbm Engine power: 0.55 kW Speed range: 136 rpm Chain drive: 5/8" Chain Pulley Motor: Z = 15 Sprocket B. movement: Z = 38 Shaft design: sheet steel 3+4mm Removable side plates in the base Further measurements can be found in the attached plan.

Cutting length X/Y: 250mm/250mm, max. sheet thickness steel/stainless steel: 6mm/4mm, table dimensions X/Y: approx. 1200mm/900mm, weight: approx. 1200kg. Including a 500mm stop extension. An on-site inspection is possible.

Press force: 2800kN, heating platen size X/Y: 500mm/500mm, daylight between the heating platens: 200mm, max. hydraulic pressure: 300bar, heating power: 9.4kW, drive power: 7.5kW, control: Siemens S5 with OP17, weight: approx. 4500kg. Equipped with sliding table, vacuum pump, vacuum chamber and vacuum receiver tank. An on-site inspection is possible.

Maplan 250ton Injection Machine Injection MTF 1500/250 Platen size = 630mm x500mm Stripper plate/ejectors =top only Max gap between platens = 702mm Volume = 1500 ccm3 Tonnage = 250T Year 2007

Press force: 2800kN, heating platen size X/Y: 500mm/500mm, daylight between the heating platens: 200mm, max. hydraulic pressure: 300bar, heating power: 9.4kW, drive power: 7.5kW, control: Siemens S5 with OP17, weight: approx. 5000kg. Equipped with sliding table, vacuum pump, vacuum chamber and vacuum receiver tank. An on-site inspection is possible.

Fully functional welding machine

; Gross weight [kg]: 5395; Engine: Perkins 2506C-E1STAG2; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 775

Vibratory Spiral Conveyor / Sorting Device / Spiral Conveyor / Vibratory Conveyor RNA Vibrating Bowl, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwing TechnologyFeeding System, Feeding DeviceManufacturer: RNA Rhein-Nadel Automation GmbHTyp: SRC-N 250-2LSer.- No: 03613 Year of Construction: approx. 2000Pot Diameter Bottom: 250 mmPot Diameter Top: 380 mmPot Inner Height: approx. 70 mmSorting Lane Width: 30 mmTotal Height (Drive + Pot with Sorting Path): 390 mmOscillation Frequency: 100 Hz / 6000 min-1Power supply: 230 volts, 50 Hz control unit

; Gross weight [kg]: 21000; Engine: Caterpillar 3516; Accessories: Tanker, Battery, Control Panel, Stahldach

Vibratory Spiral Conveyor / Sorting Device / Spiral Conveyor / Vibratory Conveyor RNA Shaking Bowl, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwing TechnologyFeeding System, Feeding DeviceManufacturer: RNA Rhein-Nadel Automation GmbHTtype: SRC-N 250-2LSer.- No: 03609 Year of Construction: approx. 2000Pot Diameter Bottom: 300 mmPot Diameter Top: 350 mmPot Inner Height: approx. 25 mmSorting Track Width: approx. 30 mmTotal Height (Drive + Pot with Sorting Track): 380 mmOscillation Frequency: 100 Hz / 6000 min-1Power supply: 230 volts, 50 Hz

Vibratory Spiral Conveyor / Sorting Device / Spiral Conveyor / Vibratory Conveyor RNA Shaking Bowl, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwing TechnologyFeeding System, Feeding DeviceManufacturer: RNA Rhein-Nadel Automation GmbHTyp: SRC-N 250-2LSer.- No: 03611 Year of Construction: approx. 2000Pot Diameter Bottom: 300 mmPot Diameter Top: 350 mmPot Inner Height: approx. 25 mmSorting Track Width: approx. 30 mmTotal Height (Drive + Pot with Sorting Path): 380 mmOscillation Frequency: 100 Hz / 6000 min-1Power supply: 230 volts, 50 Hz- The

This 5-axis DMG MORI MORI NLX 2500/700 SY was manufactured in 2023. It features a turning length of 700 mm and a powerful main spindle with a maximum speed of 4,000 rpm. The machine is equipped with a 12-station turret and integrated automation for efficient parts handling. If you are looking to get high-quality turning capabilities, consider the DMG MORI MORI NLX 2500/700 SY horizontal turning machine we have for sale. Contact us for further details.

Travel X/Y/Z: 600mm/500mm/400mm, table dimensions X/Y: 900mm/600mm, spindle mount: SK40, speed: 6000rpm, tool positions: 24, feed: 6m/min, rapid traverse: 15m/min, machine dimensions X/Y/Z: approx. 4000mm/4000mm/2700mm, weight: approx. 5000kg. On-site inspection is possible.

cutting width: 150 mm machine weight ab.: 300 kg : 27468 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Decoiler Coil weight: 2,5 ton Material width: 50 - 500 mm Coil exterior diameter: 1400 mm Expansion range: 420 - 520 mm Leveller / Straightener Material width : 500 mm Number of levelling rolls: 9 pcs. Diameter of the levelling rolls: 50 mm Number of pinch rolls: 2 pcs. Material thickness: 6 mm Cross section: 3000 sq mm Feeding speed: 6 - 24 m / min

cutting diameter: 255 mm saw band length: 2765x 0,9 x 27 mm cutting width: 300 x 180 mm turning speeds: 35 + 70 U/min total power requirement: 1,8 kW weight of the machine ca.: 450 t dimensions of the machine ca.: 1,7 x 1,23 x 1,75 m SPECIAL PRICE! Double miter metal band saw, frequency converter hydraulic semi-automatic GBS 250 Super HA-I Easy • miter left 60° + right 45° • Material height sensor (automatic cut start detection) • Frame and gear made from one piece, very quiet cut and very low vibration • Hydraulic vice can be moved sideways a. • Guided, high quality industrial bearings • Solid vice + machine casting • Large machine bed • Machine base with tool compartment and chip drawer • Cut monitoring by ammeter • Cutting pressure feed regulator • Support roller (infeed side) • Ball bearing turntable Semi-automatic function: 1. Clamp material 2. Saw starts 3 ...

A Trima CNC gantry machining center is available. Workpiece dimensions X/Y/Z: 2500mm/1100mm/80mm, spindle power: 7.5kW, speed: 24000rpm, tool positions: 10, traversing speed X/Y/Z: 55m/35m/15m/min. Machine dimensions X/Y: approx. 4400mm/2500mm, weight: approx. 3200kg, control: Siemens Sinumerik. The machine has a control defect. The reference run is aborted. Documentation available. On-site inspection is possible.

turning diameter: 250 mm turning length: 100 mm control: SIEMENS 840 D total power requirement: 35 kW weight of the machine ca.: 7500 kg dimensions of the machine ca.: m E M A G (Germany) Vertical CNC Controlled Hard Turning and Grinding machine with tool turret and workpiece handling System Model VSC 250 DS Year 2004 # M7 28.69324 _______________________________________________________ Turning Ø, max. 250 mm Turning length internal / external 100 mm Workpiece length min./max. 29 – 100 mm 6-positon tool turret Ø / swing-Ø 480/790 mm Workpiece spindle Slide travel, X / Z / stroke 680 / 400 / 200 mm Feed rate / Quick feed X/Z 45/30 m/min. Feed force X/Z 5,5/11 kN Spindle speed 4.300 / 6.000 rpm Spindle drive 28 kW Total electrical load, ...

pressure: 2,5 kN stroke: 45 mm throat: 90 mm Working height from to: 80 - 220 mm table surface area: 120 x 60 mm weight of the machine ca.: 22 Kg dimensions: 160 x 230 x 390 mm Hand presses with rack HZ 250 The power is transmitted via a rack and pinion construction. she finds their use where during the working process a constant pressure is needed. Precisely manufactured, spindle hardened and ground, unlimited service life Long spindle guide, optimal pressure performance, T-slot according to DIN 650 milled in the middle, sliding blocks fit exactly. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

core drilling diameter max.: 25 mm bore depth: 1000 mm swing diameter: mm total power requirement: 25 kW weight of the machine ca.: 12,5 t dimensions of the machine ca.: m T B T (Germany) CNC-Controlled Horizontal Deep Hole Drilling Centre Model BWP 250 Year 1996, but reconditioned mechanically and electrically in 2006 ______________________________________________________________________ _____________ Working range: X Axis, machine column cross 2,000 mm Z Axis, drilling slide horizontal 1,200 mm Drilling depth 1.000 mm Y Axis, drilling slide vertical 1,100 mm Table clamping area 1,200 x 2,000 mm Drilling capacity in solid material, approx. 4 - 25 mm Tool holder taper HSK 50 Spindle speeds 1.260 - 15,000 rpm Feed rates / quickfeed, XYZ, infinitely variable 100 - 10,000/15.000 mm/min. Force rate of feed  ...

capacity 90 degrees: round: 255 mm capacity 90 degrees: square: 240 mm : 300 x 180 saw band length: 2.765 x 27 x 0,9 mm mm table height: 870 mm band speed: 18 - 110 m/min Control: CNC total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,63 t dimensions of the machine ca.: 1,8 x 1,85 x 1,85 m Miter band saw, fully automatic GBS 255 Super VA-I CNC • miter left 45° automatic operation • miter left 60° semi-automatic operation (cuts without programming) • Material height sensor (automatic cut start detection) • Frame and gearbox made from one piece, very quiet cut and very low vibration • Removable chip tray (disinfection) • Shockproof and ergonomic control panel with oil-resistant EPDM cover • High performance positioning with incremental encoder (CNC) c. • Top access to the saw, material and feed unit • Hinged safety cover • Fine feed adjustment • Semi-a ...

Saw blade diameter: 255 mm Sawblade tiltable: 45 ° Cutting height: 75 mm Table dimensions: 640 x 920 (ausgezogen) mm Saw blade: 30 mm Motor output: 1,6 kW connected load frequency: 230 V machine weight ab.: 32 kg Dimensions (L/W/H): 720 x 1080 x 920 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 125 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 0,75 kW weight of the machine ca.: 0,135 t dimensions of the machine ca.: 1,25 x 0,6 x 0,6 m Speed in 6 levels 125 - 2000rpm. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. (Independent) Fixed bezel. Revolving bezel. 4-fold steel holder. chip tray. back panel. spindle protection. Hardened bed rails. Longitudinal feed with left / right switching. Set of change gears. Associated Tools. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding wheel diameter: 250 mm no. of working stations: 2 Stück connected load frequency: 230 V turning speeds: 2850 U/min total power requirement: 1,5 kW weight of the machine ca.: 25 Kg dimensions: 0,65 x 0,32 x 0,35 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 250 mm saw band length: 3150 x 27 x 0,9 mm table height: 700 mm cutting width: 250 x 320 mm cutting speed: 25 - 90 m/min dimensions of saw-band: 2480 x 27 x 0,9 mm : 120 mm : 120 mm : 190 mm Impact energy: 190 mm connected load frequency: 400 Volt total power requirement: 1,5 kW weight of the machine ca.: 0,5 t dimensions: 0,95 x 1,16 x 1,98 m Rock-solid band saw for solid material - Double miter cuts up to 60° - AutoCut - Vice with quick clamping device - Belt tension control - Electric automatic cooling system - Material suggestion The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding wheel diameter: 250 mm connected load frequency: 230 V : 90 - 180 U/min weight of the machine ca.: 18 Kg dimensions: 470 x 300 x 440 m Knife sharpening device with variable speed Grinding wheel 250 x 50 x 12mm, grit 220 Leather disc 200 x 30 x 12mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 255 mm capacity 90 degrees: square: 240 mm : 300 x 180 saw band length: 2.765 x 27 x 0,9 mm mm table height: 870 mm band speed: 18 - 110 m/min total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,63 t dimensions of the machine ca.: 1,8 x 1,85 x 1,85 m Miter band saw, fully automatic GBS 250 Super VA-I MPS • Miter left. 45° automatic operation • Miter left. 60° semi-automatic operation (cuts without programming) • Shockproof and ergonomic control panel with oil-proof EPDM cover a. • Material height sensor c. (Automatic cut start detection) • Frame and gearbox made from one piece, very quiet cutting and very low vibration • Chip tray can be removed (disinfection) • Easy access to the saw, material and feed unit • Foldable safety cover • Fine feed adjustment • Semi-automatic. Cut! Saw automatically with microprocessor control Adj ...

turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 1,1 kW weight of the machine ca.: 0,15 t dimensions of the machine ca.: 1,3 x 0,6 x 0,65 m Benchtop lathe 3-axis LCD digital display system fully assembled. Longitudinal feed. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. Clamping plate. 4-way steel holder. Clock for thread cutting. Drip tray Hardened bed tracks. Emergency stop switch. Forage protection Set of wheels. Appropriate tools. Base cabinet is optional The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 250 mm capacity 90 degrees: round: 80 mm capacity 90 degrees: square: 70 mm capacity 90 degrees: flat: 95x60 mm capacity 45 degrees: round: 70 mm capacity 45 degrees: square: 60 mm capacity 60 degrees: flat: 65x60 mm total power requirement: 1,0 kW weight of the machine ca.: 0,075 t dimensions of the machine ca.: 0,3 x0,8 x0,75 m SPECIAL PRICE! The ideal metal circular saw for workshop and assembly • For miter cuts left up to 45° • For sawing steel, stainless steel and, to a limited extent, aluminum profiles • Spindle vice with double clamping arm for low-burr cuts • Optionally with 230 V or 400 V motor • Automatic cooling directly on the saw blade • Double bearing for saw head • 24 V safety switch in the handle with restart lock • Length stop, assembly tool • Subframe (option) additional price 172,-EUR ATTENTION: Price is without saw blade! (saw bl ...

turning diameter over bed: 250 mm turning diameter over slide rest: 130 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 20 mm tailstock quill taper MT: 2 tailstock quill stroke: 60 mm metric threading: 0,4 - 3,0 mm thread - inch: 10 - 44 TPI thread - module: 0,2 - 12,5 mm connected load frequency: 230 V total power requirement: 1,0 kW weight of the machine ca.: 0,12 t dimensions of the machine ca.: 1,09 x 0,59 x 0,45 m Equipped with - 20 mm spindle passage - adjustable guideways - Powerful 1.0 kW motor - continuously variable speed Scope of delivery: - 3-jaw chuck 100 mm, - 4-jaw faceplate chuck 125mm - standing and rotating bezel - Splash guard - Feed protection The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: Suitable for dressing and profiling diamond and CBN grinding wheels. ccesories: Total enclosure., Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel),, Wheel motor strengthened to 4 kW,, Dressing wheel motor strengthened to 2,2 kW,, 2 Machine lights 12 V,, Optical linear scale with digital display counter (0,001 mm) X, Z Axes,, 2/3” TV Camera with 15” LCD monitor (microscope with zoom 15‐120X included),, High performance swivelling angle reader (0,05°),, Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm,, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm,, Stepless oscillation speed,, Automatic central lubrication,, SIC Wheel dresser manual,, Grinding wheel holder:: HSK 50 E, Diamond grinding wheel diameter: 50 - 250 mm, max. width of grinding wheel: 70 mm, Grinding wheel bore diameter: 20 mm, Speed of ...

Machine designed for profiling and dressing flats, side, angular, radius and special shapes on diamond and CBN wheels. Especially suitable for single or multiple wheel packs., Accessories:, Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel),, Wheel motor strengthened to 4 kW,, Dressing wheel motor strengthened to 2,2 kW,, 2 Machine lights 12 V,, Optical linear scale with digital display counter (0,001 mm) X, Z Axes,, 2/3” TV Camera with 19” LCD monitor (microscope with zoom 15‐70X included),, High performance swivelling angle reader (0,05°),, Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm,, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm,, Stepless oscillation speed,, Automatic central lubrication,, SIC Wheel dresser manual,, Protection cover., Specifications: Wheel spindle taper: HSK50E (alternatives possibl ...

control: MAZAK Mazatrol 640T Nexus swing over bed: 610 mm swing diameter over bed slide: 350 mm turning length: 982 mm c-axis: indexing: 0.001 ° turning speeds: 4000 U/min tool taper: ASA A2-8 tailstock quill taper MT: 5 rapid traverse X-axis: 30 m/min rapid traverse Z-axis: 33 m/min Overall size: 4500 x 2000 x 1600 mm weight of the machine ca.: 6.5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 400 mm centre height: 195 mm turning diameter over slide rest: 246 mm turning length: 650 mm spindle turning speed - stepless: 0-2500 U/min total power requirement: 7,5 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 2x1.3x1.6 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Sumbel Enano 250 banding machine; cleaned and tested; Working width 250mm; suitable for cold glue; was overhauled in 2010. Gluing machine Sumbel Enano 250; cleaned and checked; woking width 250mm; used for cold glue; Rebuilt in 2010.

Rheinmetall axle Verse No: 2520-12-341-1309 TKZ : 2300002-100 220 000

Linear weigher with 100g up to 10,000g weighing range. Weighing/dosing of granular and chunky products. 2 weighing heads with load cells and 2 vibrating feeders allow fast and precision weighing. - Specifications: capacity weighing hopper: 20 L | number of weighing heads: 2 | weighing range: 100-10,000g | accuracy: +/- 1-25g | max. speed of the machine in neutral: 20 cycles/minute | power: 220V, 1-phase | stainless steel version SUS 304. That machine/system is available in different versions for different packaging sizes and with different packaging speeds. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo a ...

Very large linear weigher for high volume weighing with 1 head. - Specifications: weighing range: 5-25kg | max. speed of the machine in neutral: 10 cycles/minute | accuracy: 0.2% (depending on product) | power: 2.0kW | machine dimensions: L3000xW2800xH4200mm (including 1400mm standing frame/can be customized) | weight: 1500kg. That machine/system is available in different versions for different packaging sizes and with different packaging speeds. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.

; Gross weight [kg]: 5230; Engine: Perkins 2506A-E15TAG1; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 775

We currently offer: Number 001 Generator set Type: IL 250-4 Engine Iveco Generator LeRoy Somer Power: 250 KVA Year of construction 2002 Hz 50 IP 23 AVR Regulator R448 Hours 299 Metrics: L: 5.10m H: 1.90m B: 1.00m Weight: 2800 kg Accessories: Control cabinet You can find more machines on our website. If you have any further questions, please feel free to contact us. Adel e.K. Commercial Vehicles-Construction Machines Car Recycling Machine Dismantling Gottlieb-Daimler Str. 26 D-74831 Gundelsheim Phone: 0049 1796710242

; Gross weight [kg]: 350; Engine: Kubota D722; Accessories: Tanker, Battery, Control Panel, Stahldach, Including: battery charger, 3-way valve, Output sockets: 63A - 16A; Water Tank Volume [l]: 58

; Gross weight [kg]: 345; Engine: Kubota D722; Accessories: Tanker, Battery, Control Panel, Stahldach, Including: battery charger and earth pin, Sockets: (3P) 16A - (2P) 16A - Schuko, 230V/400V; Water Tank Volume [l]: 25

Manufacturer: Sysmex Model: CS 2500 Year of Manufacture: 2012 The CS-2500 is a fully automated, high-performance hemostasis analyzer designed for advanced laboratory needs. Utilizing multi-wavelength technology and PSI™ checks, it delivers precise results for coagulation, chromogenic, immunoturbidimetric, and aggregation testing—all in full random access. Compact and efficient, this benchtop system is an ideal solution for mid- to high-volume laboratories. Find more here - .ucymachines/ Contact us at - sales@ucymachines

This AMADA AC2510 NT + MP 250 was manufactured in 2009. It features a 51-station turret and can handle sheet sizes up to 1270 × 5000 mm, with a maximum thickness of 3.2 mm for mild steel. The machine includes a loading system MP 250, enhancing its efficiency. Consider the opportunity to buy this AMADA AC2510 NT + MP 250 CNC punching machine. Contact us for more information.