127,270 used machines on RESALE, but how to find them? Machine Search
: 95 mm Shaft diameter: 30 mm Shaft revolutions: 7 U/min roll diameter: 132 mm Drive: 0,75 kW weight: 220 kg range L-W-H: 530x900x660 mm Equipment / Accessories: - Two driven rollers with grooved surface - Manual feed of the upper roller - working position horizontal and vertical (with tilting base) - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm I-beam section - upend: 50 x 15 mm roll diameter: 157 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1050 mm plate thickness: 1 mm roll diameter: 56 mm dimensions of the machine ca.: 1600 x 700 x 1050 mm Domestic equipments: - Upper roller can be swung out manually The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Flame cutting machine, torch, oxy-fuel cutting machine -Shaft diameter: 28mm - Shaft length: 200mm - Rack length: 140 mm -Total length: 320mm -Socket diameter: 42 mm -Weight: 2 kg
Spray machine -Closing force: 25 tons -Screw diameter: 22 mm -Unilog 2040 control unit -Slat spacing: 250x250 mm -Data collection terminal -Parts removal device, manufacturer ASS -Temperature control unit, manufacturer Single
Inert gas welding machine, arc welding system, MIG/MAG welding system -Manufacturer: Ess, inert gas welding machine MIG-MAG 520-2 MW -Type: 520-2MW -Max. Welding power: 500 A -Water cooled -Wire feed case: ESS DVK 17 -Dimensions: 1160/500/H1220 mm -Weight: 379 kg
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2100 mm plate thickness: 13 mm pre-bending: 10 mm upper roll diameter: 230 mm lower roll diameter: 210 mm side roll diameter: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 4.620 kg dimensions of the machine ca.: 4150x1400x1300 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG ...
: 80 mm roll diameter: 260 mm : 7 U/min : 170 mm : 27 kN : 160 mm : 450 mm total power requirement: 3,7 kW dimensions: 980x1430x1600 mm weight: 1380 kg Accessories / equipment: - Three driven rollers with a smooth surface - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can bend different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: R10-R260 : 210 ° bending speed: 2 U/min : 1 1/4 x 3,5 mm : einphasig - 230 V drive motor: 1,1 kW : < 70 dB weight of the machine ca.: 80 kg dimensions of the machine ca.: 410 x 1000 x 570 mm Accessories / equipment: Hard copper and aluminum: 54x2 mm Steel tube: 42x3 mm Stainless steel: 42x2.5 mm Solid material: 30 mm Number of programs: 30 each 9 bends Control: Soft-touch control panel in 8 different languages Mobile by driving device The controller allows easy programming of the automatic cycle The controller is equipped with a system diagnostics and has a great language selection. Patented fast tool change system A single bending speed The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inert gas welding machine, arc welding system, MIG/MAG welding system -Manufacturer: Ess, inert gas welding machine MIG-MAG type 310 MW -Max. Welding power: 310 A -Water cooled -Wire feeder: ESS PS 12-8 -Accessories: including hose package, ground cable -Dimensions: 1020/480/H910 mm -Weight: 208 kg
Lid folding machine, folding machine, folding machine, lid folding machine, can folding machine, can folding machine -Lid seaming machine for sheet metal buckets -The machine creates the fold for the lid -Dimensions: 1000/1200/H1150 mm -Weight: approx. 800 kg
plate thickness: 1,25 mm roll-body distance: 250 mm throat: 260 mm distance between roll centers: 62 mm tool adaptor: 26 mm speed: 6,3 m/min total power requirement: 0,7 kW weight: 170 kg range L-W-H: 1020x600x1500 mm Domestic equipments: - motor driven beading machine - 5 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 48x3,5 mm : 48x2,5 mm : 32 mm : 64x2 mm bending speed: 2 U/min : R10-R300 total power requirement: 1,5 kW weight of the machine ca.: 110 kg dimensions of the machine ca.: 410x1000x570 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding band dimension: 150 x 2000 mm band speed: 33 m/sec weight of the machine ca.: 105 kg engine output: 4 kW turning speeds: 2800 U/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 2000 mm band length: 75 mm band speed: 16,5/33 m/s turning speeds: 1400/2800 U/min weight of the machine ca.: 75 kg Volume: 83 dB The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Machine light, machine lamp, workspace light, recessed light -Manufacturer: SBF, recessed light 24V / 7W unused -Type: P002800 -Connection: LED plug -Quantity: 24x lights available -Price per piece -Dimension: 730/45/H37 mm -Weight: 0.7 kg/piece
Machine vice, stable vice, drill press vice -Machine vice: clamping jaws 150 x 50 mm -Clamping depth: 143 mm -Groove: 104 x 17 mm -Dimensions: 455/170/H125mm -Weight: 25 kg
Machine reamers, reamer, reaming tool, fitting knife cutting set -Machine reamer: Shell reamer with holder -Diameter: Ø 26 mm -Shaft diameter: Ø 16 mm -Total dimensions: Ø 25 x 120 mm -Weight: 0.3 kg
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW range L-W-H: 1100x850x1350 mm weight: 495 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - Footswitch - standard roller set The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding band dimension: 150 x 2000 mm band speed: 33 m/sek. total power requirement: 3 kW weight of the machine ca.: 95 kg turning speeds: 2800 U/min Standard equipment: - Removable dust catcher - Fine adjustment of the band adjustment - Sanding belt - Eye protection - Motor protection switch - Operation manual - Sanding table - working height adjustment - surface grinding pad The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
welding rectifier, electrode welding device, electrode welding machine, electrode welding rectifier -Manufacturer: ESAB, welding rectifier type LHE 260 -Welding power: max. 260 A -Welding cable with electrode clamp -ground cable -Dimensions: 710/480/H865 mm -Weight: 119 kg
machine spirit level, block spirit level, frame spirit level, spirit level, precision spirit level, frame spirit level -Machine spirit level: frame spirit level -Frame size: 150 x 30 mm -Reading: 0.3 mm/m -Dimensions box: 195/195/H55 mm -Weight: 1.7 kg
machine vice, stable vice, drill press vice, drilling vice -Manufacturer: Fortis, machine vice type Q94160 -Clamping jaws: 160 x 40 mm -Clamping depth: 205 mm -Dimensions: 405/160/H115 mm -Weight: 28.5 kg
band speed: 33 m/s grinding band dimension: 75 x 2000 mm total power requirement: 3 kW weight of the machine ca.: 75 kg turning speeds: 2800 U/min Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 2,5 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 92 mm tool adaptor: 35 mm speed: 3,5 m/min total power requirement: 1,5 kW weight of the machine ca.: 295 kg dimensions of the machine ca.: 1200x700x1200 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 150 mm band length: 2000 mm band speed: 16,5/33 m/sec total power requirement: 2,6/3,37 kW turning speeds: 1400/2800 U/min weight of the machine ca.: 95 kg Equipment / Accessories: - Removable dust catcher - Fine adjustment of the band adjustment - Sanding belt - Eye protection - Motor protection switch - Operation manual - Sanding table - working height adjustment - surface grinding pad The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW range L-W-H: 900 x 600 x 1000 mm weight: 470 kg connected load: 400/50 V/Hz Equipment / Accessories: - Three driven rollers - Manual delivery of the upper roller - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping table, clamping angle, T-slot table, rotary table, milling machine table -Clamping table: Milling machine table swiveling -Axles: adjustable with hand crank, see photos -Dimensions total: 530/350/H450 mm -Weight: 56 kg
Pressing pliers, pressing machine, pressing jaws, pressing tool -Manufacturer: Roller, press machine type 5788001 with accessories -Pressing pliers: size M15, M18, M22, M28 -Accessories: see photos -Dimensions case: 510/300/H120 mm -Weight: 11.7 kg
ring cutting machine, cutting device, cutting pliers, cutting machine, ring, disc, segment and strip cutting machine, ring cutting machine -Manufacturer: Klinger, ring cutting machine -Cutting range: 80 - 1250 mm -Cutting thickness: up to 9 mm -Dimensions total 1100/170/H280 mm -Weight: 6.4 kg
plate thickness: 4 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 132 mm tool adaptor: 40 mm speed: 5 m/min total power requirement: 2,2 kW weight of the machine ca.: 350 kg dimensions of the machine ca.: 1650x700x1280 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
shaft diameter: 60 mm Shaft revolutions: 6 U/min roll diameter: 215 mm pressure hydraulic cylinder: 180 kN dimensions: 1125x870x1620 mm weight: 820 kg Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1050 mm plate thickness: 3,3 mm pre-bending: 3,0 mm roll diameter: 90 mm min. dia.: 130 mm total power requirement: 1,1 kw weight of the machine ca.: 570 kg dimensions of the machine ca.: 2100 x 800 x 1130 mm Domestic equipments: - Asymmetrical 3-roll round bending machine with motor drive - Upper roller swung out - Conical bending device - Main engine with brake device Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sanding belt width: 150 mm sanding belt length: 2000 mm band speed: 16,5/33 m/sec engine output: 2,6/3,37 kW Motor speed: 1400/2800 UpM weight of the machine ca.: 105 kg Domestic equipments: - vibration-free running smoothness - Working height adjustable - S1 motors with 100% duty cycle - Surface and contact grinding is possible - Removable protective cover for surface grinding - Connecting piece for double suction - Built to CE standard The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
machine vice, stable vice, drill press vice -Machine vice: clamping jaws 175 x 50 mm -Clamping depth: 125 mm -Dimensions: 520/200/H125 mm -Weight: 44.7 kg
continuous welding machine, film welding machine -Manufacturer: Rische, continuous welding machine film welding machine Polystar -Type: Polystar 350/5 DSM-TE -Voltage: 220 V -Technical data: see photo type plate -Dimensions: 520/250/H5600 mm -Weight: 12.1 kg
Counterholder, counter bearing, bearing block, pillow block, bearing for milling machine -Counter bearing: for milling machine -Bore: Ø 32 mm -Guide carriage: 90 mm movable -Dimensions: 400/235/H200 mm -Weight: 33 kg
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW weight: 495 kg range L-W-H: 1100x850x1100 mm Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1250 mm plate thickness: 5,5 mm pre-bending: 5,0 mm roll length: 1280 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1365 kg range L-W-H: 2.020 x 900 x 1.200 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 63x4,2 mm external diameter: min. Ø 5 mm bending radius min.: 10 mm bending radius max.: 270 mm Bending Angle: max. 210 ° bending device: gegen Uhrzeigersinn total power requirement: 0,75 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 740x470x1030 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 215 mm shaft diameter: 60 mm Shaft revolutions: 6 U/min : 100x2 mm : 80x15 mm pressure hydraulic cylinder: 180 kN total power requirement: 2,2 kW weight: 720 kg dimensions: 1200x900x1700 mm Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
machine stairs, machine access, machine platform -Machine platform: solid design -Platform: length 1950 mm with cutout 530 x 410 mm -Height: 520 mm -Dimensions total: 1950/1310/H520 mm -Weight: 105 kg
Cup hinge drilling machine -Stops: pneumatically controlled with program selection -Drilling pattern: see the pictures -Dimensions: 4000/1100/H1800 mm
Machine stairs, machine access, machine platform -Machine platform: solid construction -Platform: 2455 x 1925 mm with cutout dimensions, see photos -Height: 270 mm, additional height 300 mm -Transport dimensions: 2455/1925/H330 mm -Weight: 160 kg
Double bench grinder, double grinding machine, pedestal grinder, pedestal grinder -Manufacturer: Greif, double grinding wheel type D 20/4 -Grinding discs: max. Ø 250 mm -Motor power: 0.37 kW -Speed: 1400 rpm -Operating voltage: 220/380 volts -Dimensions: 500/310/H315 mm -Weight: 40 kg
maximum number of results exceeded
please refine your search
