135,484 used machines on RESALE, but how to find them? Machine Search
width of the strips: 75 mm band length: 2000 mm band speed: 37 m/sec total power requirement: 3 kW weight of the machine ca.: 0,105 t dimensions of the machine ca.: 1,2 x 0,5 x 1,0 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Counting and banding machine ATS US 2000 FSB-DBN-T; State as is; should be installed by ATS Customer Service; suitable for processing banknotes; Rontech MF-360 RAV counting feeder; 1x Banderolier ATS US 2000 AD bandwidth 40mm and frame 260x260mm; 1x Banderolier ATS US 2000 AD Bandwidth 30mmund Frame 260x120mm; Turning unit installed. Count and banding machine ATS US 2000 FSB-DBN-T; condition as is; should be installed by the support of ATS; used for banknotes; count feeder Rontech MF-360 RAV; 1x banding machine ATS US 2000 AD with band width 40mm and frame 260x260mm; 1x banding machine ATS US 2000 AD with band width 30mm and frame 260x120mm; turning station.
width of the strips: 25 mm band length: 762 mm dimensions of grinding wheel: 125 mm Table tiltable up to: 45 Grad table surface area: 130 x 130 mm connected load frequency: 230 V total power requirement: 0,3 kW weight of the machine ca.: 9 Kg dimensions of the machine ca.: 650 x 360 x 400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
faceplate diameter: 3200 mm swing diameter: 3500 mm turning height: 2200 mm Control: Typ 840 D sl total power requirement: 51 kW weight of the machine ca.: 86 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Kammerofen-Anlage für Aluminium Kammerofen-Anlage für Aluminium für den universellen Einsatz wird für die komplette Bandbreite des Aluminium-Glühens konzipiert. Kammerofen zum Glühen von Al-Folienbunden Bunde nach dem Glühen, temperaturgesteuert im fen abgekühlt. Bei Mehr-Kammeröfen und größeren Durchsätzen erfolgt die gesteuerte Abkühlung in einer hierfür vorgesehenen separaten Kammer. H erdwagenofen Rolleherdofen Kammero fen Drehtellerofen Wag enherdofen & Tunnelofen Haubenoen Schach tofen Sonderanlagen Leichtmetall-Folienbunde werden in 1 -Kammer- und Mehrkammeröfen, elektrisch und Gas beheizt, geglüht. Die Öfen werden mit Luftumwälzung versehen, die eine konvektive Erwärmung des empfindlichen Materials gewährleistet. Die Folienbunde werden so in Gestellen angeordnet, dass eine gleichmäßige Durchströmung des Nutzraumes gegeben ist. Die Gestelle werden mi ...
width of the strips: 100 mm band length: 1220 mm band speed: 1140 m/min. : 0,62 x 0,4 x 0,35 cm total power requirement: 1,5 kW weight of the machine ca.: 0,04 t dimensions: 0,97 x 0,67 x 0,37 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 800 mm y-travel: 500 mm z-travel: mm Control: Heidenhain tool taper: SK 40 : 13,5 kw turning speeds: 3150 U/min total power requirement: kW weight of the machine ca.: 3 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter: 630 mm turning length: 2000 mm control: Zyklen gesteuert steady: 2 Stk. total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 600 mm y-travel: 400 mm z-travel: 420 mm Control: Heidenhain Tnc table-size: 900 x 460 mm turning speeds: 4000 U/min total power requirement: kW weight of the machine ca.: 2,9 t dimensions of the machine ca.: 3 x 2 x 2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 700 kN injection volume: 103 cm³ screw diameter: 30 mm platen size: 432 x 310 mm closing stroke: 650 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CNC Lathe Manufacturer: Gildemeister Type: CTX 410 V3 Machine No.: 0136004581 Year of Make: 2006 Control: Siemens 840D ShopTurn Circumferential diameter: 505 mm Chuck diameter: 210 Spindle passage: 65 mm Drive power: 40/ 100%ED 21/28 KW Speed range from – to: 25-5000 Dimensions approx.: 4300x2000x1800 Weight approx.: 5600 Kg - 12-speed revolver - VDI 40 - C-axis - Powered tools 12 stations - Package bar machining - Chip conveyors - Tailstock - SMW Autoblok 210BB - Driven tool holders 3x axial - Driven tool holders 2x radial - Various other tool holders - New engine for revolver Errors excepted
clamping force: -- kN injection volume: 230 cm³ screw diameter: 40 mm platen size: 475 x 475 mm Condition: used, Specification: Horizontal injection moulding machine, injection unit: - Screw diameter: 40 mm - Cylinder diameter: 40 mm - Spraying volume: 230 cm³. Clamping unit: - tie bar distance: 475 x 475 mm - Operating hours approx.: 30000 h - Air valve - Core pull - 12-way hot runner controller The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 4200 kN injection volume: 572 - 1716 cm³ screw diameter: 90 mm platen size: 1040 x 1040 mm closing stroke: 620 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: -- mm cross-section heigth:: -- mm feed:: -- mm speed of feed:: 0,4 - 20 m/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 85 mm cross-section heigth:: 25 - 40 mm feed:: 1 - 999,999,9 mm speed of feed:: 60 m/min cuts max.:: 100 - 120 Schnitte/m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
BÜHLER ECOLINE S PRO 34 die casting machine was built in 2018 in Switzerland by Bühler AG. The machine was used occasionally and is in very good technical condition. The BÜHLER ECOLINE S PRO 34 is designed for the die-casting of aluminium alloy components. It enables the efficient, mass production of aluminium castings used, among others, in the automotive, electronics and machinery industries. In the die-casting process, liquid aluminium is injected under high pressure into a closed die. Once the die is filled, the material cools and precisely takes on the die’s shape. The combination of this technology with a high clamping force of 336 tonnes enables the production of repeatable castings with even the most complex geometries. The BÜHLER ECOLINE cold-chamber die-casting machine is part of a complete production line designed for aluminium die-casting. It includes an ABSOLENT ...
Manufacturer: AWEMA AG Model / Type: UDM111Pos1+5 Type of machine: Universal Depositing Machine with One-Shot technology Year of manufacture: 2009 Capacity: Up to 800 kg per hour, depending on product type and mass viscosity Voltage: 3x400N+V+PE Frequency: 50 Hz Power: 9000 VA Find more here - .ucymachines/ Contact us at - sales@ucymachines
cross-section width:: 5 Schläuche 3-5 mm cross-section heigth:: 3 - 20 mm feed:: 1,5 - 50 mm Condition: used, very good condition only approx. 1 year in production Specification: circular knife cutting machine for slices and rings - small cutting machine with high-speed rotating circular knife - feed and knife movement, pneumatic - Tube or strand diameter min.: 3 mm - Tube or strand diameter min.: 20 mm - Feed (ring or strand length): 1.5 - 50 mm - Output depending on material max.: 60 strokes/min - Optionally, the following can be cut 5 tubes or strands: diameter 3 mm to 5 mm 4 tubes or strands: diameter 5 mm to 7 mm 3 hoses or strands: diameter 7 mm to 12 mm 2 hoses or strands: diameter 12 mm to 15 mm 1 hose or string: diameter 15 mm to 20 mm - Power requirement approx.: 0.37 kW - Air supply min.: ...
: 0 bore depth: 10000 mm number of spindles: 0 Control: Siemens Simatic Touch SPS swing over bed: 1050 mm swing diameter over bed slide: 1600 mm boring diameter: 50 - 310 mm centre height: 800 mm speeds:: 2,5 - 400 total power requirement: 74 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 2650x950x1850 mm Weight: 2100 kg Total power requirement: 15 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 275 mm gear width: 55 mm max. module: 6 min. module: 1,5 control: Sinumerik 840C tooth width: 5,5 mm spiral angle: 0/60 ° max. number of teeth: 120 min. number of teeth: 5 transmission ratio max.: 1:10 transmission ratio min.: 1:1 spindle speeds: max. 110 mm blade head turning speeds: 20-110 1/min total power requirement: 100 kW weight of the machine ca.: 16700 kg dimensions of the machine ca.: 5200x2300x2400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 23 / 28 mm throat: 260 mm bore stroke: 120 mm tool taper: MK 3 table-size: 500 x 350 mm column diameter: 100 mm total power requirement: 1,3 kW weight of the machine ca.: 400 kg dimensions of the machine ca.: 800 x 600 x 1750 mm Defective feed! Right-left rotation stepless speed adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: siehe TD mm pressure: siehe TD t total power requirement: 4 kW weight of the machine ca.: 0,950 t dimensions of the machine ca.: 900 x 1050 x 1300mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
LM 175 S solvent cleaning machine was built in 2000 in Italy by AMA UNIVERSAL. The machine is used for the effective removal of oil, grease and other contaminants from workpieces, machine parts and tools. Cleaning takes place inside a closed work chamber using perchloroethylene (PER). A basket with dimensions of 550 x 300 x 300 mm and a load capacity of 80 kg enables cleaning of a larger number of parts. Once the cycle is complete, the used solvent is fed into the filtration and distillation system, where it is cleaned and prepared for reuse. This solution reduces the consumption of the cleaning medium and helps to lower the machine’s operating costs. The LM 175 S is also equipped with an ultrasonic cleaning system with a power of 1200 W and a frequency of 23000 Hz. The use of ultrasonics helps to remove contaminants even from hard-to-reach surfaces, including holes, gaps and variou ...
ITF Coclea LC 5/4 rotary drum washer was built in 2006 in Italy by I.T.F. S.r.l. Impianti Trattamenti Finiture. The machine is designed to clean large quantities of very small metal parts that are contaminated with oils, greases, emulsions or other contaminants. Cleaning takes place inside a rotating drum, which ensures that the parts are constantly in motion. As a result, all surfaces of the parts are evenly exposed to the cleaning agent, enabling the effective removal of contaminants even from hard-to-reach places. The Coclea LC 5/4 rotary drum parts washer is used in manufacturing plants and wherever the rapid, effective and repeatable cleaning of large numbers of parts is essential. Technical specifications of the ITF Coclea LC 5/4 rotary drum washer - compressed air pressure: 6 bar - control voltage: 24 VAC - power supply of the ITF machine: 3x 400 V
CHMER GX430L+ wire EDM was built in 2018 in Taiwan by CHING HUNG MACHINERY & ELECTRIC INDUSTRIAL CO., LTD. The machine is designed for the precision machining of workpieces using the electrical discharge machining. This technology enables the creation of complex shapes even in the hardest materials, whilst maintaining high dimensional accuracy and excellent surface quality. As a result, the wire EDM is ideal for the production of precision dies, cutting dies, punches and other parts that require high accuracy. The CHMER GX430L+ performs machining with a cutting head that moves in 5 axes. The X and Y axes are driven by linear motors, whilst the Z, U and V axes are equipped with precision servo drives and AC motors. This solution ensures smooth movement of the head, high positioning accuracy and stable operation even under intensive use. The automatic wire threading system reduces the t ...
We are pleased to offer for sale a complete high-precision manufacturing cell designed for the production of long, helical and screw-profile components, including PCP and mud motor rotors, extruder and injection molding screws, compressor and pump spindles. The equipment includes: 1. 2008 LEISTRITZ PW190.8000.HP Peeling / Whirling — Fully Operational Capacity: 120 mm (4.72”) diameter × 8,000 mm (315”) length Machine weight: 92,594 lbs (42,000 kg) 2. 2011 LEISTRITZ LWN300 Milling / Hobbing — Fully Operational 3. 2009 LEISTRITZ PW300PM Milling / Hobbing — Not in Service 4. 2014 WEINGÄRTNER FINISH 450 Finishing / Polishing — Fully Operational This equipment forms a comprehensive production route covering roughing, profile machining, semi-finishing and final surface finishing of long, high-precision helical and screw-profile components. Typical applic ...
Manufacturer GER Model SR150-60 CNC Year 2007 FAGOR 8055i CNC Fixing area on table 1,800 x 550 mm Useful ground surface 1,500 x 680 mm. Longitudinal travel of the table 1,660 mm. Maximum weight on the table 1,700 kg. Automatic cross travel 600 mm. Max. distance from table to center of wheel 625 mm. Variable infinite table speed 2-28 m/min. Cross-table speed 0.02 – 5 m/min Vertical table speed 0.02 – 2 m/min Infinite table speed regulation INCLUDED Maximum width to be ground with a grinding wheel of 80 mm 680 mm. Minimum CNC programmable increment 0.001 mm Spindle speed 1,500 rpm Main motor power spindle 12 kW Total machine power 22 kW Wheel dimensions Ø 400x80x127mm. FAGOR 3-Axis Servo Motors and Regulators (X, Y, Z) included High-density electromagnetic plate INCLUDED Dimensions of the electromagnetic plate 1,500 x 600 mm. Coolant Filtration Equipmen ...
Machine : Rigid angle tables for milling machines Make : EMCO unused – slight traces of storage Clamping surface : 600x200mm, 4 T-slots 12mm, spacing 45mm Vertical: Hole spacing: 90mm/390mm, for T-slot 12mm Dimensions: Length : 60cm ; Width : 20 ; Height : 18cm; Weight: 44 kg PRICE : € 480,- Even larger MAHO or lids, ... Mounting plates: A - Length : 240mm ; Width : 120mm ; Height : 35; 3 T-slots 11mm spacing 45mm, (1x) PRICE : € 100,- B - Length : 420mm ; Width : 125mm ; Height : 46; 2 T-slots 11mm Distance 90mm (4x) PRICE : € 100,- C - Length : 520mm ; Width : 180mm ; Height : 56; 3 T-slots 12mm Distance 45mm (1x) PRICE : € 150,- D - Length : 600mm (660); Width : 180mm ; Height : 75; 2 T-slots 12mm Distance 90mm (3x) PRICE : € 180,-
AGIE AGIETRON HYPERSPARK 2 HS die-sinking EDM machine was built in 2008 in Switzerland by AGIE SA. The machine is designed for the production of precision dies, punching dies, punches and other elements with complex geometry using the electrical erosion. This technology enables the machining of workpieces made from difficult-to-machine and hardened materials, and also reduces or completely eliminates the need for further finishing operations, such as polishing. Electrical discharge machining is performed in a tank filled with a dielectric fluid, which affects the surface quality and dimensional accuracy of the machined workpieces. All process parameters are entered in an intuitive CNC controller, which facilitates the daily operation of the machine. The AGIE AGIETRON HYPERSPARK 2 HS sinker EDM is offered with tooling. The total weight of the EDM machine is 2800 kg. Technical specifica ...
x-travel: 550 mm y-travel: 1200 mm z-travel: 450 mm control: 85er 8bit total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Bang & Co SAP 603 strapping machine – built in 2016 – fully functional + 2 rolls of tape Sell a used, fully functional Bang & Co strapping machine model SAP 603. Nameplate): • Model: SAP 603 • Machine No.: 15015642 106 • Year of construction: 2016 • Power connection: 230 V / 50 Hz • Manufacturer: Bang & Co GmbH, Oberursel • CE marking available Condition & Scope of Delivery: • Fully functional and ready to use • Good used condition • Also included: 2 rolls of strapping Ideal for commercial use for secure strapping of cartons, parcels and packages. Sale: • Delivery possible • Pick-up available If you are interested, please contact us - more photos/videos or a demonstration on site are possible.
Double pump for Krauss Maffei machines Voith Rexroth control pumps 3-fold SY2DFE1-21/071-071 KM No. 6441936 MNR: R900751978
Specifications: - Drilling capacity in steel ST 60 30 mm - Drilling spindle holder MK 3 - 4 feeds 0.1 - 0.16 - 0.25 - 0.4 mm/U - Drilling spindle speeds in gear stages 95 - 2000 rpm - Right - Left - Drilling spindle stroke 160 mm - Projection 350 mm - Table with 3 T-slots height-adjustable 340 x 320 mm - Table can be tilted left + right - distance table – drilling spindle 500 mm - distance machined base plate – drilling spindle 1050 mm - Column diameter 160 mm - Lighting - Coolant device - Drive 400 V / 2.4 kW - Space requirement approx. W 600 x H 1950 x D 800 mm - Weight approx. 350 kg
brand: CKD BLANSKO Model: SKHK 50 plateau diameter: 4770 mm maximum diameter: 5200 mm ram stroke: 2000 mm maximum height: 3000 mm capacity: 50 ton. Plateau revolutions: 1 range: 0.4-12/ 2 range: 1.6-50
With matching spacer rings according to photos. Scope of delivery according to photo 1.
Manufacturer MORI SEIKI Model NL3000/3000 Year 2.008 CNC MORI SEIKI MSX-850III Capabilities and advances Max. turning on bed 995 mm. Max. turning on transverse carriage 825 mm. Maximum turnable diameter 420 mm Maximum turnable length 3,123 mm. Distance between points 3,200 mm. X-axis travels 280 Z-axis travel 3,170 mm. Fast Forward X-Axis, Z 30.0000 mm/min Head Nose head JIS A2-8 Maximum head speed 3,000 rpm Rod pitch head 105 mm. Axle diameter in the front bearing 160 mm. Main motor power 28 kW Maximum torque 3,365 Nm Turret No. Turret 12 Positions Maximum square tool size 25 mm Bored bar diameter 50 mm. Turret indexing time 0.3 s Counterpoint Tailstock travel 3,164 mm Tailstock shank diameter 150 mm Tailstock shaft course 150 mm MT5 tailstock cone Equipment 3 Claws Hydraulic Plate Ø 400 mm INCLUDED Chainring type SCHUNK THW 400-120 Quick C ...
Used flow pack packaging machine. Manufacturer Chemosvit Strojchem, model BH-07W. New 2017. Capacity 15-250 pcs/min. Available 3 pcs. (2 used and 1 almost unused)
x-travel: 3500 mm y-travel: 900 mm z-travel: 1000 mm Control: heidenhain tnc 415B total power requirement: 22 /spindel kW weight of the machine ca.: 16.5 t dimensions of the machine ca.: 7.2x3.9x3.2 m Make SORALUCE Type Soramill SL 5000 Built in 1995 Control type HEIDENHAIN TNC 415 B Table size (mm) 5000 x 800 mm X out (mm) 3500 Y-off (mm) 900 Z-off (mm) 1000 Maximum table load 12,5 ton Speed (RPM) 20-. 2,000 Tool holder ISO 50 Feed along (mm/Rev) 5 - 10000 mm / min. Rapid traverse 12 mtr/min. Gesamtleistung(kW) 22 Length (mm) 7250 Width (mm) 3900 Height (mm) 3200 Weight 16500 kg Additional information Automatically indexierender Swivel Head with 2 x 144 positions (2.5 ° pitch) in two levels above the control programmable Cooling medium institution The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
1 of used carton erector with bottom sealer, make STORK, type SA-25L (KOALA), new 1989, size adjustable. With Siemens S5-100U PLC, Nordson 2302 hot-melt unit and blank feed conveyor. Left to right as seen from operator’s side. Capacity maximum 25 cartons/minute (depending on size). Carton dimensions: length: 150 - 450 mm, width: 100 - 400 mm, height: 180 - 400 mm. Blank dimensions: min 250 x 280 / max 850 x 750 mm. Fully guarded. Manuals available.
maximum number of results exceeded
please refine your search
