sheet bending machine used for sale

DM01 control module for Trumpf Suitable for Trumpf built between 1998 and 2004

TBF controller card Trumpf bending machine suitable for Trumpf bending machine year 1998-2004

Inv. Num. : 8711 Type: MG 2000 x 25/20 Producer: Maqfort Created: 1998, GO 2016 Parameters: Working length rollers: 2000 mm Max. sheet thickness: 25 mm

Bending length / working length 2,500 mm Press force / bending force 1,500 kN (≈ 1500 kN) Max. sheet thickness (steel) approx. 2.0 mm Max. sheet thickness (aluminium) approx. 3.0 mm Max. sheet thickness (stainless steel / higher tensile strength) approx. 1.25 mm Max. bending height approx. 300 mm (depending on model) Power / Capacity (Electrical) 24 kW Machine dimensions: 4,050 × 1,600 × 2,400 mm Weight ~ 13,000 kg

A mandrel tube bending machine Sommer is available. Tube diameter range: 15mm-65mm, tube feed length: 3000mm, max. bending radius: 150mm, chuck: 200mm, tube clamping: hydraulic. Including accessories. Documentation available. An on-site inspection is possible.

Bending capacity: 3/8"-2" Bending angle: 180° Angle turret: 6-fold Mounted bending tool: Ø 28 mm Country of origin: Netherlands Motor power: 3 kW Machine weight: 250 kg Machine LxWxH: 1,000 x 800 x 950 mm

Shaft bottom/top: 30mm/30mm, max. round tube length: 48mm, max. round tube diameter: 3mm, max. flat bar dimensions X/Y: 50mm/10mm, max. square tube dimensions X/Y/Z: 40mm/30mm/3mm, weight: approx. 200kg. Documentation available. An on-site inspection is possible.

Manufacturer: HAEUSLER Model: HPR 330 V+H Year of Manufacture: 2007 Approximately 10 pallets of tools for round bar processing are included, with diameters of 60.5, 137, 91, 168, 76, 51, 152, 129, etc. Condition : Machine currently not in use and therefore not fully assembled Technical Data: - Maximum bending moment (at 240 N/mm² yield strength): 200–330 cm³ - Number of bending rolls: 3 - Roll arrangement: asymmetric / symmetric - Roll diameter: 520 mm - Driven rolls: all 3 - Roll drive: hydraulic - Working speed: 0–7 m/min, stepless - Speed compensation between upper and lower rolls: automatic - Roll rotation reversal: electro-hydraulic - Adjustable bending rolls: 2 - Adjustment of bending rolls: hydraulic - Roll position display: digital, 0.1 mm accuracy - Roll bearings: roller bearings - Number of pressure roller systems: 2 - Adjustment of pressure roller systems: hydrauli ...

A flat steel bending machine for the production of ZB frames is available. Pneumatic pressure: 8bar, hydraulic pressure: 100bar, weight: approx. 5000kg. An on-site inspection is possible.

Inv. Num. : 8806 Type: XZMP 3150/16 Producer: PIESOK Created: 1982 Parameters: Working length rollers: 3150 mm Max. sheet thickness: 16 mm Number of driven rollers: 3 pieces Weight: 40000 kg

Key data: 2540 mm, 8 mm

Max. bending length: 2540 mm Max. sheet thickness: 8 mm steel Upper roller diameter: 200 mm Clockwise and counterclockwise rotation via footswitch Safety rope hoist Conical rounds possible Motorized rear roll infeed Lower roll feed via handwheel with position indicator Weight: approx. 4,500 kg

Bending length: 4200 mm pre-bending: 34 mm Bending strength: 38 mm power capacity: kW Number of rollers: 4 Stk Adjustable rollers: Stk diameter of upper rolls: 540 mm diameter of lower rolls: 500 mm side roll diameter: 365 mm work speed: 0 - 8 m/min total power requirement: 55 kW weight of the machine ca.: 35 t Control: Haeusler Bendtronic 2.0 dimensions of the machine ca.: 7.5 x 2.1 x 2.4 m Equipped with: - Haeusler BENDtronic 2.0 control system - Smallest possible bending diameter with upper roller Ø540mm: 595mm (depending on springback) - Roller bearings: Self-adjusting roller bearings - Max. cylinder force against upper roller: 3,245kN - Roller material: 42CrMo4 (1.7225) - Speed compensation between upper and lower roller: automatic when the two-roller drive option is selected - Roller adjustment: hydraulic - Tilting of the lower roller and both side rollers for cone bending: infini ...

Workforce: 300 kN/30 t Tool height: 200 mm Stroke length: 0 - 300 mm Bending capacity with prism tool MW 125/240: 200 x 16/200 x 24 mm Bending speed: 0 - 1.3 m/min Drive motor: 380 V, 5.5 kW Weight: 800 kg Footprint: 1250 x 820 x 1120 mm

Diameter of bending rollers 550 mm Drive Type Hydraulic Main motor power30 kW

Equipment: 1 pliers feed right 4 Carriage Units Working Range: Wire thickness range: 0.5 - 2.0 mm Band width: up to 10.0 mm Length of move; up to 100 mm Output: up to 300 rpm

Equipment: 1 Carriage Feed Right 1 eccentric press 250 kN 4 normal carriage units 1 narrow carriage unit Working Range: Wire thickness range: up to 6.0 mm Strip width: up to 80 mm Feed length: up to 250 mm Power: 10 - 250 rpm

Equipment: 1 piece BIHLER noise protection cabin 1 piece pliers feed right 1 piece eccentric press 70 kN 4 Norma sled units 1 piece narrow sled unit Working Range: Wire thickness range: 0.5 - 3.5 mm Strap width: up to 32 mm Feed length: up to 170 mm Power: up to 250 rpm

Stock number: 4017 PROFILE BENDING MACHINE Manufacturer: Roundo , Type: R4 Machines NO.: 1735, Year of manufacture: 1977 Specifications: Angle steel 90x9 mm Flat steel 200 x 30 mm Frame steel upright 100 x 18 mm Round steel 60 mm Load by steel 40 Kg/mm2 30 cm3 Upper roller 275 mm Ø Shaft dia. 105 mm Square steel 55 x 55 mm T-steel 90x10 mm Total power 5.5 kW Length: 1500 mm, Height: 1400 mm, Width: 1400 mm, Weight: 2500 kg

A semi-automatic NC tube bending machine Tracto-Technik is available. Tube diameter: 48mm, max. tube length: 3000mm, max. material thickness: 4mm, max. bending angle: 180°, max. bending radius: 125mm, bending accuracy: +/-0.2°, bending speed: 20°/s. Machine dimensions X/Y/Z: approx. 3900mm/800mm/1250mm, weight: approx. 700kg, control system: Siemens Simatic. Documentation available. On-site inspection is possible.

Material width 150 mm, material thickness 0.5 -3.0 mm Colour: green Total power requirement: 380 V Weight: 350 kg Dimensions: 800 x 1200 x 1350 mm Roller diameter: 24 mm Machine number 700257

Key data: 3000 mm, 8 mm

3-roll bending machine / round roller Schäfer SRMVHY – fully functional For sale is a used 3-roll bending machine (round roller / sheet metal bending machine) from the manufacturer Schäfer, model SRMVHY, built in 1992. The machine is in fully functional condition and is ready for immediate use. The rollers are hydraulically adjustable, which allows for precise and comfortable adjustment. The round bending machine is ideal for bending sheet metal in workshops and production plants. Technical data: Manufacturer: Schäfer Model No.: SRMVHY Year of Make: 1992 Max. sheet width: 3,000 mm Max. sheet thickness (mild steel): 8 mm Roller diameter: approx. 200 mm Voltage: 380 V Dimensions (L x W x H): approx. 5,300 x 1,800 x 1,300 mm Condition: used, fully functional Equipment: hydraulically adjustable rollers Changes and errors in the technical data, ...

A CNC flat wire vertical wire bending machine V&C GmbH is available. Wire thickness range: 0.8mm-10mm, max. wire width: 30mm, min. winding inner diameter: 20mm, max. winding outer diameter: 250mm, max. winding height: 160mm, max. winding height with holding rod: 500mm, max. winding length: 250mm, min. bending radius: R6°, max. number of edges: 12/revolution. Machine dimensions X/Y/Z: approx. 2650mm/1000mm/1800mm, weight: approx. 800kg. Documentation available. On-site inspection is possible.

sheet width: 4200 mm plate thickness: 14 mm pre-bending: 10 mm roll diam. toproll: 340 mm roll diam. bottom roll: 310 mm speed: - m/min Control: Davi CNC total power requirement: - kW weight of the machine ca.: 11 t dimensions of the machine ca.: 6,5 x 1,75 x 1,65 m - DAVI CNC control - pre-Bending - Hydraulic 4-roller drive - Side roll diameter: 230 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This AMADA Vipros 255 was manufactured in 2001. It is a used punching and bending machine, ideal for those looking to enhance their metal fabrication capabilities. Contact us for more information about this machine.

plate thickness: 1,7 mm roll diameter: 50 mm Dimensions (L/W/H): 1600 x 600 x 1500 mm weight of the machine ca.: 400 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This Sahinler HKP-Z 100 was manufactured in 2016. A robust C-frame PLC controlled deep drawing press, it features a pressure force of 1000 kN and a stroke of 500 mm. The machine includes a large table size of 900x600 mm and a throat depth of 300 mm, suitable for diverse punching and bending tasks. Consider the opportunity to buy this Sahinler HKP-Z 100 punching and bending machine. Contact us for more information about this machine.

This 6-axis PEDRAZZOLI Bend Master 42 MRV IMS CNC was manufactured in 2001. It features a max tube diameter of 42 mm, a min tube diameter of 6 mm, and a max bending radius of 270 mm. With a power of 22 kW and a bending length up to 3000 mm, consider the opportunity to buy this PEDRAZZOLI Bend Master 42 MRV IMS CNC roll bending machine. Contact us for more information about this machine.

Key data: 3500 mm, 12 mm

Schäfer SVRM 3500/12 - CNC 4-roll bending machine - Siemens CNC control with joystick for roller positioning and digital display (renewed in 2006) - Hydraulic tilting of the upper roller by control panel - Rollers made of quenched and tempered material with a strength of 900 N/mm² - Year of construction 1989 Technical data - Max. sheet width: 3500 mm - Bale length of rollers: 3550 mm - Max. sheet thickness bending: 12 mm - Max. sheet thickness bending 4xS/3xS: 8 / 6 mm - Max. insertion limit of the sheets at 20% work hardening: 380 N/mm² - Upper and lower roller diameter: 360 mm - Side roller diameter: 290 mm - Smallest radius to be achieved: 220 mm - Feed speed lower roller: 200 mm/min - Feed speed side rollers: 700 mm/min - Total installed capacity: 22 kW - electr. Control: 380 V / 50 Hz / 3 Ph - Machine weight: 21100 kg

Offer 26046 Technical data: - 2 mot. Driven rollers - Manual. Lining of the upper roller - Shaft diameter 30 mm - Shaft rotation 6 rpm - Roller diameter 88 - 108 mm - Bending capacity approx. - Flat steel 50 x 8 mm - Square 20 mm - Round tube 42 mm - Drive 380 V / 0.55 kW - with: - Right / left – run - Tube roller set approx. 16 mm - Weight approx. 150 kg - Space requirement approx. W 650 x H 1300 x D 950 mm

Used, technically overhauled reinforcing steel bending machine. 4 pieces of counter retaining strips. 2 footswitches with emergency stop function. Max. bending power 2 rods 28mm D. Bending speed 6/13 revolution.min. Control Siemens Touch Display CC Power 4 KW.

Used, technically overhauled reinforcing steel bending machine. 4 pieces of counter retaining strips. 2 footswitches with emergency stop function. Max. bending capacity 1 rods 28mm D. Bending speed 6/16 revolution.min. Control with bending pins for three angles adjustable by hand. Power 3.5 KW.

Offer 26018 Technical data: - Max. working length 500 mm - Max. sheet thickness 1.5 mm - Various roller diameters - Drive – brake motor 400 V / 1.4 kW - Space requirement approx. W 850 x D 1700 x H 1250 mm - Weight approx. 0.8 t - Roller attachments 42 ; 45 ; 50 ; 55 ; 60 ; 65 ; 70 ; 90 ; 135 mm

Module was changed because a PCSS conversion took place on the machine and therefore this module no longer fits. Fully functional.

Truma Bend V85X 2 meters wide, 2.90 high Year of manufacture 2005 25,000 hours

Trumpf Servo Amplifier New Part

sheet width: 4000 mm plate thickness: 30 / 35 mm pre-bending: 30 mm diameter of upper rolls: 570 mm side roll diameter: 450 mm diameter of lower rolls: 540 mm bending speed: 4 m/min min. bending diameter: 650 mm total power requirement: 60 kW weight of the machine ca.: 52 to dimensions of the machine ca.: - m The machine was overhauled in 2022 Equipment: - Hydraulic 4-roller round bending machine - Roll material: 61 MnCrMo 43 - Driven rolls: 2 Top-and bottom roll -- Drive: over 2 hydro motors direct flanged -- Adjustment speed bottom roll: 0-200 mm/min -- Adjustment speed side rolls: 0-700 mm/min - Speed compensation between top-and bottom roll: automatic - Operation of the tilting bearing: hydraulic - Tilting of the top roll: hydraulic - Bearing block: hydraulic - Indicator device of roll position: digital The data for this ad was created with ModulMWS - the software solution of Logo ...

An asymmetrical three-roll plate bending machine MG is available. Working width: 2000mm, roller diameter: 130mm, max. plate thickness: 3mm, power: 6kW, weight: approx. 2000kg. An on-site inspection is possible.

A four-roll plate bending machine Kramer is available. Working width: 2000mm, max. plate thickness: 3mm, power: 3kW. An on-site inspection is possible.

Roll bending machine manufactured in 2020. This Metallkraft GBP BASIC 26100 features a pressing force of 100 tons and a maximum bending length of 2600 mm. It is equipped with an 11 kW engine and has an oil tank capacity of 150 liters. If you are looking to get high-quality bending capabilities, consider the Metallkraft GBP BASIC 26100 machine we have for sale. Contact us for further details.

4 ROLL HYDRAULIC DUAL PRE-PINCH 3000x15 MM PLATE BENDING MACHINE NEW Brand MG model M3015 -Width of plate 3000 mm -Thickness of plate rolling 15 mm -Thickness of plate pre-bend 12 mm minimum bending diameter ID 350 mm Rolls dimensions: -Surface length mm. 3100 -Top roll mm. 290 -pinch roll mm. 270 -Power electric 10 Hp Technical data: -rolls hardened surface high resistance -variable rolling speed -Powered driven hydraulic rolls rotation -conical bending attachment roller type -calibration system re-rolling welded shells -deflection pinch pressure adjustable upon the thickness -overload protect complete safe operation of the machine. -control console on wheels with electric joysticks commands -position readout digital display for rolling memorize and repeat -safety and emergency systems installed -manuals and schematics along with the machine

Manufacturer: Durma Model: HRB-4 2010 Year of Manufacture: 2012 Type of Machine : 4-roll bending machine Machine Weight: 4,450 kg Condition: Unused - acquired May 2023, never operated, stored in warehouse Technical Specifications: - Bending Length: 2,050 mm - Max. Bending Thickness (mild steel): 8 mm - Max. Bending Capacity: 10 mm - Top Roller Diameter: 210 mm - Lower Roller Diameter: 190 mm - Side Roller Diameter: 180 mm - Min. Rolling Diameter: 30 mm - Motor Power: 11 kW - Oil Tank Capacity: 160 litres - Machine Dimensions (L x W x H): 3,830 x 1,160 x 1,180 mm Find more here - .ucymachines/ Contact us at - sales@ucymachines

Key data: 100 mm, 160 mm, 115 mm

Profile bending machine model PP100 Output shafts 100 mm fully hydraulic operated lower shafts motion independent pyramid pinch -all the 3 shafts driven with gear unit and hydraulic motor -lateral correctors left/right for guiding and align the profile, -Set of rollers complete with extra rollers to seat and bend the various shape of profiles. -7 set of rollers for pipe bending from 1,5” to 4,5” inch ( see photo in enclosed ) -Centralized control panel electric with digital position readout -Safety & emergency installation -voltage 3ph 380/50 -10 Hp -capacity chart in enclosed

Machine Type: Profile Bending Machine Make: COMAC Type: 308 Year of manufacture 2004

tube diameter: 6 - 42 mm wall strength: 3 mm bending radius min.: 180 mm bending radius max.: 5 mm total power requirement: 1,5 kW weight of the machine ca.: 0,8 t dimensions of the machine ca.: m Equipment: Saw unit Notching unit Deburring unit for internal and external edges Flaring unit / flaring function (necking / expanding) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Wire Bending Machine WAFIOS AG BM 30 – 2017 | Very Good Condition For sale: high-class CNC wire bending machine WAFIOS BM 30, year of manufacture 2017. The machine is in very good technical condition, with low operating hours – ready for operation without additional investment. Key parameters: Wire diameter range: 2.0 – 6.5 mm Working range: 600 N/mm²: 2.0 – 6.5 mm 1,200 N/mm²: 2.0 – 4.5 mm 1,900 N/mm²: 2.0 – 4.0 mm Optional: capability to process wire from 1.5 mm Maximum feed speed: 120 m/min Bending torque: approx. 250 Nm Number of CNC axes: 7 Equipment: Decoiler Safety fencing Drive rollers (3 pairs of feed rollers) Functionality and capabilities: Unlimited rotation angle of mandrel axis and bending shaft Precise bending head operation (vertical and lateral movements) Possibility to extend functionality (e.g. CNC support plate) High pro ...

Working range pipe Ø 6 to 42 mm - Bending, deburring, pre-assembly, sawing - Pipe extension length approx. 1,500 mm - Electro-hydraulic drive 1.5 kW - Weight approx. 700 kg - Incl. extensive tools - See photos

Three-roll round, three-roll sheet metal bending machine, bending machine, sheet metal bending machine, 3-roll round bending machine, profile bending machine, three-roll sheet metal rolling machine -Spare part top roller -Drawing with the pictures -Max. Sheet width: 2060 mm -Max. Sheet thickness: mm -Roller diameter: 141 mm -Bearing diameter: 75 mm -Transport dimensions: 2690/141/H141 mm -Weight: 290 kg

Ring bending machine, profile bending machine, bending machine, pipe bending tool, pipe bender, pipe bending machine, mandrel bending machine -Mandrel bending machine: mechanical profile bending machine -Accessories: see photos -Tool: Currently available tools are designed for box profiles -Overall dimensions: 1200/740/H1220 mm -Weight: 169 kg

Three-roll bending machine, three-roll sheet metal bending machine, bending machine, sheet metal bending machine, 3-roll bending machine, profile bending machine, three-roll sheet metal rolling machine, manual bending machine -Roll bending machine: 3-roll roll bending machine, hand-operated -Max. sheet width: 1600 mm -Max. sheet thickness: 2 mm -Roller diameter: 90 mm -Dimensions: 2000/1125/H1370 mm -Weight: 405 kg

Three-roll bending machine, three-roll sheet metal bending machine, bending machine, sheet metal bending machine, 3-roll bending machine, profile bending machine, three-roll sheet metal rolling machine, manual bending machine -Roll bending machine: 3-roll roll bending machine, electrically driven -Bending adjustment: electric -Max. sheet width: 2040 mm -Max. sheet thickness: 4 mm -Roller diameter: 150 mm -Dimensions: 1080/2880/H1370 mm -Weight: 1770 kg