126,710 used machines on RESALE, but how to find them? Machine Search
bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW range L-W-H: 1100x850x1350 mm weight: 495 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - Footswitch - standard roller set The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW range L-W-H: 900 x 600 x 1000 mm weight: 470 kg connected load: 400/50 V/Hz Equipment / Accessories: - Three driven rollers - Manual delivery of the upper roller - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
shaft diameter: 60 mm Shaft revolutions: 6 U/min roll diameter: 215 mm pressure hydraulic cylinder: 180 kN dimensions: 1125x870x1620 mm weight: 820 kg Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW weight: 495 kg range L-W-H: 1100x850x1100 mm Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 63x4,2 mm external diameter: min. Ø 5 mm bending radius min.: 10 mm bending radius max.: 270 mm Bending Angle: max. 210 ° bending device: gegen Uhrzeigersinn total power requirement: 0,75 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 740x470x1030 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 215 mm shaft diameter: 60 mm Shaft revolutions: 6 U/min : 100x2 mm : 80x15 mm pressure hydraulic cylinder: 180 kN total power requirement: 2,2 kW weight: 720 kg dimensions: 1200x900x1700 mm Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 60x3 mm : 60x2,5 mm : 35 mm : 64x4 mm : R10-R300 bending speed: 2 U/min total power requirement: 1,5 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 595x363x900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 200 kN stroke length max.: 200 mm working feed: 10 mm/sec return speed: 20 mm/sec : 480x1060 mm work height max.: 900 mm toolpiece height max.: 200 mm total power requirement: 2,2 kW : 200x12 mm bending capacity max. - round: 48x4,0 mm weight: 500 kg Overall size: 1010x480x1120 mm Domestic equipments: - with semi-automatic control (99 programs with 16 steps each) - including bending bolt (without punch) - Tool holder for dies - Foot pedal Equipment: - Stamp, small U = 145 mm 85 °, H = 200 mm, R = 5 mm - Quick change monometer 85 °, H = 200 mm, V = 63 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Bending tool, die, upper knife, upper tool, upper beam -Tool: for folding machine -Dimensions: 60 x 15 mm -Length: 1020 mm -Weight: 6 kg
Bending tool, die, lower knife, lower tool, lower beam, -Tool: for folding machine -Widening: for lower cheek -Dimensions: 33/76/3040 mm -Bore distance: 280 mm -Hole diameter: 18 mm -Length: 3040 mm -Weight: 33 kg
sheet width: 2020 mm plate thickness: 1,5 mm distance between columns: 2050 mm Daylight opening: 100 mm total power requirement: 0,75 kW weight of the machine ca.: 1 t dimensions of the machine ca.: 2,7 x 1 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 (500) mm : 45 (500) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 80 x 9 (800) mm Axis diameter: 60 mm work speed: 5,0 m/min Tool diameter: 195 mm total power requirement: 3 kW weight of the machine ca.: 1,0 t dimensions of the machine ca.: 1,2 x 0,9 x 1,2 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 76-86 mm Shaft diameter: 20 mm Shaft revolutions: 11 U/min Bending capacity round tube: 30 mm : 25x6 mm Angle iron: 20x20x4 mm Drive: 0,18 kW range L-W-H: 530x420x500 mm weight: 80 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßerb CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines
sheet width: 2020 mm plate thickness: 2 mm distance between columns: 2030 mm bending angle max.: 135 ° total power requirement: - kW weight of the machine ca.: 1,22 t dimensions of the machine ca.: 2,5 x 1,0 x 1,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - upend: 100 x 20 (d 2100) mm tube diameter max.: 100 x 3 (d 3000) mm L-beam: 80 x 80 x 8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm bar material - diameter: 60,0 (d 1000) mm I-beam section - flat steel: 120 x 30 (d 600) max. 140 mm tool taper: 80,0 turning speeds: 4,2 U/min weight: 1600 kg dimensions: 1240 x 1375 x 1540 mm Domestic equipments: - Welded steel structure (St-52) - Rollers are driven by 3 separate hydraulic motors - Stepless speed - Special steel gears - Shafts are made of special steel, hardened and ground - Manual lubrication - Guide rollers are hydraulically adjustable - Lower rollers are hydraulically movable up and down - Infinitely adjustable speed of the lower rollers, move after below and above - Digital display for lower rollers - Separate and movable control panel - Horizontal and vertical operation - Production quality certified according ...
Inv. Num. : 5725 Type: A 89 TNCB Producer: CSM Created: 2014 Parameters: Maximum bending angle: 180 pcs Total power requirement: 15 kW The largest profile: 60x60x6 mm bending radius in the middle of the tube: 350 mm bending radius in the middle of the profile: 300 mm Machine height: 1200 mm Machine length: 4700 mm Machine width: 1200 mm Machine weight: 2500 kg
Reinforcing steel bending machine, shaft bending machine, round steel bending machine -Drive: hydraulic -Power: 4 kW -Bending angle: for left/right to adjust the angle -Equipment: adjustable counter-support strips, standard bending tool -Dimensions: 930/1640/H890 mm -Weight: 1140 kg
Reinforcing steel bending machine, shaft bending machine, round steel bending machine -Drive: hydraulic -Power: 4 kW -Bending angle: for left/right to adjust the angle -Equipment: adjustable counter-support strips, standard bending tool -Dimensions: 930/1640/H890 mm -Weight: 1200 kg
Reinforcing steel bending machine, shaft bending machine, round steel bending machine -Drive: hydraulic -Power: 4 kW -Bending angle: for left/right to adjust the angle -Equipment: adjustable counter-support strips, standard bending tool -Dimensions: 930/1640/H890 mm -Weight: 1200 kg
Unbek. Type, YOC ca. 1990, Revision 2002 Specifications: - Bending capacity at 45 kg / mm² up to approx. Ø 25 x 3 mm - Bending angle left + right selectable - Hydr. Double-sided bending function - Hydr. Delivery ° - Drive 400 V / 11 kW - Space requirement approx. W 1750 x H 2200 x D 2300 mm - Weight approx. 1600 kg - with - bending angle adjustment - Hydr. Voltage - Bending tools
• 3000w IPG with Picking • Sorting Unit LSR & Combo Storage H38 • Large Format 3000 x 1500mm • Year 2014 • Servo Electric - High Speed 30 Ton Punching Head • ONLY 535 HOURS!
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
MEP Multimatic SA8, year of construction 1995 Straightening and cutting system for reinforcing steel, fully automatic, complete functional system, immediately available Plant still in operation and can be demonstrated.
1 Wire bending machine OMCG date 1997 technical status good , soft ware to be refurbished 2.Tube bending machine OMCG date 1998 technical status good, software to be refurbished
Equipment: 1 sledge feeder on the right 3 press modules á 180 kN = 540 kN 4 normal carriage units 1 narrow carriage unit Workspace: Wire thickness range: up to 10 mm Belt width: up to 100 mm Feed length: up to 250 mm Power: up to 132 rpm
Equipment: 1 sledge feeder on the right 1 two-point eccentric press 70 kN 4 normal carriage units 1 narrow carriage unit Workspace: Wire thickness range: up to 3.5 mm Bandwidth: up to 32 mm Feed length: up to 170 mm Power: up to 250 rpm
Equipment: 1 sledge feeder on the right 1 two-point eccentric press 250 kN 4 normal carriage units 1 narrow carriage unit Workspace: Wire thickness range: up to 5.0 mm Belt width: up to 40 mm Feed length: up to 320 mm Power: up to 132 rpm
tube diameter: 50,8 mm wall strength: 1,0 mm square edge steel: 50 x 50 x 1 mm round bar steel: 25 x 6 mm weight of the machine ca.: 46 Kg dimensions: 0,6 x 0,4 x 0,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 kN stroke: 0-200 mm table-size: 450 x 1000 mm working speed:: 6-10 mm/ sec. return speed: 20 mm/sec work height max.: 900 mm toolpiece height max.: 200 mm total power requirement: 1,5 kW bending capacity max. - round: 42x3,2 mm : 150x10 mm weight: 320 kg dimensions: 1010x480x1120 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Brand BENDMAK Type CYL-ST-170-20-5,0 Working lenght 2100 mm Pre-Bending 5 mm Max Thickness 5 mm Top Roll 170 mm Min Bending 255 mm Motor Power 4 kW Bending Speed 4,8 m/min. Dimensions L x W x H 4000 x 1100 x 1130 mm Weight 2300 kg Year 2015 Extra information Cone Bending device Induction hardened rolls Motorized Up and Down movement of the Back Roll Digital readout for Displaying positions of the Back Roll 2 Separte Control Units Cast Iron Body
Trumpf TRUBEND 5085 - WORKING INSIDE PRODUCTION WORKING HORS: PRESENT ON PHOTO OF SCREEN Year 2011 Compression force: 85 tonnes Table length: 2,200 mm Free travel speed: 220 mm/s Accessories: Increased lift height from 230 mm to 615 mm. 5-axis bending. Hydraulic tool clamping at the bottom. Hydraulic tool clamping at top. Automatic bombing. Bendguard guard ACB angle measurement FOR CLIENT WE ORGANIZE AS WELL DISMANTLING AND TRANSPORT
We sell on behalf a pipe and profile bending machine of the company Knuth (type KPB 50 ). The condition is AS NEW and has a lot of accessories. Pictures to follow
Hand bending machine Flat bar 30 x 8 mm Square steel 12 mm Round steel 15 mm Weight 0.025 t Package size max. 51 x 31 x 22 cm Condition: never used / new (5)
Manufacturer: Haeusler Type: VRM HY 4000 x 45 Stock number: 0973 Year of construction: 2001 Bending length: 4000 mm Bending strength: 45 mm Bending (cold): 38 mm Drive power: 100 kW Number of reels: 4 Adjustable rollers: 3 Type of adjustment of the rollers: hydraulic Top roll diameter: 710 mm Underroll diameter: 640 mm Side roller diameter: 520 mm Working speed: 2+4 m/min (up to 8m/min) Machine weight (with roller): 78 t Accessories Electronic synchronization Air-cooled oil cooler Upper support device Side cylinder support device (10t) Inlet table (20t) hydr. Bubble storage Cone bending device
maximum number of results exceeded
please refine your search
100 € 
