shears 3100 used for sale

: neu : ca. 12 Wochen ab Auftrags : 1530 mm : 16 mm : 12 mm : 7 1/min : 3 ° : 8 pcs. : 500 mm : 22.5 kW : 250 l : 950 mm : 2350 mm : 1400 mm : 2000 mm : 5200 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 28 min. Punching force: 110 to : 40x20 mm flat steel: 600x15 oder 400x20 mm L-beam 90°: 160x160x16 mm L-beam 45°: 70x70x7 mm : 50 mm square edge steel: 50 mm : 13 mm throat: 300 mm Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

flat steel: 350 x 10 mm round bar steel: 35 mm square edge steel: 30 mm L-beam: 80x80x8 mm hole diameter in sheet thickness: Ø 27 in 13 bzw. Ø 20 in 8 mm : 500 kN throat: 177 mm : 34 (Hub 15mm) blade length: 356 mm engine output: 3.0 kW weight: 950 kg dimensions: 1300x1100x1850 mm Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Sheet thickness: 8,00 mm void: 0 Table length: 3100 mm Table width: 0 mm Knife length: 0 mm MACH-id    4417 MAKE        Gasparini Italia TYPE           CO 3006 YEAR            2003 SPECIFICATIONS Guillotine / Lazer / Cutting table      Guillotine Cutting lenght         3100 mm Maximum sheet thickness         8 mm Backgauge stroke X in mm         1000 mm Power resonator kW / Amp       11 kW Controll        DELEM DAC Throat           500 mm DIMENSIONS Length          3300 mm Width           2800 mm Height          1900 mm  

: 32 /min Punching force: 60 to throat: 500 mm : 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: 2012 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /min Punching force: 60 to throat: 250 mm : bis max. Ø 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: ca. 1600 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Punching force: 45 t hole diameter in sheet thickness: Ø 27x13 mm : 24 /min L-beam 90°: 80x80x8 mm L-beam 45°: 60x60x6 mm flat steel: 200x13 mm : 7 mm engine output: 2,2 kW weight: 760 kg Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 27 mm diameter - Rectangular notching device compl. with hold down - notch - Support table for punching device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Sheet thickness: 8,00 mm void: 0 Table length: 3000 mm Table width: 0 mm Knife length: 3000 mm MACH-id   4116 MAKE       Gasparini Italia TYPE         CO YEAR       2003 SPECIFICATIONS Controll    Digital read out Guillotine / Lazer / Cutting table     Hydraulic Cutting lenght       3100 mm Maximum sheet thickness       8 mm Throat           500 mm Backgauge stroke     X in mm      0 - 1000 mm Power resonator kW / Amp      11 kW DIMENSIONS Length       3100 mm Width         2100 mm Height       1900 mm

: 10 mm Punching force: 55 to : 40x10 mm flat steel: 300x15 oder 200x20 mm L-beam 90°: 120x120x10 mm L-beam 45°: 70x70x7 mm : 40 mm square edge steel: 40 mm : 37 /min. throat: 250 mm weight of the machine ca.: 1.600 kg Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 45 to. no. of strokes: 24 Hub/min hole diameter in sheet thickness: max. Ø 27 in 13 mm : 80x80x8 : 60x60x6 mm flat steel: 300x10/200x13 mm : 7 mm engine output: 2.2 kW range L-W-H: 1550x820x1540 mm weight: 760 kg Standard equipment: - Complete knife set for flat steel shears - complete knife set for angle steel shears - complete standard punching equipment - Stamp quick release device for punches up to Ø 27 mm - Rectangular notching device complete with hold-down device - notch - Support table for punching device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : 1030 mm : 8 mm : 5 mm : 14 1/min : 3 ° : 7 pcs. : 500 mm : 7.5 kW : 100 l : 900 mm : 1550 mm : 1150 mm : 1600 mm : 1800 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Sheet thickness: 6,00 mm void: 0 Table length: 3050 mm Table width: 0 mm Knife length: 0 mm MACH-id   4007 MAKE        Amada Promecam TYPE         GPX 630 YEAR        1992 SPECIFICATIONS Controll      Conventionel Guillotine / Lazer / Cutting table       Guillotine Cutting lenght      3050 mm Maximum sheet thickness     6 mm Backgauge stroke X in mm     1000 mm Power resonator kW / Amp    5.5 kW DIMENSIONS Length     3600 mm Width      2200 mm Height     2100 mm

Crushers

digital readout for backgauge retractable backgauge Optional: upgrade to CNC control Cuttinglength: 3100 mm Max sheetthickness st 45: 20 mm Max sheetthickness inox: 15 mm Passage between uprights: 3400 mm Depht of throat: 300 mm Strokes/min: 7 > 30 str/min Backgauge: 1000 mm Adjustable cuttingedge: 0,5 > 3° Electric motor (power): 30 kW Length: 3400 mm Depht: 3900 mm Height: 2800 mm Weight: 22,3 ton

pressure: 60 t square edge steel: 35,0 mm round bar steel: 40,0 mm L-beam: 120 mm punching cross-cut in cmm: 28 in 15 mm throat: 220 mm flat steel: 300 x 15 mm oil volume: 45 ltr. total power requirement: 4,0 kW weight of the machine ca.: 1.250 kg. Dimensions (HxWxD): 1510 x 590 x 1570 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mm plate thickness: 6,0 mm ST 42 thickness at Niro-steel: 4,0 mm VA cutting angle: 1,2 Grad no. of strokes: 28 Hub/min oil volume: 150 ltr. down holder: 11 Stück control: CYBELEC CybTouch engine output: 11,0 kW back stop - adjustable: 1.000 mm table height: 800 mm weight: 4.500 kg range L-W-H: 3.010 x 2.100 x 1.640 mm ------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment ------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws ...

sheet width: 2600 mm plate thickness: 8,0 mm thickness at Niro-steel: 5,0 mm down holder: 12 Stück no. of strokes: 18 Hub/min oil volume: 200 ltr. cutting angle: 1,5 ° engine output: 15,0 kW weight of the machine ca.: 6.300 kg range L-W-H: 3525 x 2350 x 1700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 4100 mm plate thickness: 10,0 mm thickness at Niro-steel: 6,0 mm down holder: 28 Stück no. of strokes: 18 Hub/min oil volume: 260 ltr. cutting angle: 0,5 - 2 ° control: CYBELEC Cybtouch engine output: 22,0 kW back stop - adjustable: 1000 mm range L-W-H: 6100 x 2580 x 2460 mm weight: 15.100 kg. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : 1530 mm : 20 mm : 15 mm : 8 1/min : 3 ° : 7 pcs. : 500 mm : 30 kW : 250 l : 950 mm : 2100 mm : 1400 mm : 2000 mm : 6000 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : 1530 mm : 12 mm : 9 mm : 8 1/min : 3 ° : 8 pcs. : 500 mm : 15 kW : 180 l : 950 mm : 2200 mm : 1200 mm : 1800 mm : 3400 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : 1280 mm : 12 mm : 9 mm : 9 1/min : 3 ° : 7 pcs. : 500 mm : 15 kW : 180 l : 950 mm : 1950 mm : 1200 mm : 1800 mm : 3200 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : 1030 mm : 10 mm : 6 mm : 10 1/min : 3 ° : 7 pcs. : 5000 mm : 11 kW : 100 l : 900 mm : 1550 mm : 1150 mm : 1600 mm : 1900 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : 1030 mm : 6 mm : 4 mm : 14 1/min : 3 ° : 7 pcs. : 500 mm : 5.5 kW : 100 l : 900 mm : 1550 mm : 1150 mm : 1600 mm : 1700 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round bar steel: 45 mm square edge steel: 42 mm L-beam: 140 x 13 mm flat steel: 350 x 20 mm pressure: 550 kN throat: 305 mm notching: rectangle tool: mm total power requirement: 5,5 kW weight of the machine ca.: 1260 kg dimensions of the machine ca.: 1360 x 750 x 1565 mm 2 working cylinder with 2 separated electric foot switch for 2-people-handling New notching table, new knife for the rectangle notcher and new punching table included For further information please see brochure. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2500 mm plate thickness: 12,5 mm distance between columns: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Width of metal, max. 2,500 mm Metal thickness, max. 12.5 mm Weight, approx. 19,000 kg Drive 40 kW Equipment / Special Features: Adjustment of cutting gap. Hydraulic blank holder. Automatic arrester adjustment for cutting blanks. Program input and piece number input. Transportation device for blanks. Stacking device. This is an ideal machine for cutting lots of small blanks out of large pieces of sheet metal. Machine is equipped with a complex stacking device on the back of the machine. This is a heavy and rigid machine. Condition : Good to very good. Machine can soon be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. The data for th ...

The JMC 150 has a mechanically adjustable hold-down. The scissor head is operated with a foot pedal for individual cuts or continuous cutting. The scissor head is protected with a safety basket. The JMC 150 is a tabletop unit for easy handling. Manufacturer: Mc Intyre Knife length: 150 mm Measuring opening: 105 mm Cutting capacity: 25 tons Round iron ST 37: 25 mm diameter Number of strokes at 1/4 aperture: 20 / min Number of strokes at 1/2 opening: 12 / min Number of strokes at full opening: 9 / min Dimensions ( L x W x H ): 660 x 520 x 620 mm Weight: 150 kg Drive: 1.5 kw / 230 Volt Operation: Foot pedal

Alligator scissors Lindemann Alibo The Lindemann Alibo has a mechanical hold-down. The scissor head is protected with a safety basket. Machine On hand Knife length : 760 mm Weight : 4200 kg Mouth width at the tip : 200 mm Cutting capacity: 0.45 kN/ mm² : Ø 70 mm Number of strokes : 20 – 40 cuts/min Dimensions: 4.20 x 1.50 x 1.80 meters Drive: 15 kw Hold-down: Mechanical

CNC-controlled hydr. Sheet metal shearing machine make WEINBRENNER type TSV 6/3050Machine -No: 687 T built in 1987gr. Working width: 3050 mmFor sheets with 45 kg strength up to: 6.0 mmclear column width: 3160 mmclear stator projection: 200 mmCutting angle min./max .: 1/2 °Backgauge adjustment: 1000 mmNumber of hydr. Hold down: 12Number of strokes min./max. (depending on cutting length and material thickness): 22/36 / minHydraulic drive: 380 V, 15 kWTable height above hall: 900 mmDimensions incl. Backgauge, without frontSupport arms: 4100 x 2300 x 2100 mmWeight approx .: 8500 kgWith- Control in swivel control panel CYBELEC CNC 1000- compl. elec. Device with control device in the large switchingxa0Cabinet attached to the side of the machine- Backgauge control with programming- Material quality code- Sheet thickness preselection- stroke length adjustment- Contact cutting device- Scrapweed- ...

JMC 900 alligator shears (new machine) The JMC 900 has a hydraulic hold-down. The scissor head is operated with a foot pedal for individual cuts or continuous cutting. The scissor head is protected with a safety basket. Out of stock Delivery time: On request Manufacturer: Mc Intyre Knife length: 920 mm Measuring opening: 473 mm Cutting capacity: 233 tons Round iron ST 37: 88 mm diameter Number of strokes at 1/4 aperture: 26 / min Number of strokes at full opening: 9 / min Dimensions ( L x W x H ): 3200 x 1030 x 1800 mm Weight: 4400 kg Drive: 18.5 kw / 400 V + 1.5 kw electric motor cooler Operation: Foot pedal

Hydr. CNC-Sheet metal Shear make GWF MENGELE type S 8 - 1500Machine -No: S2544, built in 1989Max. Cutting length: 1550 mmMax. Sheet thickness: 8 mmlateral. Discharge i. Stand: 50 mmSheet metal passage: 16 mmCutting angle adjustable: 2 ° 30 - 0,5 °Empty strokes: 25 - 32Number of hold-downs: 8Cutting pressure: 280 barHold-down pressure: 80 barOil filling: 300 lDrive power: 18.5 kWTotal connected load: 20.1 kWExternal dimensions: 2130 x 3260 x 2360 mmWeight: 5.8 tWith- CNC control SIEMENS S 5 for numerical sheet bending- Holding device mot- Sheet metal removal with conveyor belt- Cutting gap and cutting angle m. Control programmable- Spare knife- Schermesser for 750 kg strength- Separate hold-down z. Cutting after crack- Hold-down pressure adjustable and readable from the front- 2 rocker stops- Finger guard with recessed grip- balls in the support table- Angle stop m. Norius- Footswitchus ...

CNC hydraulic guillotine shears FAbr. HACO HSLX 4010brand newTechnical specifications:Max. Cutting length: 4050 mmMax. Sheet thickness for ST 4 10 mmMax. Sheet thickness VA (1.4301): 6 mmTable height: 1030 mmCutting angle: 0.5 - 3 degreesCutting gap adjustment: 0.05 - 1.0 mmNumber of hold-down devices: 23Back stop area: 1000 mmBackgauge speed: 110 mm / secStroke rate: 7-11Working height: 1030 mmrequired oil filling: 220 litersLength of the angle stop: 1000 mmHolding device option: 7780, -Length of the support surface: 930 mmMax. Sheet thickness: 8 mmMotor power: 18.7 kWOption control panel on the swivel arm: 930.00Machine dimensions: 5150 x 2050 x 2395 mmWeight: 13 tWith- SC 100T controlwith ergonomic control panel - simple operation directly on the cutting table- enables convenient operation ofBackgauge, retraction and cutting length limitation- Electronic cutting gap adjustment - Cutti ...

CNC sheet metal shears make EHT type TSS 4-20Fabr. -No: 107785, year of construction 1998Technical specifications:Working length: 2020 mmmax sheet thickness at 450 N / mm 4 mmOil volume: 160 lelectr. Connection: 400 V, 50 HzDrive line: 7.5 kWDimensions approx: 2800 x 2150 x 2150 mm, weight approx: 4.5 tWith- CNC control ELGO P 8721- Hold-up device- Scrap chute- foot switch- automatic cutting angle- automatic cutting gap adjustment- 3 angle stops in front- Cutting line lightingin a little used and functional conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Specifications: - working width 2540 mm - max. cutting capacity St 40 4 mm - mot. Cutting angle adjustment - Cut gap. by scaled adjustment screws - Number of hydraulic holders 14 pcs - Mot. backgauge with positioning. 10 - 1000 mm - Stroke rate depending on cutting angle and cutting length 23 per min - Hydraulic drive 400 V / 7.5 kW - Table height 1030 mm - Space requirement approx. W 2500 x H 1630 x D 2150 mm - Weight approx. 3600 kg - with: - Sheet metal holding pneum. supported - front angle stop + support arms - Electronic cutting depth adjustment - Cut line lighting - E-foot switch

Hydraulic CNC swing cut guillotine shears make KNUTH type KHT D 3006Year of construction 2018Technical specifications:Max. cutting length: 3100 mmMax. sheet thickness: 0.5 - 6.0 mmCutting angle: 1.3°Number of hold-down devices:16Stroke :105mmNumber of strokes per minute:15Working table height: 865 mmNumber of support arms:3Oil tank: 200LMotor power: 15 kWDimensions approx.: 4110 x 2200 x 2100 mmWeight approx.: 7300 kgwith- Sheet metal holding device- D-Touch 7 control with touch screen for motorized backgauge 1000 mm and intersection- foot switchlittle used, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Hydr. Sheet Metal Shear Make MENGELE Type S 4 - 5000/3Machine -No: S 2237 5000/3 Year 1976Cutting length: 5050 mmMax. Sheet thickness: 3.0 mmlateral. Discharge: 300 mmCutting angle: 0.6 °Strokes per minute: 34Number of hold-downs: 22mot. backgauge: 0 - 1000 mmlateral. Angle stop: 2000 mmOperating pressure: 230 barHold-down pressure: 58 barOil filling: 200 lDrive power: 11 kWOutside dimensions approx: 5750 x 2500 x 1700 mmWeight approx: 15 tWith- mot. backgauge- Angle stop front- Footswitchused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Hand lever plate shears and profile steel shears Knife length 400mm Cuts sheets up to 5mm Cuts round steel up to 13mm Heavy and stable design with foldable storage table. Mounted on base More hand lever plate shears in stock, also for round steel and profiles!

Hydr. Sheat metal Shear make EHT type EHS 6-50Machine -No: 19782 Year 1983Max. Sheet thickness: 6.0 mmCutting length: 5050 mmKnife length: 5100 mmCutting angle: 1 - 15 °Knife strokes per minute: 18Number of hold-downs: 26Pressure p. Hold down: 60 barOperating pressure: 280 barOil filling: 220 lDrive power: 12 kWWeight approx: 11 tOutside dimensions approx: 5500 x 2900 x 2100 mmWith- mot. back gauge 1500 mm with length indicator- Cutting angle indicator- Cutting angle adjustment- Cutting length limit- Footswitchused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Hydraulic sheet metal shears make LOTZE type TS 3000/5machine -No: 2623003 year 1975Technical specifications:Max. Effective length: 3040 mmMax. Sheet thickness steel: 5.0 mmMax. Sheet thickness stainless steel: 3.0 mmOutside dimensions approx: 3750 x 1255 x 1600 mmWith- motor backgauge with handwheel fine adjustment- Cutting length limit- Angle stop front- Table extension- Footswitchused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

sheet width: 3050 mm plate thickness: 6 mm distance between columns: mm blade length: 3050 mm total power requirement: 11 kW weight of the machine ca.: 7,6 t dimensions of the machine ca.: 2,1 x 3,3 x 1,8 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic swing cut guillotine shears make HERA type HSS 3Machine -No: 557 built in 1984heavy, unbreakable all-steel designTechnical specifications:Passage: 1100 mmLarge sheet thickness at 400 N / mm 2.0 mmThroat: 200 mmNumber of strokes: 56 H / minStop length at the front: 1000 mmStop length at the back: 1000 mmMotor power: 2.2 kWWeight about 1500 kgDimensionswith- motorized backgauge- foot switch- front support arms- hydr. Hold-downused, in good and functional conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

cutting length: 1030 mm sheet thickness: 2.5 mm steel Motor-adjustable backgauge up to 1,000 mm in 2 speeds with digital display Pneumatic sheet metal holding up Side stop and table extension Knife sharpened Weight approx. 1000 kg

Swing cut sheet metal shears make RAS type 52.31Fabr. -No: 23/7, built in 2000Technical specifications:Cutting range up to: 3100 mmmax.sheet thickness: 2.0 mmNumber of strokes per minute: 37Cutting angle: 0.9 degreesDrive power: 3.0 kWExternal dimensions approx L x W x H: 3580 x 1700 x 1220 mmWeight approx .: 1950 kgwith- CE marking- Angle stop in front- 2 table extensions- foot switch- Single stroke - continuous run- Cut material switch via hand leverwithout back gaugeused, in good and functional conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Machine type: Sheet metal scissors (lid scissors) Manufacturer: MÜLLER & KURTH Condition: very good Offer type: used machine Specifications: Power: 1100 x 1.0 mm Drive type: by hand Remark: Parallel stop, Hold Weight: 300 kg The machine is in a very good and immediately ready for use condition and can be visited and demonstrated with us. We would be pleased if our offer finds your interest. Errors, changes and prior sale excepted.

Fully hydraulic curved roller Shear make PARX type KRS 2Machine -No: 3728 Series 61/72, year of construction 1973Shearing power b. 40 kg / mm2 strength: 6 mmShearing power b. 70 kg / mm2 strength: 4 mmProjection between stand and knife: 1050 mmStand opening height: 300 mmmin Curve radius: 75 mmmin. Rondendiam.:290 / 180 mmMax. Rondendrm. from 4-corner sheet: 2750 mmminute Flaring rim: 450 mmMax. Beading height: 50 mmMax. Beading radius: 35 mmCutting speed stepless: 0 - 12 m / min.Power requirement: 6 hpWeight: 1.85 t (without mandrel centering)Outside dimensions: 3000 x 900 x 2000 mm(without mandrel centering)With- full hydr. drive- graduated Speed control- Const. Starting and working torque- Automatic workpiece feed- Contour cutting (cropping)- Circular section- Spiral cut- Beading- with adjustable Thorn centeringused, from operational resolution, in good conditionPrice on request.Deliv ...

Circular shears make PARX / KUNZ type KSM / 2 / schMachine -No: 3756 built in 1975Technical specifications:Shear capacity 40 kg / mm2 4.0 mmShear capacity 70 kg / mm2 2.5 mmProjection 380 mmGuide curve projection 750 mmgr. round square sheet metal 1000 mm gr.Ronde octagonal sheet metal 1250 mm Flare diameter max. 400 mmFlare height max. 30 mmFlaring radius max. 20 mmCutting speed 15/30 m / minDrive power 2.5 / 3.0 kWWeight approx. 2500 kgDimensions 3600 x 500 x 2200 mmWeight approx. 2500 kgWith- automated with hydr. Adjustment of the circle center point guidancefor different diameters and material tension in the center- complete electr. Facility- Inclined lower knife shaft- swiveling control panel- hydr. Infeed of the upper tool for scissors and guide arch- hydr. Guide arc swivel device- various cutting wheelsused, in good conditionPrice on request.Delivery: ex warehouse or  ...

Available with 350, 450, 500 and 820 tons cutting force. Continuous work Drive: Electric motor Motor New machine Field of application as follows: -Scrap -Windows and doors made of aluminium and plastic -Alu varieties -Types of wood (pallets, cabinets, industrial wood, more) -Mixed scrap -Bulky waste -more approx. 6 months delivery time after order Further information on request For a written offer, please write an email with your company details and address

Motorized crank sheet metal shears make FASTI type 507 15-3.5Machine -No: 84517010 built in 1984Technical specifications:Cutting length: 1540 mmmax.sheet thickness: 3.5 mmAdjustment range of backgauge: 1500 mmStrokes per minute: 56Drive power: 7.5 kWWeight approx: 1610 kgwith- Front-operated motor stop with digital display and 1 dimension preselection- foot switch- single stroke - continuous stroke - jogging- Side stop 750 mm- 2 table extensionsused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Motorized sheet metal shears make RAS type 83.25Machine -No: 27/10Technical specifications:Cutting length: 2540 mmSheet thickness max.: 3.0 mmNumber of strokes per minute: 50Cutting Angle:1.35°Table width: 430 mmTable height: 750 mmlateral projection: 100 mmRear stop adjustment: 550 mmDrive power: 5.5 kWWeight approx.: 2.5 twith- manual backgauge- manual adjustment of the back gauge from the front with reading scale- foot switch- angle stop- support arms- Tilting roller tableused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools