shear 3100 used for sale

Guillotine shear LOTZE type HSS 20 / 7Cutting length 2050 mmCutting thickness 7 mmwith single back gauge; used

Hydraulic guillotine shears STEINER type HTS 30/20 RMasch. No. 315 Year of construction 1982Cutting length 3050 mmCutting thickness 20 mmBack gauge 800 mm controlledMotor power approx. 30 kWNet connection 400 volts, 50 Hz- Back gauge with positioning control ELGO- Back gauge adjustment via ball screws- Safety light barrier SICK front as protection against interference- 3 pieces Material Support arms with ball rollers- Electric foot switch- Replacement knifeSpace requirement of the basic machine L x W x H 4650 x 2610 x 3200

Guillotine Shears, Metal Shears DIGEP Type OL 3Workshop Overhauled Guillotine ShearFabr. No. 1312 Year of construction 1977Cutting length 1250 mm (nominal cutting length)Cutting length max. 1300 mmCutting thickness at 450 N/mm² 3 mmSingle back gauge 500 mmStand projection 200 mmCutting angle 2 stroke rate at full cutting length max. 50 strokes/min. Working height 860 mmMotor power 2.2 kWNew connection 380 Volt, 50 Hz- LED cutting area-Lighting- Simple backgauge with manual adjustment- Mechanical

Hand lever shears VEB Scherenbau Nossen type ScDH10Knife length: 180 mmSheet thickness: max. 10 mmFlat material: 50x15 mm4-edge solid material: 22x22 mmRound steel: 24 mmAngle steel: 60x7mmT-steel: 60x7mmon mobile undercarriageWeight: approx. 150 kg; used

Hydr. Swing cut guillotine shears HERA type HSS IIIFabr. No. 598 Year of manufacture 1986Cutting length 3100 mmCutting thickness 3 mmStand projection 200 mmKnife strokes 25 strokes/min. Mains connection 380 Volt, 50 HzMotor power 3 kW- motorized adjustable back gauge 1070 mm- actual digital display for the back gauge- cutting gap adjustment- cutting length adjustment- front side stop left 1000 mm- 4 pieces sheet metal support arms 1000 mm- el. Foot switchSpace requirement without sheet metal support arms L x W x H 3630 x

Swing-cut guillotine shears KÖLLSCHEN type BSK 2000/2Fabr. No. 69 1307 Year of construction 1969Cutting length 2000 mmCutting thickness 2 mmStand projection 90 mmWorking height 920 mmMains connection 380 volts, 50 HzEngine power 4 kW- Drive via geared motor with brake and crankshaft- mechanical sheet metal hold-down- manual back gauge 500 mm- stop adjustment via 2 handwheels, rear on the backgauge guide with measuring scale- front side stop left 720 mm- electric foot switch- manual

Hydraulic guillotine shears FASTI type 509 - 25/4Masch. No. 5418 Year of construction 1991Cutting length 2535 mmCutting thickness 4 mmBack gauge 5-1000 mm (controlled)Cutting angle adjustableHydraulic pressure max. 290 barMotor power 7.5 kWNeching connection 400 volts, 50 Hz- Back gauge with positioning control ELGO ELECTRIC Type 85- Sheet metal holding device under the back gauge- Manual cutting gap adjustment with dial gauge display on the right and left- Stepless cutting length adjustment- Hydraulic

Reinforcing steel mesh shears such as guillotine shears, sheet metal shears, sheet metal guillotine shears, hydraulic shears -Manufacturer: Maschinenfabrik Bock, hydraulic guillotine shear, reinforcing steel mesh shear type 2550 -Cutting width: 2500 mm -Max. cutting capacity: Ø 12 mm double at 100 mm pitch -Motor: Dietz 7.5 kW -Space requirement: 3020/2000/H1320 mm -Transport dimensions: 3130/1080/1465 mm -Weight: 2000 kg

intake cross section: 1,600 x 1,200 mm motor power: 2 x 45 kW knife width: 55 mm knife number: 56 pieces rotor flight circle: 655 mm Planetary gearbox

Working width: 1040 mm sheet thickness: 12 mm rear gauge: hand up to 500 mm power: 380 V, 11 kW space: 2500 x 2150 x 1900 mm weight: 4100 kg

Working width: 2500 mm sheet thickness: 4 mm throat depth: 70 mm rear gauge: 520 mm power: 380 V, 6.3 kW space: 3200 x 2300 x 1270 mm weight: 4600 kg

McIntyre 200B Shear Available with or without a stand, this machine might look small but it has a big cutting capacity Small but powerful McIntyre's wide experience in hydraulic equipment manufacture has enabled us to build an 8” shear with a staggering cutting force. Although equipped with only a blade, the high shear force and wide tip to tip opening on the McIntyre 200B means that it can deal efficiently with a whole range of non- ferrous cleaning and sizing operations - in particular larger diameter electric cables and valves. In most cases - if your metal will fit into the jaw of the 200B, then this machine will cut it. Our company can provide this equipment with short delivery time.

Working width: 4100 mm sheet thickness: 16 mm projection: 300 mm rear gauge: 1500 mm power: 400 V, 45 kW space: 4800 x 3500 x 2600 mm weight: 28000 kg

Working width: 5050 mm thickness: 10 mm power: 30 kW space: 2450 x 5600 x 2500 mm weight: 28000 kg

McIntyre 407 CAT Shear Designed to recover the precious metals found in Catalytic converters, JMC Cat shears also versatile enough to be used anywhere in your yard. Purpose Built McIntyre Cat shears have been purpose built for recovering precious metals from catalytic converters. The Catalytic converter is simply placed in the jaws and cut. The movement of the jaw is directly controlled by the moveable foot pedal and a V clamp holds the Cat in place during cutting. Once cut, the pinched end of the converter can be re-opened using the side bracket attached to the top jaw, allowing the contents to be poured out.

Working width: 4100 mm sheet thickness: 6 mm radius: 100 mm rear gauge: 0-1000 mm power: 18.5 kW space: 4600 x 2200 x 1950 mm weight: 11000 kg

JMC 407 overhauled new model / young device Drive: 7,5 KW Weight: 880 kg 4 x reversible knives Truck intake/wheels

1 VOLLENWEIDER cleaning and shearing machine type SUPER DUPLO, width 210 cm

McIntyre 407 Shear An affordable efficient 407mm (16") blade shear with enough power and speed to handle a wide variety of cutting tasks Robust, affordable, efficient Built originally for scrapyard use, the McIntyre 407 shear is robust enough to withstand the most difficult of working environments. It is now our most popular alligator shear with more than 2000 still in daily use worldwide. The McIntyre 407 is able to handle; automotive scrap, whole gear boxes, cylinder heads and blocks, oversized gate valves and of course all the usual non ferrous metal separations. The 407 can also be used to cut ferrous metals. Why

Working width: 3050 mm sheet thickness: 6 mm throat depth: 200 mm rear gauge: 1000 mm power: 15 kW space: 4100 x 2300 x 2100 mm weight: 8500 kg well-preserved CNC hydraulic shear, with pivoting Panel, serial control. CYBELEC, CNC 1000, Hours of operation according to the operating hour counter: 2700 h

McIntyre 500 CAT Shear The 500 CAT is designed for those needing just a bit more blade length without an equivalent increase in price. Versatile The 500 CAT gives customers just a bit more blade length without a big price increase. It is powerful enough to handle most non ferrous cleaning and sizing operations, and can also be fitted with an optional bracket enabling it to assist when processing catalytic converters. Long-lasting In common with all JMC shears, the 500 CAT has been designed and built to last. Blades are deep hardened for extended life, hardened chrome rod is used in the hydraulic ram, and components are all choiceed according to their quality over and above their price.

the machine with two motors each 5.5 kw and blades 40 mm 2 hooks machine complete with hopper and stood and as well as a new control panel

McIntyre 500HD Shear This new generation shear is faster and more powerful than any other machine of its size. Featuring an automatic hold down clamp and 20 inch blade, this model is available as electric or diesel Fast and strong This 508mm, 20 inch, blade shear has been built for speed and power, and will outperform every other machine in its field. The McIntyre 500HD has enough shear force to deal with a wide range of operations and materials including: the cleaning of automotive aluminium scrap, whole gearboxes, cylinder heads and blocks, oversized gate valves, and the handling of all non-ferrous separations. It can also be used for cropping ferrous metals.

14 Fields pallets shelving (used) -Various manufacturers such as Fa.Polypal-Dexion Metalux Jungheinrich -15 Stand / 56 bars -Traverse length 2.70 m - load per level 2.4 tons -Shelf height: 6.00 m depth 1, 05 m -removed / reverse loading done Artkelstandort: Bavaria (room Rosenheim) / Germany / Hessen, Germany (room Fulda) / Germany / Tirol / Austria Intermediate sale is reserved ______________________________________________________ Freight / delivery Current obligation estimated about freight costs for the German Federal territory amounted to approximately 450 euros. For our customers we offer a low-cost, reliable carrier who delivers the goods at a most affordable price. For the 1:1-we vouch for us passing the dispatch or shipping costs. Self pick-up possible - by appointment. Delivery time approx. 2 weeks Shipping throughout Europe after consultation and confirmation email. Comme ...

Sheet metal width - 170 mm, Sheet thickness 8 mm. 80 x 10 mm, flat steel Steel bar cutting stencils for round and square Knife length 170 mm. Sheet holding device Machine length 800 mm (1000 mm with moveable base) Machine height 500 mm plus 560 mm for base Machine weight 255 kg,. on mobile base

Hand lever plate and profile steel shears heavy and stable outing cuts sheets, round steel (approx. 15mm), flat steel and T-profiles Mounted on base Special price

Knee lever shears for sheet metal Cutting length 15 cm maximum sheet thickness 3 mm Built in 1982 L x W x H: 50 x 40 x 150 cm Weight approx. 50 kg The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/Ersatzteile durch MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Maschinenbau Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

McIntyre 500HD Shear This new generation shear is faster and more powerful than any other machine of its size. Featuring an automatic hold down clamp and 20 inch blade, this model is available as electric or diesel Fast and strong This 508mm, 20 inch, blade shear has been built for speed and power, and will outperform every other machine in its field. The McIntyre 500HD has enough shear force to deal with a wide range of operations and materials including: the cleaning of automotive aluminium scrap, whole gearboxes, cylinder heads and blocks, oversized gate valves, and the handling of all non-ferrous separations. It can also be used for cropping ferrous metals.

Reinforced steel scissors Round iron scissors Scissors Manufacturers Muhr and Bender Type 50N/22 and 50N/28 50N/22 intersects at 450N/mm2: Round: 22mm Square 22mm Flat: 35x10mm 50N/28 intersects at 450N/mm2: Round: 28mm Square 24mm Flat: 40x15mm Both machines new and ovp Special price

McIntyre 600 CAT Shear Cat shears are powerful enough to deal with a wide range of operations including the cleaning of automotive aluminium scrap, whole gear boxes, cylinder heads and blocks, oversized gate valves and the handling of all non ferrous separations. VERSATILE The 600 CAT features a blade guard system which gives good visibility to the operator and acts as a hold down to prevent material kick back. The machine is foot pedal operated and the jaws return to the open position once the foot pedal is released to increase safety. Wheels are fitted as standard, and forklift points have been included on the body of the machine to ensure that it can be safely lifted both within the yard and during transportation.

Manufacturer: Mc INTYRE Blade length: 150 mm Blade opening: 105 mm Cutting capacity: 25 tons Rods ST 37: 25 mm diameter Number of strokes at ¼ opening: 20 / min Number of strokes at ½ opening: 12 / min Number of strokes at full aperture: 9 / min Dimensions (L x W x H): 660 x 520 x 620 mm Weight: 150 kg Drive: 1.5 kw / 230 Volt Control: foot pedal

Working width: 3050 mm sheet thickness: 6 mm throat depth: back gauge: 650 mm power: 380 V, 16 kW space: 3680 x 2060 x 1870 mm weight: 7580 kg

McIntyre 600 GT Shear Another Shear in the McIntyre GT Range, the 600 gives a massive cutting area for its relatively diminutive size. Versatile The 600 GT features a blade guard system which gives good visibility to the operator and acts as a hold down to prevent material kick back. The machine is foot pedal operated and the jaws return to the open position once the foot pedal is released to increase safety. Wheels are fitted as standard, and forklift points have been included on the body of the machine to ensure that it can be safely lifted both within the yard and during transportation. Ideal for larger items such as car radiators which can be handled in just one pass, the 600 GT can also be adapted to process catalytic converters.

Professional steel shears for tin locksmiths, assembly plants, Teaching work pieces, particularly stable construction stable application with shear encoder made of encoded steel tooth lever translation lever securing via rotary spring knives made of high-quality tool steel, hoisted and ground continuously adjustable holder cuts of sheets, flat steel steel mm: 18 knife length mm: 175 Net weight kg: 47.5 room requirements approx.0.5x0.25x2 m; ready for use

McIntyre 900 Diesel Shear A reliable workhorse equipped with 920mm (36.25") blades to allow you to handle larger pieces of material with ease All round yard shear Designed to give maximum possible blade length without losing cutting capacity, the 900 shear is perfect for a wide variety of yard uses in particular the handling of larger pieces of non ferrous scrap. The 900 can be operated via a foot pedal for more accurate control, or can be set to work continuously to enhance processing speed. The machine is built to last using top quality components and is equipped with a heavy duty guard to improve operator safety.

Manufacturer: Diebels GbR recycling machines Cutting capacity: 30 ton Materials:-Aluminium (cylinder heads), brass (taps), copper, etc. Special features: work desk side folding Weight: 1100 kg Drive: 7,5 kw / 400 V Control: foot pedal

Manufacturer: Weinbrenner Type: TSV 6 / 3050 Year of constr.: End of 2015 demonstration machine Cutting length: 3050 mm Cutting capacity: 6 mm (steel) Hours of operation: 54 Control: Cybelec DNC 60 Dimensions L/W/H: 4100/2050/2100 mm Table height: 1000 mm Weight: 8500 kg Min. cutting angle: 1° Cutting angle max.: 2.5 ° Stroke rate minimum: 20 min. Max speed: 25 min. Cutting gap adjustment: motorized Cutting angle adjustment: hydraulic Number of holders: 14 Rear velocity range: 1000 mm Security: setting the photocell safety on the front and back Oil filling: 225 l Electrical power: 15 KW Power consumption: 3 x 400 V / 50 Hz Back-up fuse: 50 A Additional equipment: Extension of the side stop on 2050 mm Side stop side swing-away A total of 8 support arms freely movable along the entire length of the table The machine is a demonstration machine in mint cond ...

Max punching force: 1100 kN Extension: 510 mm Large support table with material flaps on the punchside Electric contact load stop for heare hydraulic holder for profile and flat steel shears with a wide range of tools ; Very good

Cutting Lenght 6000 mm Cutting Thickness 16 mm Stroke per Min 10

McIntyre 900 Shear A reliable workhorse equipped with 920mm (36.25") blades to allow you to handle larger pieces of material with ease All round yard shear Designed to give maximum possible blade length without losing cutting capacity, the 900 shear is perfect for a wide variety of yard uses, in particular the handling of larger pieces of non-ferrous scrap. The 900 can be fitted with solenoid control allowing it to be coupled to infeed or outfeed conveyors. Other optional equipment for the 900 shears includes oil-immersed tank heaters, forced air cooling and infeed table to handle oversized material

Maximum punching force: 1100 kN Maximum shear force: 1700 kN punch ing: 510 mm support table hole 31 in 25 mm flat steel: 500 x 22 mm hydraulic holder for the flat steel knife kago n weight: approx. 5000 kg ; Very good

cutting effort 1000t the number of strokes (no load) 17 /min course a support of the blades 140mm Max. cutting diameter of rounded workpiece, mm 190 Max. cutting diameter of squared workpiece, mm 180 for 450 N/mm2. Machine weight, kg 60000

Mechanical sheet metal shears of excellent quality, for the burr-free precision cutting of sheet metal up to 1.2 mm sheet thickness steel sheet/ST40 – aluminium 1.5 mm, backdrop-guided knife beam Largest cutting length 4,080 mm, cutting angle 1.5° - up to 25 cutting strokes/min, NC - controlled rear stop with 750 mm travel range, slantable for conical cuttings - automatic removal of the stop rail at sections deeper than 750 mm - with forced-controlled sheet lifting device - automatic tipping device for the sheet metal cuttings into the section collection cart, Scissor table height 800 mm - scissor table width 300 mm - Scissor table extension up to 480 mm support width, dimensions 4.75 m x 1.68 m x H 1.46 m, drive power 2.2 kW, weight approx. 1,500 kg