We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
123,456 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
new
table diameter: 1300 mm table load: 3 t swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min : 6000 Nm 0: 1,1 / 1,1 kW welding current: 700 Ampere • Self-locking gear, therefore no forward and backward at eccentric load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
table diameter: 1100 mm table load: 2000 Kg swivelling range: 0 - 135 Grad turning speeds: 0,1 - 1,0 U/min height adjustment: 1100 - 1550 mm max. torque on the faceplate: 4000 Nm engine output: 1,1 / 0,75 kW welding current: 500 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. Welding power transmission for max.500Ampere. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
table diameter: 1400 mm table load: 4 t swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min : 8000 Nm 0: 1,1 / 1,5 kW welding current: 700 Ampere • Self-locking gear, therefore no forward and backward at eccentric load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
The PV-350 LSHIX machine is a wrapper equipped with a film coil at the bottom of the machine, so it is especially recommended for wrapping irregular or difficult to drag products. This family adds to the robustness, ease of use and reliability characteristic of ULMA machines, great versatility and flexibility in format changes, as well as a wide range of versions, ensuring a perfect adaptation of the machine to the baling needs of each application. The great flexibility and proven reliability of these wrappers make them a family with a wide implementation in the food market in general, and especially valued in sectors such as agriculture, meat, dairy, etc ... Machine built in stainless steel and materials protected with anticorrosive treatment. Right-to-left work direction. Cross welding with clamp with horizontal grooves. Longitudinal welding system using 3 pairs of rollers ...
used
LIQUIDATION of flow pack machine of the Spanish manufacturer RAELMA. This machine performs the function of wrapping in horizontal system (flow-pack). The dragging or introduction of the product is done through bars synchronized with the weld, giving a perfect finish with equal margins in both short and long objects, making the minimum changes. Model HORIZONTAL ENVELOPER GALAXY V. Strong steel structure with reinforced zones for areas of greater effort. Easy movement of the machine through wheels and a good grip with suction cups, making the machine is regulated to about 90mm. Signaling of faults or openings of protections through the touch screen. Pre-selector stop counter via touch screen. Packet/minute production counter via touch screen. Control panel at twenty-four volts according to current regulations. It carries coils at the bottom with positioning of manual self-centerin ...
used
Coating machine ensuring perfect and uniform coating of products. A conveyor belt transports the product, which is submerged by a 4-cascade curtain to ensure full coverage of the product. The bottom of the product is covered during passage through an immersion device. The speed of the conveyor belt can be adjusted by the frequency inverter. The correct amount of batter can be adjusted with a valve on the feed. A specially designed hygienic fan blows the excess beater over the top of the product while the excess dough at the bottom is removed by an additional scraper or bottom vent. The blowing speed is controlled by frequency inverter and can be adjusted according to the application. - Production of high-quality products and extended production runs - 4-layer curtain for full coverage - Adjustable treadmill speed via variable speed drive - The amount of batter can be adjusted wi ...
new
table diameter: 2000 mm table load: 10000 Kg swivelling range: 0 - 130 Grad turning speeds: 0,02 - 0,2 U/min height adjustment: 1450 - 2200 mm max. torque on the faceplate: 20000 Nm engine output: 1,5 / 2,0 kW welding current: 1000 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
table diameter: 2000 mm table load: 10,0 t swivelling range: 0 - 135 Grad turning speeds: 0,05 - 0,5 U/min max. torque on the faceplate: 20000 Nm table pass: 200 mm welding current: 1000 Ampere total power requirement: 3,0 + 4,0 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
clamping range of chuck: 10 - 200 mm height: 67,5 mm daylight: 65 mm external diameter: Futter 200 mm external diameter: Spannhebel 360 mm weight: 4 kg Characteristics: • Self-centering. • Reversible jaws. • Fixed clamping levers allow fast workpiece changes. • Low weight and flat design minimize the center of gravity. The D-D quick chuck enables a quick product change and is suitable excellent with frequent component changes. You do not need a loose one Quick release wrench, as the levers are integrated into the quick release chuck. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
table diameter: 1300 mm table load: 3000 Kg swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min height adjustment: 1200 - 1800 mm max. torque on the faceplate: 6000 Nm engine output: 1,1 / 1,1 kW welding current: 700 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. Welding power transmission for max.500Ampere. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Slicer, automatic vertical sausage slicer, from the Austrian manufacturer of the highest quality S.A.M., model 371.8 I fb. Made of stainless steel and anodized aluminum. Ideal machine for slicing and automatic placement, placing the product in different formats: stacked (block), horizontal fan stacking, vertical fan stacking and round or plate type format. It has different programs to configure, space between slices, units etc. Equipment totally rebuilt, revised and guaranteed. The S.A.M. is operated through the LCD screen by icons that are self-explanatory. It is also possible to save or reuse defined cutting parameters using a 3-digit PLU. Includes blade sharpener. FEATURES: Cart accommodating the product is 500mm long x 270mm wide. Product size: round min. 50mm max. 210mm, square max. 320x210mm. 370 mm diameter stainless steel cutting blade, cutting speed ...
used
Slicer, automatic vertical sausage slicer, from the German manufacturer BIZERBA, model A404. Made of stainless steel and anodized aluminum. Ideal machine for automatic slicing depositing stacked (block), or fan-shaped, has different programs to configure both the thickness of the slice, space between slices, units etc .. Equipment totally rebuilt, revised and guaranteed. The A404 is operated via the LCD screen using self-explanatory icons. It is also possible to save or reuse defined cutting parameters using a 3-digit PLU. FEATURES: Cart accommodating the product is 400mm long x 270mm wide. Product size: round min. 50mm max. 180mm, square min 50x50mm max. 240x175mm. Stainless steel cutting blade of 330 mm diameter, speed 266 rpm. Integrated motor-driven product feed trolley. Precise and consistent cut thickness (05 to 12 mm) Machine dimensions: 640 x 980 x 680mm high ...
new
cutting diameter: 220 mm saw band length: 2450 x 27 x 0,9 mm table height: 915 mm band speed: 35 + 70 m/min connected load frequency: 400 V capacity 90 degrees: round: 220 mm capacity 90 degrees: square: 210 x 210 mm capacity 90 degrees: flat: 230 x 185 mm total power requirement: 1,2 kW weight of the machine ca.: 240 kg dimensions of the machine ca.: 870 x 1550 x 1740 mm The Zimmer Z241/R is a self-lowering saw for miter cuts from 0 ° - 60 ° left. After the cut, the machine stays through one Safety limit switches stand. The reduction is infinitely variable Hydraulic system adjustable. The saw arm can be raised after the cut any position. The saw arm remains at the desired position stand. The Z241 / R has the following features: Hydraulic cylinder, emulsion pump, eccentric tensioner, base, saw band, 400V Connector -16A- The machine is completely assembled and delivered ready for use. ...
new
table diameter: 2500 mm table load: 20,0 t swivelling range: 0 - 135 Grad turning speeds: 0,04 - 0,4 U/min max. torque on the faceplate: 40000 Nm table pass: 200 mm welding current: 1000 Ampere total power requirement: 5,5 + 11,0 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
centre distance: 8500 mm turning diameter over bed: 1070 mm turning diameter over slide rest: 800 mm spindle bore: 128 mm turning speeds: 1,12 - 1120 U/min Control: Alan Bradley 9-series total power requirement: 62 kW weight of the machine ca.: t dimensions of the machine ca.: m 3 Shear Bed, Carriage can bypass Steady Rest and Tailstock 6-position Sauter Turret 360 mm Capacity Self Centering Hydraulic Steady Rest 385 mm Capacity Rotaring Work Support (Used for Gun Barrels) 800 mm 4-Jaw Chuck Tailstock Quill diameter Ø 200 mm Tailstock Taper M.T. 6 Chip Conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Machinery for sandwich packaging. Custom manufacturing machine built in stainless steel, high strength aluminum, with control panel protected with stainless steel box and self-steering wheels with brake. Only thermos seals the tray, it does neither vacuum nor gas injection. Double format of tray sealing for sandwiches in which it can be used separately. The measurements of the outdoor machine are: working height 94cm, max. height 178cm, length 200cm and width 50cm. Sealing last measurements: length 18cm x 7.5cm wide and 18cm x 8.5cm. Specially designed for sandwich packaging by controlling belt speed and direction. Sandwich traysealer, tray traysealer, automatic traysealer, packaging machinery. Its condition is excellent re-release. Equipment revised and guaranteed practically new.
used
1 complete ready-to-use WEHO hot air heater operated with heating oil, immediately available from the site for self-dismantling
used
:::TECHNICAL SPECIFICATIONS::: CNC Model: Fanuc CNC Version: 0i-TC Main spindle nose: ASA 6 Main spindle self-centering diameter: 250mm Main spindle bar passage: 65mm Turning diameter: 280mm Turning length: 550mm Number of turns main spindle: 4000 Number of Tool Towers: 1 Number of tool places first turret: 12 Number of motorized first turret: 12 First turret tool attachment type: VDI 30 X axis travel first turret: 245mm Z axis stroke first turret: 600mm Rapid advances linear axes X Y Z: 36m/min Tailstock: yes Barrel stroke: 190mm Chip evacuator: carpet Number of motorized tool holders supplied: 2 Number of fixed tool holders supplied: 10 :::D IMENSIONS AND WEIGHT::: Length: 3415mm Width: 1786mm Height: 1780mm Weight: 3900Kg
used
Wohlenberg Sprinter 7011 Gathering Machine 24 stations Equipment: -> Preparation for inline operation with perfect binder (e.g. Golf 6001, Champion 8000, Master 6501/7000, etc.) Drive for single and inline machines -> manual feeding station incl. control for automatic switching on and off -> additional blowing air in the transport duct -> Criss Cross Display -> ACC Automatic Caliper Control automatic sheet thickness control, self-learning, for > Faulty sheet inspection > Double-sheet inspection > plus/minus control -> electric disconnect clutch 12/13 station Factory specification format size: max. 460 x 320 mm min. 105 x 75 mm maximum product thickness 80 mm Built in 1998 and extended in 2006 incl. blowers and vacuum pumps NEW: Video part1/2 on youtube Price plus VAT EXW. All information is subject to change. Subject to prior sale. Dealer ...
new
DYNAJET 350th HELI The mobile and universally applicable dynaJET cold and hot water high-pressure cleaner 350th with up to 350 bar working pressure stands out in addition to its ease of use in particular due to its low weight, its compact dimensions and its high performance and safety level. Construction - 1-axle chassis for easy manoeuvring - Self-supporting and indestructible framework for weight optimization - Crane eyelet for easy transport and handling - Operating hours counter for optimal post-calculation - Underrun protection for additional safety - Frame in dip painting technology for high corrosion protection and highest surface quality - Targa concept with separation between the unit side and the operating side for enormous advantages in ergonomics, the Overall machine safety and noise reduction - Impact-resistant lockable hoods made of glass fiber reinforc ...
used
workpiece weight: 100 - 3.000 kg workpiece length: 5.000 mm diameter: 1.260 - 1.600 mm Control: CAP920 total power requirement: 11 kW weight of the machine ca.: 20 t dimensions of the machine ca.: 20 Container m Mobile balancing system SCHENCK for use anywhere in the world The balancing system is permanently installed in a 20 open-top container. The container is equipped with everything you need for balancing • Lighting • Metal base plate 12,000 kg as a base plate for accuracy • Compressor for working air supply distributed in the container • Compressed air connections. • A circumferential power strip • A tool cabinet equipped with tools • A hydraulic lifting device for aligning the container from the outside • In addition to a tarpaulin for the roof, the container also comes with movable roof segments made of sheet metal. • The container has a central plug through whic ...
used
Self-propelled telescopic boom lift 360° The JLG Toucan 1010 boom lift is equipped with a robust and easy-to-maintain electric motor. It allows 2 people to work at a height of 10.10 m or with a lateral reach of up to 3.12 m. High-quality components from well-known manufacturers guarantee a long service life and short-term spare parts procurement even after years. Its non-marking tyres make it ideal for indoor use on sensitive ground. This makes it ideal for maintenance and assembly work at heights. All functions can be controlled from the basket. The movement is possible in all positions, even at full height. The superstructure can be rotated so that lateral working areas can also be reached. Specifications: Brand: JLG Type: Toucan 1010 max. working height: 10.10 m max. platform height: 8.10 m Platform size (LxWxH): 0.9 x 0.7 x 1.1 m Stage load capacity: 200 kg ...
used
:::TECHNICAL SPECIFICATIONS::: CNC Model: Siemens CNC Version: 840D Main spindle nose: ASA 8 Inverted lathe: yes X axis spindle travel: 850mm Z axis spindle travel: 250mm Stoker or spare parts warehouse: yes Main spindle power: 43Kw Main spindle self-centering diameter: 315mm Turning diameter: 250mm Turning length: 125mm Number of turns main spindle: 4300 Number of Tool Towers: 1 Number of tool places first turret: 12 Number of motorized first turret: 12 First turret tool attachment type: VDI 50 Rapid linear axis feeds X Y Z: 45m/min Chip evacuator: carpet Number of motorized tool holders supplied: 1 Number of fixed tool holders supplied: 10 :::D IMENSIONS AND WEIGHT::: Length: 3380mm Width: 1300mm Height: 2900mm Weight: 7000Kg
used
Labeller Manufacturer BBK Type ESB 1207-1832 Year of construction 2012 suitable for self-adhesive labels
new
Blasthouse components as a kit for self-assembly or by assembly by our specialist personnel. Flat conveying floor, transverse screw conveyor, bucket elevator, wind screening, sieve, abrasive bunker, blasting device, filter system, blow-in system, suction wall and electrical control.
used
Machine with painted aluminum structure, equipped with Lexan protections complete with micro safety. Easy to clean and accessible. Technical data: Length mm 3750 Width mm 2700 Height mm 2080 Sliding surface height mm 700 – 1000 Weight Kg 1600 Voltage Volt 400 Frequency Hz 50 / 60 Current A 11 Mechanical speed carton / min 200 Production characteristics: Case length mm 75 – 350 Case width mm 140 – 450 Case height mm 120 – 350 Equipped with: one input product feeding belt; pneumatic product elevation group; stainless steel AISI 304S stacked product collection hopper with independent motorization; product introduction group with own motorization complete with encoder. The machine is also equipped with inclined carton magazine with a capacity of about 50 cartons; carton picking unit, with suction cup arm with independent motor complete with encoder; carton tr ...
used
The unit is suitable to pack blisters in PVC + Aluminum, Aluminum + Aluminum, Polypropylene, PET and PVC, Aclar, COC. All the stations are remarkably easy to access and all the movements are fully visible, so that the line is very easy to clean. This machine is equipped with various safety devices to protect the operator. Product parameters can be recalled from a PC, for a quick and easy format change. Reel unwinder driven by a Brushless motor, with automatic machine stop at reel end. Film splicing table equipped with integrated cutter, and automatic vacuum. Forming station entirely managed by Brushless motors. Self-aligning pre-heating plates, independently motorized. Film positioning driven by Brushless motor. Automatic Pitch adjustment directly from the display. Loader trolley MS170 with a maximum load of 300 kg. Dedicated product feeder and relevant enclosure easily remov ...
new
DYNAJET 350th HELI high pressure hot water cleaner. Including 1st UVV WITH arrival and maintenance (plus spare parts) on the same date (value approx. 1,500 net). The mobile and universally applicable dynaJET cold and hot water high-pressure cleaner 350th with up to 350 bar working pressure stands out in addition to its ease of use in particular due to its low weight, its compact dimensions and its high performance and safety level. Construction - 1-axle chassis for easy manoeuvring - Self-supporting and indestructible framework for weight optimization - Crane eyelet for easy transport and handling - Operating hours counter for optimal post-calculation - Underrun protection for additional safety - Frame in dip painting technology for high corrosion protection and highest surface quality - Targa concept with separation between the unit side and the operating side for eno ...
new
unused, new Kleenoil filter system for workshop use Type S6-103 Year of construction 2023 Execution: Mobile oil filter system Steel construction, powder-coated 6 ultra-fine filter units SDU-H8 incl. 6 filter elements SDFC with the option of use 1 x 6 or 2 x 3 Filtration capacity (average) 500 l/h (40 cSt) For oil quantities up to 10,000 l Self-priming gear pump Pre-filter unit with washable filter cartridge Automatic low-pressure shutdown Pressure gauge display Component protection IP55 Transfer function - oil pumping without filtration 6 m suction and return hose with quick couplings Starting viscosity: max. 1,000 cSt. Filtration viscosity: < 200 cSt.
new
Manufacturer ARPAC Line date: 2018 new, original packed Product description: Plastic Jar, 35 jars (bottles) / Minute (per line) Packaging description: RSC Cases (regular slotted case) , tape sealed System description: PART ARPACK ARPAC developed an integrated solution for this end line packaging system. Product is received single lane, diameter-to-diameter, into an automatic cartoning machine. Cartons are pushed into the required case pack configuration by a pneumatic row pusher. Product is collated, packed into a case, and manually palletized. Labellers: Jars (bottles) arrive filled, sealed, and are already labelled One Jars are placed inside a carton, the flaps are sealed with glue and a printed label with date/lot code is applied. Once cartons are placed in case, the flaps are sealed with tape and a printed label with date/lot code is applied. Features: - (3) Print an ...
used
OMSO DM144/ 6 LIDS, 6-Color Lid Printer, only used for 26,000 hrs ! Infeed Conveyor for feeding Vertical Lid Stacks Robotic removal of Lids from stack to Print Conveyor Auto-Denester Unit No Lid no Ink and No Lid no Print System ARCOTEC CG20-2 Pretreatment station Main 6-Color Print Unit Speed Control for Ink Fountain Rollers Printing Roller self-cleaning device Max. speed 30,000 Lids/ hr (depending on Lid size & shape) Max. Lid dia. Ø 200 mm Min. Lid dia. Ø 50 mm Max. Lid Height 25 mm Max. Rectangular Lid size: 200 x 200 mm Max. Printing dimensions: 180 x 180 mm No. of Printing Blankets 4 UV Tunnel TUV 0077-99 UV-Tunnel power rating : 8 kW Main printer power rating: 20kW Polytype Counter/ Stacker unit delivers Counted Lid Stacks. 400 V 3phase, 50 Hz, Printing Plate Pre-registration Unit. with Monitor Display
used
Item condition: maintained Availability: immediately Printheads clean and rinsed: yes The A300 offers consistently high quality – across a variety of formats – even in the harshest environments. The robust and durable housing made of 316 stainless steel offers excellent protection against dust and water. Thanks to the unique self-cleaning ink system and our patented SureStart operation with a single press, the total cost of ownership is low with minimal operator intervention. It's the perfect choice when you need a rugged, flexible printer that offers maximum productivity.
used
M. No.: 12091 Equipment / Additional information: DESCRIPTION: The sealers Pactur thanks to their production concepts, can be easily transported. The electronical control grants good performances and user friendly functioning. Although they have a limited foot print, are equipped with a real shrink tunnel, which grants high packaging perfomances and excellent results. The machine has two conveyor belt movement cycles, choiceable from the control panel: forward-forward and forward-reverse. Forward-Forward, with product outflow from the side opposite the load, for greater productivity. Forward-Backward, with product return to the operator, for fragile products or logistical needs. SECTORS OF USE: Pharmaceutical, chemical, cosmetics, food, dietary, medical devices, manufacturing. MAIN FEATURES: Semi-automatic sealer with shrinking tunnel Pactur type Lady Pack 45/SL 2 includ ...
used
I sell large control cabinet made of steel, empty, 300 €, only self-collection. Weight 330 kg, size 2.93 m x 2.00 m x 0.75 m
used
Line date: 2018 new, original packed Product description: Plastic Jar, 35 jars (bottles) / Minute (per line) Packaging description: RSC Cases (regular slotted case) , tape sealed System description: ARPAC ARPAC developed an integrated solution for this end line packaging system. Product is received single lane, diameter-to-diameter, into an automatic cartoning machine. Cartons are pushed into the required case pack configuration by a pneumatic row pusher. Product is collated, packed into a case, and manually palletized. Labellers: Jars (bottles) arrive filled, sealed, and are already labelled One Jars are placed inside a carton, the flaps are sealed with glue and a printed label with date/lot code is applied. Once cartons are placed in case, the flaps are sealed with tape and a printed label with date/lot code is applied. Features: - (3) Print and Apply Bar Co ...
used
Carton erector, Bedo – second-hand - : Price from location: 29.500.- € (net)! Manufacturer: Bedo Type: VA 1195 Year of construction: 2006 two cardboard magazines Machine number: 1195.1.6684 400V/3PN/ 50Hz Control voltage: 24V 14.2 A Compressed air: 5- 7 bar With Nordson ProBlue 4 Adhesive Melter 4 Litre Hot Melt Glue Condition: good Available: from approx. Mid-January 2024 Location: Hanau area Manufacturer's text: Series 11 up to 20 cartons per minute Folding crates according to FEFCO 0201, 0200, 0209 and others all types of corrugated board Carton closure by means of hot melt glue, self-adhesive tape or gummed tape small to very large carton formats one or two cardboard magazines motoric/pneumatic mode of operation no format parts
used
This Gorman Rupp T6A water pump is built with a Lister CD4 motor in a sound-damped housing. The Gorman-Rupp T6A is a self-priming pump unit for pumping clean water or mixed water with solids. Steel fully welded chassis. Equipped with drain plug, environmentally friendly oil leakage base design and forklift beams., Can be supplied with any desired coupling/connection., Max flow : 335 m3, Max head : 23 MWK, Max Dirt Diameter : 76 mm, , = More information =, , Year of manufacture: 2005, Applicable material: Water, Connector size: 6, Quick coupler system: Yes, Technical condition: good, Visual appearance: average, Damages: none, , = Dealer information =, , Aroused your interest? . The sales team will be happy to answer any questions you may have. CALL or EMAIL us, we are here for you! We would like to be your supplier ! Also for spare parts, pipes, hoses , coupling systems and fittings. A ph ...
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Mori Seiki NT 1000 multitasking lathe :::SPECIFICATIONS::: CNC Model: Mori Seiki - CNC Version: Mapp - Spindle Nose: ASA 5 - Spindle Power: 11Kw - Main Spindle Speed: 6000 Turning diameter: 370mm - Self-centering diameter: 210mm - Bar passage: 42mm - Turning length: 424mm - Number of tools: 90 Tool holder: CAPTO C4 Spindle speed: 12000 X-axis travel: 380mm Y-axis travel: +105 -105mm Z-axis travel: 460mm Swivel B-axis travel: +120° -120° degrees Rapid feeds linear axes X Y Z: X 40 Y 40 Z 50m/min High refrigerant pressure: yes Pressure value: 50bar External tank system with filter: yes Number of Tool Turrets: 1 Number of first turret tool slots: 10 Number of fixed tool positions in the first turret: 10 First Turret X-Axis Travel: 155mm First Turret Z-Axis Travel: 610mm Sub-spindle: yes Sub-spindle speed: 5000 Sub-spindle power: ...
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Self-aligning ball bearings -Bore: Ø 45 mm -Outer diameter: 85 mm -Width: 19 mm
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Self-priming side channel pump capable of handling gas along with the medium and operates at a low noise level.
used
Filler BERTOLASO – SUPREMA • Year: 1990 • Speed: 3.000 bph • Direction: Clockwise • 16 valves – isobaric o De-gassing o Self-leveling o Pre-evacuation • Safety protections CODE: T 105