section bending used for sale

Manufacturer: Faccin Model: 4 HEL 2128 Type of Machine: Round Bending Machine Condition: used Find more here - / Contact us at -

Key data: 2040 mm, 1 mm

with rebate groove in the upper shaft, with steel wheel and scale, solid, stable construction, with wire inserts, 70 mm feed of the rear roller, Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 2040 mm Sheet thickness: 1.0 mm Colour: green Machine weight: 600 kg Dimensions: 2200 x 650 mm Diameter:. 70 mm Machine number: 8413105

Specifications: Working length: 3050 mm Max. bending power: 30.0 mm Max. bending capacity length 1500 mm: 42 mm Bend: 25.0 mm Diameter upper roller: 460 mm Diameter lower roller: 460 mm Number of driven rollers: 3 hydraulic snap roller bearing Engine power: 37 kW Dimensions (length x width x height): approx. 5850 x 2550 x 2650 mm Weight: approx. 30 tons Note: Compact design, therefore low space requirement Parts of the hydraulics installed under the machine

Specifications: Working length: 2550 mm Max. bending power: 6.0 mm Bend : 4.0 mm Diameter upper roller: 176 mm Diameter lower roller: 176 mm Control panel with digital display Motor power: 7.5 kW CE mark Dimensions (length x width x height): approx. 4000 x 1400 x 1500 mm Weight: approx. 3.6 tons Note: the machine was used exclusively for straightening coated aluminum sheets Rollers were wrapped in foil, which was removed without leaving any residue Condition of the rollers almost as good as new few operating hours

Specifications: Working width: 1050 mm Max. bending power: 100.0 mm Max. bend: 80.0 mm Diameter upper roller: 530 mm Diameter of side rollers: 530 mm Conical bending device by inclined position of the two side rollers Mobile control panel with digital display Engine power: 37 kW Hydraulic Safety Chucks CE mark Net weight: approx. 16 tons Auxiliary: 2. Roller set : Diameter upper roller: 360 mm Diameter of side rollers: 360 mm

Specifications: hydr. Four Roll Round Bending Machine Working width: 4000 mm Max. bending power: 10.0 mm Max. bend: 8.0 mm Diameter upper roller: 305 mm Diameter of side lower rollers: 305 mm Diameter middle lower roller: 265 mm Conical bending device by inclined position of the two side rollers Hardened rollers Hydraulic Safety Chucks Lateral bending aid on the right side Mobile control panel Dimensions (length x width x height): approx. 7300 x 1600 x 1600 mm Net weight: approx. 17 tons

Key data: 50 t, 270 mm, 850 mm

Electric horizontal bending machine HorizOne 50 with spindle drive from CoastOne in Finland. 500kN pressing force thanks to precise and low-maintenance spindle drive with servo motor and servo controller. Simple, intuitive programming with the proven CoastOne TC12-2D controller. Automatically controlled side stop for convenient machining of your sheet metal parts from single part production to series production.

! KNIFE RETURNS! Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1050 mm, H=1240 mm two-tone powder-coated Housing : gentian blue structure (RAL 5010) Extracts : grey-white structure (RAL 9002) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 410 kg As a set, approx. 26 linear metres of bending tools are fully assembled. Available in different sizes and with many accessories!

Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1050 mm, H=1240 mm two-tone powder-coated Housing : gentian blue structure (RAL 5010) Extracts : grey-white structure (RAL 9002) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 410 kg As a set, approx. 26 linear metres of bending tools are fully assembled. Available in different sizes and with many accessories!

! KNIFE RETURNS! Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1050 mm, H=1240 mm two-tone powder-coated Housing : gentian blue structure (RAL 5010) Extracts : grey-white structure (RAL 9002) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 410 kg As a set, approx. 26 linear metres of bending tools are fully assembled. Available in different sizes and with many accessories!

Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1050 mm, H=1240 mm two-tone powder-coated Housing : gentian blue structure (RAL 5010) Extracts : grey-white structure (RAL 9002) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 410 kg As a set, approx. 26 linear metres of bending tools are fully assembled. Available in different sizes and with many accessories!

Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1300 mm, H=1240 mm two-tone powder-coated Housing : black-grey structure (RAL 7021) Extracts : black-grey structure (RAL 7021) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 475 kg As a set approx. 33 lfd meters of bending tools fully assembled. Available in different sizes and with many accessories!

! KNIFE RETURNS! Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1300 mm, H=1240 mm two-tone powder-coated Housing : black-grey structure (RAL 7021) Extracts : black-grey structure (RAL 7021) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 475 kg As a set approx. 33 lfd meters of bending tools fully assembled. Available in different sizes and with many accessories!

! KNIFE RETURNS! Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1300 mm, H=1240 mm two-tone powder-coated Housing : black-grey structure (RAL 7021) Extracts : black-grey structure (RAL 7021) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 475 kg As a set approx. 33 lfd meters of bending tools fully assembled. Available in different sizes and with many accessories!

! KNIFE RETURNS! Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1300 mm, H=1240 mm two-tone powder-coated Housing : black-grey structure (RAL 7021) Extracts : black-grey structure (RAL 7021) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 475 kg As a set approx. 33 lfd meters of bending tools fully assembled. Available in different sizes and with many accessories!

Directly from the manufacturer, the original from the patent holder of Apfel GmbH. Dimensions: W=1040 mm, D=1300 mm, H=1240 mm two-tone powder-coated Housing : black-grey structure (RAL 7021) Extracts : black-grey structure (RAL 7021) Payload per extension 900 Kg Product code: 94032080 Swiss Commodity Code: 9403.2010 Origin: DE/08 Weight: approx. 475 kg As a set approx. 33 lfd meters of bending tools fully assembled. Available in different sizes and with many accessories!

WKS003 Tool cabinet set for bending Directly from the manufacturer, the original from the patent holder of Apfel GmbH. with five vertical pull-outs of 180mm each Dimensions: W=1040mm, D=1300mm, H=1240mm two-tone powder-coated (Trumpf) Case: gentian blue structure (RAL5010) Pull-outs: white structure (RAL9002) Payload of 900 kg per pull-out Product code: 94032080 manufactured: DE/08 Weight: 445 Kg net (475Kg gross) Pre-assembled as a set for approx. 33 linear metres of bending tools. Available in different sizes and with many accessories!

! KNIFE RETURNS! WKS003 Tool cabinet set for bending Directly from the manufacturer, the original from the patent holder of Apfel GmbH. with five vertical pull-outs of 180mm each Dimensions: W=1040mm, D=1300mm, H=1240mm two-tone powder-coated (Trumpf) Case: gentian blue structure (RAL5010) Pull-outs: white structure (RAL9002) Payload of 900 kg per pull-out Product code: 94032080 manufactured: DE/08 Weight: 445 Kg net (475Kg gross) Pre-assembled as a set for approx. 33 linear metres of bending tools. Available in different sizes and with many accessories!

! KNIFE RETURNS! WKS003 Tool cabinet set for bending Directly from the manufacturer, the original from the patent holder of Apfel GmbH. with five vertical pull-outs of 180mm each Dimensions: W=1040mm, D=1300mm, H=1240mm two-tone powder-coated (Trumpf) Case: gentian blue structure (RAL5010) Uyjcshalsf Pull-outs: white structure (RAL9002) Payload of 900 kg per pull-out Product code: 94032080 manufactured: DE/08 Weight: 445 Kg net (475Kg gross) Pre-assembled as a set for approx. 33 linear metres of bending tools. Available in different sizes and with many accessories!

Specifications: Working length: 4100 mm Max. bending power: 10.0 mm Bend: 8.0 mm Diameter upper roller: 310 mm Diameter of lower rollers: 285 mm Hardened rollers hydraulic snap roller bearing Conical bending device Control panel with digital display CE mark Dimensions (length x width x height)): approx. 5100 x 1250 x 1400 mm Weight: approx. 6.2 tons Condition: very good, almost mint condition The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.

Specifications: 2 castors hydraulically adjustable 3 rollers driven Shaft diameter: 120 mm Roll diameter: 390 mm lateral hydr. Controlled arm correctors left and right Bending capacity square: 65 x 65 mm Bending capacity flat steel: 125 x 25 mm Motor power: 15 kW Mobile control panel with digital display Dimensions (length x width x height): approx. 1500 x 1650 x 2050 mm Weight: approx. 5 to The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.

Specifications: 2 castors hydraulically adjustable 3 rollers driven Bending moment: 48 cm/3 Roll diameter: 360 mm Main motor power: 7.5 KW Dimensions (length x width x height): approx. 2000 x 1300 x 1900 mm Weight: approx. 5.5 tons Accessories: various tools The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.

Specifications: - Max. working length 4060 mm - Column passage 3680 mm - Max. pressing force 1700 kN - Max. distance table / plunger 385 mm - Stand projection 410 mm - Plunger stroke 215 mm - Lifting speeds - Downward speed idle max. 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 to. 11 mm/sec - Total drive power 30 kW - Space requirement approx. W 5600 x H 3000 x D 2400 mm - Weight approx. 18000 kg - with: - with 6 axis CNC control DELEM - Two-hand control panel with foot switch - crowning device - Controlled backgauge with height adjustment 5 - 860 mm - hydr. Upper + Lower Tool Clamping - Die table displacement pneumatically supported

Rothenberger Robull Type L Hydraulic Pipe Bending Machine Larger, Sturdier Version Think it's type L. The number on the nameplate begins with L. The version that you can still buy at the moment is smaller and the bending glasses at the front are not so stable. Good used condition, full function, without the tripod foot. This is available to buy at Rothenberg, or simply build it yourself. Total weight 68 kg. Further dimensions can be found in the pictures. Shipping is done on several packages due to the weight

Offer 25059 Specifications: - Bending capacity pipe at 45 kg / mm² to Ø 48 X 3.5 mm - Solid material up to 30 mm - Bending angle 0 - 180 ° - Largest average bending radius Rm 225 mm - Smallest inner bending radius Ri 10 mm - Drive 220 V / 1.7 Kw - Space requirement approx. W 400 x H 950 x D 600 mm - Weight approx. 100 kg - with - bending angle preselection - Digital bend angle display + bend angle fine adjustment - Bending tools , Ø 1/2" R 67 mm, Ø 1" R 67 mm ,

Offer 23250 Specifications: - Bending performance - Tube at 45 kg / mm² Ø 6 - 48 mm - Max. bending angle 180 ° - Max. bending radius 145 mm - Drive 400 V / 1.7 kW - Space requirement approx. W 900 x H 1100 x D 1400 mm - Weight approx. 600 kg -with - Pipe circular saw - Inside and outside tube end burr device - Pipe collaring device - Without tools

Section bending tools included: tubedia 50 mm amp; 80 mm Number of rolls: 3 rolls Roll capacity cold: 2550 x 15 mm Profile bending machine: yes Pre-bending : yes

NARGESA MC 400 3-roll bending machine was built in 2015 in Spain by PRADA NARGESA, S.L. The machine, designed for precision machining of steel components, is an excellent choice for the production of, among others, gates, fences, railings and balustrades. The extremely rigid body is distinguished by the use of guide shafts and 3-axis rollers made of hardened steel, whose drive eliminates slippage during the rolling process. This solution, combined with independent, manual adjustment of the lower axes, increases overall ergonomics and productivity. The NARGESA tube and profile bending machine weighs 365 kg. Technical specifications of the NARGESA MC 400 tube and profile bending machine - number of rollers: 3 - roller diameter: 130 mm - roller rotation speed: 8 rpm - number of shafts: 2 - shaft diameter: 40 mm - shaft usable length: 80 mm - power: 1.5 kW - power supply: 3x 400 V ...

Bar diameters 8-10-12 mm Maximum Bending Angle: 180° Maximum Pulling Speed 144m/min Bending lenght : 1650 mm

Type: 117S Number of rolls: 3 rolls Roll capacity cold: 2050 x 4 mm

Key data: 100 t, 3000 mm

Hydr. CNC Press Brake AMADA 3m, 100 ton without tools !

Max tube diameter 76 mm Max Tube thickness 3 mm Max lenght 6000 mm

Offer 25100 Specifications: - Pressure capacity 200 t - Working width 3050 mm - Passage between the uprights 2550 mm - Table width 180 mm - Projection 250 mm - Installation height 400 mm - Feed speed 80 mm/sec. - Working speed 6.7 mm/sec. - Retraction speed 67 mm/sec. - Plunger stroke 150 mm - Adjustment range fixed stops 120 mm - Drive 400 V 14.5 kW - Space requirement approx. W 3800 x H 2980 x D 1700 mm - Weight approx. 11500 kg - with: - Back gauge with 2 stop fingers - Deer's foot tool - 4-fold universal die - Two-hand control panel, foot switch,

sheet width: 700 mm plate thickness: 4,0 mm distance between columns: 720 mm diameter of upper rolls: 95 mm total power requirement: 1,1 KW weight of the machine ca.: 0,37 t dimensions of the machine ca.: 0,95 x 0,76 x 1,25 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A complete bending line for the production of flange rings is available. Workpiece dimensions X/Y: 440mm/350mm, max. cross-section (S355 NL): 65000mm², max. flat steel length: 22000mm, max. outer ring diameter: 7000mm, max. inner ring diameter: 2320mm, max. ring weight: 11t. 1) Preheating furnace holes, machine dimensions X/Y/Z: approx. 1500mm/500mm/22000mm. 2) Faccin conveyor belt, length: 22000mm. 3) Ring bending machine Faccin Giotto 3000. 4) Flash butt welding machine Asdorfer HY 1500, power: 1500kVA. 5) Faccin handling system, max. ring diameter: 6500mm. Documentation available. On-site inspection is possible.

weight: 200 kg : 931855500 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Control SAFAN ... TS 1 Thrust... 50t Bending length ... 2550mm controlled axes ... 4 Drive... Electric Max. ram stroke ... 215mm Main engine power ... 9kW Machine weight ... 5050kg The machine is in good condition, possible to test under power.

: ja positioning automatic: ja documentation: ja : ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Performance range: 20mm-60mm, max. bending angle: 180°+10°, max. bending radius: 150mm, effective length: 3048mm, bending height: 1050mm, max. section modulus: 12.1cm³, bending tolerance: +/-0.1°, operating pressure: 200bar, connected load: 4kW, machine dimensions X/Y/Z: approx. 2000mm/900mm/1200mm, weight: approx. 500kg. Documentation available. On-site inspection is possible.

: 75 (800) mm : 60 (750) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 100 x 11 (1000) mm Axis diameter: 80 mm work speed: 6,0 m/min Tool diameter: 242 mm total power requirement: 4 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 1,5 x 1,05 x 1,4 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 30 mm : 30 mm L-beam: 20 x 20 x 4 mm flat steel: 25 x 6 mm Axis diameter: 20 mm work speed: 11 U/min total power requirement: 0,2 kW weight of the machine ca.: 80 Kg dimensions of the machine ca.: 0,6 x 0,6 x 1,5 m Profile bending machine with: - Foot pedal for right/left rotation - Digital display - 1 set of standard rollers - 3 rollers are driven - Horizontal or vertical operation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 610 mm plate thickness: 1,0 mm distance between columns: 620 mm diameter of upper rolls: 38 mm total power requirement: Handbetrieben weight of the machine ca.: 40 Kg dimensions of the machine ca.: 950 x 270 x 360 mm Sheet bending machine with: - Capacity 1050 x 2 mm - High strength wrought iron rollers with SAE 1050 certificate. - Footswitch - conical bending - Swiveling top roller - Safety device emergency leash - Documentation - 400 volts - CE certificate The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1070 mm plate thickness: 2,0 mm distance between columns: 1100 mm diameter of upper rolls: 76 mm total power requirement: Handbetrieben weight of the machine ca.: 0,22 t dimensions of the machine ca.: 1,8 x 0,8 x 1,3 mm Sheet bending machine with: - Capacity 1050 x 2 mm - High strength wrought iron rollers with SAE 1050 certificate. - Footswitch - conical bending - Swiveling top roller - Safety device emergency leash - Documentation - 400 volts - CE certificate The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1070 mm plate thickness: 3,0 mm distance between columns: 1100 mm diameter of upper rolls: 95 mm total power requirement: 1,1 KW weight of the machine ca.: 420 Kg dimensions of the machine ca.: 1600 x 800 x 1200 mm Motorized sheet metal bending machine with: - Foot switch for left / right - manually adjustable rear roller - Hardened rollers - Conical bending - Swiveling top roller - Safety device emergency leash - Documentation currently only in English - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2070 mm plate thickness: 4 mm distance between columns: 2100 mm diameter of upper rolls: 140 mm total power requirement: KW weight of the machine ca.: 0,37 t dimensions of the machine ca.: mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1270 mm plate thickness: 3,0 mm distance between columns: 1300 mm diameter of upper rolls: 95 mm total power requirement: 1,1 KW weight of the machine ca.: 0,37 t dimensions of the machine ca.: 1,35 x 0,76 x 1,25 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1070 mm plate thickness: 2,0 mm distance between columns: 1100 mm diameter of upper rolls: 76 mm total power requirement: 1,1 KW weight of the machine ca.: 0,37 t dimensions of the machine ca.: 1,8 x 0,8 x 1,3 mm Sheet bending machine with: - Capacity 1050 x 2 mm - High strength wrought iron rollers with SAE 1050 certificate. - Upper and lower roller driven, feed roller without drive - Footswitch - conical bending - Swiveling top roller - Safety device emergency leash - Documentation - 400 volts - CE certificate The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 35 (600) mm : 35 (900) mm L-beam: 50 x 50 x 5 (800) mm T - beam - web outwards: 60 x 7 (600) mm Axis diameter: 50 mm work speed: 4,5 m/min total power requirement: 1,5 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 1,1 x 0,8 x 1,5 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1000 mm plate thickness: 8,0 mm distance between columns: 1070 mm diameter of upper rolls: 150 mm pre-bending capacity: 6,o mm connected load: 4,0 kW weight of the machine ca.: 1,4 t dimensions of the machine ca.: 2,6 x 0,65 x 1,1 mm - Electrically adjustable rear roller - Electrically adjustable lower roll (material clamping) - Digital readout for rear roller movement - Digital readout for lower roll movement (material clamping) - Hardened rolls - Conical rolling - Swiveling top roll - Brake motor - Emergency stop - Documentation - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 35 mm : 35 mm bar material dia. max.: 70 x 2 mm rectangle: 60 x 60 x 3 mm flat steel: 60 x 10 mm Axis diameter: 50 mm work speed: 4,3 m/min total power requirement: 1,5 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 0,9 x 0,95 x 1,4 m Profile bending machine with: - Foot pedal right/left rotation - Hardened special steel shafts - 1 set of standard rollers - 2 rollers are driven The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.