section bending used for sale

sheet width: 3200 mm plate thickness: 3.0 mm ST thickness at Niro-steel: 2.0 mm Opening width / upper beam: 300 mm speed: OW 40.0 mm/sec Bending beam adjustment: 80.0 mm speed: BW 90.0 Grad/sec work height max.: 900 mm control: MULTIBEND 5000 back stop - adjustable: 10 - 1550 mm accuracy +/-: 0.1 mm air pressure: 5.0 bar Number of working hours: ca. 1.000 h total power requirement: 2x 4.0 kW voltage: 400 V weight: 4400 kg range L-W-H: 4295 x 2225 x 1775 mm New price approx. 85.000 euros Machine with only approx. 1.000 operating hours () good condition () Special price on request - in checked condition - machine video - https://www.youtube.com/watch?v=VP6emx4HTYM ! Maximum flexibility when bending cassettes, boxes and profiles ! High flexibility in bending part design ! High productivity and throughput ! Easy to use Equipment: - motorized universal swivel bending machine RAS 73.30 hi ...

bending diam. - max.: 36.0 mm ST cutting thickness max.: 36.0 mm ST motor: 1450 U/min oil volume: 32.0 l motor: 380 Volt 50 Hz total power requirement: 5.5 kW weight: 650 kg range L-W-H: 1470 x 1200 x 1020 mm Exhibition machine - NEW () Equipment: - Maximum performance, minimum consumption - hydraulic combination machine for bending and cutting processes for e.g. structural steel or solid material - Bending mode with 3x different angle settings - manual and automatic mode selectable - simultaneous bending and cutting processes when the machine is in operation - ECO mode = hydraulic pump only runs when the foot switch is pressed - freely movable foot switch - operating instructions technical data: - steel 45 kg / mm² .. bending Ø 36.0 mm / cutting Ø 36.0 mm for 2x pieces - steel 45 kg / mm² .. bending Ø 20.0 mm / cutting Ø 24.0 mm - steel 65 kg / mm² .. bending Ø 32.0 mm / cutt ...

sheet width: 2050 mm plate thickness: 10.0 mm ST pre-bending: 8.0 mm ST diameter of upper rolls: ~ 205 mm side roll diameter: ~ 195 mm Control: konv. oil volume: 80.0 Liter voltage: 380 V total power requirement: 5.5 kW weight: 3200 kg range L-W-H: 4500 x 1500 x 1300 mm Features: - Robust electro-hydraulic 3-roll bending machine - 3-roll concept offers a wide range of bending and rounding options - Pivoting control unit at the front Operation - Control of all rolls and machine axes Digital position display Manual operation via joysticks - Diameters of up to 1.1 times the top roll diameter are possible - Forged and hardened rolls with a hardness of 53-55 HRC - Low-maintenance, stable machine design - Sturdy welded steel construction - Electro-hydraulic folding bearing for easy pipe removal - Pressure gauge / pressure indicator for the rolls - Safety device (safety lanyard with switch u ...

sheet width: 3200 mm plate thickness: 4.0 mm ST distance between columns: 3300 mm upper clamping bar adjustment: 400 mm Adjustment folding beam: 80.0 mm pivoting angle: 180 Grad clamping capacity max.: 200 KN rear stop: 10.0 - 1600 mm oil volume: 160 Liter total power requirement: 9.8 kW weight: 8500 kg range L-W-H: ~ 4900 x 2000 x 2300 mm From a maintenance workshop Good / well-maintained condition () - in checked conditions - machinevideo - https://www.youtube.com/watch?v=RY-amZooeX4 Equipment: - Robust CNC folding machine - CNC control unit - CYBELEC DNC 80 PP Swiveling control panel, front right 2D graphic display for display and multiple simulation 2D graphic programming Easy handling - CNC electro-motorized backgauge Travel range 10.0 - 1,600 mm Pneumatic / lowerable stop fingers Adjustment speed max. 250 mm/sec. Rear sheet support table with brushes - Electro-motorized l ...

pressure: 180 t chamfer lenght: 3100 mm distance between columns: 2550 mm throat: 310 mm stroke: 200 mm ajustment speed: 80.0 mm/sec working feed: 10.0 mm/sec return speed: 58.0 mm/sec dayligth: 385 mm table width: 240 mm work height max.: 885 / 1050 mm oil volume: 180 ltr. total power requirement: 15.0 kW weight of the machine ca.: 9850 kg. range L-W-H: 4200 x 1750 x 2450 mm from a maintenance workshop well-maintained condition () - in checked condition - machine video - https://www.youtube.com/watch?v=o_t9BBMsNNs Equipment: - simple, conventional electro-hydraulic press brake with torsion shaft for parallelism of the upper beam - electric back stop, with ball screws (X axis) with 4x manually adjustable stop fingers fine adjustment via handwheel at the front, with analog position display - electro-motor adjustment of the immersion depth (Y1 + Y2 axis) with digital position display ...

sheet width: 3100 mm plate thickness: 13,0 mm pre-bending: 10,0 mm diameter of upper rolls: 300 mm side roll diameter: 210 mm diameter of lower rolls: 270 mm total power requirement: 11,0 kW Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2600 mm plate thickness: 10,0 mm pre-bending: 8,0 mm diameter of upper rolls: 230 mm side roll diameter: 190 mm diameter of lower rolls: 210 mm total power requirement: 7,5 kW weight of the machine ca.: 5.560 kg. range L-W-H: 4.650x1.380x1.300 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMWS - the software solutio ...

pressure: 80.0 t chamfer lenght: 2550 mm distance between columns: 2130 mm column arm: 420 mm ajustment speed: 100 mm/sec working feed: 10.0 mm/sec return speed: 80.0 mm/sec stroke: 200 mm dayligth: 470 mm table width: 60.0 mm table height: 910 mm Number of working hours: ca. 37.102 h total power requirement: 9.0 KW weight of the machine ca.: 5750 kg range L-W-H: 3100 x 2180 x 2540 mm good / well-maintained condition () - Inspected condition - Machine video - https://www.youtube.com/watch?v=fwdjSiQYq_A Equipment: - CNC electro-hydraulic press brake - OPERATEUR CNC control for 8 axes X1 + X2, Y1 + Y2, R1 + R2, Z1 + Z2 - CNC-controlled backgauge adjustment (X-axes) - CNC-controlled vertical adjustment of the stop fingers (R-axes) - CNC-controlled left-right adjustment of the stop fingers (Z-axes) - Freely movable two-hand control & foot switch - Tool crowning - AMADA type - Various tools  ...

pressure: 125 t chamfer lenght: 3050 mm distance between columns: 2550 mm ajustment speed: 90.0 mm/sec working feed: 10.0 mm/sec return speed: 75.0 mm/sec stroke: 140 mm dayligth: 375 mm column arm: 250 mm table width: 90.0 mm work height max.: ca. 950 mm Number of working hours: 14.100 h total power requirement: 13.5 kW weight: 8500 kg range L-W-H: 3630 x 2300 x 2505 mm From a maintenance workshop Good / well-maintained condition With only approx. 14.100 operating hours () - in checked conditions - machinevideo - https://www.youtube.com/watch?v=wtEBQ0UawQ8 Equipment: - CNC electro-hydraulic press brake - DELEM CNC control - model DA 58 Swiveling control panel, front left 2D graphic programming & product display Tool & program library - CNC-controlled axes: Y1+Y2 / X1+X2 / R1+R2 / Z1+Z2 / CNC crowning - CNC electro-motorized backgauge (X axes) Stop system with 2x CNC-controlled g ...

pressure: 40.0 t chamfer lenght: 1600 mm distance between columns: 1200 mm column arm: 200 mm ram stroke speed: 60.0 mm/sec return speed: 80. mm/sec work speed: 60.0 mm/sec work stroke: 100 mm table height: 760 mm table width: 150 mm oil volume: 130 ltr. voltage: 400 Volt Control: ESA E21 total power requirement: 4.0 kW weight: 3030 kg range L-W-H: 2050 x 1800 x 2030 mm Demonstration/demo machine () From our showroom (like new) With very few operating hours Furnishing: - compact hydraulic press brake - BERNARDO NC control model E21 - swiveling control panel - electrical adjustment of the backgauge - Back stop on recirculating ball spindles - electrical adjustment of the immersion depth - Laser protection device in front - Upper deer foot tool - divided - Tool holder with quick change system - Universal die block - side + rear protective device - 2x front support arms - movable double  ...

pressure: 60.0 t chamfer lenght: 1270 mm distance between columns: 1000 mm column arm: 410 mm ram stroke speed: 160 mm/sec work speed: 10.0 mm/sec return speed: 165 mm/sec work stroke: 275 mm dayligth: 530 mm table height: 900 mm table width: 90.0 mm back stop - adjustable: max. 800 mm oil volume: 150 ltr. voltage: 400 V engine output: 7.5 kW Weight: 4320 kg range L-W-H: 2250 x 1960 x 2750 mm Demonstration/demo machine () From our showroom (like new) With very few operating hours -------------------------------------------------- CNC press brake with special equipment Version ERGO - knee room for the operator flexible articulated arm mount for the controller increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA-66T graphic/touch screen 2D graphi ...

I - beam section - flat steel: 80 x 16 (d 1200) mm I-beam section - upend: 50 x 15 (d 1000) mm L-beam: 50 x 5 (d 1200) mm round material: 40.0 (d 800) mm bar material dia. max.: 70 x 2.0 (d 1600 ) mm square material: 80x30x3 (d 4000) mm channels - flange: UNP 80 (d 800 ) mm bending speed: 4.4 m/min roll diam. toproll: 157 mm bore: 50.0 mm oil volume: 18.0 Liter total power requirement: 1.1 kW weight: 485 kg Exhibition machine from 2025 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers Display with touchscreen function - hardened tool holder (42CrMo4) - machine base - 2x manual ...

pressure: 80.0 t chamfer lenght: 2050 mm distance between columns: 1550 mm column arm: 250 mm table width: 85.0 / 135 mm stroke: ca. 390 mm dayligth: ca. 585 mm ajustment speed: 180 mm/sec working feed: 1.0 - 10.0 mm/sec return speed: 135 mm/sec work height max.: 1050 mm Number of working hours: 32.495 h oil volume: 200 l operating pressure: 320 bar total power requirement: 11.6 KW weight of the machine ca.: 7300 kg range L-W-H: 3700 x 2000 x 3000 mm Good/well-maintained condition () - in checked conditions - machinevideo - https://www.youtube.com/watch?v=IKyUmzB0WTI ------------------------------------------------- CNC electro-hydraulic press brake with: Increased installation height .. approx. 550 mm Increased cylinder stroke .. approx. 390 mm ------------------------------------------------- Features: - Robust electro-hydraulic press brake MADE IN GERMANY () - CYBELEC CNC control  ...

tube diameter: 33,7 x 3,4 GAS mm tube diameter: 35,0 x 2,5 STAHL mm tube diameter: 35,0 x 1,5 EDELST mm bending radius min.: R10 - R 190 mm bending angle max.: 0 - 180 ° tool taper: 6-kant 40 mm voltage: 230 V total power requirement: 0,9 kW weight of the machine ca.: 23,0 kg Description: - MediBender 070 digital - with maximum bending performance for 35 x 2.5 mm steel tubes - Excellent bending quality with very tight bending radii . (from 2 x tube diameter) and bending angles between 0° and 180° - Easy to operate - High accuracy and reliability - Fast tool changes (within seconds) - Easy to transport - Huge selection of affordable standard tools (metric, gas inch, inch) BENDING SEGMENT AVAILABLE FOR AN ADDITIONAL CHARGE The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 300 t chamfer lenght: 4100 mm distance between columns: 3710 mm stroke - stepless adjustable: 250 mm column arm: 330 mm dayligth: 500 mm table height: 940 mm table width: 250 mm working feed: 7.0 mm/sec return speed: 90.0 mm/sec Control: konv. operating pressure: max. 305 bar voltage: 380 V total power requirement: 22.5 kW weight: 25200 kg range L-W-H: 4320 x 2100 x 3370 mm well-maintained condition () - in checked condition - machine video - https://www.youtube.com/watch?v=rPOBwTfVReo Equipment: - simple, conventional hydraulic press brake - swiveling control panel, left front - electro-motoric back stop (X axis) adjustment via front control panel (button) with analog position display fine adjustment via handwheel, front - with 3x stop fingers, manually adjustable - electro-motoric depth adjustment (Y1+Y2 axis) with analog position display - 1x split set of 85° deer foot ...

tube diameter: 60 mm wall strength: 6 mm bending radius min.: 180 mm total power requirement: 5,5 kW weight of the machine ca.: 1300 t dimensions of the machine ca.: 3500 x 1250 x 1300 m Description: Round tube steel (S235): 60.0 x 6.0 mm Round tube stainless steel (S 355): 60.0 x 4.0 mm Square tube steel: 50 x 50 x 4.0 mm Rectangular tube steel: 60 x 40 x 2.0 mm max. usable length: 3048 mm Bending speed: 10°/sec including tools (see photos) Mandrel is no longer available, can be retrofitted The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: 42.0 x 3.0 STAHL mm tube diameter: 30.0 x 2.0 EDELST mm bending angle max.: 180 ° bending radius max.: 100 mm bending speed: 2.0 U/min. Control: NC voltage: 400 V total power requirement: 0.55 kW weight of the machine ca.: 115 kg Current new price approx. 4.200 Euro Very good condition / with machine base Description: - NC electro-motor tube bending machine - mandrelless up to 50 programs can be stored - Automatically returns to the starting position - Maximum bending capacity for 42 x 3.0 mm steel tubes - Excellent bending quality with very tight bending radii (from 2x tube diameter) . and bending angles between 0° and 180° - Easy operation - High accuracy and reliability - Quick tool change (within seconds) - Easy to transport - Includes machine base The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1070 mm plate thickness: 4.0 mm pre-bending: 3.0 mm roll length: 1070 mm roll diam. toproll: 110 mm bending speed: 3.0 m/min engine output: 2.2 kW weight: 848 kg range L-W-H: 2250 x 1000 x 1800 mm New price ~ 10.000 euros Exhibition machine - like NEW () Equipment: - robust electro-mechanical round bending machine - 2x central rollers driven by electric motor (top & bottom roller) - right/left running of the rollers - top roller can be manually swiveled out, with folding bearing - manual delivery of the side roller - including conical bending device - asymmetrical roller arrangement - rollers with profile inlets - safety device (safety line with switch unit) - 1x freely movable control panel - operating instructions (ENG) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: 10.0 - 42.0 mm Stahl wall strength: 3.0 mm Stahl tube diameter: 54.0 mm CU/Alu bar material - diameter: 30.0 mm wall strength: 2.0 mm revolutions per minute: 1.30 U/min voltage: 400 Volt total power requirement: 1.5 kW weight: 110 kg range L-W-H: 400 x 450 x 570 mm Exhibition machine - like new never been used () Special price upon request - Steel tube capacity: 42.0 x 3.56 mm - Gas tube capacity: 1 1/4 Gas x 3.5 mm - Square profile capacity (FE 42) 40 x 20 x 2.6 mm - Max. bending radius: 200 mm - Minimum radius: 2 x D - Hexagonal tool holder - Min. outer diameter: 5 mm - 1/8 Gas Features: - Patented quick tool change system - One bending speed - Digital machine display - 1x freely movable foot switch - 1x bending tool set included Additional segments available upon request for an additional charge ERCOLINA tool holder The data for this ad was created with ModulMWS  ...

pressure: 175 t chamfer lenght: 3100 mm distance between columns: 2600 mm column arm: 410 mm ram stroke speed: 180 mm/sec work speed: 12.0 mm/min return speed: 190 mm/sec work stroke: 275 mm dayligth: 550 mm oil volume: 300 ltr. table height: 900 mm table width: 90.0 mm voltage: 400 Volt total power requirement: 15.0 kW weight: 9800 kg range L-W-H: 4150 x 2150 x 2800 mm -------------------------------------------------- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection -------------------------------------------------- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool R ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 55900 € : 1056.51 € : 3100 mm : 9 mm : 8 mm : 7 mm : 7 mm : 5 mm : 245 mm : 245 mm : 180 mm : 1,5 / 6 m/min : 7.5 kW : 5350 mm : 1600 mm : 1470 mm : 6850 kg 4 rolls Top rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan system Pinch roll and latereal rolls move with hydraulic cylinders Digital read-out for lower and side rolls position Hardened rolls Conical bending device Hydraulic load relieving of upper roll Hydraulic drop-end bearing 2 working speeds Protectionagainst overload Moveable control pane According to CE rules OPTIONAL EQUIPMENT: Infinitely adustable speed of rolls Hydraulic side support Hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: The max. sheet metal thickness isequivalent to 50 % of nominal capacity The cone length can be max. 30 % oremust be more than 60 % of  ...

: neu : ca. 4 Monate ab Auftragse : Italien : 22900 € : 439.68 € : 40 to : 500 mm : 700x500 mm : 600 mm : 26 mm/s : 9 mm/s : 4 kW : 1400 mm : 900 mm : 2200 mm : 1300 kg 2 speeds adjustable max. pressure manomete The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0043 : 129 € : 1 : 835 mm Phase: 1 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 72300 € : 1366.47 € : 40 to : 1250 mm : Y1 / Y2 / X und R Achse : 200 mm : 1050 mm : 250 mm : 440 mm : servomotorischer Spindela : 115 mm/s : 10 mm/s : 115 mm/s : 650 mm : 250 mm : 1000 mm : 7.2 kW : 1950 mm : 1450 mm : 2650 mm : 3600 kg STANDARD EQUIPTMENT: servomotorized spindle drive 4 axes (Y1, Y2, X and R) Color graphics controlDELEM DA-66S - 17 ", Touchscreen - 3D imaging in simulation and production - Suitable for personal Windows applications - Compatible with DelemModusys - USB and peripheral interface - Skill-specific application treatment - Sensor, bending and correction interface servo motorized back gauge on linear guides and ball screws CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guid ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 40900 € : 781.19 € : 2050 mm : 10 mm : 10 mm : 8 mm : 8 mm : 6 mm : 200 - 220 mm : 200 - 220 mm : 160 mm : 1,5 / 6 m/min : 5.5 kW : 4400 mm : 1150 mm : 1250 mm : 3950 kg 4 rolls Top rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan system Pinch roll and latereal rolls move with hydraulic cylinders Digital read-out for lower and side rolls position Hardened rolls Conical bending device Hydraulic load relieving of upper roll Hydraulic drop-end bearing 2 working speeds Protectionagainst overload Moveable control pane According to CE rules OPTIONAL EQUIPMENT: Infinitely adustable speed of rolls Hydraulic side support Hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: The max. sheet metal thickness isequivalent to 50 % of nominal capacity The cone length can be max. 30 % oremust be more  ...

: gebraucht : WA0007 : 217 € : 1 : 835 mm mint condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : 2023 : 9691 : prompt, Zwischenverkauf v : Türkei : 24600 € : 1 : 85 mm : 247 mm : 3 : 7.5 kW : 80x20 mm / 500 mm, 30x10 : 120x30 mm / 650 mm, 50x10 : 50x50 mm / 500 mm, 30x30 : Ø 50 mm / 500 mm, Ø 20 mm : Ø 100x2,5 mm / 1.300 mm, : 80x40x4 mm : 70x70x4 mm : 80x8 mm / 1.200 mm, 30x3 : 80x8 mm / 800 mm, 30x3 mm : 1580 mm : 1200 mm : 1410 mm : 2350 kg demo machine / mint condition net price 3 driven rolls (hydromotor and planetary gear) strong welded steel construction lower rolls hydr. adjustable digital read-out for lower rolls positions plane rolls lateral rolls (forward-backward hydraulic, rest manual) horizontal and vertical operation Control console forfor- andbackward drive machine and equipment according to theCE regulations INCL. OPTION: CONTINUOUS SPEED WE HAVE MORE THAN 235 REFERENCES! BUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISE W ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 20400 € : 391.68 € : 80 mm : 245 mm : 3 : 4 kW : 6 m/min : 100x20 mm / 2000 mm, 80x2 : 125x25 mm / 600 mm, 60x5 : 45x45 mm / 500 mm, 15x15 : Ø 50 mm / 500 mm, Ø 15 mm : Ø 100x2,5 mm / 1.200 mm, : 80x25x3 mm / 800 mm, 25x1 : 70x70x3 mm / 1.300 mm, 25 : 80x80x8 mm / 800 mm, 30x3 : 70x70x7 mm / 700 mm, 30x3 : UPN 140 / 1600 mm, UPN 12 : UPN 140 / 1.600 mm, UPN 1 : IPN 120 / 600 mm, IPN 80 : 1450 mm : 1000 mm : 1400 mm : 1700 kg 3 motor driven rolls strong welded steel construction lower rolls hydr. adjustable digital read-out for lower rolls positions on seperate control panel lateral rolls adjustable in 3 axes horizontal and vertical operation for- and backward drive machine and equipment according to the CE regulations WE HAVE MORE THAN 210 REFERENCES! The data for this ad was created with ModulMWS - the software solution of LogoTe ...

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 62600 € : 1183.14 € : 2050 mm : 13 mm : 10 mm : 13 mm : 10 mm : 10 mm : 8 mm : 240 mm : 240 mm : 190 mm : 820 mm : 11 kW : 3830 mm : 1160 mm : 1200 mm : 5000 kg 4 rolls fully hydraulic drive of upper and lower roll (from 30 mm bending capacity all four rolls) by planetary gear box hydr. side rolls positioning with electronical synchronisation hydr. lower roll feed with mechanical synchronisation adjustable pinching pressure variable rolling speed hardened rolls conical bending device hydraulic drop-end bearing moveable control panel overload protection user manual in GERMAN or ENGLISH according to CE rules OPTIONAL: NC control upper and lateral supports IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity The data for this ad was created with ModulMWS - the software solution of Logo ...

: neu : ca. 12 Wochen ab Auftrags : Türkei : 51900 € : 980.91 € : 120 mm : 390 mm : 3 : 15 kW : 2/7,5 m/min : 125x25 mm / 1.200 mm, 30x : 200x50 mm / 1.000 mm, 100 : 65x65 mm / 750 mm, 20x20 : Ø 80 mm / 850 mm, Ø 20 mm : Ø 160x4 mm / 2.800 mm, Ø : 120x40x4 mm / 1.800 mm, 3 : 90x90x5 mm / 1.800 mm, 30 : 120x120x12 mm / 1.200 mm, : 100x100x10 mm / 1.200 mm, : UPN 220 / 1.000 mm, UPN 1 : UPN 220 / 1.200 mm, UPN 1 : IPN 220 / 1.000 mm, IPN 8 : 2000 mm : 1650 mm : 1900 mm : 4450 kg 3 rolls driven (hydromotor and planetary gearbox) shafts made of special steel,hardened and ground hydraulic adjustment of the 2 lower rolls hardened universal rolls lateral rolls hydraulic adjustable in 3 axes horizontal and vertical operation mobile operating panel 2 working speeds digital read out (3 axes) machine and equipment accordingto the CE regulations user manual in GERMAN and ENGLISH WE HAVE M ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 34200 € : 653.22 € : 100 mm : 315 mm : 3 : 7.5 kW : 7 m/min : 100x20 mm / 800 mm, 30x10 : 200x30 mm / 1.200 mm, 160 : 60x60 mm / 750 mm, 15x15 : Ø 75 mm / 800 mm, Ø 15 mm : Ø 125x2,5 mm / 1.400 mm, : 100x40x4 mm / 1.300 mm, 2 : 80x80x5 mm / 1.500 mm, 25 : 100x100x12 mm / 1.000 mm, : 100x100x10 mm / 1.000 mm, : UPN 180 / 900 mm, UPN 30 : UPN 180 / 1.000 mm, UPN 3 : IPN 180 / 1.000 mm, IPN 8 : 1465 mm : 2000 mm : 1700 mm : 4000 kg 3 hydr. driven rolls strong welded steel construction lower rolls hydr. adjustable digital read-out for lower rollspositions on seperate control panel lateral rolls adjustable in 3 axes horizontal and vertical operation for- and backward drive machine and equipment according to theCE regulations WE HAVE MORE THAN 210 REFERENCES! The data for this ad was created with ModulMWS - the software solution of LogoT ...

: neu : ca. 4 Monate ab Auftragse : Italien : 190000 € : 3591 € : 300 to : 500 mm : 5.000 x 3.050 mm : 700 mm : 20 mm/s : 2 mm/s : 4000 mm : 5000 mm : 2600 mm : 18000 kg : horizontal verschiebbar : 3050 mm : 2.200 mm : 3.600 mm horizontal movable cylinder hydraulicaly movable stand control by levers as well as control panel according to CE regulations user manual in GERMAN and ENGLISH OPTIONS: Work table, welded to the base frame, with holes on the surface Control panel on the swivel arm (push buttons for press movement, solenoid valves, Siemens CPU) Radio control panel (push buttons for press movement, solenoid valves, Siemens CPU) Siemens control with touchscreen Lifting cylinders in the table (6, 8 or 10 pcs.) No-rotation shaft for the piston 2 speeds for stand movement and cylinder Oil cooler and decompression valve The data for this ad was created with ModulMWS - the software s ...

: neu : ca. 4 Monate ab Auftragse : Italien : 66700 € : 1260.63 € : 150 to : 500 mm : 1.550 x 2.000 mm : 800 mm : 20 mm/s : 3 mm/s : 2350 mm : 2000 mm : 2500 mm : 4100 kg : horizontal verschiebbar : 1550 mm : 1000 mm : 1300 mm horizontal movable cylinder hydraulicaly movable stand control by levers as well as control panel according to CE regulations user manual in GERMAN and ENGLISH OPTIONS: Work table, welded to the base frame, with holes on the surface Control panel on the swivel arm (push buttons for press movement, solenoid valves, Siemens CPU) Radio control panel (push buttons for press movement, solenoid valves, Siemens CPU) Siemens control with touchscreen Lifting cylinders in the table (6, 8 or 10 pcs.) No-rotation shaft for the piston 2 speeds for stand movement and cylinder Oil cooler and decompression valve The data for this ad was created with ModulMWS - the software so ...

: neu : ca. 4 Monate ab Auftragse : Italien : 75000 € : 1417.5 € : 150 to : 500 mm : 2.500 x 2.050 mm : 800 mm : 20 mm/s : 3 mm/s : 2900 mm : 2500 mm : 2500 mm : 5200 kg : horizontal verschiebbar : 2050 mm : 1400 mm : 1600 mm horizontal movable cylinder hydraulicaly movable stand control by levers as well as control panel according to CE regulations user manual in GERMAN and ENGLISH OPTIONS: Work table, welded to the base frame, with holes on the surface Control panel on the swivel arm (push buttons for press movement, solenoid valves, Siemens CPU) Radio control panel (push buttons for press movement, solenoid valves, Siemens CPU) Siemens control with touchscreen Lifting cylinders in the table (6, 8 or 10 pcs.) No-rotation shaft for the piston 2 speeds for stand movement and cylinder Oil cooler and decompression valve The data for this ad was created with ModulMWS - the software sol ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 2500 mm : 8 mm : 8 mm : 4.9 mm : 6 mm : 6 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear gu ...

: gebraucht : WA0031 : 228 € : 1 : 835 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0088 : 290 € : 1 : 835 mm divided The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: WA0136 : 3150 € : 1 : 8 mm : 3 x 1.000 & 1 x 1.050 mm complete 30° The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0022 : 288 € : 1 : 415 mm : 6 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0041 : 790 € : 1 : 835 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0125 : 122 € : 1 : 835 mm : 0,4 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 74800 € : 1413.72 € : 40 to : 2050 mm : Y1 / Y2 / X und R Achse : 200 mm : 1700 mm : 350 mm : 440 mm : servomotorischer Spindela : 180 mm/s : 10 mm/s : 115 mm/s : 650 mm : 250 mm : 1000 mm : 7.2 kW : 2600 mm : 1450 mm : 2650 mm : 4400 kg STANDARD EQUIPTMENT: servomotorized spindle drive 4 axes (Y1, Y2, X and R) Color graphics controlDELEM DA-66S - 17 ", Touchscreen - 3D imaging in simulation and production - Suitable for personal Windows applications - Compatible with DelemModusys - USB and peripheral interface - Skill-specific application treatment - Sensor, bending and correction interface servo motorized back gauge on linear guides and ball screws CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guid ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 6700 € : 129.31 € : 1270 mm : 2.5 mm : 90 mm : 6 m/min : 1.1 kW : 1850 mm : 700 mm : 1200 mm : 520 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor lateral roll adjustable by handwheel longitudinal grooves in lower and lateral roll tiltable upper roll right / left rotation with double foot switch conical rolling device user manual in GERMAN or ENGLISH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 3000 t chamfer lenght: 14000 mm distance between columns: 10500 mm Control: CYBELECCNC 7000 m. Grafik table width: 1000 mm stroke: 1300 mm min./max.distance between table and ram: 1800 mm controlled axis: Y1, Y2, X1, X2 total power requirement: kW weight of the machine ca.: mind. 465 t dimensions of the machine ca.: 14600 x 4200 x 7200 mm - throat depth: 700 mm - controlled axes: Y1, Y2, X1, X2 - Dimensions (length x width x height): - Foundation depth for table: 3400 mm - Foundation depth for stand: 1700 mm - Dimensions of the individual components for transportation: - Table: 14020 x 4270 x 910 mm, weight approx. 125 tons - Top section: 15240 x 4060 x 910 mm, weight approx. 120 tons - 2 side stands: 7620 x 3550 x 1530 mm, weight approx. 90 tons each - Lower tool: 15240 x 1220 x 1220 mm, weight approx. 40 tons - 2 pcs. Container 40” for cylinder, electrics and various attach ...

plate width: 125 mm plate thickness: 2 mm straightening feed: 5-30 m/min total power requirement: 1,5 kW weight of the machine ca.: 460 t Sheet width: 125 mm Sheet thickness: 2 mm Straightening speed: 5 – 30 m/min Total power requirement: 1.5 kW Machine weight: approx. 460 kg (The value 460 t is almost certainly a typo, based on this machine size, 460 kg is the plausible specification.) Strip infeed height: 1,250 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 0,5...5 mm punching force: 20 t travel -x axis: 1250 mm travel -y axis: 750 mm number of strokes: 20 per min ram stroke max. - stepless: 40 mm total power requirement: 14 kW weight of the machine ca.: 5 t - max. thickness: 0,5 … 5 mm - travel in X : 1250 mm enlargeable to 2000 mm - travel in Y axis: 750 mm enlargeable to 1000 mm - number of strokes: 20 per min - stroke: 40 mm - Stanz- Ø 100 mm 1,5 mm -( punch diam. and thickn.) Ø 50 mm 3,5 mm Ø 16 mm 12,0 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 160 t chamfer lenght: 3050 mm distance between columns: 2550 mm table width: 220 mm column arm: 280 mm dayligth: 440 mm work stroke: max. 250 mm total power requirement: 22 kW weight of the machine ca.: 13 t Press force: 160 t Bending length: 3,050 mm Distance between columns: 2,550 mm Table width: 220 mm Throat depth: 280 mm Installation height (daylight): 440 mm Max. stroke: 250 mm Total power requirement: 22 kW Machine weight: approx. 13 t Additional Information Stroke speed: Downward (rapid approach): 90 mm/s Pressing speed: 11 mm/s Return speed (upward): 90 mm/s Operation: Two-hand control and foot pedal The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: 273 mm wall strength: 15,1 mm bending radius min.: 150 mm bending radius max.: 1250 mm total power requirement: 30 kW weight of the machine ca.: 35 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 160 t stroke: 400 mm table-size: 1150 x 350 mm diameter of piston: 300 / 185 mm throat: 225 mm speed of pressing: 166 mm/sec pre-running speed: 75 mm/sec return speed: 208 mm/sec total power requirement: 14 kW weight of the machine ca.: 8,5 t dimensions of the machine ca.: m Press force: 160 t Stroke: 400 mm Table size: 1,150 × 350 mm Cylinder diameter: 300 / 185 mm Throat depth: 225 mm Pressing speed: 6 – 16 mm/s Rapid approach speed: 75 mm/s Return speed: 208 mm/s Total power requirement: 14 kW Machine weight: approx. 8.5 t Pressing speed: 6 – 16 mm/s Rapid approach speed: 75 mm/s Return speed: 208 mm/s Installation distance between ram pressure pad and crosshead pressure pads: 320 mm Distance between pressure pads on ram and table: 50 – 888 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.