127,516 used machines on RESALE, but how to find them? Machine Search
Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor, motor contactor -Manufacturer: Siemens, contactor type 3TF2001-OBB4 -Number: 3x available -Price: per piece -Dimension: 50/45/H90 mm -Weight: 0.2 kg
Powder curing furnace 4,500 x 1,900 x 2,000 mm electric 1 Inner dimension length 4,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 5,700 = 11,400 m³/h 10 electric motors 2 pcs 2x 2.2 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 74 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device for exhaust air ...
OPTIdrill Bench Drill DQ 18 Spindle Holder MK 2 Motor 550 W, 230 V Drilling capacity up to 16 mm Keyless chuck Drilling table 200 x 200 mm, swivel and tilt 5 speeds 600 - 2400 rpm Weight approx. 30 kg 0041 62 922 68 28
Powder furnace el. or gas Powder curing furnace 6,500 x 1,900 x 2,000 mm 1 Inner dimension length 6,500 mm 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 7,500 = 15,000 m³/h 10 electric motors 2 pcs 2x 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 110 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device fo ...
Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor, motor contactor -Manufacturer: Siemens, contactor type 3TH2040-OBB4 -Number: 7x available -Price: per piece -Dimension: 50/45/H90 mm -Weight: 0.2 kg/pc.
Powder curing furnaces in various sizes, gas or electric 1 Inner dimension length 1500 - 6,500 [mm] 2 Inner dimensions width 1700 - 1,900 [mm] 3 Inner dimensions height 2,000 [mm] 4 Steel profile substructure 5 walls Galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling rock wool 150mm 75Kg/m² 7 Floor furnace gets 2 entry rails for tray trolleys (optionally with conveyor technology) 8 Temperature 220°C 9 fans 1 - 2 pcs. 2600 - 15,000 [m³/h] 10 electric motors 1 - 2 pcs 1.1 - 6 [kW] , 1450 [rpm], 3 F, 50 [Hz] 11 Thermal power 14 - 99 [kW] 12 hinged or sliding doors on one or both sides 2 - 4 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock Stainless Steel INOX AISI 316 Heating Electric or Gas Heat-Resistant Fans and Heat-Resistant Bearings, Thermoblock Has Overheating Protection
OKK VM5-II CNC machining center built in 2002 in Japan, is used for precision machining of workpieces. The machine features a large workspace, which includes among others a 30-position tool magazine and a reliable spindle, operating at a maximum speed of 8000 rpm. The design, made from high-quality raw materials, ensures exceptional rigidity and stability, even during the most intensive challenges. The OKK VM5-2 CNC vertical machining center weighs 6806 kg. Technical specifications of the OKK VM5-II CNC milling machine - CNC controller: FANUC Series 16i-M - feed in X/Y/Z axis: 1020/510/510 mm - work table dimensions (L x W): 1049 x 561 mm - maximum spindle rotational speed: 8000 rpm - 30-position tool magazine - tool holder: BT 40 - number of T-slots: 5 - installed power: 47 kVA - power supply: 3x 380 V; 50 Hz - dimensions (L x W x H): 3330 x 2830 x 3000 mm - weight of mach ...
Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor, motor contactor -Manufacturer: Siemens, contactor type 3TH2022-OBB4 -Number: 17x available -Price: per piece -Dimension: 50/45/H90 mm -Weight: 0.2 kg/pc.
Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor, motor contactor -Manufacturer: Siemens, contactor type 3TF2010-OBB4 -Number: 19x available -Price : piece -Dimension: 50/45/H90 mm -Weight: 0.2 kg/pc.
Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor, motor contactor -Manufacturer: Siemens, contactor type 3TH2040-OAMO -Number: 1x available -Price: per piece -Dimension: 50/45/H90 mm -Weight: 0.2 kg/pc.
Motor protection relay, relay, heating current monitoring, preheating for generators, contactor, semiconductor contactor, contactor, motor protection -Manufacturer: Siemens, motor protection type 3UN2100-OAB4 -Number: 4x available -Price per piece -Dimension: 95/20/H95 mm -Weight: 0.2 kg/pc.
tool taper: VDI shaft cross cut: 40 tool taper: Okuma ratio: ? turning speeds: ? U/min : ? coolant: ? Set of tool holders VDI 40 with drive ( 8 pieces ) suitable e.g. for OKUMA box dimensions approx. 500 x 300 x 200 mm weight approx. 50 kg 3 x EPPINGER 4.200.231 drilling and milling head 3 x EPPINGER 4.200.289 drilling/milling head 1 x Drill- Milling head WTO 4 1 06 1 6006 - 40 1 x COROMANT 410 1200 72 - 40 drilling and milling head 1 x 2-jaw chuck KH 1-40 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Control card, output card, controller, memory module, PLC controller, expansion module, interface module -Manufacturer: Siemens Simatic S5 Memory Subrmodule Eprom, 32K -Type: 6ES5373-OAA41 -Dimensions: 55/15/H95 mm -Weight: 0.1 kg
Control card, output card, controller, memory module, PLC controller, expansion module, interface module, Eprom -Manufacturer: Siemens Simatic S5 EPROM memory module ovp -Type: 6ES5376-OAA21 -Number: 1x module available -Cardboard dimensions: 60/55/H15 mm -Weight: 0.1 kg
Hydraulic unit, hydraulic pump, hydraulic pump, universal unit, gear pump, double hydraulic pump -Manufacturer: Orsta, double hydraulic pump -Pump 1: Type A 6.3 R -Pump 2: Type C 16-2 R -Motor: VEM KMR 112 M4 5.5 kW / 1440 rpm -Total dimensions: 725/250/H290 mm -Weight: 65 kg
Pressing force max KN 600 Withdrawal force max KN 300 Die Supporting force max KN 300 Die return force max KN 32 Upper punch travel mm 190 Upper punch adj.travel mm 200 Filling height max mm 180 Pressing travel max. mm 90 Withdraw travel max. mm 95 Top pressing travel max mm 18 Adjustment at Die position mm 50 Filler travel mm 140 Maximum forming Diameter mm 130 Cycle stroke /min 12-25 Main Motor Power KW 15 Total Power KW 15 Speed control method Inverter Driving pressure for Clutch MPa 0.55 Pre-load Travel mm 110 Total air consumption L/min 300 Total weight Kg 5800 Overall size H mm 3200 W mm 1750 D mm 1480
mechanically switchable clutch, releaseable clutch, power clutch, clutch -Manufacturer: Ortlinghaus, coupling type 100110405 35-12 -Translation: i= 1:1 -Shafts: Ø 24x60 / 24x55 mm -Dimensions: 405/212/H213 mm -Weight: 41 kg
mechanically switchable clutch, detachable clutch, power clutch, clutch -Manufacturer: Ortlinghaus, coupling without type designation -Translation: i= 1:1 -Shafts: Ø 24x60 / 24x55 mm -Dimensions: 310/212/H213 mm -Weight: 32 kg
Alignment tester, shaft aligner, laser shaft aligner -Manufacturer: db Prüftechnik, alignment tester Optalign 1.5 -Accessories: see photos -Dimensions transport box: 420/290/H555 mm -Weight: 20 kg
Oven, doors single-sided, electric Dimensions: 3,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 54 kW Auxiliary heating: electrically indirect via thermoblock
Oven, doors single-sided, gas Dimensions: 4,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Recirculating air: Q = 12000 m³/h P = 2 x 2.2 kW Heat output: 69 kW Auxiliary heating: Gas indirectly via thermoblock
Transmission, planetary gear for hydraulic motor, hydraulic motor, oil motor -Manufacturer: dinamic oil, gearbox type EH211 SN 6.2 -Dimensions: see photos -Total dimensions: Ø 230 x 190 mm -Weight: 30 kg
Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock
Used machine in good condition. Available for immediate delivery. - Control: SINUMERIK 880 T 3 - Max. length: 400 mm - Tool-holder cone: CONO ISO 50 - Tool magazine capacity: 16 #
Transmission, planetary gear for hydraulic motor, hydraulic motor, oil motor -Manufacturer: dinamic oil, gearbox type EH201 S 6.2 MO A16B -Dimensions: see photos -Total dimensions: Ø 230 x 178 mm -Weight: 29 kg
Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock
colour units: 1 max. printing speed sheets: 5500 /h max. paper size: 26 x 38 cm serial no.: 194.443 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Transmission, planetary gear for hydraulic motor, hydraulic motor, oil motor -Manufacturer: dinamic oil, gearbox type EH201 S 6.2 MO AS -Dimensions: see photos -Total dimensions: Ø 230 x 178 mm -Weight: 29 kg
Open Powder Spray Stand Dimensions: 2500 x 2250 x 2700 [mm] Extraction capacity: Q = 8000 m³/h P = 5.5 kW Filter: 1 stage: Filter cartridges 4 pieces à Ø 325 x 1000 [mm] 2nd stage: Pocket filter (absolute filter for fine dust) Note: The overspray during powdering is absorbed by the suction unit. The powder spray stand is delivered on rollers and is therefore mobile
Hydraulic pump, oil pump, gear pump, vane pump, hydraulic unit -Manufacturer: Brueninghaus, hydraulic pump type OVS 0 28 DFR/30 R-PPA 12 N 00 -Pump: Nominal pressure 250 bar -Drive: Behncke QU FA 00L4B-41 -Power: 3 kW 1442 rpm -Dimensions: 620/300/H270mm -Weight: 50kg
- Minimum roughness: 0.08 - 0.1 ?m Ra - Weight: 2.100 kg - Heavy duty generator: 100 A - Max. electrode weight: 50 kg - Max. workpiece weight: 750 kg - Work table size (width x length): 600 x 400 mm - Tank dimensions: 920 x 590 x 350 mm - Max. dis
used
OKS Stationary Air Pressure Vessel Galvanized 1 piece 2000 liters 1 piece 1000 liters Test pressure 16 bar, operating pressure max. 11 bar at call Tel. 01715213204
hydraulic motor, oil motor, hydraulic pump, hydraulic valve -Manufacturer: Danfoss, hydraulic motor with: valve block -Manufacturer hydraulic motor Danfoss type: OMP 315 151-0033 7 -Valve block: Hawe SK.7356-160/160 -Shaft: Ø 25 x 40 mm -Dimensions: 240/130/H200 mm -Weight: 9.8 kg
Bosch (SIG) / Jakob & Wienmeier / OCS / Seidenader / Pester blister packing line comprising of Kraus infeed conveyor for manualy feeding the blisters, Bosch (SIG) HSL horizontal flow pack machine with Koenig & Bauer alphaJET inkjet printer for printing the variable data onto the flow packs including camera print verification, Allen Bradley PLC, 2 (two) Jakob & Wienmeier horizontal cartoning machines type CK05-AV-6/R and CCM-AH-6-600-SV with blister buffer station type CCM-PZ, wolke m600 advanced inkjet printer for printing the variable data onto the cartons including camera print verification, Laetus bar code reader, feeder for booklets, etc., OCS type HC checkweigher (max. 750 g), Seidenader T&T Single Unit Track & Trace System for marking and verification of folding boxes/cartons for serialisation and aggregation with wolke m600 advanced inkjet printer, Pester PEWO-pack 250 compact str ...
Buchdrucktiegel - Stanztiegel / Letter Press Tiegel - DIE Cutter Heidelberg OHT Year 1966 - Serial-No. 155017 N Size min.: 40 x 70mm - max. 260 x 380mm Speed min.: 2.200 sph - max. 5.500 sph Standard chase: 260 x 340mm Skeleton chase: 260 x 350mm Komplett mit Zubehör und Schließrahmen / Complete with tools and accessories include frame Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
Bending tool, die, upper knife, upper tool, straight tool, upper beam -Bending tool: for folding machine -Tool angle: 45° -Dimensions: see the drawing in the photos -Dimension: 47 x 11mm -Length: 945mm -Weight: 3.5 kg
weight max. in kg: 10000 kg weight: 10 kg dimensions: 700 x 300 x 300 mm with power supply and remote control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Servo Motor, Electric Motor, DC Motor, Stepper Motor, Stepper Motor, Stepping Motor -Manufacturer: Oriental Motor, Vexta Stepping Motor stepper motor unused original packaging -Type PK268-02B -Shaft: Ø 6 x 18 mm -Dimensions cardboard: 140/80/H70 mm -Weight: 1.1 kg/pc.
Buchdrucktiegel - Stanztiegel / Letter Press Tiegel - DIE Cutter Heidelberg OHT Year 1962 - Serial-No. 137806 N Size min.: 40 x 70mm - max. 260 x 380mm Speed min.: 2.200 sph - max. 5.500 sph Standard chase: 260 x 340mm Skeleton chase: 260 x 350mm Komplett mit Zubehör und Schließrahmen / Complete with tools and accessories include frame Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
Flat pulley, toothed pulley, multi-belt pulley, timing belt pulley -Timing belt pulley: Ø 160 mm -Type: 34-14M-85 - Pitch: 14 mm / belt width approx. 85 mm -Receptacle: Taper clamping bushing optibelt 3525-40 Ø 40 x 65 mm -Dimensions: Ø 160 x 100 mm -Weight: 7.5 kg
I am selling a fully equipped edge banding machine BRANDT Optimat KDF 220 C, built in 2014: Configuration: Input stop manually adjustable Manually adjustable joint milling Edge banding EVA glue / PUR glue possible Material pressure zone manually adjustable Cross-cut saws pneumatically adjustable Radius milling at the top + bottom manually adjustable Round unit 1-motor manually adjustable Radius scraper R2 can be adjusted pneumatically (set R1 included) Control panel Working height adjustable by servo motor Material height 8-50mm Edge material thickness 0.4-3mm Feed speed 10m/min. Length including feed plate 4150mm Weight 1320kg Very good condition, fully functional ! Including full documentation and CE. Available the same.
Buchdeckenausbiegemaschine - Case Bender Orient CX Year 1993 - Serial- No. 9384/15344 Working width max. 500mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
Solid-state relays, switchgear, switching components -Manufacturer: opto 22, solid state relay 6 pieces with heat sink -Type: 480D45-12 -Quantity: 2x assembly available -Price: per assembly -Dimensions: 300/200/H70 mm -Weight: 3.4 kg/pc.
Semiconductor relays, switchgear, switching components -Manufacturer: opto 22 electromatic, Semiconductor relays, 7 pieces with heat sink -Type: 6x opto 22 480D45-12 / 1x electromatic RA4425-D08 -Price/Sale: complete -Dimensions: 300/200/H70 mm -Weight: 3.4 kg
Semiconductor relays, switchgear, switching components -Manufacturer: opto 22 electromatic, Semiconductor relays, 7 pieces with heat sink -Type: 5x opto 22 480D45-12 / 1x Gavazzi RA4450-D08 -Price/Sale: complete -Dimensions: 300/200/H70 mm -Weight: 3.4 kg
Hydraulic pump, oil pump, gear pump, hydraulic unit -Manufacturer: ORSTA, hydraulic pump with clutch bell -Pump Type: A25R -Clutch bell: IWK 8420523 -Shaft: Ø 22 x 25 mm Recess: Ø 250 mm -Hole circle: Ø 300 x 18 mm -Dimensions: 285/285/H245 mm -Weight: 7.1kg
Buchdrucktiegel - Stanztiegel / Letter Press Tiegel - DIE Cutter Heidelberg OHT Year 1974 - Serial-No. 186 403 N Size min.: 40 x 70mm - max. 260 x 380mm Speed min.: 2.200 sph - max. 5.500 sph Standard chase: 260 x 340mm Skeleton chase: 260 x 350mm Komplett mit Zubehör und Schließrahmen / Complete with tools and accessories include frame Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
Forklift battery charger, industrial charger, forklift battery charger, industrial charger, Si rectifier -Manufacturer: Oldham, charger type High Power III 36-80 -Input voltage: 220/380V 50Hz -Power: 36 V / 80 A -Dimensions: 555/410/H790 mm -Weight: 66 kg
Servo motor, electric motor, DC motor, stepper motor, stepper motor, stepping motor -Manufacturer: Oriental Motor, Vexta Stepping Motor stepper motor -Type C7219-9012K -Shaft: Ø 5 x 18 mm -Dimension: 67/42/H42 mm -Weight: 0.3 kg
Buchdrucktiegel - Stanztiegel / Letter Press Tiegel - DIE Cutter Heidelberg OHT Year 1964 - Serial-No. 149218 N Size min.: 40 x 70mm - max. 260 x 380mm Speed min.: 2.200 sph - max. 5.500 sph Standard chase: 260 x 340mm Skeleton chase: 260 x 350mm Komplett mit Zubehör und Schließrahmen / Complete with tools and accessories include frame Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
maximum number of results exceeded
please refine your search
