129,235 used machines on RESALE, but how to find them? Machine Search
Feed screw stainless steel used Manufacturer: KOMEN & KUIN D.V. Diameter approx. 500 mm, Conveying length approx. Mm Stainless steel Drive 3 kW 380 / 420 V Total dimensions approx. 4 x 1.6 x 1.6 m. The screw was mounted on this screw blancher Changes and errors in the technical data and information excepted.
Key data: 250 , 4 , 45
Electr. Power: 250 KW Motor speed:1492 rpm Voltage: 400 V Weight: 5630 kg The compressors have been taken over in operational condition and are complete.
Tip height: 250 mm Center width: 1500 mm Circulation Ø: over bed 500 mm Spindle bore: 63 mm Spindle holder: Size 8 Mounting cone tailstock: 5 MK Spindle speeds: 170 - 2240 rpm Feeds: longitudinal/flat 0.014-1/0.0063-0.45 mm/U Thread pitches: 0.1 - 112 mm electrical connection: 380 V, 7.5 kW Space requirement: 2300 x 1000 x 1400 mm Weight: 2360 kg
Oil lubricated screw compressor Cooling: Air-cooled design Drive: High-frequency motor with 1:1 direct drive Control: Speed-controlled with frequency converter Control: Aircontrol 5.0 (4-20mA) Refrigeration dryer: Integrated, refrigerant R134a Filtration: incl. cyclone separator Performance data Volume flow at operating pressure 7.0 bar 0.27-1.86 m³/min Volume flow at operating pressure 10.0 bar 0.37-1.50 m³/min Operating pressure min. / max. 5.0 / 12.5 bar Total power consumption at 10.0 bar / full load 13.3 kW Rated power motor; IP55 11.0 kW Oil volume 4.7 lt Pressure dew point refrigerant dryer ( 20°C 100% RH) +3 °C Installation data Ambient conditions min. / max. 1 / 46 °C ∆ T above cooling medium temperature 4 °C Cooling air requirement 2200 m³/h Free fan pressure 30 Pa Sound level 63 dB(A) Voltage / Frequency 400 / 50 V / Hz Refrigeration dr ...
Ground precision ball screw, D50 mm, 1143 mm, Steinmeyer, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type 3526.508/30.50.900.1143 E T3, D50 mm, 1143 mm, Z-Nr. 3-30-900-0-3-01, Fa. Steinmeyer Ball screw diameter 50 mm, Pitch 30 mm, Length of thread 900 mm Length of ball screw nut 209 mm, Max. total stroke 691 mm, Total length of the spindle 1143 mm Diameter for coupling with motor 38 mm Attention! With 2 mounted roller bearings! Outer diameter bearing A 80 mm, outer diameter bearing B 52 mm Functional guarantee! We cannot pr ...
Ground precision ball screw, D40x20, 1600mm, Rexroth, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type 1586-4-7212, D40 x 20/25, 1600 mm, Fa. Rexroth, Ball screw diameter 40 mm, Pitch 20 mm, Length of thread 1415 mm Length of ball screw nut 87 mm, Max. total stroke 1328 mm, Total length of the spindle 1600 mm Diameter for coupling with motor 24 mm Diameter bearing seat A 30 mm, Diameter bearing seat B 28 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we give y ...
Ground precision ball screw, 80270, D50mm, 1300mm, Honsberg, new As good as new in original packaging! The high-quality part comes from a spare parts warehouse of a mechanical processing of a large automobile manufacturer, is completely new and in the original packaging. Attention: We have many, bearing, high-quality ball screws in different designs in diameters 32, 40, 50, 63 and 83mm. Take a look at our website of IPV GmbH. ball screw, ball screw, ball roller spindle, Type 80270, D50 mm, 1300 mm, Fa. Honsberg, ball screw diameter 50 mm, pitch 10 mm, Thread length 1080 mm length of ball screw nut 142 mm, total stroke 938 mm, Total length of the spindle 1300 mm Diameter for coupling with motor 30 mm Diameter bearing seat A 35 mm, diameter bearing seat B 35 mm Functional guarantee! For second-hand parts, we cannot provide a conventional guarantee and warranty. Howe ...
Ball screw with motor bell, bearing and coupling, D50x680mm, , mint condition Special price ! High quality parts from a major car manufacturer! If you have a VAT number we will gladly issue an invoice without VA. As good as new! The assembled linear actuator comes from a spare parts store of a mechanical processing was there for a long time in stock, is preserved and has never been used. Technical data: 1 pc ball screw with motor bell, bearing and clamping set for mounting on the drive motor consisting of: - 1 pc. motor bell with bearing for the ball screw drive and 1 clamping set for mounting on the drive motor, Fa. Grob - 1 pcs. ball screw drive MVD400-155-100-2, total length of the spindle approx. 560mm, thread length 355mm, pitch 10mm, Max. Total stroke 193mm, - 1 pcs. nut to ball screw, length of nut 162mm, Function guarantee! For second hand parts, we can ...
Key data: 7 , 10 , 1
Oil lubricated screw compressor Cooling: Air-cooled design Drive: Efficient IE3 motor with belt drive Control: fixed speed Control: Airlogic² T touchscreen full-color display Refrigeration Dryer: Integrated Performance data Volume flow at operating pressure 9.5 bar 1.15 m³/min Operating pressure min. / max. 5.5 / 10 bar Total power consumption at 9.5 bar / full load 10.0 kW Rated power motor; IP55 7.5 kW Oil quantity 3.7 lt Installation data Ambient conditions min. / max. 1 / 46 °C Cooling air demand 1188 m³/h Free fan pressure 30 Pa Sound level 65 dB(A) Voltage / PH / Frequency 400 / 3 / 50 V / Ph / Hz Dimensions and weight Length x width x height 1625 x 665 x 1535 mm Weight 355 kg Compressed air outlet G 3/4 "ig Capacity compressed air tank 270 lt
Schatz Advanced screwdriving system Schatz screwdriving system Length: 5450 mm Height: 3000 mm Roll-off block Length 5020 mm 2 x Demag crane 1 x Liftket electric chain hoist 1 x Treasure 907500 System without Advantech TPC-1260 TE Touch Panel PC Item location: 42859 Remscheid Disassembly and transport by the buyer. The disassembly, loading, as well as transport can alternatively be offered by us. Find more screwdriving systems in other sizes - new and used -
Figure shows MIOTAL® TC 180 x 1000 Center width: 750 mm Center height: 165 mm Orbit diameter over bed: Ø 330 mm Bed width: 190 mm Travel cross slide: 160 mm Travel upper carriage: 90 mm Spindle connection: DIN 55029 (Camlock) D 1 - 4 Spindle bore: Ø 40 mm chuck diameter: Ø 200 mm Spindle speed, infinitely variable: 30 - 2000 rpm Mechanical counters: 3 Motor power: 2.2 kW Longitudinal feeds Z: (40) 0.044 - 1.96 mm/rev Feed rates X: (40) 0.022 - 0.98 mm/rev Thread Metric: (32) 0.4 - 7.0 mm Thread inch: (32) 4 - 56 gg/inch Thread module: (32) 0.4 - 7,0 Diametrical thread: (32) 7.5 - 112 Quill diameter tailstock: Ø 40 mm Inner cone of the quill tailstock: MK 3 Quill stroke: 100 mm Lateral adjustment: ± 10 mm Weight, approx.: 650 kg Characteristics: - Acceptance protocol according to DIN - Precise, hardened and ground guides - Robust headstock with circula ...
Center height: 205 mm Orbit diameter over bed: 410 mm Center width: 1000 mm Bed width: 260 mm Spindle nose: DIN 55029 (Camlock) 9, size 6 Travel cross slide: 220 mm Travel upper slide: 125 mm Spindle bore: 52.5 mm Spindle speeds: 20 - 3000 min-1 Speed control: Infinitely variable Mechanical counters: 2 Motor power: 3.75 kW Coolant pump: 0.13 kW Longitudinal feeds Z: 0.05 - 1.7 mm/rev Face feeds X: 0.025 - 0.85 mm/rev Whitworth Thread: (45) 2 - 72 TPI Metric threads: (39) 0.2 - 14.0 mm Diametric thread: (21) 8 - 44 DP Module thread: (18) 0.3 - 3.5 MP Quill diameter: 52 mm Inner cone quilt: MK 4 Quill stroke: 150 mm Dimensions: 2270 x 1120 x 1900 mm Weight, approx.: 1500 kg Characteristics: - Tool mesh accuracy according to DIN 8605 - Infinitely variable speed control (2 countershafts) - Finely balanced main spindle - Stable machine bed with hardened and gro ...
Center width: 1000 mm Center height: 178 mm Orbit diameter over bed: Ø 356 mm Bed width: 190 mm Travel cross slide: 160 mm Travel upper carriage: 90 mm Spindle connection: DIN 55029 (Camlock) D 1 - 4 Spindle bore: Ø 40 mm chuck diameter: Ø 200 mm Spindle speed, infinitely variable: 30 - 2000 rpm Mechanical counters: 3 Motor power: 2.2 kW Longitudinal feeds Z: (40) 0.044 - 1.96 mm/rev Feed rates X: (40) 0.022 - 0.98 mm/rev Thread Metric: (32) 0.4 - 7.0 mm Thread inch: (32) 4 - 56 gg/inch Thread module: (32) 0.4 - 7,0 Diametrical thread: (32) 7.5 - 112 Quill diameter tailstock: Ø 40 mm Inner cone of the quill tailstock: MK 3 Quill stroke: 100 mm Lateral adjustment: ± 10 mm Weight, approx.: 750 kg Characteristics: - Acceptance protocol according to DIN - Precise, hardened and ground guides - Robust headstock with circulating oil lubrication, precision-be ...
various screws up to diameter 150 mm available
Key data: 130
Extruder 1 spindle : 130 mm Ø, 35 L / D, for grancear plastics, brand: Plasco, with forced feeding. Degasser, with vacuum pump: 15 hp. Filter changer: 260 mm, overhead cut to water. Vibrating screen and motor: 238 KW with variable speed drive and electrical panel. GT-2982
Stock No. 2590k 1 used compounding pelletizing line, throughput up to 1200 kg/h depending on material, consisting of: 1x Grav. Dosing system 5-component SITECOM incl. control 1x Extruder twin screw THEYSOHN type TSK 90 Screws 2x Ø 90 mm – 36 LD synchronization Segment screw and barrel, water / medium cooled Screw speed up to 300 rpm-1 Extruder drive 255 kW-DC 1x side dosing extruder TSD 75 twin screw with drive 3 kW 3x degassing openings 1x melt filter No. 1 type K –HS- Y with sieve 176 mm, incl hydraulic 1x melt pump with drive 22 kW 1x meelt filter No.2 type K-SWE 180 RS back-flush self-cleaning incl. hydraulic 1x strand head with 32 x Ø3.5 mm holes 1x strand cooling pool 620 x 5000 mm 1x string granulator SG 300, drive 11 kW Screen control ResoTec / control cabinet Visit / demonstration at short notice by arrangement. Further compounding lines and access ...
Key data: 120
Extruder 1 spindle for manufacture of pellets. 120 mm Ø, 35 L/D, brand name: FBM ( Falzoni), type: ETF 120 V 380/5L, year: 1988. Engine: 200 KW. Degasifier and filter changer. Head cut under water, year: 2006, brand: PRT and force-feeding silo.
Key data: 50
Extruder 2 spindles: 50 mm Ø 12 L/D, motor: 4.5 kw, without electrical panel.
Key data: 50
Extruder 2 corrotating spindles: 50 mm Ø, 40 L/D, brand: ICMA SAN Giorgio, with double degasser. Motor: 57.5 Kw direct current with drive. Material dispenser and thread head (spaghetti), with electrical panel.
Extruder 2 spindles 18L/D, model: BK-50-93, tapered spindles, brand: Volcano, with motor: 25hp, with variable speed drive. Degasser and dispenser of material and electrical panel.
Key data: 120
Extruder 1 spindle : 120 mm Ø 35 L/D, make: Union, motor: 110 Kw (150 hp). 4.2 m. long. With degasser, filter changer: 220 mm, overhead cutting to the water with centrifuge and screen. Electrical panel with variable speed drive.
Key data: 60
Extruder 1 spindle: 60 mm Ø 32 L/D, Amut brand, variable speed motor Elektra Faurndau: 7 to 24 KW, with electrical panel and wire head for pellets: 23 holes and electrical panel.
Equipped with 3 outlets with pneumatic valve, approximately Ø200mm Auction-ID: A1-43573-101
Key data: 90
Extruder 1 spindle Brand: Eurotecno, 90 mm Ø, 33 L/D. Electrical panel, filter changer: 160 mm, wire head for graining, stainless bathtub: 3 m, without motor. Eurotecno noodle model G-400 with blades: 300 mm.
Key data: 120
Extruder 1 spindle: 120 mm Ø, 35L/D, brand: Union, with degasser, hydraulic filter changer: 150. Year: 1987.
Key data: 65
Extruder 2 corrotating spindles: 65 mm Ø, 30L/D, brand: Maris, model: TM-65 V. Shirt and spindle compatible by segments. Degasser, motor: 90 KW DC, with variable speed. Thread head and 2 spare spindles.
Key data: 60
Extruder 1 spindle: 60 mm Ø, 25 L/D, brand: Safinio, motor: 20 hp, variable speed drive, brand: Omron, model: F7, alternating current: 30 kw and electrical panel.
Center height: 315 mm Center width: 1000 mm Circulating Ø: 630 mm Spindle bore: 74 mm Spindle holder: Size 8 Pick-up cone tailstock: 5 MK Spindle speeds: 7 - 710 rpm Feeds: longitudinal/flat 0.063-4/0.030-2 mm/rev Thread pitches: 1 - 14 mm electrical connection: 380 V kW Space requirement: 2750 x 1250 x 1380 mm Weight: approx. 4200 kg
pneumatic angle grinder, flex, grinding witch, cut-off grinder, cut-off machine, angle grinder -pneumatic straight screwdriver -Operating pressure: 6 bar -Speed: 900 rpm -Price: per piece -Number: 2 pieces -Dimensions: 380/42/H67 mm -Weight: 1.4 kg/piece
Ball screw with nut, transroll spindle, ball screw nut, threaded spindle, threaded rod, threaded bolt, threaded rod -Manufacturer: NTN -Thread: diameter 32 mm -Pitch: approx. 10 mm -Thread length: 482 mm -Techn. Drawing: see photos -Dimensions: 672/93/H93 mm -Weight: 9 kg
maximum number of results exceeded
please refine your search
500 € 
