We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
119,279 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
For sale complete plant for wood pellet production, made from CPM, capacity 6t/h. A most of the maschines from line are produced in between 2008-2010.y., except presses for making pellets (its bit older then rest of the line, but completly renewed before restarting. Line is consisting from: 1.Chain conveyer for logs transport. 2.Lift with angle platform for dosing material. 3.Entrance belt transporter with magnetic section for detection of iron. 4.Grinder (hammer mill) BRUKS 500kW 5.Verticaly basket transporter for chip wood. 6.Horisontal belt transporter for chip wood with three side ejectors into depoos (separated with type of the wood) 7.Hidraulic floor platform for dosing wood chips (three pcs.) with all instalation and system of hidraulic pistons. 8.Horisontal belt transporter for transportation material on drying. 9.Repler transporter for driving wood chips into fire plac ...
new
L 45 Kw POWER 680 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw
new
L 30 Kw POWER 450 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 30 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw
used
SINO NCP 160 eccentric press built in China in 2018 by Sino Machinery & Tools (Dongguan) Co., LTD. performs machining of metal workpieces with a press force of 160 tonnes. The machine is equipped with high-quality components, including e.g. a 100 mm adjustable slider making up to 25 to 55 strokes per minute, and a YU JAIV PDH-120 indicator displaying the distance of the die between the table and the slider. The large working area, ease of operation and outstanding precision, guarantee excellent machining results. The press offers the possibility of combining it with an automatic feeding system in order to increase the number of parts produced and significantly reduce costs. The total weight of the machine is 13 tonnes. Technical data of the SINO NCP 160 press - maximum press force: 160 t - work area dimensions (L x W x H): 910 x 600 x 410 mm - bolster dimensions (L x W x H): 125 ...
new
FRICTION BELT DIRECT FROM THE MANUFACTURER! Description: -Chrome leather friction belt for screw press, riveted, new! -Dimensions: 530 mm i.diameter x 50 mm high x 18 mm thick ON request make we the friction belts regarding to your sizes! For all machine types like SMS Hasenclever Berrenberg, Schuler, Weingarten, Vaccari, via, Mecolpress, Osterwalder... We deliver worldwide!
used
Frame press Maweg Size: 400 x 240 cm hydraulic 3 vertical cylinders 2 horizontal cylinder Built in 1984 Weight approx. 2500 kg L x W x H: 480 x 110 x 270 cm The machine is in good condition, ready to use. Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
new
AYEL-TECH WORKSHOP PRESS TYPE WP 100 -Capaciteit 100 ton -Cilinderslag 400 mm -Werkbreedte 1000 mm -Verplaatsbaar cilinder is -Electric of hand-mat bedienbaar -Pressure gauge -Noodstop -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
new
AYEL-TECH WORKSHOP PRESS TYPE WP 60 -Capaciteit 60 ton -Cilinderslag 400 mm -Werkbreedte 1000 mm -Verplaatsbaar cilinder is -Electric of hand-mat bedienbaar -Pressure gauge -Noodstop -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
used
Slot boring machine Scheer L x W x H: 70 x 60 x 140 cm Weight approx. 400 kg Built in 1975 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
used
Glue press Etienne Format L x B: 3800 x 2700 mm Window frame press pneumatic Weight approx. 890 kg Year of construction 1980 The press is in good condition, ready to use. Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
used
Manufacturer: SCHULER Model: ES2 400 T Year of manufacture: 1984 Condition: Very good Location: Rudniki - Poland Press Capacity: 400 Tons Rated Tonnage Point 12.5 mm The Height: 1018 mm Slide Adjustment: 305 mm Slide Stroke: 610 mm Bolster Size: 2743 x 1524 mm Slide Size: 2743 x 1524 mm SPM: 20 The Cushion Capacity: 70 tons x 2 pcs. The Cushion Stroke: 203 mm Main Motor Capacity: 60 KW Moving Bolster: Front Exit
new
AYEL-TECH WORKSHOP PRESS TYPE 30 WPM -Capaciteit 30 ton -Werkbreedte 600 mm -Hand mat-bedienbaar -Pressure gauge PRICE IS plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
used
HOT PRESS type COLOMBO REMO HPC 8 / 160 second hand WITH SOLID STEEL PLATES Heavy-duty construction Hot water heating via a electric system on the back of the machine , not any connection needed , everything is included on the machine Total Kw for heating 25 Solid steel plates size mm. 3450 x 1400 n.08 pistons diam.mm. 90 max. thrust Ton. 160 specific pressure max. kgs.5 / cm2 opening mm. 660 emergency perimeter rope overall dimensions cm. 4500 x 2000 x 2700 H weight kgs. 8500
used
AYEL-TECH WORKSHOP PRESS TYPE WP 30 -Capaciteit 30 ton -Werkbreedte 700 mm -Electric of hand-mat bedienbaar -Pressure gauge -Noodstop -400V PRICE IS plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS
used
MEMBRANE PRESS type FISMA 2200 x 1300 . usata useful size mm. 2200 x 1300 cover opening and closer by pneumatic pistons volt. 380/50 with separate vacuum system
Force of pressure: 100 t projection: 350 mm table size: 690 x 840 mm Durchfalloch in the table: 160 mm table adjustment: slide area: 450 x 600 mm slide adjustment: 80 mm stroke adjustment: 8-100 mm stroke rate: 60 / min drive motor: 380 V, 5.5 kW space: 1850 x 1850 x 2650 mm weight: 6800 kg
used
With the universal hand punch NPR-20 can both on the front page as also Center of the punch be punched, so may here A4 sheet at any point are processed. The punch is suitable for cutting of printed materials in the Office, in the printer or in the copy shop. With a Nutmesser can A4 sheets are grooved. The NPR-20 is suitable for all cutting work, which can be with the NPR-10 through out. A countertop if necessary Additionally facilitates the stamping work
new
A roll punching press for stamping is available up to A3. The die is pulled under the roll.
used
robuse two-hand operation with heavy adjustable stand Overall width approx 420 mm Overall height approx. 870-1120 mm Weight approx. 35 kg
used
With the universal hole punch NPR-20 can both on the front page as also Center of the punch be punched, so may here A4 sheet at any point are processed. The punch is suitable for cutting of printed materials in the Office, in the printer or in the copy shop. With a Nutmesser can A4 sheets are grooved. The NPR-20 is suitable for all cutting work, which can be with the NPR-10 through out. A countertop if necessary Additionally facilitates the stamping work.
new
AYEL-TECH WORKSHOP PRESS TYPE WP 15 -Capaciteit 15 ton -Cilinderslag 260 mm -Werkbreedte 500 mm -Electric of hand-mat bedienbaar -Pressure gauge -Noodstop -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
used
Plywood Press, manufactured by Siempelkamp, working sizes 2500 x 1300, 10 floors
new
SAY MAK WORKSHOP PRESS TYPE WP 100 -Capaciteit 150 ton -Cilinderslag 400 mm -Werkbreedte 1100 mm -Verplaatsbaar cilinder is -Pressure gauge -Met V-Blokken -Noodstop -Documentatie -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
new
SAY MAK WORKSHOP PRESS TYPE SHP 100 -Capaciteit 100 ton -Cilinderslag 400 mm -Werkbreedte 1000 mm -Verplaatsbaar cilinder is -Pressure gauge -Met V-Blokken -Noodstop -Documentatie -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
new
SAY MAK WORKSHOP PRESS TYPE SRHP 250 -Capaciteit 250 ton -Cilinderslag 400 mm -Werkbreedte 1200 x 1000 mm -Slaginstelling -Pressure gauge -Noodstop -Weight 3450 kg -Power 11 kVA -Documentatie -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
new
AYEL-TECH PRESS BRAKE/WORKSHOP PRESS KBWP type 1050 x 100 ton -Capaciteit 1050 x 100 ton -Max Queen 1050 mm -Geeredschap -Pressure gauge -Noodstop -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
used
Baler Presto CC 20 M, year of construction 2016, pressing force 20 t Specifications: Manufacturer: Presto Type: CC 20 M Year of construction: 2016 Pressing force: 20 t Cycle time: 24 s Drive power: 7.5 kW Filling opening: 1030 x 750 mm Binding: 3-fold Throughput at bulk density of 35 kg/m³ - 1.6 t 60 kg/m³ - 2,3 t 100 kg/m³ - 2,8 t Bale dimensions: 700 x 750 mm Bale weight: up to 300 kg Dimensions: 3300 x 1235 x 1860 mm (LxWxH) Machine weight: ca. 2500 kg Please note: All technical data refer to information provided by the manufacturer. We assume no liability for the information provided or for any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale against advance payment takes place ex works, without guarantee and guarantee.
used
Briquetting press MATEC F-Cube 20 new Dimension press LxWxH: 130x74x112 cm weight 233 kg Briquette square 30x30 mm Capacity approx. 10-25 kg briquettes / hour Size feed funnel approx. 0.33 m3 Motor hydraulic pump 2.2 kW, 3x 400 V, 50 Hz Electricity consumption approx. 1.1 kWh How we work Continuous operation Year of construction 2021 Additional options: - Extension line for briquettes with stand -Auto. Start-stop system for operation with level monitoring - Sensors for level monitoring - Hydraulic oil 30 liters - 3 m cable with Euro plug 16 A - Flange adjustment filter-hopper press The spec. Density of briquettes is about 900 kg / m3. The maximum wood moisture content is 15%. The measured noise level is 62 dB. New machine, ready for operation. Subject to change, error, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden ...
used
1 PAAL horizontal tunel press type PAC, year 1997, tunel section 60 x 70 cm, bale measuring, tying through 4 horizontal wire insertion, machine was used for pressing textile waste dust, with dust suplying cyclone, by removing dust cyclone it can be used for pressing any material
used
Order No. 6761 TECHNICAL DATA 6 hydraulic cylinders: - 4 upper - 2 side - max. length of glued elements 3100mm - max height of glued elements 1600mm - pump motor power 1.5kW - dimensions length / width / height 4320x1500x1120mm - weight kg ADVANTAGES - unpainted - possibility of gluing in vertical and horizontal position - used press - very good condition PRODUCT FEATURES The press is designed for assembly of all rectangular frame structures, e.g. doors, windows of various dimensions. An additional hydraulic cylinder is responsible for the possibility of gluing in the vertical and horizontal position. Net price: PLN 18 900 Net price: EUR 4021 Net price, calculated at the rate of 4.70 PLN / EUR (with greater fluctuations in the rate, the price may change)
new
l 90 kw POWER 1350 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 500 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control of the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 90 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw
new
Dear customers, currently we offer a polystyrene press incl. shredder for sale. It is a new machine that has 0 operating hours! Here are a few more technical details: Material to be processed: EPS moulded parts and chips Maximum material density that can be processed: 18 kg/m³ Loading opening: 700 x 360 mm Filling height 1,402 mm Achievable compaction: up to 250 Kg/m³ System throughput: up to 15 kg/h Block dimensions: 130 x 130 mm Power supply: 3x400 VAC+N+PE 50 Hz Connected load: 1.5 KW, 400V 50Hz incl. automatic press pressure regulation with pellet holder Finish: RAL 7035 (light grey) combined with RAL 2011 (deep orange) Incl. water dosing system for direct screw cooling up to 10 litres/h with water shut-off valve. Price plus VAT, which will be shown separately on the invoice. Transport possible worldwide for an extra charge! If you have any questions, please d ...
new
Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...
used
capacity 6 000 kg/h power: elevator 2,2 (3,0) kW (PS) mill 5,5 (7,5) kW (PS) electric outlet 400V 50Hz (3 phases) fuse 16 A dimensions: length 1 800 mm width 900 mm height 2 450 / 2 700 mm insertion resp. discharge height 800 mm weight 420 / 450 kg material 1.4301 / AISI 304 connections: connection for cleaning ½ \" inside connection for washing bath 2 \" outside mash discharge height 1 480 mm suitable for pomaceous fruit scope of delivery 7, 9 and 12 mm cutting screen ; new machine - top condition
new
Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...
used
Wash waw LC40 with raetzmuehle RM40 for belt presses EBP500, EBP650 and EBP820 nominal power up to 2000 kg/h engine power 6.2 (8.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical protection 16 A 000 mm width 700 mm Hehe 2400 mm He he Assumption 800 mm Weight 285 kg Material 1.4301 / AISI 304 Connection for cleaning 1/2 inner Connection for washingHeight mash release 1500 mm Height fruit delivery 800 mm 9mm and 12mm Cutting sieve ; New machine - best condition
new
l 45 kw POWER 680 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw
used
Catalog No. 6853 TECHNICAL DATA - hydraulic clamping force - round briquette form - briquette diameter 65mm - dimensions of the tank height / width 770x940mm - sensor of the minimum level of trout in the hopper - automatic or manual operation of the machine - inspection window in the machine chute - pump motor 7.5 kW - agitator motor 0.35 kW - 2 types of screw speed 1100, 1700 rpm - screw motor 0.75 kW - dimensions length/width/height 2050x1650x1640mm - weight 895 kg ADVANTAGES – unpainted – German production – used briquetting machine - very good condition Net price: PLN 31900 Net price: 6860 EUR Net price calculated according to the exchange rate of 4.65 PLN/EUR (with larger exchange rate fluctuations, the price may change)
used
Catalog No. 6853 TECHNICAL DATA - hydraulic clamping force - round briquette form - briquette diameter 65mm - dimensions of the tank height / width 770x940mm - sensor of the minimum level of trout in the hopper - automatic or manual operation of the machine - inspection window in the machine chute - pump motor 7.5 kW - agitator motor 0.35 kW - 2 types of screw speed 1100, 1700 rpm - screw motor 0.75 kW - dimensions length/width/height 2050x1650x1640mm - weight 895 kg ADVANTAGES – unpainted – German production – used briquetting machine - very good condition Net price: PLN 31900 Net price: 6860 EUR Net price calculated according to the exchange rate of 4.65 PLN/EUR (with larger exchange rate fluctuations, the price may change)
used
automatic baler Manufacturer: UNOTECH Type: UPAMAT 100V 5 Year of construction: 2014 specifications: Cutting force: 1,000 / 315 KN / bar Specific pressing pressure: 12.12 kg/cm² Filling opening 2,000 x 1,020 mm Channel format: 750 x 1,100 mm (H x W) Bale weight: 500 - 800 kg (depending on material and bale length) Binding: 5-fold vertical Drive power: 1 x 75 kW Rated current consumption: 175 A Connection fuse max. 200 A Pump: Internal gear pump Noise emission: 82 - 85 dB/A Machine weight: 32.000 kg Control: Siemens S7 - IM-151 Capacity: approx. 340 m²/hour under operating conditions Throughput: at 30 kg/m³ bulk density approx. 10.0 t/h at 50 kg/m³ bulk density approx. 16.0 t/h at 100 kg/m³ bulk density approx. 32.0 t/h Equipped with: Press box planked with HARDOX central lubrication point Large digit displ ...
new
CNC – controlled frame gluing press for automatic gluing of all frame constructions with dowel connection – tine connection – 45° miter connection, automatic centering of the press plates and the upper press beam. The frame presses are available in the following sizes – pressing area 3,000 x 1,700 mm – 3,000 x 2,000 mm and 3,500 x 2,500 mm. Two vertical press cylinders – pressing force per cylinder 7 tons (optional four vertical press cylinders). Two horizontal press cylinders, stroke range 150 mm - pressing force per cylinder 3 tons. Maximum tread depth 130 mm (larger tread depths on request). CNC control from SIEMENS® with touch screen for calling up three automatic pressing cycles, 99 compression programs can be stored per pressing cycle. Among other things, the following parameters can be programmed: frame size, frame profile structure, pressing time, pr ...
new
Gluing stand VHS with motor hydraulics for gluing all frame constructions with dowel connection – tine connection – 45° miter connection. The motor-hydraulic gluing stands VHS are available in the following sizes: Maximum grouting range 2,500 x 1,800 mm 2,500 x 2,100 mm 3,000 x 1,800 mm 3,000 x 2,100 mm 3,500 x 2,100 mm Three vertical press cylinders with a stroke range of 120 mm and a pressing force of 2 tons each. Two horizontal press cylinders with a stroke range of 120 mm and a pressing force of 2 tons each (optionally, the gluing stands can of course be supplied with more press cylinders). Drive power 0.75 to 1.25 kW.
used
Pneumatic multi function press Operating pressure 6-8 bar Weight 106 kg dimensions 0.70 x 0.38 x 1.05 m Comments: Multi function punch air consumption 18 l per stroke, pneumatic punching operation via foot switch tripping
new
Total height 1500 mm Total length 3000 mm 5 pneumatic cylinders Compressed air pressure 8 bar Travel of pneumatic cylinders 100 mm Diameter of pneumatic cylinders 100 mm
used
A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Used Hosokawa Alpine APC K 200-50 pharmapactor with Flake Crusher AFC 300. The compactor allows to transform powder materials into briquets or granulates. Thanks to the extended range of accessories, such as different rollers and sieves, it´s possible to fully customize the form, size and shape of the end product adapting it to the required specifications. Specially built for pha ...
used
A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Refurbished Pharmapaktor APC L200/50. The Hosokawa Alpine APC L200/50 Pharmapaktor is the perfect compactor to test the product behaviour with this technology, while it even allows to keep a continuous production at small scale if needed. The Pharmapaktor can be fitted with a flake crusher to granulate the resulting compacted material increasing the possibilities of end produc ...
used
Pressure: 65 tons -Stroke: 140 mm -Table size: 720 x 600 mm -Plunger surface: 500 x 300 mm -Tappet adjustment: 80 mm -Strokes: 20-40 per min. -. Weight: 6000 kg -Dimensions (L x W x H): height 3.1 m -Clamping hole ø 60 x 80 mm More info on request
used
STANDARD-EQUIPPED
used
ZTS KOSICE LEK 160 eccentric press was built in 1985 in Czechoslovakia. The press, operating with a force of 160 tonnes and a slider making up to 50 strokes per minute, is designed for, e.g. punching, cutting and pressing of workpieces. Machining is performed on a large work table with a length of 1000 mm and a width of 740 mm, with full illumination in the form of a lamp mounted on the body of the KOSICE LEK 160 machine. The total weight of the machine is 12180 kg. Technical data of the ZTS KOSICE LEK 160 press - maximum press force: 160 t (1600 kN) - work space dimensions (L x W): 1000 x 740 mm - maximum number of slider strokes: 50/min - number of slider strokes in single mode: 32/min - maximum slider stroke: 160 mm - minimum slider stroke: 25 mm - slider adjustment range: 100 mm - reach: 355 mm - workspace illumination - weight of the KOSICE LEK-160 machine: 12180 kg
used
Tech. Data Nominal press force 1000 kN at maximum stroke adjustment - commute 6.5 mm 1250 kN at maximum stroke adjustment - commute 3.5 mm Strokes with endurance 125/83/63 Hube/min Usable stroke rate 50 50 38 / min. Throat depth 320 mm, clamp 380 mm Stroke adjustment 10-120 mm, Stosselverstellung 80 mm Stosselflaeche 800 x 320 mm, recording journal 50 / 85 Tabletop table top hole, 900 x 630 mm 230 mm, Durchfalloch in the table 300 / 400 x 250 mm Drive - 7,5 / 5,5 kW Bulk 1350 x 2080 x 2780 mm, Btto 8900 kg