screw presse used for sale

Lead and pull spindle lathe WEIPERT Year of Make: 1956 Spindle bore: 90 mm Center width: 3000 mm Circulation Ø over bed : 800 mm Circulation 0 over slide: 610 mm Circulation 0 in offset: 1120 mm Speed range: 7.5 – 475 rpm With the following accessories: Multifix tool holder with 11 inserts Coolant Setup Three-jaw chuck 0315 mm Three-jaw chuck 0 400 mm Three-jaw chuck 0 500 mm Face Plate 0 400 mm Face Plate 0 800 mm Face Plate 0 1000 mm Running Lynette Various turning tools (30 pcs. indexable insert tools) 2 moving centering tips 1 drill chuck Operating instructions

CINCINNATI PROTON 45-30G Attention: Machine in left-hand version Screw diameter: 45 mm, L/D = 30 Grooved catchment zone Motor (DC drive): 65 kW Screw speed: max. 320 rpm Tool zones: 4+1 for adapters Melt pressure & temperature sensor included EXcPRO-NT control incl. CAN bus for data communication Air conditioner for control cabinet Cylinder in bimetal design – condition: very good Screw with few operating hours – condition: very good Without material funnel & without adapter

Twin-screw extruder, corrotating, brand: OMC, type: EBV 31/32D, year: 2001. 31 mm Ø composable spindles. Book-type shirt. 11 Kw motor with water-cooled variator and wire head. Total installed power: 25 kw

Specifications: - Compaction pressure 10 bar - Volume flow 530 l/min - Power 4.0 kW - Current consumption 8 A - Voltage 400V, 50 Hz, 3~ - Speed 2,900 rpm

Kaeser CSD 122 SFC screw compressor built-in inverter 2.2-10.5m3/min, 75kW, 8.5bar Manufacturer: Kaeser Type: CSD 122 SFC Year of manufacture: 2006 Operating pressure: max 8.5bar Power: 75kW Capacity: 2.2 - 10.5 m3/min Operating hours: 96244 h (Last service: 88854 h) Inclusion dimensions: 1100 x 2200 x 1900 mm Net weight: 1600 kg

Screw compressor Kaeser type DSG 290-2 SFC A Properties: Type DSG 290-2 SFC A Order no. 4500217106 Length 3450 mm Width 1800 mm Total height 2400 mm Material No. DSG2.3 Manufacturer Serial No. 1117 Rated power 200.0 kW Speed 2982 min ̄¹ Max. operating overpressure 8.5 bar Ab. Ambient temperature min./ max. 3/40 °C

Oil-free Screw Compressor Compair D75HRS 10A 75kw 10 bar 11.4m3/min with frequency converter COMPAIR D75HRS Screw Compressor fully serviced, for sale in excellent condition oil-free design, direct drive, controlled by frequency converter. Regulated speed - air and water cooled 75kw power, air flow: 11.4 m3/min / 684m3/h Built-in frequency converter: Manufacturer: Compair D75HRS 10A Year of manufacture: 2016.11 hours: 46000 Drive power: 75Kw Pressure 10 bar Flow rate: 11.4/min Delco XL controller Main rotor speed: 2980 Voltage: 400v 50Hz 3 phase 85A Machine weight: 1890 kg Dimensions: 225 long 142 wide 205 high.

Screw Compressor: - Brand: Worthington. - Model RLR 40Ax8 - Engine: 40 hp (30 kw) - 7.5 bars. - Year: 2003.

Eccentric screw pump with 19 m³/h capacity Description: Operating pressure test: 6 bar Motor: 7.5 kW - With connections: suction side: flange DN 85, Print side: DN 100 - With chassis mobile, 2 swivels and 2 fixed castors - With cable and CE plug 16A Dimensions: Length: 1200 mm Width: 410 mm Height: 1000 mm Note: Pump 100% tested, with function guarantee On request, infinitely variable with frequency converter for an additional cost. Connections can be changed at an additional cost.

Key data: 250 , 7

Presión: 7,5 bar. Potencia: 250 kW. Velocidad de rotación: 1490 r/min. Equipado con unidad de recuperación de energía ATLAS COPCO ER S-5 (2012). Con un variador de velocidad instalado y reacondicionado LEROY SOMER POWER DRIVE MD2. N.º de serie: AIF 051684.

Key data: 250 , 7

Rotary screw air compressor. Pressure: 7.5 bar. Power: 136 kW. Rotation speed: 1488 r/min. With new screen.

2 oil-free screw air compressors Internal marking: G 101 Manufacturer: Alup Type: SCK 26-8 with 2 x 3.01 m³ compressed air per min. Compressed air up to max. 8 bar Electrical connection per machine 18.5 kW Year of Make: 2005 with control cabinet system for 2 Compressor Machines for air above heat exchangers for the temperature-controlled supply of air to the 2 Alup compressors for production- and fruit juice packaging hall with dehumidification and with a small standing compressed air tank

gebr. Compressor, Fabr. Kaeser, Type SXC 8, YOC 2010 Operating pressure 11.0 bar Power 5.5 kW

Key data: 165 mm, 330 mm, 2800 U/min

WEILER Condor lead and pull spindle lathe (overhauled) Circumferential diameter over bed 300 mm Center width 800 mm Turning diameter over carriage 170 mm Gr. workpiece weight between the tips 100 kg Bed width 240 mm Spindle bore 38 mm Spindle speeds 24 - 2800 rpm Spindle motor 3 KW Z-travel 800 mm X-travel 170 mm Z1-travel 100 mm Lead screw diameter 24 mm Thread pitches: 35 Metric 0.35 - 12 mm 40 Witworth 2 - 45 Gg / " 25 Module 0.2 - 4 Module 32 Diametrical Pitch 5 - 90 D.P. Tailstock quill stroke 110 mm Tailstock quill diameter 50 mm Tailstock quill cone 3 MK 2-axis digital display 3-jaw chuck Multifix holder B with 8 cassettes Rotating grain tip Tailstock Thread Device: Metric, Witworth, Module, Diametral Pitch Geometrically outdated!

KRAUSS MAFFEI TWIN SCREW EXTRUDER (photos before reconditioning), Mod.KMD 2-90 KK, used for profiles, n.2 parallel screws diam. 90 mm 20 L/D Max 30.5 rpm, 40 kw d.c.drive, installed power 180 kw, feeding hopper, max production with PVC profile 240 kg/h, complete with control cabinet, Heating 28.5kW,, 5 Zones Heating and 2 Last Barrel Oil Cooling Barrel +1 Zone Adapter 4 Zones Double Die, degassing point, Measures 4.3 L x 1. 2 W x 2.3 (m) H (incl Hopper) ,, Approx.weight 4.3 Ton

Make: Colchester Type / Model: Student Center width: 500 mm Passage: 42 mm Tip height: 175 mm Turning diameter over bed: 350 mm over slides: 200 mm Speed range: 34 to 1,500 mm Feed lengthwise: flat: 0.04 to 0.25 mm/rev Connection: 1.1 / 2.2 kW Accessories: Steel holder, 3-jaw chuck, 4 jaw chucks, steel bracket Weight: approx. 800 kg Dimensions: 1,550 x 900 x 1,200 mm

Tip height: 175 mm Center width: 800 mm Circumferential diameter over bed: 350 mm Circumferential diameter over support: 310 mm Spindle bore: 46 mm Speed range: 25 - 2000 rpm With digital display

pressure: 7 t weight: 0,9 t : 1417 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 2 mm, 17

Twin screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine No.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. approx. 30 1/min. Worm torque: 10,000 Nm Motor power: 3.3 - 25.0 kW, Drive motor: Commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool Heating Zones: 8 Temperature control: 12 x digital temperature controller KS 40 (PMA) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tools) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material funnel and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hoppe ...

Brand: CLECO Series: MPRO400GC Voltage: 230 V AC Frequency: 50/60 Hz Rated current: 2 A Power: Typical 250 VA Degree of protection: IP42

206 Tons Midea Inverter Water Cooled Chiller - R134a a. Cooling Capacity : 206 RT b. Total Input KW : 119.1KW c. KW/Tons : 0.5774 d. Chilled Water In/Out : 12.0/7.0 Deg C e. Fluid Flow : 124.5 M3/hr f. Evaporator Pressure Drop : 75.3 KPA g. Condenser Water In/Out : 29.4/34.4 Deg C h. Water Flow : 144.5 M3/hr i. Condenser Pressure Drop : 60.2 KPA j. Starter : VFD k. Refrigerant : R134a l. Dimension (mm) : 3538 L X 1450 W X 2130 H Incoterm: EX WORK Currency: USD Commercial: Aaron Tan (yytantopglove.com.my)

Stock# UG6388 Little used single screw extruder by Farmet (CZ) model FE100 WE Clever Max. Machine can reach output in range from 90-130 kg/h. Power consumption 16 kW. Includes water pump, die cutting knife, some toolings. Local control panel with plc controls. Previously tested on animal food production. Dims: L 195 cm x W 102.5 cm x H 178 cm x weight 600 kg.

DRAINING AUGER, construction in aisi 304 stainless steel,, case diameter (U-shape) 380 mm, total length 4.500mm,, internal stainless steel spiral diam. 230mm,, drainage with stainless steel perforated plate L=3.500 mm,, nr.6 hinged side doors,, gear motor power 2.2 kw, installed power - used power in work: about 60-65% : 2.2

Tip height: 195 mm Center width: 1250 mm large recirculating Ø over bed/support slide: 400/265 mm Spindle Holder/Bore: Camlock D1-6"/54 mm Tailstock quill taper: MK 5 Spindle speeds infinitely variable in 3 groups: 0 - 2500 rpm Feeds longitudinal: 0.018 - 1.2 mm Feed plan: 1/2 of the longitudinal feeds 51 metric thread pitches: 0.2 - 14 mm 56 Inch Thread: 2 - 56 Gg/" 20 module threads: 0.2 - 3.5 module 20 Diametrical Pitch Threads: 8 - 56 DP electr. Connection: 400 V, 7.5 kW Weight: 1500 kg Space requirement: 2500 x 1300 x 1300 mm

Specifications: Tip height: 140 mm Turning length: 500 mm Accessories (included): Lunette Multifix "A" Collets 0.5 – 24 mm Milling device (Y-axis) 3-jaw chuck 125 mm Cs Urh Axexlr Hkszorh Face Plate 260 mm Running tip Chuck Die stock 4-jaw chuck Coolant pump Instruction manual (German)

Manufacturer: Cleco / Apex Tool Group Type: TSE 961446PT Voltage: 380 V DC Current: 2-10 A DC Operating temperature: -20 to +70 °C Humidity: 0-90% without condensation You can also find the corresponding screw control in our shop!

Tip height: 355 mm Center width: 3000 mm large circulation Ø over bed/recess/bed slide: 715/790/520 mm Spindle bore: 86 mm Spindle holder according to DIN 55027: Gr. 11 Tailstock quill taper: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/flat: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitwort Thread: 2 - 28 Gg 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 Diametrical Pitch Threads: 8 - 112 DP Drive motor, pole-switchable: 380 V, 7/11 kW Weight approx.: 7 t Approx. space requirement: 6000 x 2300 mm

Mounting plate for hammer HM300 with MS03 mount, - Suitable for Hammer HM300, - Recording: MS03, - Hole pattern: 34 x 40 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Toscrew plate for hammer HM100 with MS01 holder, - Suitable for Hammer HM100, - Recording: MS01, - Hole pattern: 26 x 26 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Stock number: PM2079, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless foundation, Motor: 4 kW - 380/560 Volt - 1435 rpm., Theoretical capacity: 14000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 2, Dimensions outlet: Ø 2, Manufacturer: Mono, Type: SMH60 D8

Toscrew plate for hammer HM100 with MS01 holder, - Suitable for Hammer HM100, - Recording: MS01, - Hole pattern: 26 x 26 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Stock number: PM2078, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless foundation, Motor: 4 kW - 380/560 Volt - 1435 rpm., Theoretical capacity: 14000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 2, Dimensions outlet: Ø 2, Manufacturer: Mono, Type: MH60 D8/B

Mounting plate for hammer SB70 with MS01 mount, - Suitable for Hammer SB70, - Recording: MS01, - Hole pattern: 13.5 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Screwing plate / hammer plate / demolition grapple plate / sorting grapple plate suitable for Hammer and Mustang GRP250 and GR25

Screw-on plate with Martin M10 mount, - Suitable for demolition & sorting grapples:, - GRP450, - GR45, - GRP750, - GR75, - Mount: Martin M10, - Hole pattern: 36 x 48 cm, - Made of mechanical steel S355, - Dimensions see product pictures, - Immediately available from stock

Screw-on plate with Martin M10 mount, - Suitable for demolition & sorting grapples:, - GRP450, - GR45, - GRP750, - GR75, - Mount: Martin M10, - Hole pattern: 36 x 48 cm, - Made of mechanical steel S355, - Dimensions see product pictures, - Immediately available from stock

Screw Diameter: 140 mm // Throughput: 900 kg/h

Screw Diameter: 75 mm // Throughput: 700 kg/h

Brand Cincinnati Milacron Austria GmbH Type CMT 35 Machine number 2005723/10 Type Screw Conical Double Screw Year of manufacturing 1993 Ble Ud Dvyovl Hzgocop Machine hours 104.599 hours Screw Diameter 35 mm Dimensions (LxWxH) 3200 x 1500 x 1720 mm Weight (approx) 2000 kG

Screw Diameter: 92 mm // Throughput: 800 kg/h

Deze extruder van Cincinnati staat bij Plastima Used Machinery in de machineopslag. De machine komt uit 1999. Speciale opmerking: de extruder mist de versnellingsbak. Bj Usq Tr T Rod Dvycjlp – Merk: Cincinnati – Model: Titan 45R-APC – Bouwjaar: 1998 – Conische dubbele schroef extruder – Schroef Ø: 45 mm – Werkuren: 64.082

Screw Diameter: 130 mm // Throughput: 800 kg/h

Screw Diameter: 58 mm // Throughput: 450 kg/h

Screw Diameter: 50 mm // Throughput: 150 kg/h

Screw Diameter: 35 mm // Output Capacity: 25 kg/h

Screw Diameter: 64 mm // Throughput: 480 kg/h

Screw Diameter: 160 mm // Output Capacity: 1400 kg/h

Screw Diameter: 100 mm // Output Capacity: 600 kg/h

Screw Diameter: 27 mm // Throughput: 100 kg/h

Screw Diameter: 65 mm // Output Capacity: 170 kg/h