screw feeder used for sale

Key data: 165 mm, 330 mm, 2800 U/min

WEILER Condor lead and pull spindle lathe (overhauled) Circumferential diameter over bed 300 mm Center width 800 mm Turning diameter over carriage 170 mm Gr. workpiece weight between the tips 100 kg Bed width 240 mm Spindle bore 38 mm Spindle speeds 24 - 2800 rpm Spindle motor 3 KW Z-travel 800 mm X-travel 170 mm Z1-travel 100 mm Lead screw diameter 24 mm Thread pitches: 35 Metric 0.35 - 12 mm 40 Witworth 2 - 45 Gg / " 25 Module 0.2 - 4 Module 32 Diametrical Pitch 5 - 90 D.P. Tailstock quill stroke 110 mm Tailstock quill diameter 50 mm Tailstock quill cone 3 MK 2-axis digital display 3-jaw chuck Multifix holder B with 8 cassettes Rotating grain tip Tailstock Thread Device: Metric, Witworth, Module, Diametral Pitch Geometrically outdated!

Stock# UG6388 Little used single screw extruder by Farmet (CZ) model FE100 WE Clever Max. Machine can reach output in range from 90-130 kg/h. Power consumption 16 kW. Includes water pump, die cutting knife, some toolings. Local control panel with plc controls. Previously tested on animal food production. Dims: L 195 cm x W 102.5 cm x H 178 cm x weight 600 kg.

DRAINING AUGER, construction in aisi 304 stainless steel,, case diameter (U-shape) 380 mm, total length 4.500mm,, internal stainless steel spiral diam. 230mm,, drainage with stainless steel perforated plate L=3.500 mm,, nr.6 hinged side doors,, gear motor power 2.2 kw, installed power - used power in work: about 60-65% : 2.2

Key data: 2 mm, 17

Twin screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine No.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. approx. 30 1/min. Worm torque: 10,000 Nm Motor power: 3.3 - 25.0 kW, Drive motor: Commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool Heating Zones: 8 Temperature control: 12 x digital temperature controller KS 40 (PMA) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tools) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material funnel and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hoppe ...

Tip height: 195 mm Center width: 1250 mm large recirculating Ø over bed/support slide: 400/265 mm Spindle Holder/Bore: Camlock D1-6"/54 mm Tailstock quill taper: MK 5 Spindle speeds infinitely variable in 3 groups: 0 - 2500 rpm Feeds longitudinal: 0.018 - 1.2 mm Feed plan: 1/2 of the longitudinal feeds 51 metric thread pitches: 0.2 - 14 mm 56 Inch Thread: 2 - 56 Gg/" 20 module threads: 0.2 - 3.5 module 20 Diametrical Pitch Threads: 8 - 56 DP electr. Connection: 400 V, 7.5 kW Weight: 1500 kg Space requirement: 2500 x 1300 x 1300 mm

Specifications: Tip height: 140 mm Turning length: 500 mm Accessories (included): Lunette Multifix "A" Collets 0.5 – 24 mm Milling device (Y-axis) 3-jaw chuck 125 mm Cs Urh Axexlr Hkszorh Face Plate 260 mm Running tip Chuck Die stock 4-jaw chuck Coolant pump Instruction manual (German)

Manufacturer: Cleco / Apex Tool Group Type: TSE 961446PT Voltage: 380 V DC Current: 2-10 A DC Operating temperature: -20 to +70 °C Humidity: 0-90% without condensation You can also find the corresponding screw control in our shop!

Brand: CLECO Series: MPRO400GC Voltage: 230 V AC Frequency: 50/60 Hz Rated current: 2 A Power: Typical 250 VA Degree of protection: IP42

Tip height: 355 mm Center width: 3000 mm large circulation Ø over bed/recess/bed slide: 715/790/520 mm Spindle bore: 86 mm Spindle holder according to DIN 55027: Gr. 11 Tailstock quill taper: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/flat: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitwort Thread: 2 - 28 Gg 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 Diametrical Pitch Threads: 8 - 112 DP Drive motor, pole-switchable: 380 V, 7/11 kW Weight approx.: 7 t Approx. space requirement: 6000 x 2300 mm

power capacity: 7,5 kW feed pressure: 10 bar volume capacity: 815 dm³ /min total power requirement: 7,5 kW weight of the machine ca.: 0,4 kg Alup piston compressor - Tank 350 liters - Soundproof housing (68 dB(A) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 330 mm turning dia. in gap: 400 mm turning length: 600 mm centre distance: 750 mm spindle turning speed range: 20 - 1000 U/min spindle bore: 25 mm 3-jaw chuck: Röhm, Ø 200 mm dimensions of the machine ca.: 2000 x 800 x 1500 mm weight of the machine ca.: 1200 kg Fixed bezel Turning bezel Turning center point Three-jaw chuck Röhm, Ø 200 mm, incl. inner and outer jaws Quick-change tool holder Original Multifix size B with 2 change holders Spindle brake Tailstock quill MK3 Machine feet Lathe chuck guard Chip guard Work light The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock number: PM2079, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless foundation, Motor: 4 kW - 380/560 Volt - 1435 rpm., Theoretical capacity: 14000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 2, Dimensions outlet: Ø 2, Manufacturer: Mono, Type: SMH60 D8

Screw Diameter: 140 mm // Throughput: 900 kg/h

Stock number: PM2078, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless foundation, Motor: 4 kW - 380/560 Volt - 1435 rpm., Theoretical capacity: 14000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 2, Dimensions outlet: Ø 2, Manufacturer: Mono, Type: MH60 D8/B

Screw Diameter: 75 mm // Throughput: 700 kg/h

Brand Cincinnati Milacron Austria GmbH Type CMT 35 Machine number 2005723/10 Type Screw Conical Double Screw Year of manufacturing 1993 Ble Ud Dvyovl Hzgocop Machine hours 104.599 hours Screw Diameter 35 mm Dimensions (LxWxH) 3200 x 1500 x 1720 mm Weight (approx) 2000 kG

Screw Diameter: 92 mm // Throughput: 800 kg/h

Deze extruder van Cincinnati staat bij Plastima Used Machinery in de machineopslag. De machine komt uit 1999. Bj Usq Tr T Rod Dvycjlp – Merk: Cincinnati – Model: Titan 45R-APC – Bouwjaar: 1998 – Conische dubbele schroef extruder – Schroef Ø: 45 mm – Werkuren: 64.082

Screw Diameter: 130 mm // Throughput: 800 kg/h

Screw Diameter: 58 mm // Throughput: 450 kg/h

Screw Diameter: 50 mm // Throughput: 150 kg/h

Screw Diameter: 35 mm // Output Capacity: 25 kg/h

Screw Diameter: 64 mm // Throughput: 480 kg/h

Screw Diameter: 160 mm // Output Capacity: 1400 kg/h

Screw Diameter: 100 mm // Output Capacity: 600 kg/h

Screw Diameter: 27 mm // Throughput: 100 kg/h

Screw Diameter: 65 mm // Output Capacity: 170 kg/h

• One pair of original WEBER screws (excellent state, including measurement report • One pair of non-original screws Be Udowaxuae Dvycsww • Gearbox inspected and partially revised by WEBER • Control upgraded to WPS-control • Output on PVC around 700 kg/hour

Merk: Leistritz AG Model: Micro 27/40 D Type schroef: Dubbele schroef Bouwjaar: 1993 Schroef Ø: 27 mm L/D-verhouding: 40 Werkuren: 2.466 Bws Ud Dvyju Aqdkocjw

Mobile screw compactor Pöttinger BJ 2019

turning diameter over bed: 360 mm turning diameter over slide rest: 180 mm turning length: 900 mm turning speed range: 25 - 1600 U/min total power requirement: ca. 3 kW weight of the machine ca.: 1,5 t dimensions of the machine ca.: 2,5 x 1 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Brand: Atlas Compo Type: GX5C FF with integrated refrigeration dryer Kind: Screw compressor Serial number: AII642955 Chassis number: 8152101195 Year of construction: 2004 Cooling: Air-cooled Weight: 198kg. Assets: 5.5 kW Sound level: 64 dBA Work pressure: 10 Bar Compressed air: Capacity Approx. 10.0- 10.1 liters/second Length mm: 145cm Width mm: 55cm Height mm: 130cm State machine: Very good Electrical connection: 3 phase Missing parts: No Photos/film available: Photos available 10.2.192

Brand: Boge Type: C3LR Kind: Screw compressor, air-cooled Max. final pressure: 10 bar Chassis number: 5063340 Year of construction: 2013 Capacity: 0.24 m3/min. = 8.3 CFM Engine speed: 1,500/ min. Drive power: 2.2 kW (3 hp) Pressure vessel: 90 liter Voltage: 400V / 50Hz (3-phase) L x W x H: 1185 x 550 x 1010 Noise level: 61 dB (A) Weight: Approx. 130 kg Residual oil content: < 3 mg/m³ Connection: G ½” (ball valve) Cooling air volume: 600 m³/h Ambient temperature range: +5 to +40 °C Photos/film available: Photos available 10.2.195

turning diameter over bed: 800 mm turning diameter over slide rest: 540 mm turning length: 4000 mm centre height: 400 mm centre distance: 4000 mm spindle turning speed range: 9 - 1140 U/min weight of the machine ca.: 8,0 t - with gap with insert - Accessories: 3-jaw chuck FORKARDT 400 mmø, 4-jaw chuck 500 mmø, faceplate 800 mmø, DRO on X-and Z-axis ACU-RITE, MULTIFIX-head with various inserts, 2 solid steadies, 1 running steady, running center, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 460 mm turning length: 1250 mm centre height: 230 mm centre distance: 1250 mm spindle turning speed range: 35 - 1800 U/min weight of the machine ca.: 2,7 t Accessories: 3-jaw chuck 250 mmø, MULTIFIX-head with 3 inserts, solid steady The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 72 mm

We can offer a W&P extruder. 75/36, year 2004, stopped, working condition.

Key data: 58 mm

We can offer a Toshiba extruder. 58/40, year 2010, stopped, working condition.

turning diameter over bed: 500 mm turning diameter over slide rest: 320 mm turning length: 2100 mm centre height: 250 mm : mm spindle bore: 60 mm spindle turning speed range: 11 - 2000 U/min total power requirement: 7,0 kW weight of the machine ca.: 2,9 t dimensions of the machine ca.: 4,3 x 1,2 x 1,3 mm Lathes with: - 4-position tool post - 3-jaw chuck 315mm - Centering point The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 0350 mm : 196 mm : 0650 mm : 170 mm : 42 mm : 7,5 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

greates pass round over bed: 810 mm swing diameter over face slide: 560 mm centre distance: 2000 mm bed width: 480 mm slide valve travel: 400 mm upper head travel: 180 mm turning tool - shaft cross cut: 32 x 25 mm power capacity: 22 kW max. torque on the spindle: 3200 Nm spindle head: Gr. 11, DIN 55027 spindle diameter in front bearing: 152,4 mm spindle bore: 106 mm turning speed range: 9 - 1800 U/min turning speeds: 24 longitudinal feeds:: 0,092 - 41 mm/U face feeds: 0,046 - 20 mm/U metric threading: 0,5-112 mm inch threading: 1/4 - 56 G/1 thread - module: 0,125 - 28 mm thread - DP: 1 - 224 Pitch tailstock quill diameter: 115 mm quill stroke: 225 mm taper of tail spindle: MK 6 max. workpiece weight between centres: 2000 kg max. workpiece weight -without tailstock: 750 kg 3-jaw chuck: Röhm, Ø Overall size: ca. 4600x1900x1600 mm weight: ca. 4300 kg Number of feed stages and threads: 99  ...

Offer 25432 Specifications: - Turning diameter 320 mm - Center width 750 mm - Largest turn – Ø over bed 550 mm - via flat slide 175 mm - Spindle bore 32 mm - Spindle holder - Pick-up cone of the tailstock quill MK 3 - Quill stroke 180 mm - 18 spindle speeds 85 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches -Thread - Module thread - Diametrical Pitsch thread -Arbor - Cheek chuck -Lunette - Drive 400 V / 2.2 kW - Space requirement approx. W 2100 x D 750 x H 1300 mm - Weight approx. 750 kg

Weiler Commodor – lead and pull spindle lathe (partially overhauled, built approx. 1990) Condition: Partially overhauled, very good general condition Year of construction: approx. 1990 Manufacturer: Weiler Model No.: Commodor Machine Type: Lead and Pull Spindle Lathe Technical data (approx. information): Max. turning diameter over bed: 380 mm Max. turning diameter over support: 190 mm Max. turning length: 1000 mm Bar Passage: 56 mm Speed range: 25 – 2000 rpm Spindle Nose: A2-6 Drive power: 4.0 kW Tailstock: MK4 Automatic longitudinal and flat feeds: 0.011 – 0.80 mm/rev Thread ranges: Metric: 0.3 – 10 mm Inch: 80 – 2 3/4 G/" Diametrically Pitch: 80 – 5.5 Dp Module: 0.2 – 5 Dimensions (L x W x H): 2200 × 1200 × 1800 mm Weight: approx. 1500 kg ⚙️ Equipment & Accessories: 3-Axis Digital Display SINO (New)  ...

turning diameter over bed: 370 mm turning diameter over slide rest: 200 mm turning length: 1000 mm centre height: 185 mm spindle bore: 56 mm tailstock quill taper MT: 4 turning speeds: 50 - 2000 U/min power capacity: 4,0 kW weight of the machine ca.: 1,4 t dimensions of the machine ca.: 2,3 x 1,1 x 1,3 m Center lathe 200mm three-jaw chuck Size B Multifix tool post 3 Multifix tool holders Emergency stop device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 460 mm turning diameter over slide rest: 280 mm turning length: 1000 mm centre height: 230 mm : 720 mm spindle bore: 53 mm spindle turning speed range: 28 - 1250 U/min total power requirement: 4,0 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 2,4 x 1,4 x 1,75 mm Lathes with: - Digital display - Quick-release tool post - 3-jaw chucks (200 mm and 160 mm) - Chip tray - Centering center The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

feed pressure: 8,5 bar liter capacity: . l total power requirement: 454 kW weight of the machine ca.: t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ALMIG Combi 15-10 rotary screw air compressor YOM 2012. Never used. Motor speed 3000 rpm Motor power 15 kW Volume flow m3/min- 1.84 Volume m3/hour- 110 Max. pressure 10 Bar. Air Receiver Capacity 500L

turning diameter over bed: 400 - 900 mm turning diameter over slide rest: ? mm turning length: 1000 - 1500 mm total power requirement: ? kW weight of the machine ca.: t dimensions of the machine ca.: m Free at short notice due to current company resolution In use until the end Untested, wear and tear due to age and use Machine package 5 x lathe 2 x CAZENEUVE HB 500 1 x WEISSER Junior 1 x SCHAERER UD 630 x 1500 1 x ERNAULT SOMUA HN 500 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Digital Center height 150 mm Circulation over bed 300 mm Center width 1000 mm 3-jaw chuck, Arbor Chip protection Chip tray

Dimensions (L/W/H): 1950x690x1700 mm Weight: 431 kg Total power requirement: 7,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 1950x690x1700 mm Weight: 426 kg Total power requirement: 5,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.