screw compressor used for sale

Stock number: D2025, Screw conveyor, stainless steel,, estimated 1,5 kW motor, 380 volt., U-profile,, Ø 320 x L 1720 mm., Material: Stainless steel AISI 304, Dimensions: Ø 320 x L 1720 mm.

Stock number: D1195, Screw conveyor, stainless steel/steel 37,, u-profile., 1,1 kW. gear motor,, 220/380 Volt., 28 rpm., Ø 230 x L 2000 mm., (Fits SD067)., Material: Stainless steel AISI 304/steel 37, Dimensions: Ø 230 x L 2000 mm.

Stock number: D1181, Screw conveyor, stainless steel,, 0,55 kW gear motor., 121 rpm,, 220/380 Volt., U-type with lid and washing pipe,, obliquely placed on legs., Ø 200 x L 1700 mm., Material: Stainless steel AISI 304, Dimensions: Ø 200 x L 1700 mm.

Stock number: D1154, Screw conveyor, stainless steel,, o-profile., 1,1 kW. gear motor,, 230/400 Volt., Ø 130 x L 3050 mm. screw., Material: Stainless steel AISI 304, Dimensions: Ø 130 x L 3050 mm.

Stock number: D1122, Screw conveyor, stainless steel,, o-profile., 0,37 kW. gear motor,, 380 Volt., Ø 140 x L 1580 mm., Material: Stainless steel AISI 304, Dimensions: Ø 140 x L 1580 mm.

Stock number: D1118, Screw conveyor, stainless steel,, u-profile, with 3 pcs. of removable lids., 0,75 kW. gear motor,, 133 rpm., 220/380 Volt., Ø 125 x L 2500 mm., Material: Stainless steel AISI 304, Dimensions: Ø 125 x L 2500 mm.

Stock number: D1117, Screw conveyor, stainless steel,, u-profile, with lid., Double jacket., Insulated, outer fully welded stainless cladding,, 1,5 kW gear motor., 26,24 rpm., 230/400 Volt., Ø 300 x L 4170 mm., Material: Stainless steel AISI 304, Dimensions: Ø 300 x L 4170 mm.

Stock number: D1042, Screw conveyor, stainless steel,, U-profile with lid and inlet hopper., Standing in leg rack,, Ø 250 x L 1730 mm., 2,2 kW gear motor,, 64 rpm., 380/415 volt., Material: Stainless steel AISI 304, Dimensions: Ø 250 x L 1730 mm.

QUICK WASHER for RIGID and SOFT PLASTICS, made in AISI304 stainless steel, low water consumption, can be used with hot water or mild detergents, for reground LDPE LLDPE HDPE film, rigid PE PP PVC PET PA ABS PS PC, 7,5 kw motor 400V 50/60Hz, inner auger 400 mm diam., length 3.000 mm., material and water are loaded from the bottom, material discharging is done through a draining auger from top, bearings are positioned outside the wet chamber, seals on the lower bearing to exclude any contact with water, auger speed (and throughput rate) can be adjustable to change throughput rate 500 to 1.000 kg/h, by adding an inverter, Low water consumption (depending on contamination), The water can be mechanically filtered with a [water screening system](.germanplast.eu/listings/5003567-germanplast-vibrating-screen- round-type) (available separately), This machine is to be electrically connected to an  ...

Stock number: PM2076, Eccentric screw pump, stainless acid proof steel,, Seepex type BT 2-12., 1,5 kW. gear motor,, 220/380 V., 186 rpm., Screw feeding,, inlet flange L 350 x W 180 mm., Theoretical capacity 1.000 l/h., Material: Stainless acid proof steel AISI 316

PVC PROFILE EXTRUSION LINE EVC BRAND, single screw extruder with 60 mm 28 LD, constructed in 1998, for 180 mm max width, 44 kw drive, control panel, Calibrating desk 3,7 m.long with 1 x 9 kw.pump, Caterpillar pull off unit, 180 mm wide, saw, 6,0 mt.long discharging table.

MARIS TWIN SCREW EXTRUDER, Loading hopper for regrinds, Barrel with 2 x 92 mm screws 40 L/D, co-rotating parallel screws for polyolefines, CEAR d.c.motor, N.2 vacuum degassing pumps, 4-plate semi-automatic screenchanger, hydraulic pack, Average throughput rate around 1 Ton/h, Water ring pelletizer, drying centrifuge, Electrical control panel, The machine is offered as is or checked

MARIS TWIN SCREW EXTRUDER, Barrel with 2 x 92 mm screws 40 L/D, n.2 vacuum degassing pumps, co-rotating parallel screws for polyolefines, complete with 4-plate semi-automatic screenchanger, hydraulic pack, Average throughput rate around 1 Ton/h, Water ring pelletizer, drying centrifuge, electric cabinet, The machine is offered as is or reconditioned

MARIS TWIN SCREW EXTRUDER, Type TM 85 LC 37 L/D, dosing unit for granulated materials, barrel with 2 x 85 mm co-rotating screws 37 L/D, max screw rpm : 152, vacuum degassing pump 4,5 kw drive, Present capacity 450 kg/h depending on materials and feeding rate, 64 kw drive, Constructed in 1992, offered AS IS or reconditioned, installed power - used power in work: about 60-65% : 64, screws diam.: 85 mm. 37 L/D, screws: co-rotating

QUICK WASHER for RIGID and SOFT PLASTICS, made in AISI304 stainless steel, low water consumption, can be used with hot water or mild detergents, for reground LDPE LLDPE HDPE film, rigid PE PP PVC PET PA ABS PS PC, 7,5 kw motor 400V 50/60Hz, inner auger 400 mm diam., length 3.000 mm., material and water are loaded from the bottom, material discharging is done from top, bearings are positioned outside the wet chamber, seals on the lower bearing to exclude any contact with water, auger speed is adjustable to change throughput rate 500 to 1.000 kg/h, throughput rate can be adjusted according to contamination and material, Low water consumption (depending on contamination) About 60 lt., The water can be mechanically filtered with a [water screening system](.germanplast.eu/listings/5003567-germanplast-vibrating-screen- for-water-powder-granule) (available separately) to be reused in the proces ...

FBM plastic extruder with Ø 120 mm spindle and underwater head cutting. Ideal for recycling and granulation lines. Brand: FBM (Falzoni) Model: ETF 120 V 380/5L Motor: 200 kW (270 hp) L/D ratio: 35 Underwater cutting (PRT, 2006) Includes: force-fed silo Extras: degasser and filter changer Year: 1988

Key data: 35 mm, 25 , 103 U/min

Used extruder 35mm - 25 l/d with 5.6 kW drive 3-zone auger 3 heating/cooling zones on the cylinder + 1 tool zone Mass pressure sensor 500 bar All machine cables designed to be plugged in Control cabinet with main switch, motor controller, mass pressure indicator and 4 pieces of temperature controller Function-tested

Key data: 63 mm, 1300

Twin screw extruder, conical Manufacturer: Reifenhäuser Type: BT 1000-2-63 K Year of construction: 1994 Serial No.: 32061 Working hours: 32,303 h Screw geometry: conical for PVC-hard profiles Screw diameter: 63 – 121 mm Screw length: 1300 mm Screw speed: max. approx. 32 1/min. Nominal torque of the gearbox: 1000 daNm Dynamic load rating of the return pressure bearing: 103600 daN Engine power: 43.0 kW, Drive motor: Baumüller DC motor Cylinder heating/cooling zones: 4/3 (air cooling with fan) Adapter heating zones: 1 Tool Heating Zones: 5 Temperature control: digital temperature controller (2 x PSG Multipact 88) Max. permissible mass pressure: 500 bar Output capacity: approx. 150 - 200 kg/h for PVC-rigid profiles Accessories: Dosing device and material hopper Extrusion height: 1150 mm Dimensions: 4250 x 1200 x 1750 mm without hopper (LxWxH) Weight: approx. 3000 k ...

Stock# U2457-3 Used stainless steel horizontal screw conveyer by Van Beek BV (NL) type "U", model TR300. Width of the gutter 315 mm. Screw has diameter 300 mm, lead of the screw 270 mm, total length of the screw 290 cm. Conveyer has two inlets, each with diameter 298 mm and rotary magnetic separator by Goudsmit Magnetic Systems (NL). Each separator is driven by el motor and reducer 0.18 kW, 1320/21 rpm, 220-240/380-415 V, 50 Hz. Spacing between center axis of each inlet is 145 cm. Conveyer has also two rectangular discharge outlets, each with dimensions: 240 mm x 250 mm. Spacing between centers of discharge outlets - 250 cm. Screw is driven via reducer and el motor 2.2 kW, 220-240/380-415 V, 50 Hz. Working rotation of screw up to 64 rpm. Last time machine had been working in food industry as a collector of powdered products from two vibrating screens.

Key data: 180 mm, 2000 U/min

Built in 1990 Center height 180 mm Turning diameter over carriage 190 mm Center width 1,000 mm Spindle passage 55 mm Max. spindle speed 13-2,000 rpm Spindle drive 7.5 kW Quill stroke 150 mm (MK4) Machine weight 1,650 kg Accessories: Digital display, 3-jaw chuck, quick-change steel holder with 4 inserts, 2 steady rests, coolant device.

Ball screw with servo motor SIEMENSLinear guide with permanent servo motor SIEMENSTyp: 1FK6044-7AH71-1EG0Ident No. YF RN22 5076 01 001Year of construction: 2003Axle movement: 540 mmTotal length: 900 mmShaft diameter: 40 mmThread pitch: 40 mmBall diameter: approx. 6 mm- Compact unit with servo motor and spindle nut- Ball screw guided in a torsion-proof manner, drive via nut- Ball screw 40 mm (hollow shaft, inner diameter = approx. 22mm)- Permanent servo motor SIEMENS type: 1FK6044-7AH71-1EG0 (Serial No.: Ident No. YF RN22 5076

Hethon 71 Hopper and screw feed 2018, stainless, 100Kg hopper and outfeed screw, screw diameter 60mm, 3Ph, two in stock

This offer is aimed exclusively at entrepreneurs within the meaning of § 14 BGB. The price is net plus 19% VAT. Manufacturer: EST Ticino Type: ET-BM 400 Turning length: 1500 mm Turning diameter bed Ø: 800 mm Turning diameter slide: 470 mm Turning diameter pit Ø: 400 mm Pit length: 750 mm Spindle bore: 130 mm Power spindle: 15 kW Bed width: 600 mm Quill: 130 Ø Stroke quill: 300 mm Spindle mount: 6 Mk Speed: 600 rpm Dimensions (estimated) Length: 4500 mm Width: 1800 mm Height: 1800 mm Weight: 5200 kg with accessories: -Safety equipment - Face plate, four-jaw chuck, clamping jaws, tool holders, tips, drill chucks, tools All information is made to the best of our knowledge, errors excepted. The sale is subject to exclusion of any warranty. The exclusion does not apply to claims for damages arising from grossly negligent or intentional breach of the S ...

Lead and pull spindle lathe WEIPERT Year of Make: 1956 Spindle bore: 90 mm Center width: 3000 mm Circulation Ø over bed : 800 mm Circulation 0 over slide: 610 mm Circulation 0 in offset: 1120 mm Speed range: 7.5 – 475 rpm With the following accessories: Multifix tool holder with 11 inserts Coolant Setup Three-jaw chuck 0315 mm Three-jaw chuck 0 400 mm Three-jaw chuck 0 500 mm Face Plate 0 400 mm Face Plate 0 800 mm Face Plate 0 1000 mm Running Lynette Various turning tools (30 pcs. indexable insert tools) 2 moving centering tips 1 drill chuck Operating instructions

CINCINNATI PROTON 45-30G Attention: Machine in left-hand version Screw diameter: 45 mm, L/D = 30 Grooved catchment zone Motor (DC drive): 65 kW Screw speed: max. 320 rpm Tool zones: 4+1 for adapters Melt pressure & temperature sensor included EXcPRO-NT control incl. CAN bus for data communication Air conditioner for control cabinet Cylinder in bimetal design – condition: very good Screw with few operating hours – condition: very good Without material funnel & without adapter

Twin-screw extruder, corrotating, brand: OMC, type: EBV 31/32D, year: 2001. 31 mm Ø composable spindles. Book-type shirt. 11 Kw motor with water-cooled variator and wire head. Total installed power: 25 kw

Eccentric screw pump with 19 m³/h capacity Description: Operating pressure test: 6 bar Motor: 7.5 kW - With connections: suction side: flange DN 85, Print side: DN 100 - With chassis mobile, 2 swivels and 2 fixed castors - With cable and CE plug 16A Dimensions: Length: 1200 mm Width: 410 mm Height: 1000 mm Note: Pump 100% tested, with function guarantee On request, infinitely variable with frequency converter for an additional cost. Connections can be changed at an additional cost.

KRAUSS MAFFEI TWIN SCREW EXTRUDER (photos before reconditioning), Mod.KMD 2-90 KK, used for profiles, n.2 parallel screws diam. 90 mm 20 L/D Max 30.5 rpm, 40 kw d.c.drive, installed power 180 kw, feeding hopper, max production with PVC profile 240 kg/h, complete with control cabinet, Heating 28.5kW,, 5 Zones Heating and 2 Last Barrel Oil Cooling Barrel +1 Zone Adapter 4 Zones Double Die, degassing point, Measures 4.3 L x 1. 2 W x 2.3 (m) H (incl Hopper) ,, Approx.weight 4.3 Ton

Make: Colchester Type / Model: Student Center width: 500 mm Passage: 42 mm Tip height: 175 mm Turning diameter over bed: 350 mm over slides: 200 mm Speed range: 34 to 1,500 mm Feed lengthwise: flat: 0.04 to 0.25 mm/rev Connection: 1.1 / 2.2 kW Accessories: Steel holder, 3-jaw chuck, 4 jaw chucks, steel bracket Weight: approx. 800 kg Dimensions: 1,550 x 900 x 1,200 mm

Tip height: 175 mm Center width: 800 mm Circumferential diameter over bed: 350 mm Circumferential diameter over support: 310 mm Spindle bore: 46 mm Speed range: 25 - 2000 rpm With digital display

Key data: 165 mm, 330 mm, 2800 U/min

WEILER Condor lead and pull spindle lathe (overhauled) Circumferential diameter over bed 300 mm Center width 800 mm Turning diameter over carriage 170 mm Gr. workpiece weight between the tips 100 kg Bed width 240 mm Spindle bore 38 mm Spindle speeds 24 - 2800 rpm Spindle motor 3 KW Z-travel 800 mm X-travel 170 mm Z1-travel 100 mm Lead screw diameter 24 mm Thread pitches: 35 Metric 0.35 - 12 mm 40 Witworth 2 - 45 Gg / " 25 Module 0.2 - 4 Module 32 Diametrical Pitch 5 - 90 D.P. Tailstock quill stroke 110 mm Tailstock quill diameter 50 mm Tailstock quill cone 3 MK 2-axis digital display 3-jaw chuck Multifix holder B with 8 cassettes Rotating grain tip Tailstock Thread Device: Metric, Witworth, Module, Diametral Pitch Geometrically outdated!

Stock# UG6388 Little used single screw extruder by Farmet (CZ) model FE100 WE Clever Max. Machine can reach output in range from 90-130 kg/h. Power consumption 16 kW. Includes water pump, die cutting knife, some toolings. Local control panel with plc controls. Previously tested on animal food production. Dims: L 195 cm x W 102.5 cm x H 178 cm x weight 600 kg.

206 Tons Midea Inverter Water Cooled Chiller - R134a a. Cooling Capacity : 206 RT b. Total Input KW : 119.1KW c. KW/Tons : 0.5774 d. Chilled Water In/Out : 12.0/7.0 Deg C e. Fluid Flow : 124.5 M3/hr f. Evaporator Pressure Drop : 75.3 KPA g. Condenser Water In/Out : 29.4/34.4 Deg C h. Water Flow : 144.5 M3/hr i. Condenser Pressure Drop : 60.2 KPA j. Starter : VFD k. Refrigerant : R134a l. Dimension (mm) : 3538 L X 1450 W X 2130 H Incoterm: EX WORK Currency: USD Commercial: Aaron Tan (yytantopglove.com.my)

DRAINING AUGER, construction in aisi 304 stainless steel,, case diameter (U-shape) 380 mm, total length 4.500mm,, internal stainless steel spiral diam. 230mm,, drainage with stainless steel perforated plate L=3.500 mm,, nr.6 hinged side doors,, gear motor power 2.2 kw, installed power - used power in work: about 60-65% : 2.2

Key data: 2 mm, 17

Twin screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine No.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. approx. 30 1/min. Worm torque: 10,000 Nm Motor power: 3.3 - 25.0 kW, Drive motor: Commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool Heating Zones: 8 Temperature control: 12 x digital temperature controller KS 40 (PMA) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tools) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material funnel and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hoppe ...

Tip height: 195 mm Center width: 1250 mm large recirculating Ø over bed/support slide: 400/265 mm Spindle Holder/Bore: Camlock D1-6"/54 mm Tailstock quill taper: MK 5 Spindle speeds infinitely variable in 3 groups: 0 - 2500 rpm Feeds longitudinal: 0.018 - 1.2 mm Feed plan: 1/2 of the longitudinal feeds 51 metric thread pitches: 0.2 - 14 mm 56 Inch Thread: 2 - 56 Gg/" 20 module threads: 0.2 - 3.5 module 20 Diametrical Pitch Threads: 8 - 56 DP electr. Connection: 400 V, 7.5 kW Weight: 1500 kg Space requirement: 2500 x 1300 x 1300 mm

Specifications: Tip height: 140 mm Turning length: 500 mm Accessories (included): Lunette Multifix "A" Collets 0.5 – 24 mm Milling device (Y-axis) 3-jaw chuck 125 mm Cs Urh Axexlr Hkszorh Face Plate 260 mm Running tip Chuck Die stock 4-jaw chuck Coolant pump Instruction manual (German)

Manufacturer: Cleco / Apex Tool Group Type: TSE 961446PT Voltage: 380 V DC Current: 2-10 A DC Operating temperature: -20 to +70 °C Humidity: 0-90% without condensation You can also find the corresponding screw control in our shop!

Brand: CLECO Series: MPRO400GC Voltage: 230 V AC Frequency: 50/60 Hz Rated current: 2 A Power: Typical 250 VA Degree of protection: IP42

Tip height: 355 mm Center width: 3000 mm large circulation Ø over bed/recess/bed slide: 715/790/520 mm Spindle bore: 86 mm Spindle holder according to DIN 55027: Gr. 11 Tailstock quill taper: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/flat: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitwort Thread: 2 - 28 Gg 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 Diametrical Pitch Threads: 8 - 112 DP Drive motor, pole-switchable: 380 V, 7/11 kW Weight approx.: 7 t Approx. space requirement: 6000 x 2300 mm

Stock number: PM2079, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless foundation, Motor: 4 kW - 380/560 Volt - 1435 rpm., Theoretical capacity: 14000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 2, Dimensions outlet: Ø 2, Manufacturer: Mono, Type: SMH60 D8

Mounting plate for hammer HM300 with MS03 mount, - Suitable for Hammer HM300, - Recording: MS03, - Hole pattern: 34 x 40 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Stock number: PM2078, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless foundation, Motor: 4 kW - 380/560 Volt - 1435 rpm., Theoretical capacity: 14000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 2, Dimensions outlet: Ø 2, Manufacturer: Mono, Type: MH60 D8/B

Toscrew plate for hammer HM100 with MS01 holder, - Suitable for Hammer HM100, - Recording: MS01, - Hole pattern: 26 x 26 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Screw-on plate with Martin M10 mount, - Suitable for demolition & sorting grapples:, - GRP450, - GR45, - GRP750, - GR75, - Mount: Martin M10, - Hole pattern: 36 x 48 cm, - Made of mechanical steel S355, - Dimensions see product pictures, - Immediately available from stock

Toscrew plate for hammer HM100 with MS01 holder, - Suitable for Hammer HM100, - Recording: MS01, - Hole pattern: 26 x 26 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock

Mounting plate for hammer SB70 with MS01 mount, - Suitable for Hammer SB70, - Recording: MS01, - Hole pattern: 13.5 cm, - made of machine steel S355, - Dimensions see product images, - Available immediately from stock