sc used for sale

in nieuwstaat 2 Atlas Copco Freqentiegeregelde lage druk compressoren Max 4 Bar max 93 Kw 200 bedrijfsuren

nieuwe schroefcompressor 4 Kw op ketel met droger

TOS Galanta SUIL 40A – Lead and Pull Spindle Lathe For sale is a well-preserved and mechanically overhauled 2009 TOS Galanta SUIL 40A lead and pull spindle lathe, built in 1998. Specifications Manufacturer: TOS Model: Galanta SUIL 40A Machine number: 0219 Year of manufacture: 1998 (mechanically overhauled 2009) Dimensions: approx. 2.2 m × 1.1 m × 1.75 m Weight: 1620 kg Main drive: 5.5 kW Spindle speed (max.): 3150 rpm Spindle bore: 50.2 mm Center spacing: 1000 mm Center height: 200 mm Turning diameter over bed: 400 mm Condition: ready for use (used) Accessories Three-jaw chuck Tailstock Lunette Coolant Setup Interchangeable Wheel Set Operating instructions (German) The machine is fully functional. Viewing possible by appointment

Manufacturer: Zentner Systems GmbH Model: Soltec ST 100 Year of Make: 2006 Serial number: 0505 / 06 Operating voltage: 3 × 400 V Mains frequency: 50 Hz Operating power: 3 kW Operating pressure (air): 6.0 bar Design: Closed stainless steel screen washing cabin Application: Automatic cleaning of screen printing frames Particularities: – EX signs available – Integrated exhaust air / exhaust system – Compact design with its own control cabinet Location: Schierling Viewing possible by appointment.

Key data: 22 mm, 60

Single screw extruder 60 with renewed PMA control in 2010 - was replaced by double screw 5 years ago. Works after oil and belt change

feed pressure: 8,5 bar liter capacity: . l total power requirement: 454 kW weight of the machine ca.: t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ALMIG Combi 15-10 rotary screw air compressor YOM 2012. Never used. Motor speed 3000 rpm Motor power 15 kW Volume flow m3/min- 1.84 Volume m3/hour- 110 Max. pressure 10 Bar. Air Receiver Capacity 500L

Digital Center height 150 mm Circulation over bed 300 mm Center width 1000 mm 3-jaw chuck, Arbor Chip protection Chip tray

Motor power: 45 kW Nominal flow rate: 7.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1500x1000x1265 mm Estimated weight: about 700 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-4

A twin screw extruder is offered. Drive: ASEA electric motor type ACA 200-6L, 50.5kW, 1460rpm. Inspection possible by prior arrangement.

Motor power: 11 kW Nominal flow rate: 1.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-2

A screw compressor is offered. Maximum pressure 10bar, volume flow approx. 2020l/min (2.02m3/min) with separate compressed air tank, galvanized. Viewing possible by appointment.

Motor power: 7.5 kW Nominal flow rate: 1.0 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 900x625x860 mm Estimated weight: about 200 Kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-1

Motor power: 15 kW Nominal flow rate: 1.7 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-3

Offered are 2 screw compressors with the following features per unit: Power: 15kW, pressure: 10bar, volume flow: 1950l/min (1.95m3/min), speed: 2930rpm, including sound enclosure, 1) year of construction 1989, operating hours: approx. 38100h, 2) year of construction 1986, operating hours: approx. 10600h. Inspection possible by appointment.

✨ Grab it now †your top scaffold deal! ✨ We’ve got a 100 m² facade scaffold with a system width of 1.09 m , ready to use right away. The package includes a walk-through frame, adjustable base jacks, and everything you need for your next project. 🏗️ This set is based on the proven Layher Blitz frame scaffold and combines durable materials, high stability, and easy handling . The steel or aluminum decks are particularly long-lasting, and the integrated walk-throughs with ladders make working comfortable and safe. Thanks to the standardized 2.57 m frame length , the scaffold can be easily expanded and is fully compatible with all original components. 💪 The plug-in system allows for quick assembly and disassembly, saving valuable time on the construction site. At the same time, the sturdy design ensures you can work safely ...

🚨 Be quick †limited stock! We offer top Layher Blitz scaffold packages †100  m ² of fa çade scaffolding , system width 1.09  m . Includes access deck with ladder, base jacks, and everything you need to get started. The complete set for your next façade scaffold project †ready to use and available while supplies last . ⚡   This package is based on the proven Layher Blitz frame scaffold system with a 1.09 m system width. It includes heavy-duty steel or aluminium decks, access decks with integrated ladders, diagonal braces for structural stability, and base jacks for safe height adjustment †all original Layher components .   Thanks to the standardized 2.57 m bay length, the system is easy to expand and fully compatible with other Layher Blitz parts †ideal for professionals who want to work quickly ...

Two identical compressors with integrated refrigerated dryer are offered. Pressure dew point: +3°C, rated power: 30kW, delivery rate (FAD): 5.31m³/min at 8bar, 4.77m³/min at 10bar, 3.86m³/min at 13bar, control: Boge Autotronic, fully automatic operation. Inspection is possible by arrangement.

BANDERA TWIN SCREW PVC PIPES EXTRUDER, for pipes with min/max diam.40/200 mm., extruder with n.2 parallel counter-rotating screws Ø 90 mm, Throghput rate 400 kg/hr, missing of screenchamger (can be added separately), n.2 dies available 40 to 125 mm + 125 to 200 mm., Tooling from 40-200 mm (available diam. 100 mm for O-Ring), Bandera 6 mt.long vacuum calibration tank, IPM haul off unit, IPM saw, IPM belling unit, constructed in 1998, totally refurbished in 2006 by Plasco, machine now disconnected, offered RECONDITIONED., availability: immediate, working width: 40-200 mm Ø, capacity: 400 kg/h, conditions: disconnected, type: pipes extrusion line

Vacuum extrusion press 'UNIVERSA' PZG 40-40a with 400 mm Ø and 18.5 kW drive (expandable up to 55 kW). Maximum pressing pressure: 30 bar. Extruder incl. PZSVG 35a pre-press with 15 kW drive. Includes base frame with motor clamping device. In regularly serviced condition; last revision in 2022. Previous use: Production of ceramic roof tiles. Available for an extra charge: vacuum generator and various mouthpieces.

Please refer to Fig. 2 for technical data

Please refer to Fig. 2 for technical data

Please refer to Fig. 2 for technical data

We can offer Krauss maffei extruder,moder ZE90A, manufactured in 2013, main motor power 884kw, large output, installed and used, auxiliary equipments available, serious buyer contact us.

We stock numerous lengths of this type, e.g. 220 / 270 / 320 / 370 / 420 / 470 / 520 / 570 / 620 / 670 / 720 / 770 / 820 / 870 / 920 / 970 / 1020 / 1120 mm and others. All scales are thoroughly cleaned and checked for perfect function before delivery. The prices are – depending on the length – between 290 and 370 EUR. Please ask us for the exact prices. Please note that these are exchange prices.

We can offer Krauss maffei extruder,moder ZE90A, manufactured in 2013, main motor power 884kw, large output, installed and used, auxiliary equipments available, serious buyer contact us.

Manufacturer: ESC Model: ESC-AT-60PD Type of Machine : Screen Printing Machine Semi-automatic, universal, digitally controlled precision screen printing machine for flexible and rigid materials up to 200 mm material thickness STANDARD EQUIPMENT/FEATURES - Programmable PLC control system - User-friendly operation via touch screen - High-quality linear guides for smooth, low-noise motion - Vertical, motor-driven screen frame lifting with synchronized stripping motion - Precision print head with pneumatic lift for screen change and cleaning - Digital input of desired print parameters: - Speed for print and flood squeegee - Print height - Print stroke length - Neutral position for print and flood squeegee - Single-function control for setup operation - Single-cycle operation via foot switch and automatic cycle mode - Extremely short setup times without the need for tools - Pneumatic scr ...

L+Z Lathe WEILER Praktikant 160 – Partially Overhauled Machine in very good used condition – delivery on order, delivery time by arrangement! ✅ Technical data Year of construction: approx. 1990 Digital Display: 3-Axis (NEW) Max. turning diameter over bed: approx. Ø 320 mm Max. turning diameter via support: approx. Ø 198 mm Max. turning length: approx. 650 mm Bar passage: approx. Ø 40 mm Spindle speed: 96 – 2500 rpm Spindle nose: A 2 - 5 Drive power: approx. 2.2 kW Threading: Metric, Inch, DP, Module Tailstock: MK 3 Dimensions (LxWxH): approx. 1700 x 1000 x 1700 mm Weight: approx. 650 kg ✅ Accessories 3-jaw chuck 160 mm (NEW) Quick-change steel holder + 1 insert Electric Lining Guard (NEW) Work light (NEW) Complete machine documentation Emergency stop Various tension wrenches Coolant Setup L+Z Spindle  ...

Reduction and transfer case for conical twin screw extruder Cincinnati Titan 58 Manufacturer: Eisenbeiss on behalf of Cincinnati Extrusiontechnik General overhaul included: • Checking the sprockets for damage with a special camera • New sealing of the drive and output shaft • New shaft bearing • New oil filling • Repainting Condition: overhauled, fully functional

Control screening machine Tripette & Renaud model 21 M2 Conical strainer basket 300-360/ 800 Power 3 kw V-belt drive Wire covering MW 1.2 Outlet funnel is included Good condition

Fully automatic capping machine PMFS100. High-precision mechanical design for seamless bottle positioning. Sliding cylinder modules for cap tightening. Intelligent control system with touchscreen. Electrically and pneumatically driven. Surfaces made of stainless steel or food-grade plastics (GMP-compliant). Suitable for mass production. Production capacity: 120 bottles/min, compressed air: 0.6kg/cm², air consumption: 20m³/h. Inspection possible by prior arrangement.

Circular shears from Universal - Grooves - Scoring - Cutting Working width: 2,600 mm including automatic destacker (width: 2,500 mm)

3 controllers + 4 industrial screens, Product control + …, Electronics GmbH, used Used! - comes from a spare parts warehouse of a certified production facility, - The parts were removed from die casting machines. Measuring system controls: 3 used measuring system controls from company Electronics, Type: Product control S/N: 0513 4 pcs used industrial screens for the measuring systems At a special price of €500 for all 7 devices without warranty

Key data: 230 mm, 460 mm, 25 U/min

Optimum D460x1500 lathe – fully functional Description: For sale is a used Optimum lathe D460x1500, built in 2006/01. The machine is fully functional and ready for immediate use in the workshop and production. It is ideal for turning medium-sized metal and steel parts. Technical data: Manufacturer: Optimum Model No.: D460x1500 Year of construction: 2006/01 Circumferential diameter over bed: 460–465 mm Circumferential diameter over upper slide: 270 mm Circumferential diameter without bed bridge: 690 mm Center width: 1500 mm Tip height: 230 mm Bed width: 300 mm Spindle bore: 58 mm Spindle cone: MK 6 Spindle mount: Camlock ASA D1–6 Speed range: 25 – 2,000 rpm⁻¹ Longitudinal feed: 0.031 – 1.7 mm/rev Transverse feed: 0.014 – 0.784 mm/rev Thread metric: 0.1 – 14 mm Thread imperial: 1/2 – 2 gears/inch Motor power ...

Technical data: - Operating hours 4248 h - Load hours 1978 h - Operating pressure 10 bar - Delivery rate 3.34 m³/min - Drive 400 V / 22 kW - Motor speed 3000 rpm - Space requirement approx. W 1300 x H 1250 x D 800 mm - Weight approx. 490 kg

Technical data: - Operating hours 20256 h - Operating pressure 13 bar - Delivery rate 4.09 m³/min - Drive 400 V / 26 kW - Motor speed 3000 rpm - Space requirement approx. W 900 x H 1750 x D 900 mm - Weight approx. 490 kg

Year of manufacture 1980s/90s Technical data: Tip height: 185 mm Center width: 750 mm Turning diameter over bed: 370 mm Spindle bore: 36 mm Bed width: 250 mm Speed range: 38 - 1600 rpm Tailstock mount: MK 3 Quill stroke: 110 mm Dimensions (WxDxH), approx.: 1950 x 900 x 1200 mm Weight, approx.: 800 kg Equipment: - 3-jaw lathe chuck, brand: Röhm, ø 200 mm - Quick-change holder with 4 inserts - Bed stop - Chip tray

Scale Soehnle/Conveyor Technology Scale, motorized Manufacturer: Soehnle/ Overbeck Condition: Good (used) Model No.: SNR 215158 Total length: approx. 850 mm Total width: approx. 850 mm Conveyor width: approx. 440 mm Roller spacing/centre distance: approx. 75 mm Including roller drive Overbeck SEW motor included Feet included (height adjustable) Scales incl. Overbeck roller conveyor The conveyor technology ran until dismantling. Condition: fully functional, with signs of wear Ideal for fast material transport Internal Article Number: 2026012702 Expertly dismantled and packed Thanks to the excellent workmanship of the conveyor technology, your material glides smoothly to its destination, even under high loads. Tailor-made solutions for your intralogistics We are your competent partner for roller conveyors, belt conveyors, inclined conveyors or telescopes for loa ...

A Dinnissen centrifugal screening machine for classifying screening of bulk materials is available. Screening area: 2.2m², screen basket division: 5, inlet height: 900mm, screen basket fineness: 250µm, min. screening chamber operating pressure: 0.5bar. Machine dimensions X/Y/Z: approx. 2200mm/1050mm/1650mm, weight: approx. 1050kg. Without control cabinet. Documentation available. An on site inspection is possible. Image is an example.

Type: ASP600HDI Serial number: 23401215 Year of construction: 2004 Belt width: 600 mm Belt speed: 1.2 - 12 m/min Power: 3 x 400V, 50Hz, 3kW Dimensions: 2300 x 900 x 1550 mm Weight: 600 kg

This KUHNE KS45-24D compounding extruder was manufactured in 2006. Ideal for processing a variety of materials, it offers robust construction and reliable performance. Consider the opportunity to buy this KUHNE KS45-24D compounding extruder. Contact us for more information.

This LEISTRITZ ZSE60MAXX-48D was manufactured in 2012. A co-rotating twin-screw extruder, its designed for high-performance compounding of advanced polymer materials, including biodegradable polymers. Adaptable to various extrusion processes, its ideal for bioplastics, masterbatch production, or specialty compounding. Contact us for more information about this machine.

Key data: 20 mm, 25

single-screw laboratory extruder Collin E 20 M Output capacity: max. 5 kg/h (depending on material and processing conditions) Screw diameter: 20 mm, L/D = 25 Screw suitable for processing PE/PP (condition: excellent) Heating capacity cylinder: up to 300 C incl. mass pressure and temperature sensor Incl. motorized lifting device for the height adjustment of the processing unit incl. material funnel incl. clamping flange for nozzle attachment Total connected load: 17 kW Dimensions (L x W x H): 1,450 x 800 x 1,900 mm Weight: 300 kg Note: including complete documentation Condition: used, function-tested

1.0 PCS screw compressor system consisting of the The following components: 1.0 pcs Screw Compressor, Manufacturer: Almig, Type: Belt Drive 15 , Year of manufacture: 2013, Operating pressure: 10 bar, power 15 KW 1.0 pcs. Compressed air dryer Manufacturer: Prematic 1.0 pcs pressure vessel 1.0 Sr. Oil Separator

Control screening machine HOHLWSM-X 16/27 Normal steel painted Plaster lid on the screw tube with safety switch Control lid with safety switch Drive 1.1 kw ATEX 2 x wire screen with support basket (1 x 5.0 mm, 1 x 3.0 mm) Outlet Crossing NW 100 Top condition

Key data: 75 mm, 30

Single Screw Extruder Cincinnati TALOS 75-30G Output capacity: max. 450 kg/h (depending on material and processing conditions) Screw diameter: 75 mm, L/D = 30 Screw geometry for processing HDPE/PP 11 x Tool Zones incl. TC Type J ITIB 3-pin Thermal Probe incl. mass temperature and pressure sensor Interface for succession via CAN Open Bus Machine control Cincinnati EXcXP-touch Drive power main motor: 125 kW Total connected load: 178 kW Machine weight: 2,200 kg Remark: incl. spare engine (used) without material hopper Condition: used, function tested

Manufacturer: KAESER Model: BSD 72 SFC Year of Manufacture: 2012 Machine type: Screw Compressor Rated Power: 37.0 kW Motor Speed: 2960 1/min Max. Operating Pressure: 8.5 bar Ambient Temperature: 3 degrees C / 45 degrees C

Sartorius Combics 3 platform scale Stainless, platform scale with ramp, weigh range 1Kg to 300Kgs, platform 1000mm x 1000mm, 1Ph

Key data: 2 , 10

New AGRE Alup screw compressor with filter unit (technically oil-free), for the operation of milking robots. IMMEDIATELY AVAILABLE from the Hengsberg warehouse in Styria! We are also happy to take care of the delivery and commissioning of the compressor and ongoing maintenance of existing compressors of the brands AGRE, Alup and Atlas Copco. Drive: Efficient IE3 motor with belt drive Control: Infologic² Connect Refrigeration dryer and 270 litre container integrated Includes filtration for technically oil-free operation Performance data Volume flow at operating pressure 9.5 bar: 0.29 m³/min Operating pressure min. / max.: 5.5 / 10.0 bar Total power consumption at 9.5 bar / full load: 3.7 kW Rated power motor: 2.2 kW Pressure dew point refrigeration dryer : approx. +3 °C Dimensions and weight Length x width x height 1540 x 600 x 1350 mm Weight 205 kg Compressed a ...

Key data: 5 , 10

Oil lubricated screw compressor Cooling: Air-cooled design Drive: Efficient IE3 motor, belt drive Control: Speed-controlled with frequency converter Control: Infologic² Connect Refrigeration Dryer: Integrated Filtration optionally available Performance data Volume flow at operating pressure 7.0 bar 0.33 - 0.75 m³/min Operating pressure min. / max. 4.0 / 10.0 bar Total power consumption at 9.5 bar / full load 7.7 kW Rated power motor; IP55 5.5 kW Oil volume 3.2 lt Pressure dew point refrigeration dryer approx. +3 °C Installation data Ambient conditions min. / max. 1 / 46 °C Cooling air demand 1140 m³/h Free fan pressure 30 Pa Sound level 61 dB(A) Voltage / PH / Frequency 400 / 3 / 50 V / Ph / Hz Refrigeration dryer power (230V/50Hz) 0.19 kW Dimensions and weight Length x width x height 1540 x 600 x 1375 mm Weight 230 kg Compressed air outlet 1/2 "  ...