sc 17 used for sale

Size: 2.200 x 6.800 (5.750)mm - Year of Manufacture: 2002 - 2 Decks - Included: 18 kW Electrical motor, Cardan shaft and Springs.

Size: 1.800 x 4.000mm - Year of Manufacture: 1998 - With Electrical motor (11 kW/6), Cardan shaft and springs - Will be overhauled, sandblasted and painted.

OVERHAULED - Size: 1.400 x 3.000 mm - With Electrical motor, Cardan shaft and Spring elements.

OVERHAULED - Size: 1.600 x 2.000 mm - With Electrical motor and springs.

Size: 2.000 x 5.460mm. - With part of frame, E.Motor and Rubber springs

Size: 1.400 x 2.400 mm - Included: Electrical Motor (4 kW / 1.060 RPM) and springs - Will be overhauled, sandblasted and painted.

OVERHAULED - Size: 1.500 x 2.000 mm - Included: Electrical motor and springs

Size: 1.600 x 5.500 mm - Decks: 2 - Included Electrical motor and springs - Will be overhauled, sandblasted and painted

Size: 1.500 x 4.500 mm - Decks: 4 - Included: Electrical motor and springs (Frame not included)

Deck size: 2.000 x 6.300mm. - Double decks - With Frame, Motor Console, Cardan-shaft and Rubber springs - Can be sandblasted and painted

Widthness: 2.000 mm - 6 Decks - Year of Manufacture: 2001 - With 2 Pcs. Unbalance exciters, 15 kW / 970 RPM Electrical Motor and springs.

Widthness: 1.500 mm - 6 Decks - 2 Pcs. Unbalance Motors (3,6 kW / 1.430 RPM) - With frame and springs

Screen chute without drive for sandblasting systems, FUF, Vibra Technik, mint condition -60% Special price If you have a VAT number, we will gladly issue you an invoice without VAT. As good as new! The part was purchased from a company's spare parts warehouse, has only minor signs of storage, has never been used and is completely new. - Vibra sieve chute without drive with MW5 sieve insert and GP5 silent block - 1150 x 600 mm approx. 100 kg A sieve chute is a component used in sandblasting systems to sieve blasting media. It separates larger particles from the finer grain size before the blasting media is reused and is part of the recovery system, where blasting media is collected, sieved and returned to the cycle after blasting. 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the ...

Offer 25432 Specifications: - Turning diameter 320 mm - Center width 750 mm - Largest turn – Ø over bed 550 mm - via flat slide 175 mm - Spindle bore 32 mm - Spindle holder - Pick-up cone of the tailstock quill MK 3 - Quill stroke 180 mm - 18 spindle speeds 85 - 2000 rpm - Feeds longitudinal + flat - Metric thread pitches -Thread - Module thread - Diametrical Pitsch thread -Arbor - Cheek chuck -Lunette - Drive 400 V / 2.2 kW - Space requirement approx. W 2100 x D 750 x H 1300 mm - Weight approx. 750 kg

Manufacturer: Optimum Year of construction: 2024 Condition: as good as new, workshop tested Delivery time: immediately available Specifications Tip height: 165 mm Center width: 830 mm Circumferential diameter over bed: 330 mm Circumferential diameter over face slide: 208 mm Swivel length in the bed bridge: 430 mm Speed ranges: 16 steps, 70–2000 rpm⁻¹ Drive motor: 1.5 kW, 400 V, 50 Hz Spindle holder: Camlock DIN ISO 702-2 No.4 Spindle bore: 38 mm Spindle cone: MK5 Tailstock mount: MK3, quill stroke 110 mm Weight: approx. 512 kg Machine dimensions (LxWxH): 1685 × 745 × 1590 mm Gradients and feed Metric: 0.4-7 mm/rev (26 pitches) Inches: 56-4 Gg/1" (34 pitches) Longitudinal feed: 0.052–1.392 mm/rev (32 feeds) Face feed: 0.014–0.38 mm/rev (32 feeds) Accessories: Fixed bezel (Ø 6–50 mm) Rotating bezel (Ø 8–3 ...

Weiler Commodor – lead and pull spindle lathe (partially overhauled, built approx. 1990) Condition: Partially overhauled, very good general condition Year of construction: approx. 1990 Manufacturer: Weiler Model No.: Commodor Machine Type: Lead and Pull Spindle Lathe Technical data (approx. information): Max. turning diameter over bed: 380 mm Max. turning diameter over support: 190 mm Max. turning length: 1000 mm Bar Passage: 56 mm Speed range: 25 – 2000 rpm Spindle Nose: A2-6 Drive power: 4.0 kW Tailstock: MK4 Automatic longitudinal and flat feeds: 0.011 – 0.80 mm/rev Thread ranges: Metric: 0.3 – 10 mm Inch: 80 – 2 3/4 G/" Diametrically Pitch: 80 – 5.5 Dp Module: 0.2 – 5 Dimensions (L x W x H): 2200 × 1200 × 1800 mm Weight: approx. 1500 kg ⚙️ Equipment & Accessories: 3-Axis Digital Display SINO (New)  ...

Work platform self-propelled articulated work platform with boom PB Type: S171-12ES Year of Make: 2013 Load capacity 400 kg Platform dimensions approx. 2.79 x 1.17 m Platform extension approx. 100 cm Transport dimensions approx. 3.28 x 1.22 x 3.28 m (height railing folded down: 2.32m) Weight approx. 5120 Kg Working height approx. 17.1 m Platform height approx. 15.1 m Movable up to 17.1 m working height (indoor use) Self-leveling support Shipping no problem. Location of the machine is 94244 Teisnach ( See pictures ACTUAL - condition) Prior viewing is expressly desired, simply leave phone number by mail, then I will get back to you for a viewing appointment. Subject to prior sale, All information without guarantee. The machines can be picked up by yourself or shipped by freight forwarder at the expense of the buyer. Loading or packaging c ...

Off-road work platform Scissor lift with automatic tilt compensation UPRIGHT Type: SL26SL Year of Make: 2008 Load capacity 680 kg Platform dimensions approx. 3.66 x 1.72 m Platform extension approx. 80 cm Transport dimensions approx. 3.79 x 2.13 x 2.6 m (height railing folded down: approx. 1.9m) Weight approx. 3150 kg Working height approx. 9.93 m Platform height approx. 7.93 m Self-leveling tilt compensation The machine works, but has not yet been further technically and visually refurbished. Therefore, here is the special price in advance in the actual condition. Shipping no problem. Location of the machine is 94244 Teisnach ( See pictures ACTUAL - condition) Prior viewing is expressly desired, simply leave phone number by mail, then I will get back to you for a viewing appointment. Subject to prior sale, All information without guarantee ...

in nieuwstaat 2 Atlas Copco Freqentiegeregelde lage druk compressoren Max 4 Bar max 93 Kw 200 bedrijfsuren

nieuwe schroefcompressor 4 Kw op ketel met droger

TOS Galanta SUIL 40A – Lead and Pull Spindle Lathe For sale is a well-preserved and mechanically overhauled 2009 TOS Galanta SUIL 40A lead and pull spindle lathe, built in 1998. Specifications Manufacturer: TOS Model: Galanta SUIL 40A Machine number: 0219 Year of manufacture: 1998 (mechanically overhauled 2009) Dimensions: approx. 2.2 m × 1.1 m × 1.75 m Weight: 1620 kg Main drive: 5.5 kW Spindle speed (max.): 3150 rpm Spindle bore: 50.2 mm Center spacing: 1000 mm Center height: 200 mm Turning diameter over bed: 400 mm Condition: ready for use (used) Accessories Three-jaw chuck Tailstock Lunette Coolant Setup Interchangeable Wheel Set Operating instructions (German) The machine is fully functional. Viewing possible by appointment

Manufacturer: Zentner Systems GmbH Model: Soltec ST 100 Year of Make: 2006 Serial number: 0505 / 06 Operating voltage: 3 × 400 V Mains frequency: 50 Hz Operating power: 3 kW Operating pressure (air): 6.0 bar Design: Closed stainless steel screen washing cabin Application: Automatic cleaning of screen printing frames Particularities: – EX signs available – Integrated exhaust air / exhaust system – Compact design with its own control cabinet Location: Schierling Viewing possible by appointment.

Key data: 22 mm, 60

Single screw extruder 60 with renewed PMA control in 2010 - was replaced by double screw 5 years ago. Works after oil and belt change

feed pressure: 8,5 bar liter capacity: . l total power requirement: 454 kW weight of the machine ca.: t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ALMIG Combi 15-10 rotary screw air compressor YOM 2012. Never used. Motor speed 3000 rpm Motor power 15 kW Volume flow m3/min- 1.84 Volume m3/hour- 110 Max. pressure 10 Bar. Air Receiver Capacity 500L

Digital Center height 150 mm Circulation over bed 300 mm Center width 1000 mm 3-jaw chuck, Arbor Chip protection Chip tray

Motor power: 45 kW Nominal flow rate: 7.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1500x1000x1265 mm Estimated weight: about 700 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-4

A twin screw extruder is offered. Drive: ASEA electric motor type ACA 200-6L, 50.5kW, 1460rpm. Inspection possible by prior arrangement.

Motor power: 11 kW Nominal flow rate: 1.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-2

A screw compressor is offered. Maximum pressure 10bar, volume flow approx. 2020l/min (2.02m3/min) with separate compressed air tank, galvanized. Viewing possible by appointment.

Motor power: 7.5 kW Nominal flow rate: 1.0 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 900x625x860 mm Estimated weight: about 200 Kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-1

Motor power: 15 kW Nominal flow rate: 1.7 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-3

Offered are 2 screw compressors with the following features per unit: Power: 15kW, pressure: 10bar, volume flow: 1950l/min (1.95m3/min), speed: 2930rpm, including sound enclosure, 1) year of construction 1989, operating hours: approx. 38100h, 2) year of construction 1986, operating hours: approx. 10600h. Inspection possible by appointment.

✨ Grab it now †your top scaffold deal! ✨ We’ve got a 100 m² facade scaffold with a system width of 1.09 m , ready to use right away. The package includes a walk-through frame, adjustable base jacks, and everything you need for your next project. 🏗️ This set is based on the proven Layher Blitz frame scaffold and combines durable materials, high stability, and easy handling . The steel or aluminum decks are particularly long-lasting, and the integrated walk-throughs with ladders make working comfortable and safe. Thanks to the standardized 2.57 m frame length , the scaffold can be easily expanded and is fully compatible with all original components. 💪 The plug-in system allows for quick assembly and disassembly, saving valuable time on the construction site. At the same time, the sturdy design ensures you can work safely ...

🚨 Be quick †limited stock! We offer top Layher Blitz scaffold packages †100  m ² of fa çade scaffolding , system width 1.09  m . Includes access deck with ladder, base jacks, and everything you need to get started. The complete set for your next façade scaffold project †ready to use and available while supplies last . ⚡   This package is based on the proven Layher Blitz frame scaffold system with a 1.09 m system width. It includes heavy-duty steel or aluminium decks, access decks with integrated ladders, diagonal braces for structural stability, and base jacks for safe height adjustment †all original Layher components .   Thanks to the standardized 2.57 m bay length, the system is easy to expand and fully compatible with other Layher Blitz parts †ideal for professionals who want to work quickly ...

Two identical compressors with integrated refrigerated dryer are offered. Pressure dew point: +3°C, rated power: 30kW, delivery rate (FAD): 5.31m³/min at 8bar, 4.77m³/min at 10bar, 3.86m³/min at 13bar, control: Boge Autotronic, fully automatic operation. Inspection is possible by arrangement.

BANDERA TWIN SCREW PVC PIPES EXTRUDER, for pipes with min/max diam.40/200 mm., extruder with n.2 parallel counter-rotating screws Ø 90 mm, Throghput rate 400 kg/hr, missing of screenchamger (can be added separately), n.2 dies available 40 to 125 mm + 125 to 200 mm., Tooling from 40-200 mm (available diam. 100 mm for O-Ring), Bandera 6 mt.long vacuum calibration tank, IPM haul off unit, IPM saw, IPM belling unit, constructed in 1998, totally refurbished in 2006 by Plasco, machine now disconnected, offered RECONDITIONED., availability: immediate, working width: 40-200 mm Ø, capacity: 400 kg/h, conditions: disconnected, type: pipes extrusion line

Please refer to Fig. 2 for technical data

Vacuum extrusion press 'UNIVERSA' PZG 40-40a with 400 mm Ø and 18.5 kW drive (expandable up to 55 kW). Maximum pressing pressure: 30 bar. Extruder incl. PZSVG 35a pre-press with 15 kW drive. Includes base frame with motor clamping device. In regularly serviced condition; last revision in 2022. Previous use: Production of ceramic roof tiles. Available for an extra charge: vacuum generator and various mouthpieces.

Please refer to Fig. 2 for technical data

Please refer to Fig. 2 for technical data

We stock numerous lengths of this type, e.g. 220 / 270 / 320 / 370 / 420 / 470 / 520 / 570 / 620 / 670 / 720 / 770 / 820 / 870 / 920 / 970 / 1020 / 1120 mm and others. All scales are thoroughly cleaned and checked for perfect function before delivery. The prices are – depending on the length – between 290 and 370 EUR. Please ask us for the exact prices. Please note that these are exchange prices.

We can offer Krauss maffei extruder,moder ZE90A, manufactured in 2013, main motor power 884kw, large output, installed and used, auxiliary equipments available, serious buyer contact us.

We can offer Krauss maffei extruder,moder ZE90A, manufactured in 2013, main motor power 884kw, large output, installed and used, auxiliary equipments available, serious buyer contact us.

Manufacturer: ESC Model: ESC-AT-60PD Type of Machine : Screen Printing Machine Semi-automatic, universal, digitally controlled precision screen printing machine for flexible and rigid materials up to 200 mm material thickness STANDARD EQUIPMENT/FEATURES - Programmable PLC control system - User-friendly operation via touch screen - High-quality linear guides for smooth, low-noise motion - Vertical, motor-driven screen frame lifting with synchronized stripping motion - Precision print head with pneumatic lift for screen change and cleaning - Digital input of desired print parameters: - Speed for print and flood squeegee - Print height - Print stroke length - Neutral position for print and flood squeegee - Single-function control for setup operation - Single-cycle operation via foot switch and automatic cycle mode - Extremely short setup times without the need for tools - Pneumatic scr ...

L+Z Lathe WEILER Praktikant 160 – Partially Overhauled Machine in very good used condition – delivery on order, delivery time by arrangement! ✅ Technical data Year of construction: approx. 1990 Digital Display: 3-Axis (NEW) Max. turning diameter over bed: approx. Ø 320 mm Max. turning diameter via support: approx. Ø 198 mm Max. turning length: approx. 650 mm Bar passage: approx. Ø 40 mm Spindle speed: 96 – 2500 rpm Spindle nose: A 2 - 5 Drive power: approx. 2.2 kW Threading: Metric, Inch, DP, Module Tailstock: MK 3 Dimensions (LxWxH): approx. 1700 x 1000 x 1700 mm Weight: approx. 650 kg ✅ Accessories 3-jaw chuck 160 mm (NEW) Quick-change steel holder + 1 insert Electric Lining Guard (NEW) Work light (NEW) Complete machine documentation Emergency stop Various tension wrenches Coolant Setup L+Z Spindle  ...

Reduction and transfer case for conical twin screw extruder Cincinnati Titan 58 Manufacturer: Eisenbeiss on behalf of Cincinnati Extrusiontechnik General overhaul included: • Checking the sprockets for damage with a special camera • New sealing of the drive and output shaft • New shaft bearing • New oil filling • Repainting Condition: overhauled, fully functional

Control screening machine Tripette & Renaud model 21 M2 Conical strainer basket 300-360/ 800 Power 3 kw V-belt drive Wire covering MW 1.2 Outlet funnel is included Good condition

Fully automatic capping machine PMFS100. High-precision mechanical design for seamless bottle positioning. Sliding cylinder modules for cap tightening. Intelligent control system with touchscreen. Electrically and pneumatically driven. Surfaces made of stainless steel or food-grade plastics (GMP-compliant). Suitable for mass production. Production capacity: 120 bottles/min, compressed air: 0.6kg/cm², air consumption: 20m³/h. Inspection possible by prior arrangement.

3 controllers + 4 industrial screens, Product control + …, Electronics GmbH, used Used! - comes from a spare parts warehouse of a certified production facility, - The parts were removed from die casting machines. Measuring system controls: 3 used measuring system controls from company Electronics, Type: Product control S/N: 0513 4 pcs used industrial screens for the measuring systems At a special price of €500 for all 7 devices without warranty