130,804 used machines on RESALE, but how to find them? Machine Search
Lot 592 500L steam jacketed hemispherical scrape surface vessel, bottom central discharge, half moon lid, agitator (six sets of removable propellers along shaft)
Showroom machine Firing furnace powder furnace divisible Romer SLP-90 O D + t convection baking oven Powder furnace new SLS - 90 / O D + t Transit oven divisible Memorized 1400 wide x 2000 height x 6500 depth Dimensions 1920 wide x 2810 height x 6800 depth Electric power supply Rated power 90 kW Voltage 380V Frequency 50-60 Hz Door type: 2 doors on either side - passage oven Anti-ex Castle Warm-up time 15-30 min. (180 ° C) Uniformity & lt; ± 3 ° C, if 180 ° C Max & lt; ± 3 ° C Temperature of 230 ° C Max Transport: selectable Air circulation fan Heaters removable roof heating panels Vertical circulation Fan mounted radially on removable panels Door double two doors on two sides (Durschlaufofen) Divisible Motor 1,1 kW 6480 L capacity Warranty 12 months
Demonstration device. Powder coating plant mini - for beginners The spark / ROMER® powder coating plant mini - consists of: SLS-9 small powder furnace (Indoor: 1200x1400x1200mm - without transport system) Powder booth KPZ-2 p Powder hand plant AP 400 Shipping costs will be calculated individually. (also, pickup) Payment conditions: 30% deposit and the balance of 70% with notification of readiness for dispatch.
Beer tank, single-walled, isolated with fittings Manufacturer: Wilhelm Schmidding Type: transport container Year of construction: 1977 Capacity: 22,500 litres Pressure: 3 bar Material: 1.4541 Temperature: 20 ° C Dimensions: Diameter: 1,750 mm Length: 9,850 mm Container has been cleaned already. In very good condition!
MAK M20 Spares for sale. 1.Reusable Cyl Heads Bare-Pressure Tested Free From Crack:8-10 2.Piston With Groove With in Limit:8-10 3.Con Rod-Free From Crack, Wear Within Limit:8-10 4.Fuel Pump-Good Condition:8-10 5.Reusable Liners Wear Below 0.20mm-Free From Crack, Welding or any Damages:8-10 6.L O Filter-Good Condition:2 7.Water Pump-Good Condition:1 8.Lube oil Pump-Good Condition:1 9.Turbo Charger K54-Good Condition:2 10.STD Condition 6M20 Crankshaft, Within Std Limits, no Crack, no Ovality , Hardness Within Limits:1 11.Cam Shaft 6M20-Good Condition:2 12.Woodward UG-8 - Good Condition:2 13.6M20 Engine Block-Good Condition:1 14.Cam Shaft Gear & Crankshaft Gear-Good Condition:2 15.FLY Wheel-Good Condition 6M20:1 16.After Cooler-Good Condition 6M20:1
Laminating rollers Billhöfer Model 102 & 104 series and maybe others Year 2005 Qty available 1 set Available Direct
Technical data: Table load 40 to. Table diameter 3,330 mm Speed 0.01 0.2 U/Min. Voltage 400 V / 50 Hz Power 6 KW To the weight of the table 15. Dimensions L x W x H 5,600 x 2500 x 3,200 mm
Complete Shavereinheit with handpiece, foot switch, 2 sterilization box for the Shaverpaltes. 46 Shaverplates Fully functional. Unused, mint condition, used only for demonstration purposes.
System: piston diaphragm pump Manufacturer: Emmerich Type: SP521 2075 Machine number: 0275 Year of construction: 1977 Performance: 5m 3 with 16 bar Pressure: 16 bar Engine: BBC, 14.9 kW, 50 Hz Inlet connection: DN 50 Durckseite connection: DN 50 Dimensions: approx. 1600 mm L
Cooling tray type KW 1000-200-200 self-sufficient for strand cooling in the production of granules or filaments. - a mobile and height-adjustable base frame made of welded steel raw, left machine version, painted - Frame-height adjustment of the top edge of the water bath from 900 mm to 1050 mm - a VA cooling tray 1000x200x200mm - 2 pieces adjustable and mounted strand holder - clamped to water edge - 1 piece wiper bled for partial strand drying - 1 piece of adjustable tub plug for filling height adjustment - 1 piece of VA water tank (reservoir) as service water tank - 1 piece of bacon water pressure pump to supply the cooling tank with sufficient cooling water from the water tank - 1 piece of direct 1/2" fresh water connection via float switch and solenoid valve for connection to the customer's side Fresh water network - Tub overflow - drain pipe DN50 for connection to ...
FRICTION BELT FOR SCREW PRESS DIRECT FROM THE MANUFACTURER! Description: -Chrome leather friction belt for screw presses, riveted, new! -Dimensions: 530 mm i. diameter x 50 mm high x 18 mm thick ON request make we the friction belts regarding to your sizes! For all machine types like SMS Hasenclever Berrenberg, Schuler, Weingarten, Vaccari, via, Mecolpress, Osterwalder... We deliver worldwide! We confirm best service and short delivery times.
Technical data: Drive motors/ motors Number: 6 pieces available Manufacturer: SEW Eurodrive Condition: used, not used, Power: 50Hz/r/min 1440/140 KW 0.75 S1 Tailor-made solutions for your intralogistics We are your competent contact for roller conveyors, belt tracks, inclined belts or telescopes for loading and unloading your goods! We will be happy to prepare your individual offer or advise you on the conception or assembly questions. Just let us know your needs and local conditions. Take advantage of our many years of experience and our excellent network of professionals. We have already successfully implemented projects for companies in a wide .B: logistics, pharmaceutical industry, crafts or the electronics industry. Together, we will develop ways to optimize your flow and material flow cost-effectively and sustainably. We can offer you even fully ...
Shredder, industrial shredder, 2 wave star breakers, glass shredder, rotor scissors, star mill, garbage shredder, two-shaft shredder, two-shaft shredder, shredder with filler for wheel loader used The shredder can also be used as a single position. Manufacturer: SANT'ANDREA NOVARA Type: G30/1570 Built in 2003 Speed of the fast wave: 17.7 rpm Speed of the slow wave 9.3 rpm Turning monent. 11875 Nm Engine VEM 22 kW 400/690 V Dimensions Shredder: approx. 2500 x 1000 x height approx. 400 mm with motor 1500 mm Dimensions of cutting unit approx. 1600 x 810 mm Throw-in height approx. 4.6 m Throw-in funnel approx. 3 x 2 m the drop-in funnel is closed by a percular upward opening slider approx. 2.5 x 1.5 m. Total dimensions of the steel construction: approx. 3 x 2 x 8 m In the shredder, used glass was broken for a foam glass bulking system. Basically, other brittle material ...
Type: Ruhle SR2 Loading sections (L x W x H): 500x120x200 mm Cutting length: 1,0 – 30,0 mm Saw blades 1 set Capacity: up to 1800 kg/hour Electric power: 3.5 kW Machine dimension in cm: Width: 70 cm Lenght: 150 cm Height: 125 cm Delivery time: 10 working days after advanced payment
Dosing pump, diaphragm dosing pump unused Seko 3 head diaphragm dosing pump Stainless steel pump housing Built: 2016 Engine 7.5 kW 380/660 V Pumps Temperature range: -20/30 °C Type 1T10N12FB Capacity: max 11.4 l/h Pressure max 60 barg Speed. max 117 SPM Type: 1T30N12FB Capacity: max 108 l/h Pressure max 60 barg Speed. max 117 SPM Type 1T50N32FB Capacity: max 598 l/h Pressure max 60 barg Speed. max 117 SPM Actuators: Seko SRE.40AA2000 Rotork R-250 with pulsation damper and accessories as shown in photos Shipping dimensions: approx. 1800 x 1800 x 1800 mm Sale also possible in parts! The pump comes from a research facility and has never been used. Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.
Tip height: 130 mm Top width: 450 mm Rotational speed: approx. 55-3000 rpm Pneumatic clamping system Spindle nose: W 25 Div. W25 collets available Div. holder available BERGER LAHR axis motors Combitec EIP E-500 control Manual control available Coolant system available Machine lamp available Machine feet available Dimension (Lxwxh): approx. 1400 x 560 x 1230 mm Weight: approx. 550 kg The machine is located in a clean good condition!
Bread cutting machine Rösen & Robbert SPA 38 used sickle knife bread cutting machine with adjustable cutting width for breads up to 38cm long suitable for cutting and halving dark breads.Used bread cutting machine with cutting width adjustment of Rösen & Robbert type SPA 38.The machine runs with oiling, with sickle knife and digital steurung.Geignet to cut breads up to 38cm wide.Right compartment is inserted bread then the bread is inserted to the left. In the middle between left and right compartment, the knife rotates and cuts the bread in the desired thickness. The slices are pushed into the left compartment where they are just selected mid-disc holders. After cutting, mam can take out the slices and bag it on the tray. Easy operation and cleaning of the machine, little space requirement.Payment and shipping on request. Bread cutting machine R&R Type: SPA 38 for loaves up ...
Kilia Supreme Cut 200 ltr., 200 liters bowl cutter, bowl and bowl-cover stainless steel, year of manufacture 2011, hydraulic noise reduction cover, knife shaft brake electrically operated, separate stainless steel electric control cabinet, membrane keyboard, variable bowl speed, variable knife speed, variable mixing speed forwards and reverse, cleaning system, knife head with 6 knifes, hydraulic loading device for 200 liter bins, hydraulic unloader. You are very welcome to inspect and test the machine.
Inner gear pump, internal toothed displacement pump chemical pump used Inner gear pumps are used to convey liquids of any viscosity. Also with abrasive dusts but without solid stake. e.B. oils, soaps, bitumen, tar, chocolate, molasses, cocoa butter, fat, glucose VARISCO/ ROTOTEC Type: V 85-2 SPG Flow rate at 190 rpm max approx. 15 m3/h Connections Inside approx. 100 Flange outside approx. 230 mm Gearmotor Lenze GST09-2M VBR 112C41 7.5 kW 190 rpm 400 V IP55 Dimensions: approx. 1400 x 400 x 470 mm All items are checked for function before delivery, if technically possible! Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.
MAZAK laser cutting machine STX510 MKIII 4kW TOP CONDITION - LIKE NEW - ONLY 700 RUNNING HOURS year: 2012 refurbished, MAZAK lasercutting machine with 2500W table size: 3000mm x 1500mm machine dimension 2,9m x 7,3m chip conveyor LAN / USB connection automatic nozzle change fast piercing in heavy materials piercing sensor plasma sensor for stainless steel cutting burning sensor for mild stelle cutting full covered machine table FE: 22mm VA: 15mm ALMG: 10mm plastics possible to cut incl. software incl. exhauster option: warranty, setup, training option: fully automatic loading/unloading CELL system
SABROE PAC 163 HR-A Brand:SABROE Type:PAC 163 HR-A Stock number:M21-4474 Cooling capacity:1,437 kW Application:Cooling / Heating Refrigerant:R717 (NH3/Ammonia) Refrigerant Content:175 kg Voltage:400 Volts Power consumption:126 kW Motor power:160 kW Dimensions:5800 x 2660 x 2850 mm Weight:8,800 kg Year:2007 Number in stock:2 piece(s) Price:Quotation request Description: A very well maintained complete Sabroe water-cooled water chiller/heat pump. This water chiller is equipped with a frequency-controlled Sabroe SAB163HR compressor (up to 6,000 RPM), a Schorch 160 kW electric motor, an Alfa Lava evaporator and condenser, a complete control cabinet with a Vacon frequency controller and a Unisab II compressor/chiller controller. All necessary documentation is available. The stated capacity is for water +12/+7°C in/out. Visit also our website: used-refrigeration
Tip height 102 mm Top width 450 mm Leit.-/ spindle Collets W20 available Rotational speed: approx. 210 3000 rpm Reduction gear Links.-right rotation 2-stage drive L x W x H: CA. 1760 x 595 x 1230 mm Weight: approx. 650 kg
Meat processing equipment from a modern German butcher's shop for sale. The equipment consists of: • Seydelmann AD 114 automatic grinder • Kilia Meister Plus 50, 50 liters bowl cutter with variable knife speed • Vemag Robby Typ 136 vacuum filling machine with casing holding device • Poly Clip SCD 7095 clipping machine • Stiller can seaming machine DV 10 PS • Maja SA 85 S ice generator • Vakona ESK 125 Tumbler • Stein smoke house • scales, slicers, moulds, stainless steel tables If desired we can arrange worldwide delivery and send our German master butcher to instruct your staff on-site.
Schubert Press The platen size is 1390 mm (52”) x 2490 mm (98”) Electric heaters Make - Schubert Daylight – 305mm Floor standing Total number of rams: 16 Ram diameter: 2 ¾” Working pressure 3500 PSI The overall dimensions are length 3850mm x width 1500mm x height 2200mm Operational The condition of the hydraulics and pump unit along with ram seals is good Spare seals maybe possible (video link available on request)
Ladies and gentlemen, Here we offer a diesel trucks of the company Steinbock boss. Capacity: 14,000 kg Engine: Perkins Year of construction: 1992 Lifting height: 5000 mm When the stacker the Achschenkenlager is broken (the left rear wheel is wrong) Please call for more info, pictures or visits. 01773879144 With friendly greetings Subscriptions
Machine type: Forklift / Forklift Manufacturer: Still Model: R33 Built: between 75 and 80 Condition: ready for use (used) Price 7,450 net plus VAT Location Warstein, Germany Reference M-STI-0121 Description We offer you a used forklift from the manufacturer Still Technical data: Capacity: 6t Weight: approx. 9t Engine hours: 9986h Width: approx: 2250mm Fork length 2000mm Tine adjuster max 2100mm tine outside Lighting: Headlights and Rear Lights UVV Test: 01/2022 Mercedes Motor The forklift is in use with us, jumps immediately in any weather. No electronics. Operating hours may still vary, as the forklift is in use. Our offer is aimed at professionals who are covered in accordance with the Trade Code in accordance with Section 14 GewO. The offer is subject to change, intermediate sale reserved. Please provide your full contact details to receive a ...
Height 2130 Width 1410 mm Length 2130 mm Weight 1500 kg Capacity 1200 l Voltage Electrical: 400V 50Hz 3N Installed Power 9.1 kw Main material Stainlees Steel Load 1000 kg Mixing System Spiral With Paddles Product discharge Pneumatic dampers, front Mixer type Vacuum Mixer Shafts amount Double Shaft
Single column - eccentric press, STANKO, K 1430 A - 100t BJ. 1985 Tech. Condition very good, - pressure: 100 t -Projection: 320 mm -Stroke: 10-130 mm -Mounting height: 400 mm -Table size: 850 x 560 mm x 100 mm -Tappet adjustment: 100 mm -Stroke: 50-53 / per min. -Machine weight: 8800 kg -Dimensions (W x D x H): 1.60 x 1.85 x 2.9 m Camshaft gear ROSS/Herion Herion valve Auxiliary brake DESCH Lutex ZB 200 Two hand release -transverse eccentric shaft and pneumatically actuated clutch / brake Komi nation -suitable for inlays in two-hand operation -secure setting -Single stroke, continuous stroke MOT testing in 04/2016
Type Cutters Warranty 12 months Height 2350 Width 2200 mm Length 1910 mm Weight 4000 kg Voltage Electrical: 400V 50Hz 3N Installed Power 57.25 kw Main material Stainlees Steel Time of realisation in stock Cutter Type Bowl Cutter Cutter made of Stainless steel Bowl made of Stainless steel Bowl capacity 200 l Efficiency 100-140 kg/cycle Knives amount 6 pc. Knife shaft revolutions 900/1800/3600 rpm Bowl revolutions 7.5/10/15 rpm
A volume of depositors of the SIG type ZHG They can provide these depositors a SIG-GS or SIG-GRT We advise you gladly Phone: 0049 1718367957
used
Products For square, rectangular or round biscuits and baked goods suitable for roll separation Feed/System integration • For feeding pillow-pack and wrapping Machines • Presentation direct to portioner always with vibratory channels • Manual or automatic portioner infeed • Own drive Technical features • 4 to 12 channels
Panasonic AC Servo Motor Driver MSDA043A1A
Important and distinguishing design features of the RaptorX SL steel base gantry machine RaptorX-SL1200/S15 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large ...
CNC portal fraese and 3D engraving machine T-Rex 0712: equipment / product data of cnc-Fraesen Type High-Z/TRex series: Drive: 3 busiest brand stepper motors with 4.5 amperes. Pushing through long and up to 120mm high materials possible, as no belt drive is in the way at the end of the X axis! linear guides on all Y axes from HIWIN / THK ! Multiple ball-bearing ball thread spindles on all axes, brand make! Rapid speed max. approx. 17,000 mm/min working speed max. approx. 12,000 mm/min Technical platform X/Y: 0.005mm (1/10 step); Z: 0.0025mm reverse play maximum approx. +/- 10microns (0.010 mm) Point repeatability: approx. 0.01 mm clamping area of the groove plate / T-slot table: 1650 x 880 mm travel distances: X=1200mm; Y=700mm; Z= 130 mm contact contact sensors / reference switches / limit switches on all axes Double secured emergency release energy chains for cle ...
A used S O R A L U C E CNC driving stand milling and drilling center FS 16000 Built in 2000 MAIN TECHNICAL DATA: Travel: Longitudinal (X): mm 16000 Senkr. (Z): mm 1600 Cross (Y): mm 1500 Milling and drilling spindle: Tool holder: ISO 50, DIN 69871 Auto. Tool tension: clamping force 15000 N Tightening bolt: DIN 69872 Form B (BT50) Spindle speeds: Special speeds: rpm 20-3000 Feeds: Feed range: mm/min 2-5000 Rapids: X-axis: mm/min 12000 Y- and Z-axis mm/min 15000 The machine is equipped with: - HEIDENHAIN control TNC 426 M. - Operator's platform in the X-direction with sliding door and Viewing windows against chip flight and splashing water. - Operator's console swivels mounted on the stage. - Automatic thermal expansion compensation of the Milling sliders. - Automatically indexing milling head. This milling head enables the fully automatic m ...
CNC Router and 3D engraving machine T-Rex 0712: Equipment / product data CNC-milling machine type High-Z/TRex series: Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all axis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 17.000 mm/min Operating speed max. ca. 12.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table1650 x 880 mm Travels: X=1200mm; Y=700mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions ...
Rebuilt 2006 Cutting width-1.850 mm Feeding height 165 mm max Feeding depth 1,850 mm max Front table length 730 mm Table height 900 mm Equipment air table program cutting line indicator 2 knives pile lift PL 3 Jogger Vibro Info: computer modern cut control
Equipment / Product data of the CNC-Fraesen Type High-Z/TRex series / Type 1215 Drive: 3 busiest brand stepper motors with 4.5 amperes. Pushing through long and up to 120mm high materials possible, as no belt drive is in the way at the end of the X axis! linear guides on all axes of HIWIN / THK ! Multiple ball-bearing ball thread spindles on all axes, brand edging! speed speed max. 12,000 mm/min Working speed max. approx. 8,000 mm/min Technical platform X/Y: 0.005mm (1/10 step); Z: 0.0025mm reverse play maximum approx. +/- 10 microns (0.010 mm) Point repeatability: approx. 0.01 mm clamping area 1860 x 1340 mm travel distances: X=1500mm; Y=1200mm; Z= 130 mm contact contactno-point sensors / reference switches / limit switches on all axes Double-secured emergency trigger energy chains for clean cable Total mass with motors : LxWxH approx. 2180 x 1800 x 1420 mm Fra- Sc ...
3D CNC Router T-Rex 1215 / Technical Data : Equipment / product data CNC-milling machine type High-Z/TRex series: Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all exis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 12.000 mm/min Operating speed max. ca. 8.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table 1860 x 1340 mm Travels: X=1500mm; Y=1200mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions wi ...
Equiptment / product data CNC-milling machine type High-Z/TRex series / 1224 Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all axis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 12.000 mm/min Operating speed max. ca. 8.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table 2800 x 1340 mm Travels: X=2400mm; Y=1200mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions with engines : LxBxH ca. 3070 x 1800 x ...
Horizontal grinding optimum surface grinders ELB - 6375 ND - PLC Second-hand machine Surface grinders - horizontal ELB optimal 6375 ND - PLC Second-hand machine overhauled 2016 Surface grinders - horizontal ELB-SCHLIFF optimal 6375 ND - PLC Second-hand machine Grinding length: 600 mm Grinding width: 375 mm Workpiece height: 375 mm Table clamping surface: 600 x 350 mm Grinding wheel dimensions: 300 x 50 mm Grinding spindle motor: 4.7 kW Table speed: 2-30 m / min Grinding wheel speed: 1450 RPM Total power: 12kW Weight approximately: 3.5 t Space requirement approx.: 2.8 x 2.5 x 2.5 m Part overtaken 2016 + 12 months warranty, condition Control with touch screen new Paper machine Magnetic Chuck 600 x 350 Automatic table dressing with compensation 1 flange Items put up Installation / commissioning / transport
Sale of parts and assemblies ex large area mower Shibaura CM 364: Diesel engine 25 kw / hydrostatic transmission / axles / electric / cabin / wheels and more. no mower-deck.
new
RECON - pn. 0405 2497 - standard size, polished - flange diam. 178mm - incl. gearwheel and counterweights ---------------------------------------------------------------------- ------- Please note: we also have other various RECON parts of different manufacturers / types in stock. We are pleased to provide you with our current stock list. If you have any further questions do not hesitate to contact us
High-pressure cleaning device, high-pressure flusher, high-pressure built-in washer on hot-dip galvanized and painted high-quality steel frames with forklift flaps suitable for installation in company vehicles. PTC Salmon 60/200 and 75/150 similar but no evening & Fock, Karo, Leistikow, Müller, Rioned, Rockstroh, Rome, Rowo,... The following models are available: Salmon 60/200 | 60l/min. at 200bar | Engine: Vanguard 35 HP 26kW Salmon 75/150 | 75l/min. at 150bar | Engine: Vanguard 35 HP 26kW DIMENSIONS / WEIGHT: Dimensions without water tank LxWxH: approx. 700x1.250x1.200 mm Dimensions with 400l water tank LxWxH: approx. 1.300x1.250x1.200 mm Dimensions with 800l water tank LxWxH: approx. 2,000x1.250x1.200 mm Empty weight without water tank: approx. 300 kg Empty weight with 400l water tank: approx. 320 kg Empty weight with 800l water tank: approx. 350 kg HIGH-PRESSURE PUM ...
Stock# U2347-1 Used mixer by Buhler (CH) type SPM-50-HT with butterfly/tri-foil agitator for work on vacuum. Mixer has contact parts designed in non-corrosive steel. Mixing shaft has length about 1750 mm and is equipped with butterfly agitator, with three paddles and external diameter 1040 mm. Top cover is equipped with two pneumatic accutators and fits mixing pans with diameter 1100 mm. Cover can be rised up to 500 mm. Agitator is belt driven by el motor 45 kW, 1470 rpm, 380/660 V, 50 hz. Mixer is hydraulically risen about up to 90 cm. Machine is equipped with local control panel by Siemens with touchpad and electric cabinet. Machine is also equipped with hydraulicaly operated post for mixing can. Working pressure in mixing tank can reach 0.3 bar. Machine had been working on paints. Mixing pan is not included.
Centrifugal deposition Hydro Zyclone Liquid Particle Separator Hydro Cyclean HC5/HCH5 used Hydrocyclone Gravity-Water-Particle Separator Cyclone Water filter Water cleaner Watercleaner For separating heavier, larger particles in liquids or sludges. Was used to separate particles from washed-up pappier & cardboard solids. Price per pc3 3 x available Manufacturer: SULZER-ESCHER WYSS GmbH Type: HC5-TB5B.40 Y.O.M.: 1993 Main pipes dN400 1x Masch.Nr: 11835 (EQ.Nr 11GE01/1st stage) 1x Masch.Nr: 11837 (EQ.Nr 11GE01/1st stage) 1x Masch.Nr: 11836 (EQ.Nr 11GE01/1st stage) 1x available Manufacturer: SULZER-ESCHER WYSS GmbH Type: HC5-TB6B.48 Y.O.M.: 1993 Main pipes dN400 1x Masch.Nr: 11835 (EQ.Nr 11GE02/2nd stage) Cyclone & Distribution Material: Plastic Frame & Pipe Material: Stainless Steel Size Total approx.: 6200 x 1100 x 2800 mm Weight each approx.: 2.5 to T ...
maximum number of results exceeded
please refine your search
