rotogravure press used for sale

PRESS DESIGN   drive system: eccentric / crank PRESS FORCES   total force (nominal): 15 to PRESS TABLE   table surface (left-right): 360 mm   table surface (front-back): 260 mm SLIDE   stroke rate (max.): 165 /min SLIDE (MECHAN. PRESS)   slide adjustment: 40 mm   stroke min.: 7 mm   stroke max.: 60 mm TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 226 mm ELECTRICAL SPECIFICATIONS   total power consumption: 1.15 kW   mains voltage: 400 V DIMENSIONS / WEIGHTS   total weight approx.: 630 kg ATTACHMENTS (PRESSES)   safety guard / safety door: yes   2-hand engagement: yes   foot engagement: yes   European CE standards: yes

Inv. Num. : 948 Type: LVH 2500 Producer: ŽĎAS Created: 1961 Parameters: Depth: 1800 mm Width: 3450 mm Height above ground: 4650 mm Weight: 85 000 kg Voltage: 220 / 380 V Mains frequency: 50 Hz Workforce: 2500 t Number of strokes: 20/min Height of the lifts: 500 mm Minimum plunger distance from the table: 900 mm Maximum plunger distance from the table: 1400 mm Table surface: 1050 x 1400 mm Plunger area: 1050 x 1200mm

Müro A4/5000 block size press; good condition; cleaned and tested; Heat baffle; Stack increase; optionally with dryer. Block gluing machine Müro A4/5000; good condition; cleaned and checked; pile elevation; heating sheet; for option with heater.

blowers Müro block glue presses; Condition used; 2 pcs.; 1x old connector, 1x new connector; cleaned and checked for function. Heater Müro padding press; condition used; two pic.; one old connector, one with new connector; cleaned and checked on function.

Number Of Stations: 32 // Output (caps/min): 500

Number Of Stations: 24 // Output (caps/min): 600

used baler Manufacturer: ABBA Type: ACOMAT 400 H3A Year of Make: 2008 specifications: Press force: 45 t Drive power: 7.5 kW Throughput capacity: approx. 45 m³/h Filling opening: 1,150 x 850 mm Channel format: 790 x 730 mm (W x H) Bale size: 790 x 730 x length in mm (W x H x L) Binding: 3-fold horizontal Wire push-through: seen in the direction of pressing on the left side Machine dimensions: approx. 4,250 x 2,580 x 2,000 mm (L x W x H) Machine weight: approx. 3,600 kg

Air Pressure: 40 bar // Delivery Rate: 1630 m³/h

Air Pressure: 40 bar // Delivery Rate: 950 m³/h

A Reis spotting press for tool and mold making is available. Pressing force: 1000kN, clamping area: 1200mm/1500mm, installation height: 1575mm, max. mold weight: 10000kg, max. tilting plate load: 4000kg, ram stroke: 1450mm, return force: 400kN, hydraulic pressure: 190bar, pneumatic pressure: 5bar. Machine dimensions X/Y/Z: approx. 3200mm/4500mm/4100mm. Documentation available. On-site inspection possible.

Capacity 50 tons Stroke 750 mm Table size 1500x1000 mm

Offer 25374 Specifications: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Lifting speed 25 mm/sec. - Return 125 mm/min - Installation height approx. 1000 mm - Projection to the middle of the ram 380 mm - Pusher clamping surface 530 x 400 mm - Plunger clamping pin 40 mm - Table size 750 x 560 mm - Table hole / through hole in the table 200 mm - Table height above floor 720 mm - Oil filling quantity approx. 200 ltr - Drive 400 V / 11 kW - Space requirement approx. W 1150 x H 3250 x D 1850 mm - Weight approx. 4600 kg

Dough dividing and rounding machine ERIKA RECORD, type: Automatic machine No.3 -Refurbished- - For precise dividing and rounding of a wide variety of dough types - Fully automated workflow - Machine parts in oil bath (no lubrication necessary) - Machine head can be tilted, for better cleaning - Dough-friendly operation - Easy to use - Stainless steel side plates - Number of divisions: 30 pieces - Body size: No. 3 - Dough weight: 30 - 100 g - Capacity: approx. 10,000 dough pieces/h The machine has been completely overhauled and is in excellent condition.

PRESS DESIGN   drive system: eccentric / crank PRESS FORCES   total force (nominal): 45 to PRESS TABLE   table surface (left-right): 700 mm   table surface (front-back): 440 mm   opening in bed (diameter): 40 mm SLIDE   table surface (left-right): 410 mm   table surface (front-back): 280 mm   stroke rate (max.): 110 /min SLIDE (MECHAN. PRESS)   slide adjustment: 65 mm   stroke min.: 0 mm   stroke max.: 90 mm   main drive power: 5.5 kW TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 380 mm   distance between columns (H-frame): 360 mm ATTACHMENTS (PRESSES)   2-hand engagement: yes   foot engagement: yes   European CE standards: yes

Properties: Volume 200 L Material V2A (AISI 304) 1.4301 Surface on the outside marbled III C Total height 1900 mm Overall height 1770 mm Cylinder length 1020 mm Diameter width 477 mm Operating pressure 0.99 bar Number of feet 3 or 4 [ 5000 characters max., no information on the advertiser ] Properties: Volume 200 L Material V2A (AISI 304) 1.4301 Surface on the outside marbled III C Total height 1900 mm Overall height 1770 mm Cylinder length 1020 mm Diameter width 477 mm Operating pressure 0.99 bar Number of feet 3 or 4 [ 5000 characters max., no information on the advertiser ] Properties: Volume 200 L Material V2A (AISI 304) 1.4301 Surface on the outside marbled III C Total height 1900 mm Overall height 1770 mm Cylinder length 1020 mm Diameter width 477 mm Operating pressure 0.99 bar Number of feet 3 or 4 Description Tank topstock: Manhol ...

1 punching machine (14), manufacturer Kaiser, type KSTU 3500-25-6P, year of manufacture 2000, press force 350 t, stroke rate 20-100/min, stroke height 40 - 250 mm, ram adjustment 200 mm, installation height 700 mm, table size approx. 1,000 x 2,700 mm, control system, manufacturer Siemens, type Simatic Multipanel (retrofitted), force measuring unit, manufacturer Brankamp Marposs, type Prokos X1, two-hand operation, material discharge belt, downstream incline conveyor, coil unwinding reel, manufacturer Dreher, type 2380P, year of manufacture 2000, SN 0051, alignment unit, buffer section, belt feed, manufacturer Dreher, separate switch cabinet system, manufacturer Rittal, cooling unit, accessories: workbench, partition lighting, pull-out cabinet, swivel chair Find more here - / Contact us at -

1 press system, manufacturer Exner, type EXSBZRD 500/100, built in 2002, drive power 121 kW, pressing force 5,000 kN, overhauled in 2018, stroke length max. 600 mm, working speed max. 16/30 mm/s, machine weight 82,000 kg, table size approx. 1,000 x 3,000 mm, control system, manufacturer Siemens, type Simatic Multipanel, separate two-hand control, upstream light barrier, manufacturer Sick, separate control panel, manufacturer Rittal, control system, manufacturer Siemens, type OP17, feed unit, manufacturer AMT, type WV400/160, year of manufacture 2008,control panel, control unit, manufacturer Rexrodt, separate switch cabinet system, additional transfer unit/material feed, vertical material buffer, 6-fold feed-through unit, oiling, manufacturer Ratiol/Stöber Find more here - / Contact us at -

1 hydraulic double-column press (11), manufacturer: Exner, type EX100SBZR, built in 1988, power 42 kW, pressing force 1,000 kN, GG 11 Exner, type EX100SBZR, built in 1988, SN 10094, power 42 kW, pressing force 1,000 kN, GG 11,000 kg, overtravel 26 mm, table size approx. 900 x 1,100 mm, swivel chair, separate control panel, control system, manufacturer Siemens, touch panel, two-hand operation, manufacturer Sick, type XY2SB, front material feed, linear travel, approx. 1,000 mm Find more here - / Contact us at -

1 hydraulic double-column press, manufactured by Exner, type EX80SB, built in 1987, power 15 kW, pressing force 800 kN, GG 5,300 kg, overtravel 38 mm Find more here - / Contact us at -

KOMPLETE RUF ANLAGE BRIKETPRESSE RUF600 600KG/H YEAR OF MANUFACTURE 2009

Dynajet 1000 me, used, blue Operating pressure: 1000 bar, Flow rate: 17 l/min, Drive: electric 35 kW, 400 volts, 63 A, Operating hours: approx.: 427 h, Trolly, incl. gun, 10 m HD hose, 15° flat spray nozzle,

upper amp; lower Wila tooling 5 axes: X / X´ / R / Z1 / Z2 Capacity: 50 ton x 2550 mm Backgauge: CNC Control: TS3 Passage between uprights: 2550 mm Max stroke: 265 mm Max distance between table -- ram: 515 mm Locking speed: 90 mm/sec Working speed: 20 mm/sec Returning speed: 90 mm/sec Electric motor (power): 9 kW Length: 3400 mm Depth: 1850 mm Height: 2820 mm Weight: 5 ton

A CNC sheet bending machine Amada is available. Working width: 4000mm, pressing force: 2200kN, stroke: 350mm, axes: 8. Machine dimensions X/Y/Z: approx. 5600mm/2650mm/3300mm, weight: approx. 18000kg, control: Amada. An on-site inspection is possible.

Manufacturer: EXNER Model: PG 80 Year of Manufacture: 2014 The EXNER PG 80 is a four-column hydraulic tool testing press for testing stamping, forming, embossing, and drawing tools. It is designed for high precision and durability, with modern proportional hydraulic control and digital force display for tool setup and testing. Technical Data Press Ram - Number of press cylinders: 2 pcs - Nominal force (adjustable): 2 × 400 kN - Return force: 2 × 150 kN - Stroke: 350 mm - Ram width: 2100 mm - Ram depth: 840 mm - Guide length: 750 mm - Ram speed under load (100%): approx. 0–10 mm/s - Ram return speed: approx. 0–20 mm/s - T-slots (DIN 650): 18 mm - T-slot pitch: 150 mm Installation Space - Installation height (top to bottom): 550 mm - Table width: 2100 mm - Table depth: 840 mm - Table T-slots (DIN 650): 18 mm - T-slot pitch: 90 mm - Table passage (W×D): 1300 × 120 mm (to be  ...

PRESS DESIGN   drive system: eccentric / crank PRESS FORCES   total force (nominal): 50 to PRESS TABLE   table surface (left-right): 700 mm   table surface (front-back): 450 mm SLIDE   table surface (left-right): 440 mm   table surface (front-back): 360 mm   spigot hole diameter: 40 mm   stroke: 90 mm   stroke rate (max.): 70 /min SLIDE (MECHAN. PRESS)   slide adjustment: 70 mm   stroke min.: 0 mm   stroke max.: 90 mm   main drive power: 3 kW TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 300 mm DIMENSIONS / WEIGHTS   space requirements -left/right-: 700 mm   space requirements -front/back-: 1295 mm   total height: 2360 mm   total weight approx.: 3000 kg

PRESS DESIGN   drive system: eccentric / crank PRESS FORCES   total force (nominal): 80 to PRESS TABLE   table surface (left-right): 860 mm   table surface (front-back): 620 mm   thickness of bolster plate: 70 mm   opening in bed (diameter): 165 mm SLIDE   table surface (left-right): 570 mm   table surface (front-back): 390 mm   spigot hole diameter: 50 mm   stroke: 120 mm   stroke rate (max.): 67 /min SLIDE (MECHAN. PRESS)   slide adjustment: 90 mm   stroke min.: 9 mm   stroke max.: 120 mm   main drive power: 5.5 kW TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 360 mm DIMENSIONS / WEIGHTS   space requirements -left/right-: 1420 mm   space requirements -front/back-: 1700 mm   total height: 2990 mm   total weight approx.: 5600 kg

Block size press Müro 5000/A4 WT; good condition; cleaned and tested; Heat baffle; Stack increase; with dryer. Block gluing machine Müro 5000/A4 WT; good condition; cleaned and checked; pile elevation; heating sheet; with heater.

Eccentric press PEE I 250, in working conditon.

Rutil Vertial Injection Moulding Machine Year of manufacture: 2001 Type: Injection Configuration: Vertical Clamping force: 350 tons Injection volume: 2000 cc Upper intermediate frame: Yes Lower intermediate frame: Yes Heater plate dimensions: 600×650 mm Tie bar distance: 600 / 340 mm Additional heating option: Yes Sliding plate: Yes

Key data: 600 t

Max Tool length: 3000mm Max Tool Width: 2000mm Min Tool Height: 500mm Total Tool Weight: 20,000kg Max Closing Speed: 400 mm/sec

Press force: 1250 KN, Stroke rate: 55 min-1, Plunger adjustment: 75 mm Stroke: 20-120 mm, Motor power: 11 kW, Voltage: 380 V Machine weight: 8.6t Projection: 340 mm, Pusher clamping surface: 620 x 300 mm, Table clamping surface: 650 x 1000 mm, Ortlinghaus hydraulic clutch with double brake, Two-hand control device Demolition at the pestle was professionally repaired.

Manufacturer: Hans Schoen Model: NH 160 Year of Manufacture: 1988 rebuilt in 2016 The press is being sold without tools or spare parts. Technical Data Press force max.: 1,600 kN Main drive power: 30 kW Speeds Rapid advance from: 300 mm/sec Pressing speed: 18 mm/sec Rapid return: 300 mm/sec Strokes Max. stroke: 150 mm Max. daylight opening: 450 mm Table and Ram Dimensions Ram area: 730 × 560 mm Table area: 650 × 650 mm Openings Front vertical opening: 750 mm Side vertical opening: 250 mm Heights Table height above floor: 850 mm Table bore diameter: 150 mm Ram bore, Ø H7: 60 mm T-slots T-slots in table, DIN 650 H12 diagonal: 22 mm T-slots in ram, DIN 650 H12: 22 mm Two pieces, front to back Machine Dimensions Machine footprint approx.: 1,850 × 1,500 mm Machine height approx.: 2,850 mm Find more here - / Contact us at -

Maximum pressure: 50 tons Year of Make: 2006 Pressing force: 65 tons/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1000 mm Dimensions of the tailgate: 920 x 1400 mm Bale weight: 350-500 kg Weight: approx. 13 tons Power connection: 400 V/ 22 kW Bale tying: automatic

Simimpianti 3500×1300 veneer shelf press Shelf length 3500mm Shelf width 1300mm Two Batches Press on 8 cylinders Shelves heated with CO water Operating pressure max 300bar Piston diameter 80mm Machine Weight 7000kg Machine dimensions 435x160x235cmH Net price 65,000zł

Key data: 60 t, 370 mm, 10 mm

Eccentric Press Compressive Force 60 Ton Equipped: -Hydraulic clutch -Hydraulic overload protection

Offer 25450 Specifications: - Compressive force 100 t - Projection 300 mm - Table size approx. 650 x 450 mm - Height-adjustable table - Diarrhea hole in the table approx. 200 x 100 mm - Large installation height approx. 450 mm - Plunger area 70 x 140 mm - Peg hole in the ram 40 x 80 mm - Tappet adjustability 60 mm - Stroke adjustment 10 - 100 mm - Stroke rate 80 rpm - Pneumatically assisted coupling - Drive 380 V / 5.5 kW - Space requirement approx. W 1350 x H 2550 x D 1600 mm - Weight approx. 5000 kg

Offer 25471 Specifications: - Compressive force 75 t - Projection approx. 300 mm - Table size approx. 800 x 600 mm - Height-adjustable table - Stroke adjustment approx. 16 - 140 mm - Plunger adjustment 80 mm - Stroke rate 80 rpm - Pneumatic connection - Drive 400 V - Space requirement approx. W 1800 x H 2450 x D 2000 mm - Weight approx. 4000 kg

It is a used, reconditioned Fortuna bun press fully automatic for sale. The machine head can be swivelled electrically and switched off with active movement. Weight range of the machine is 40gr. - 110gr. per piece of dough (30 pieces). Incl. 3 x plates (more plates on request). Price on request.

Electricity connection 400V 13kW 2 heating plates à 1200 x 2250 mm Heating plates controlled by 2 thermostats Press pressure at 250 bar LxDxH: 2590 x 1330 x 1950 mm Weight approx. 2800 kg Press thickness 380 mm

Technical data: Material width: min. 130 mm, max. 270 mm Material width: max. 244 mm Print repeat length: min. 101.6 mm, max. 254 mm Machine components: • Corona treatment • 5 × offset printing units • 1 × flexo printing unit • Flat hot foil stamping unit • Flat die-cutting unit

Manni 2500×1300 Shelf Press Shelf length 2500mm Shelf width 1300mm Press on 4 cylinders Shelves heated with CO water

Key data: 100 t, 330 mm, 10 mm

Press Type P 100 RE Pressure 100 ton Free passage between the two uprights 420 mm Slab dimensions 610 x 410 mm Table dimensions 950 x 650 mm Installation height plunger lower 400mm Plunger position 90 mm Stroke rate 55 min Motor power 7.5 KW Weight 7000 kg Press is equipped : - Air coupling - Hydraulic overload protection

The Dorst TPA 15/3 is a used mechanical powder compaction press designed for precision and efficiency in industrial applications. It provides a maximum pressing force of 150 kN and a withdrawal force of 100 kN, supporting a variety of compaction tasks. With an upper punch stroke of 100 mm and a range of 70 mm for adjusting the travel, this machine offers flexibility for different requirements. Operating at speeds of 7 to 32 strokes per minute, it ensures a reliable production throughput. This press allows for a maximum filling height of 70 mm and pressing travel up to 35 mm, suitable for a range of powder compaction needs. The machine is fitted with a compressed air system that has an intake of around 70 liters per minute and a total connected load of approximately 6 kW. It is compact yet robust, with dimensions of about 1400 mm in width, 1300 mm in depth, and 2650 mm in height, weighing ...

Roll Press Fortuna Semi-Automatic Size 4 Semi-automatic 30-piece machine for perfect dough pieces Robust design for long service life Parting head NEWLY revised Dough filler up to 3300g, Low space requirement Connection 400V, 16A-CEE plug Dimensions: 580 x 580 x 1350 mm, WxDxH Used machine overhauled Quality from a specialist company! Benefit from over 35 years of experience! Option: Stainless steel pedestal Wirkteller Neu Service Package Maintenance contract Instruction & Commissioning Delivery

Roll Press Fortuna Semi-Automatic Size 4 Semi-automatic 30-piece machine for perfect dough pieces Robust design for long service life Parting head NEWLY revised Dough filler up to 3300g, Low space requirement Connection 400V, 16A-CEE plug Dimensions: 580 x 580 x 1350 mm, WxDxH Used machine overhauled Quality from a specialist company! Benefit from over 35 years of experience! Option: Stainless steel pedestal Wirkteller Neu Service Package Maintenance contract Instruction & Commissioning Delivery

Pass-through press for glued glue ITALPRESSE PL/9 Shelf length 3000mm Shelf width 1300mm Number of vertical cylinders 6 Pressure of 90t vertical cylinders Diameter of vertical cylinders 70mm Number of horizontal cylinders 6 Heating shelves with a high-frequency generator The line consists of: -Material feeding section -Glue application section -Material loading section -Press PL/9 -Material receiving table CE Certificate Line dimensions 740x770x235cmH Weight about 8000kg

A "Raster Zeulenroda" (today Zeulenroda Presstechnik) step press type "Paust 16.2" with 160 kN press force is sold. The machine was completely overhauled in 2006 and has been in use in 1-3 shifts since then. A visit is possible from Monday to Friday.

The Dorst TPA 6 is a used mechanical powder compaction press suitable for various industrial applications due to its robust performance and flexibility. It boasts a maximum pressing force of 60 kN and a withdrawal force of 30 kN, addressing a wide range of compaction needs. The machine supports a maximum filling height of 70 mm and a pressing travel of 30 mm, with an upper punch stroke of 95 mm and an adjustable travel of 50 mm. This ensures precise control over the compaction process. Operating at speeds between 7 to 32 strokes per minute, the Dorst TPA 6 consumes approximately 70 liters of compressed air per minute and has a total connected load of about 3.5 kW. It measures 2220 mm in width, 1060 mm in depth, and 2250 mm in height, weighing around 1,200 kg. With a gear oil capacity of 12 liters and a workplace-related sound level of 75 dB(A), it is designed to endure continuous use whi ...

Used Roll Press FORTUNA, Machine Size 4 -In Bakery Condition- - 30 hollows per plate - Weight range: 40 - 110g - Condition: very good, - Video on request A viewing is of course possible by arrangement.

The Dorst TPA 4 is a used mechanical powder compaction press well-regarded for its sturdy performance in various industrial settings. It features a maximum pressing force of 40 kN and a withdrawal force of 30 kN, making it versatile for different compaction tasks. With a maximum filling height of 70 mm and a pressing travel of 30 mm, this machine efficiently handles varied operational demands. The upper punch has a stroke of 95 mm with an adjustable travel of 50 mm, enabling precise control during processes. The press operates within a speed range of 7 to 32 strokes per minute, consuming around 70 liters of compressed air per minute and requiring a total connected load of approximately 3.5 kW. It is designed with dimensions of 2220 mm in width, 1060 mm in depth, and 2250 mm in height, while weighing about 1,200 kg. The gear oil capacity is 12 liters, ensuring durability and the ability t ...