rotary press used for sale

Dear Sir or Madam, We have in the offer for you The Tiger metal and scrap press.These are available with different press box dimensions and Bale dimensions (25 x 25, 30 x 30, 40 x 40). Cutting edges on all three sides of the box give the machine the ability to handle oversized materials. The machine is equipped with side pre-loading box, oil cooler and radio remote control. (further equipment possible) Out of stock. If you have any questions, please do not hesitate to contact us. To make an offer, we need your company data and a direct e-mail address.

Pressure transmitter for measuring gases, vapors and liquids ROSEMOUNT 2088

USED PRESSURE TRANSMITTER WITH SPACER RING VEGABAR 81

Specifications: - Compressive force 60 t - Projection 350 mm - Table size approx. 900 x 600 mm - Table height adjustable - Diarrhea hole in the table approx. 300 x 200 mm - maximum installation height approx. 360 mm - Stösselfläche approx. 340 x 160 mm - Cone hole in the plug 40 mm - Plug adjustability 60 mm - Stroke adjustment 10 - 90 mm - Stroke rate 110 1/min - 2 hand operation - Pneumatic connection 6 bar - Flywheel drive / speed infinitely adjustable - Rotary wedge coupling - Drive 400 V / 5.5 kW - Space requirement approx. W 2000 x H 2200 x D 2400 mm - Weight approx. 4500 kg - mechanical clamp feed MABU type ZPL 11 with 3 roller straightener

- 2 ZK yeast tanks, Fabr. BAM, each with a capacity of 59.98 hl, zul. Operating overpressure 3.5 bar, in stainless steel, standing on 3 feet, with 3 cooling zones (2 x frame + 1 x cone), with screwed swivel cone tip, with agitator in the cone, with Spray head, top with ladder bracket, YOC 1985. - 2 ZK yeast tanks, Fabr. Steinecker, with a capacity of 62 hl each, zul. Operating overpressure 3.5 bar, in stainless steel, standing on 3 Feet (1 foot on load cell), with 3 cooling zones (2 x frame + 1 x cone), with screwed swivel Cone tip, with agitator in the cone, with spray head, pulled down cleaning line, top with conductor bracket, YOC. 1981.

- 2 pressure tanks with 61.1 hl, Fabr. Noble, 2 bar, in stainless steel, single-walled, standing, with manhole in the lower frame, Spray head with downed cleaning line, fittings, with papers, Ø: 1,500 mm, H: 4,200 mm. - 4 pressure tanks with 102.2 hl, Fabr. Noble, 2 bar, in stainless steel, single-walled, standing, with manhole in the lower frame, Spray head with downed cleaning line, fittings, with papers, Ø: 1,800 mm, H: 4,900 mm.

Proportional pressure control directional control valves, solenoid valves, pneumatic valves, air valves, pressure valves, valve blocks, control blocks -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm -Weight: 2 kg

Pressure sensor -Type: 3405BM2X2X2920 -Measuring range: 0-250 bar G -Max. Pressure: 1034 bar G -Input: 10-30 VDC -Output: 4-20 mA -Number: 2x available -Price: per piece -Weight: 0.5 kg

SPECIFICATIONS: Membrane press for gluing doors, curves and other wooden elements Dimensions mm: 2400 x 1120 Heating by electrical resistance Complete with decompressor, timer and tarpaulins

Make: RIJVA Model: 502/1 S/N: 405 Cap: 12 tons

Portal straightening press with 400 T capacity Oil-hydraulic double column press a) No-load and pressing speed up to 17 mm/sec b) Opening speed up to 60 mm/sec c) Table size 6000x3000mm d) Open height 1500 mm e) Total size approx. LBH 6000 x 5000 x 4500 mm f) OIL temperature display on the tank g) Lubrication via lubrication nipples h) table in grid construction, i) Operation on swivel arm, mounted on the bridge j) Pressure setting from 60 T to 400 T via MONITOR k) Bridge moves through two geared motors, over racks l) Cylinder moves to the left and right over racks m) Machine body powder-coated, or double-painted n) T-grooves according to customer requirements o) Cylinder induction hardened PORTAL PRESS Thermally neutral 80 – 120 °C Number of operating pages 3 pages Forces Pressing force max. 4000 kN Free tearing force ...

Standard accessories: - 10m high pressure hose DN10, kink protection on both sides - HDP350 high-pressure gun with quick coupling and swivel joint in the input - Double jet tube with nozzle 065 and low pressure nozzle Optional (additional cost): - Hose reel - 30 m high pressure hose The images contain additional options. Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

Pressure regulator intermediate plate -Type: LR-ZP-A/B-D2 35428 -From: 0 bar to: 12 bar -Price: per piece -Quantity: 8x Available -Weight: 2 kg

Hydraulic pressure switch -Type: TGL10952 -Adjustable: from 0 to 320 bar -Price: per piece -Number: 9 available -Weight: 0.5 kg

New industry-standard hotbox for up to 400 bar and up to 28 litres per minute. EQUIPMENT - Epoxy coated steel frame with stainless steel cover - 4-wheel chassis with solid rubber tyres - Connection hose 1,5m - Water inlet temperature max. 60° - Heating capacity approx. 90 kW - Water outlet temperature in the steam range up to max. 140°C - With thermal switch and flow monitor Diesel tank: 20L Power supply: 1x 230V Dimensions: (L x W x H): 700mm x 570mm x 800mm Weight: 65kg Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

Proportional pressure control directional valve, solenoid valve, pneumatic valve, air valve, pressure valve, valve block, control block -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm -Weight: 2 kg

New industry-standard hotbox for up to 300 bar and up to 28 litres per minute. EQUIPMENT - Epoxy coated steel frame with stainless steel cover - 4-wheel chassis with solid rubber tyres - Connection hose 1,5m - Water inlet temperature max. 60° - Heating capacity approx. 90 kW - Water outlet temperature in the steam range up to max. 140°C - With thermal switch and flow monitor Diesel tank: 20L Power supply: 1x 230V Dimensions: (L x W x H): 700mm x 570mm x 800mm Weight: 65kg Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

5/2 Pressure Booster -Type: DPA-40-10 537273 -VN: 43 -1: 2.5-8 bar 2: 4.5-10 bar -Weight: 1.5 kg

New hotbox in the industry standard for max. 200 bar and up to 28 liters per minute. EQUIPMENT - Epoxy coated steel frame with stainless steel cover - 4-wheel chassis with solid rubber tyres - Connection hose 1,5m - Water inlet temperature max. 60° - Heating capacity approx. 90 kW - Water outlet temperature in the steam range up to max. 140°C - With thermal switch and flow monitor Diesel tank: 20L Power supply: 1x 230V Dimensions: (L x W x H): 700mm x 570mm x 800mm Weight: 65kg Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

Proportional pressure control directional control valves, solenoid valves, pneumatic valves, air valves, pressure valves, valve blocks, control blocks -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm Price: per piece -Quantity: 2 available -Weight: 2 kg/piece

Nilsfisk ALTO NEPTUNE 8, Price: 3.500 € netto, year of construction 2008. Hot water high-pressure cleaner for the most demanding cleaning tasks. The device combines powerful pressure with high water output, which is needed for cleaning heavy soils in agriculture, construction, transport or industry. In addition to the convincing cleaning effect, the high alluvial performance is particularly effective. Price is negotiable. Shipping possible. The sale is carried out on behalf of the customer. Prior sale and error excepted. The terms and conditions of Cleantec-MR apply.

Hydraulic pressure switch, pneumatic pressure switch -Type: EDS 1100-050-1-009 -Pressure: 25 bar -Operating voltage: 24 VDC -Signal output: 0-5 VDC -Weight: 0.3 kg

New VDL 2D chiseling machine with the possibility of automatic drilling at distances of 25 and 32 with the possibility of tilting and turning in 2 directions. Technical parameters: Control of the machine with 1 lever Power of the main motor: 1.5 kW Tool speed: 2850 rpm Spindle diameter: 3 - 16 mm Stroke of the spindle: 180 mm Dimensions of the table: 600 x 450 mm Weight of the machine: 320 kg

Hydraulic pressure switch, pneumatic pressure switch -Type: EDS 1691-NC-016-000 -Pressure: 16 bar -Operating voltage: 24-20 VDC -Signal output: 4-20 mA Price: per piece Quantity: 2 available -Weight: 1 kg

Pressure valve, pressure gauge, pressure indicator, manometer -Measuring range: 0-6 bar -Fitting: Ø 63 mm -Thread: M12/1.5 mm -Price: per piece -Quantity: 10 available -Weight: 0.2 kg

2 x 10 T, adjustable from 1.3 to 10 T Plunger size 250x250mm forward 10 mm second Backwards 25 mm second Travel 100 mm per side, Interior 200 to 400 mm Two-hand operation Motor 1 KW Tank for 60 L hydraulic oil the machine can also be supplied in other sizes and thicknesses.

Portal straightening press with 300 T capacity a) No-load and pressing speed up to 17 mm/sec b) Opening speed up to 55 mm/sec c) Table size 2500x1600mm d) Open height 700 mm e) Total size approx. LBH 4500 x 2300 x 3700 mm f) OIL temperature display on the tank g) Lubrication via lubrication nipples h) Table in grid construction, with T grooves according to customer requirements, otherwise 22mm i) Operation on swivel arm, mounted on the bridge j) Pressure setting from 50 T to 300 Tvia MONITOR k) Bridge moves through two geared motors, over racks l) Cylinder moves to the left and right over racks m) Machine body double painted n) Cylinder induction hardened Design Press type PORTALPRESSE Thermally neutral 80 – 120 °C Number of operating pages 3 pages Forces Pressing force max. 3,000 kN Free tearing force max. 500 kN Pressure build-up time Closed tool St ...

Pressure switch -Type: C6045D 1043 -0.2-3 mbar -220/240 VAC 50 Hz 12(2) A -Pmax: 100 mbar -Protection class: IP 40 -Quantity: 3 pieces available -Price: per piece -Weight: 1.2 kg/piece

Precise and heavy machine for drilling slotted holes. The maximum hole length is optional. In the standard version, it is 400 mm. The tool is fixed. The height is adjusted by raising the work table. Spindle power: 1.5 or 2.2 kW

SPECIFICATIONS: Vertical frame press for windows and doors Hydraulic operation machining length mm: 3,000 machining height mm: 2,000 Installed capacity KW: 1.6 Beam 2 horizontal bars 3 Vertical bars with pusher

Cold water high-pressure cleaner and hydraulic oil demand unit. Working pressure: Infinitely variable up to 320 bar. Required quantity: up to 21l /min (1,260 l/h) Pump: 3-plunger, all-ceramic Engine: 2 cylinders 4 stroke petrol engine Motor power: 16.4 kW Speed motor/pump: 3,250/1,450 rpm Pump drive: Gearbox Fuel consumption:approx. 5.5l/h Volume fuel tank: 20l Pressure outlet (water) M221,5 AG Heating capacity Olbrenner Empty Weight: 110kg Dimensions(LWH) 757999cm Article no.: 1 486 089

High-pressure radial fan, dust extraction fan, exhaust gas extraction, welding fume extraction, extraction, fan, pressure blower, vacuum blower -Engine power: 0.37 kW -Performance data: not available -Connection input: Ø 65 mm -Connection output: Ø 60 mm -Dimensions: 510/480/H470 mm -Weight: 49 kg

FRITZ MÜLLER ZE 625-4 hydraulic press was built in Germany by Fritz Müller GmbH & Co. KG. The machine has been continuously maintained and upgraded throughout its service life. The first major overhaul was carried out in 1988 by the manufacturer’s service Machinenfabrik Mueller-Weingarten AG. A second overhaul was carried out in 2020, during which the press was brought up to current safety requirements. As part of this overhaul, a new control system based on a SIEMENS SIMATIC S7 PLC controller and a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel was installed, the entire electrical system was replaced, seals were replaced and light curtains were installed. The FRITZ MULLER ZE 625-4 is an extremely versatile press designed for even the most demanding metal forming operations. It is capable of performing operations such as deep drawing, stamping, forging, straightening large w ...

Cold water high-pressure cleaner Working pressure: infinitely variable up to 350 bar Required quantity:up to 21l/min (1.260l/h) Pump:3-Plunger All-Ceramic Engine:2 Cyilinder, Hatz Diesel,air-throated Motor power:17 kW Speed motor/pump: 2,900/1,450 rpm Pump drive: V-belt Fuel consumption:approx. 4,0l/h Volume fuel tank:20l Pressure outlet (water):M221.5AG Heating capacity Olbrenner Empty Weight:215kg Mass(LWH) 918096 Article no.: 1 492 060 or 1 492 002

Hot and cold water high-pressure cleaners Working pressure:infinitely variable up to 350 bar max requirement quantity:16l/min Pump:3 Plunger,All-ceramic Engine:Kubota 3-cylinder diesel Motor power:13kW Speed motor & pump: 3000/1,090 rpm Pump drive:V-belts Fuel consumption:3,9l/h Volume of carbon tank:70l Volume water tank:300l Pressure outlet (water) M22 1.5IG Heating capacity olburner: max1115kW (approx. 95°C) Consumption Olbrenner: approx. 7l/h Construction:self-supporting frame on frame with forklift pockets Empty weight:about 680kg Mass(LWH) 152122146 Dimensions open (LWH) 183122195 Article no.: 1 480 030

Hot and cold water high-pressure cleaner Working pressure: infinitely variable up to 220 bar max demand quantity 26l/min Pump:3-Plunger,All-Ceramic Engine: Kubota 3-cyilinder diesel Motor power: 13kW Speed motor and pump: 3,000/1,760 rpm Pump drive: V-belt Fuel consumption: 3,9l/h Volume fuel tank: 70l Pressure outlet: (water): M22 1.5 AG Heating capacity Olbrenner : max 1115kW (ca 95° C) Consumption Olbrenner: approx. 7l/h Construction: Skid - Construction Empty weight: about 420kg Dimensions(LWH) 12080112cm Article no.: 1 546 712

EHT VarioPress 175-35 CNC press brake was built in 2004 in Germany by EHT Werkzeugmaschinen GmbH (now TRUMPF). Currently, the machine is installed 50 cm below floor level, and the new installation requires either a recessed area to be prepared in the floor beneath it or a platform to be built for the operator. The machine is designed for precision machining of workpieces with a maximum length of 3550 mm. The machining process is performed with a high press force of 175 tonnes, which, combined with an extremely stable design, guarantees excellent bending results, even during the most intensive challenges. All this is complemented by the advanced CYBELEC control system, which significantly facilitates the daily operation of the machine. The EHT VarioPress press brake weighs 14900 kg. Technical specifications of the EHT VarioPress 175-35 press brake - CNC controller: CYBELEC DNC 1200 ...

Nominal force 100 t Stroke - 250 mm motor 3 kW more info on request

Technical details Pressure 110 t Technology Passage width 1200 x 1000 mm Stroke 1200 mm Machine weight approx. 12 t Space requirement approx. 4500 x 4300 x 2700 mm Master cylinder 1 piece Installation height (distance table to plunger plate) 1200 mm Table height 700 mm Table can be extended by 1200 mm Table tiltable by 45 degrees Upper tool folds down by 180 degrees Table rotatable by 180 degrees Table load max. 10 t Travel speed of the table 25 mm/sec Flow speed 195 mm/sec Return speed 130 mm/sec Working speed adjustable from 0 to 10 mm/sec. Table area between the columns 1250 x 1000 mm Engines WEG Accessories Paint structure RAL 7035 (light grey) Additional information Painting cladding, doors, maintenance balcony RAL 1021 (Yellow) Painting accessories RAL 7021 (dark grey) Columns and cylinders are made of tool steel SAE 1045 (identical to German standard C4 ...

for pressing PET bottles

Vacuum press, vacuum table, vacuum table from Joos with silicone membrane Universally applicable press, veneer press for veneering, coating, mold gluing, mold veneering, edge banding, etc. With this press, you can do without a hydraulic veneer press, with some restrictions. New heat-resistant silicone membrane, extremely stretchy and easy to clean. Can also be used for forming preheated thermoplastic materials such as acrylic glass or solid surface materials. Inner frame dimensions approx. 2900 x 1410mm, usable area approx. 2800 x 1300mm Working height approx. 900mm Vacuum pump Becker VT4.40, 400V, 1.5 kW with 40 m³/h capacity and two vacuum tanks each 200 liters, thus comfortable working, fast evacuation. Electronic vacuum pressure switch, which means that the pump switches off when the vacuum is reached and does not run constantly Mobile on four swivel castors, lockabl ...

Stock number: U2391 Used rotary tablet press by Killian (DE) model T100/18 EU-B. Machine has 18 punches. Die dimensions: diameter 30.16 mm x height 22.22 mm. Working output from 5400 tablets up to 129600 tablets, depending on size, shape and product. Maximal tablet diameter 16 mm. Maximal filling up to 16 mm. Machine has hydraulical compression. Pre-compression force up to 60 kN. Main compression force up to 65 kN. Machine has local control panel and electric cabinet with work recording computer and printer. Technical documentation included with machine. Toolings not included.

Stationary high-pressure pump unit Hammelmann HDP 142 on base frame. Similar but no Kamat, Uraca, Woma. Pump type: HDP 142 Operating pressure: 610 bar Flow rate: 78 l/min. Drive speed: 1500 rpm. Drive power: 86 kW with AC M 280 M-4/HE electric motor 90 kW, IP55, with pressure control valve, with safety valve, with oil cooling system. Dimensions LxWxH: approx. 1,700x850x1,450 mm Weight: approx. 1,200 kg Year of construction: 2018 Condition: after service by Hammelmann in October 2020 only a few weeks run and for more than a year out of operation. In very good used condition.

Compact electric press brake C9 CoastOne - Made in Finland Pressing force: 22T Bending length: 900mm Spindles: 1x22T Control: TC15-2D graphics Backgauge: 2 axis controlled X-R axles Lazersafe photoelectric sensor: 100mm/s delivery speed Bending tool holder: Type A / R1 / AMADA / Promecam Quick release system TEDA Speed Grip 4x Adapter Front support tables Front light 1x set of bending tools incl. 36 months warranty after installation Delivery excl.; at call Viewing under electricity possible at any time by appointment!

Key data: 300 t

DURENDUS 300 T Workshop Press – Single Column Press – 1,600 mm Clear Width, 550 mm Stroke The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. It is a hydraulic workshop press for press-fitting, straightening and assembly work in the workshop and industrial sector. Base price: 22.450 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. Table top with X-shaped T-slot 800 × 1,200 × 120 mm Pressure adjustment Lateral displacement  ...

Inv. Num. : 5698 Type: LKT 250 Producer: METALPRESS Created: 1974, GO 2002 Parameters: Compressive force: 250 t Table length: 1150 mm Top table width: 1580 mm Maximum stroke rate top table: 7-25 1/min Ram stroke: 250 mm Adjusting the plunger: 100 mm Machine weight: 22950 kg GO 2002: converted to hydraulic clutch electronic control

pressure: 160 t stroke: 400 mm table surface area: 1100 x 635 mm pressing speed: 6,57 mm/sec return speed: 11,62 mm/sec oil pressure max. in the work cylinder: 412 bar oil volume: 40 l dia. of piston: 145 mm column daylight: 1120 mm voltage: 400 V / 50 Hz dist. between pillars (front to rear): 350 mm total power requirement: 5,5 kW weight of the machine ca.: 1,2 t dimensions of the machine ca.: 1,7 x 0,9 x 2,1 m • unused workshop press, • manual and hydraulical operation, • horizontally moveable pressure cylinder, • working table hydraulical adjustable in height, • cylinder Ø 220 mm, piston base Ø 145 mm. • 2 support prisms • CE marking The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 400 t

DURENDUS 400 T Workshop Press – Single Column Press – 1,600 mm Clear Width, 550 mm Stroke The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. It is a hydraulic workshop press for press-fitting, straightening and assembly work in the workshop and industrial sector. Base price: 35.950 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. Table top with X-shaped T-slot 800 × 1,200 × 120 mm Pressure adjustment Lateral displacement of ...

Key data: 500 t

DURENDUS 500 T Workshop Press – Single Column Press – 1,600 mm Clear Width, 550 mm Stroke The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. It is a hydraulic workshop press for press-fitting, straightening and assembly work in the workshop and industrial sector. Base price: 46.950 € net Options (on request): The options listed are based on completed customer projects and enable the machine to be specifically adapted to the respective application. The basic machine represents a functional basic design – in practice, in most cases it is expanded with additional equipment and configured accordingly for the specific project. Table top with X-shaped T-slot 800 × 1,200 × 120 mm Pressure adjustment Lateral displacement of ...