roscher und eichler used for sale

Alup Compressor SCR 30 - Height: 125cm - Width: 125cm - Depth: 75cm - Weight: 600kg Good condition fully functional can be visited and tried out on site. Shipping abroad. Bilopzitsev Visit: Basically, I would like to point out to you that in order to avoid misunderstandings, the article can be viewed before purchase and tested under electricity. Please ask questions before purchasing to avoid any ambiguity. If you have any general questions or make an appointment for a visit, I can be reached at any time at the telephone number below. Errors in the description and intermediate sale reserved. The VAT is shown separately on my invoices. Shipping with forwarding.

! A B S O L U T E R S O N D E R R R E I S ! Drill grinding machine manufacturer Avyac from France, Built in 1983, Weight 800kg, Fully automatic with praezisions 6 jaw lining for drills up to 51mm. All dimensions of a drill can be adjusted. Machine under power ready for use. Special price Alzmetall Gühring Garant MK2 MK32 MK4 MK5 Flott Gillardon

Key data: 500

Automatic under-table crosscut saw The complete unit consists of the automatic under-cutting saw (UKS 600 HA), a feed line with a new automatic positioning insert (TigerStop TS 6.0 L / 2019) and a run-off runway. 1. Automatic under-cutting saw UKS 600 HA - Working height: 800 mm - Diameter connection socket for suction chip catcher (machine): 120 mm - Diameter connection socket for suction contact hood: 120 mm - Suction speed: 20 m/sec - Suction capacity: 2000 m3/h - Diameter saw blade: 500 mm - Diameter saw blade bore: 80 mm - Saw blade overstand at 500 mm saw blade: 160 mm - Cutting speed at 500 mm saw blade: 78 m/sec - Short stroke for small wood cross-sections up to 240 x 120 mm (up to 36 strokes/min) - Long stroke for larger cutting widths up to 600 x 120 mm (up to 18 strokes/min) - Automatic protective hood and holding device - Cut triggering via two-hand control ...

Used Final View Labels-MHD Control Device No. 2TG024887 Year built: 2010 Out of service since 2016 Device specification: Application (B/h) 36,000 Installation location behind the labeling machine Task: Container insection - underfilling and overfilling Container inspection - safety ring Detection in the labeler - hull label Recognition in the labeler - back label Accessories SPECTRUM refrigerator Follow-up error labeling machine takes stop signal to line MHD control in the labeling machine Messbrück container inspection version left Trigger bridge oblique lysread lid inspection of the retaining ring Discharge signal control One-segment Heuft Pusher Pusher PSH BG0109 The device has been stored properly by the manufacturer

RECON - complete ground to 1st level undersize 204,5 mm - pn. X11.02001-9047 - incl. counterweights ---------------------------------------------------------------------- ------- Please note: we also have other various RECON parts of different manufacturers / types in stock. We are pleased to provide you with our current stock list. If you have any further questions do not hesitate to contact us

Knife Corta K 1500 / 2000 Photooptic cutting machine working area 1500mm x 3000mm cutting with propane or aceethylene under current.; ready to use

Power range: 200 - 320 kW Rated heat output: 320 kW Maximum permissible operating overpressure: 4 bar Maximum permissible operating temperature: 120°C Length: 3250 mm Width: 2500 mm Height: 2440 mm Diameter of exhaust pipe: 300 mm Fire room volume: 0.77 m3 Power of the combustion air blower: 0.4 kW Power of the rust drive: 0.12 kW Smoke fan power: 2.2 kW Fuels: residual wood (wood chips with and without bark, coarse and fine content max. 20%, main part 60-100%) Fuels according to 1.BlmSchV of 15 July 1988 Water content of the fuel: W20-W40 (dry to moist) Fuel size: G30,G50 (fine wood, medium chip) Feeding: Automatic (manually possible by filling door in emergency mode) The plant is offered with the following attachments: • Insertion unit with insertion screw, motor and attached rotary valve (measurement from boiler output: 1000mm (length) 700m (height with rotary ...

continuous grilling line all stainless steel bottom contact grilling + hot air steam injection belt width 1.000 mm nett length 4.750 mm electrically heated 276 kW underplate max. 260°C air temperature max. 280°C belt washing system adjustable speed dimensions (l x w x h) : ± 6.600 x 1.500 x 2.300 mm

See pictures under electricity with accessories immediately available

Press brake AMADA HFE 220-3 Number of controlled axes / CNC controlled axis: 7 Condition good, ready to use, visit under electricity possible / Condition: good, in use, can be seen under power in Poland Pressure / Pressure: 2200 kN / 220 ton Bending length / working range: 3100 mm Distance between stands / distance between columns: 2700 mm Stroke / stroke: 200 mm Delivery speed / downwards speed: 1-100 mm/s Working speed / working speed: 1-10 mm/s Retraction speed / backwards speed: 1-100 mm/s Dimensions Machine / Machine's dimensions: 4.3 x 2.3 x 3.1 m Weight / Weight: 14 ton Machine has: new safety cards from Pilz, new tool clips, new keyboard of control, new stop finger Machine has: new safety cards by Pilz, new tool clamps, new CNC cover, new back gauge fingers

Horizontal 5-axes CNC lathe Quick tech DT 42 DUO Year 2012 Control: Mitsubishi M70 Machine number: 3264 Weight: 3,400 KG 380 V, 60 HZ 15 KVA S1, S3, X, Y, Z, X 1, Z1 Maximum turning diameter: 42 mm Maximum turning length: 100 mm Spindle bore: 44 mm Speed: 4,000 rpm. Procedures: X: 200 mm Y: 250 mm Z: 235 mm X-1: 235 mm Z-1: 235 mm Bar feeder quick tech BFG 42 with LED display the rod length / position of the rod Year 2012 Machine number: 1154 Weight: 1800 KG 220 V, 60 HZ The machine can be visited at any time under power and is in a good condition. We love to hear from you.

with (wide) swivelling vertical head table size 300 x 1,430 mm table paths: laengs (X-axis) 1,000 mm persive (Z-axis) 520 mm quer (Y-axis) 360 mm installation height under fraes spindle approx. 500 mm Extension of the fraesspindle min./max. 350 mm spindle holder SK 40 spindle speeds 25 - 1,200 rpm feed/rapid speed 12-900 mm/min spindle drive approx. 3 kW Total drive 3.4 kW - 380 V - 50 Hz weight 2,400 as kg;

Selling complete switch production with know how. Production include: Bflvedy7tb 1. 51 moulds for plastic parts, two diferent design of switch type programs, ALL MOLDS ARE IN PERFECT CONDITION. 2. 28 stamping tools for steel parts underconstruction of bottom switches and plugs 3. Complete assembly line with tables pneumatic screv drivers delivery vibration machines for screews and other parts 4. Row half product aprox 50000 parts on stock to assemblle 5. Packed finished stock of switches ready to sell in different types and models. 6. testing equimpent for quality for switches. 7. Complete production information with buyers list , price lists. 8. Showroom glass panels with promotional complete types of switches. 9. Lot of other accessories and equipment -look attached photos many more equipment not on photos of machineenseeker only 15 photos limit. Company has ISO 9001 AND IT ...

Double grinding bracket, knife grinding machine Turning one side quickly, the other side running slowly in the water, e.g. for grinding knives Grinding wheel diameter approx. 300mm Weight approx. 250kg Ready to demonstrate under electricity. Special price

see data sheet available under electricity immediately

Storage tank/ stainless steel tank pressureless, standing Content: 20,000 litres UNI-FIN-FOR B. No. 20-009 GL Dimensions and weight: Diameter approx. 2,600 mm Zyl. Height approx. 3,750 mm Total height with feet approx. 5,370 mm Built: 1992 Material: Stainless steel 1.4301 Wall thicknesses: underbody 3 mm, cylinder + top 2.5 mm Containers with cone bottoms Topsoil: 2 crane eyelets 1 flange nozzle DN 65 1 Vent ingesride DN 100 with bow Tank cylinder: 1 manhole 440 x 340 mm at the top: 1 3/4 Underbody: 1 outlet nozzle with bow pulled forward NW 65 in the outlet pipe there is still a outlet DN 40 otherwise according to photos

Plasma and cutting machine Promotec Ector 30 / 170 Working range: 3000mm x 17000mm 1 x Plasma Ht 2000 Hypertherm cutting up to 25mm 1 x Autogen support up to 100mm machine to visit under power . Without table and filter assembly and commissioning on request; ready for use

See pictures under current with accessories now available

Storage tanks made of V2A without pressure standing, on a stand filled with concrete Content: 30,000 litres Available: 4 pieces UNI-SCHLI-FOR B. No. 18-086 A-D GL Dimensions and weight: Diameter approx. 2,500 mm Zyl. Height approx. 6,000 mm Total height with feet approx. 6,800 mm Material: Stainless steel 1.4301 Wall thicknesses: underbody 4 mm, rest 3 mm Container with lower sloping floor with 3% slope to the outlet and upper cone bottom Topsoil: 2 crane eyelets 2 Threaded nozzles DN 50 1 elbow NW 40 cut off 1 nipples 1" 1 nipples 1/2" Tank cylinder: 1 manhole 450 x 350 mm swivel 7 1/2 Underbody: 1 outlet nozzle NW 50 otherwise according to photos The containers additionally have 1 slanted seat flange NW 150 for agitator without agitator A container has a slight vacuum damage at the top

Machine to the dowel, drill and saw the company EKM spezialmaschinen connection value: 4,4 kW 1 pneum. Workpiece clamping system 1 drill head with 5 spindles in row spacing 25 mm / 40 mm / 40 mm / 25 mm 4 piece glue - and plugs Tools 4 piece adjustable on width 220 mm Under table saw Control PLC Siemens Simatic Fully functional replacement for PLC program on CD,. Shipping dimensions: L 1500 mm x W 1500 mm x H 2400 mm Machine weight: 1000 kg Condition good, fully functional

Storage tanks made of V2A without pressure standing, on a stand filled with concrete Content: 30,000 litres UNI-SCHLI-FOR B. No. 18-087 A-F GL Dimensions and weight: Diameter approx. 2,500 mm Zyl. Height approx. 6,000 mm Total height with feet approx. 6,800 mm Material: Stainless steel 1.4301 Wall thicknesses: underbody 4 mm, rest 3 mm Container with lower sloping floor with 3% slope to the outlet and upper cone bottom Topsoil: 3 crane eyelets 2 Threaded nozzles DN 50 1 nipples 3" Tank cylinder: 1 manhole 450 x 350 mm swivel 7 1/2 Underbody: 1 outlet nozzle NW 50 otherwise according to photos Three of the containers have an additional 1 agitator flange DN 200 A container has a slight vacuum damage at the top

5 axis machininng center (milling/turning from bar) Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 – 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4)

Underscore 5,158:1

FZ15KS HIGH SPEED 4 axis vertical machining center X: 550mm Y: 400mm Z: 360mm 4th axis original Peiseler CNC Siemens 840D Table surface 1050 x 450mm Toolchanger 48 posts ISO 40 Spindle speeds up to 12000 1/min with 4th axis Renishaw broken tool detector Coolant through spindle swarf conveyor Can be inspected under power in our warehouse. Mimu machine tools (Italy)

Used low-pressure flame pipe boiler from LOOS from Gunzenhausen in good condition. The plant was in operation until the demo days and was shut down due to general plant changeover. Manufacturer LOOS Gunzenhausen Type: UN-D 2600 53.0 m2 x 1 bar Built in 1999 Ab. Steam generation 3200 kg / h Ab. Pressure 1 bar Water content 2560 l Brenner Weisshaupt Type L7T Heating oil burner Power 320 - 1957 kW Used last TÜV exam 2018 Dimensions: 4000 x 1900 x 2400 mm Also visit our website. We have a wide range of products in stock for the industry. A visit is worthwhile. The information about our company and the link to our website can be found in the dealer list under Brand GmbH.

Storage tank 85,000 litres of V2A Cat No. 17-00177 used in very good condition Dimensions and weight: GES. height approx.: 5200 mm diameter: 5000 mm Weight: 4100 kg material: V2A - AISI 304, 1.4301 tank top shelf: Central with dome lid diameter 500 mm with 4 clamping screws with fermentation sheet pile connection DN 50 with valve for overpressure DN 50 Tank cylinder: with manhole oval 420 x 320 mm with level indicator with tap hole cover Underbody: flat bottom with 3% slope for residual trace with spout lock flanges with threaded connection DN 50

Solid pump sewage sludge pump Saxlund with double hydraulic aggregate 90Kw + 18.5 Kw used Solid pumping system consisting of 2 x solid piston pumps (duplex pump) oil-hydraulic drive/hydraulic unit. For reliable conveying of sludge of all kinds. Manufacturer: Saxlund 2 cylinder solid piston pump / double pump: Type: 119083 Komm.Nr. 2925-30/59410/2 Operating pressure: max. 280 bar 100/63/1000 Outer diameter: 140 mm Inner diameter: 13 mm Dimensions: 1x approx. 3,700 x 700 x 1,300 mm Dimensions: 1x approx. 3,750 x 850 x 1,800 mm Drive hydraulic unit: Square Bosch Hydraulics Saxlund 9710026 HA1-0 4069 No. SAX.2925-30 Built: 1998 V = 1200 P = 90 kW P = 18.5 kW Dimensions: approx. 2,400 x 1,700 x 1,900 mm ---------------------------------------------------------------------- ---------------------------------------------------------------------- ----------------  ...

see data sheet immediately available under current

Plasma cutting system with Hypertherm HPR 130 with automatic gas console Cutting up to 20mm Working range: 1500mm x 3000mm inlusive filter system Immediately available under current assembly and commissioning on request

Plasma cutting system with Hypertherm HPR 130 with automatic gas console cutting up to 20 mm Work area: 1500 x 3000 mm included filter system available under current mounting and commissioning on request

Tool-fraes machine Ruhla with very extensive trailer to be seen in top condition under electricity Type FUW Built in 1986 Tool holder SK40 stepless feed control Speed control via gearbox Weight approx. 1,800kg Accessories: Box table Quick-aeuferkopf with collet holder and collet set Fine drilling head with collet holder horizontal sub-apparatus universal sub-device SK40 with spiral-fraes device (probably unused) D2evxjf Counter-holder for horizontal fraes long fray edhism 2 stueck Further accessories at an additional cost. Special price

under current Details on request

CO2 laser Bystar 3015 4.4 Kw, Table size 1500 x 3000 mm, incl. changetable, without loader, without suction, Y.O.M. 2006 glass revision in November 2015 under power laser: 28,000 h power on demand

Knife Cortina 2600. Year built:1994 Control KS 20A Plasma: Hypertherm Max 100 (cutting up to 30mm) The suction table: 1500mm x 3000mm. With only one burner car instead of 2 or 3, you have a working width of up to 2000mm. The box program on the PC is the OmniWin CAD. Extraction system: Donaldson 5.5 KW to be visited under electricity commissioning on request

EDM machine - X: 500 mm - Y: 295 mm - Z: 385 mm - C-axis: 360° - Clamping area: 780 x 500 mm - Spacing table - Pinole: 285 - 660 mm - Workpiece weight: 1200 kg - max travel speed X,Y,Z: 600 mm/min - Clamping system: EROWA - C-axis measurement resolution: 0.001° - Electrode changer: 16 -fold - Electrode changer: pick-up - Electrode weight: C-axis 20 kg - max. single electrode weight: 5 kg - Electrode changer total load: 40 kg - Dielectric cooler - Dielectric filter candles: 3 pieces - Dielectric filling height: 345 mm - Dielectric capacity: 450 l - Dielectric aggregate: separate - Generator: 30 A A - Control: EROCOM 200 - Fire extinguishing system - Total power: 8 kW - Machine weight: 4400 kg - Space requirement (W x D x H): 2.2 x 3.3 x 2.4 m - Condition: very good Details tested by Maho technicians, ready for demonstration under electricity, instru ...

Knife Cortina 2600. Year of construction: 1994 Control KS 20A plasma: Hypertherm MAX 100 (cut up to 30mm) The vacuum table: 1500 x 3000 mm. With only a torch cart instead of 2 or 3, you have a working width up to 2000 mm. The box program on the PC is the OmniWin CAD. Exhaust system: Donaldson 5.5 KW To visit, now available under current Commissioning on request

52,000 litres KZE tanks/storage tanks/ sterile tanks 4 pieces UNI-BAR B. No. 19-091 A-D GL Dimensions: Diameter approx. 3,175 mm Zyl. Height approx. 5,750 mm Total height with feet approx. 7,570 mm Material: V4A, WSt. 1.4571 Containers with curved floors Wall thicknesses: underbody 5 mm, sheath 4/3/2.5 mm, upper floor 3 mm Topsoil: 1 threaded nozzle DN 80 with removable spray head, with pulled-down line NW 40 1 Venting nozzle NW 80 Cylinder: 1 manhole 350 x 450 mm swivel 1 stand display valve with scale strip and plexiglass tube 1 threaded nozzle for clear drain NW 40 1 1/2 for tasting tap 1 slanted seat flange DN 350 for agitator - without agitator - Underbody: 1 outlet pipe pulled forward DN 65 Otherwise according to sketch and photo

<b>Properties</b> Used pallet roller conveyor of the manufacturer of rack & roll GmbH Condition: Excellent condition with light wear Color: Silver Feet must be ordered separately Expertly disassembled and packed Pre-assembled on a length of 2,640 mm Including a drag reel per item Price per meter <b>Technical data Pallet roller conveyor dimensions approx.</b> Total length of an element: 2,640 mm Total width: 930 mm <b>Mass of the rollers and the frame about</b> Clamping length approx.: 835 mm Diameter approx.: 60mm Distance approx.: 150mm Material: Steel, galvanised Frame: 80x40mm Brake pulley diameter: 90 mm In stock: 140 metres <b>Pallet roller conveyor</b> Thanks to the superb craftsmanship of the pallet roller conveyor glides your material, even under high load, gently to the place of destination.  ...

52,000 litres KZE tank/ storage tank/ sterile tank UNI-BAR B. No. 19-094 GL Dimensions: Diameter approx. 3,175 mm Zyl. Height approx. 5,750 mm Total height with feet approx. 7,570 mm Material: V4A, WSt. 1.4571 Containers with curved floors Wall thicknesses: underbody 5 mm, sheath 4/3/2.5 mm, upper floor 3 mm Topsoil: 1 threaded nozzle DN 80 with removable spray head, with pulled-down line NW 40 1 Venting nozzle NW 80 Cylinder: 1 manhole 350 x 450 mm swivel 1 stand display valve with scale strip and plexiglass tube 1 threaded nozzle for clear drain NW 40 1 1/2 for tasting tap Underbody: 1 outlet pipe pulled forward DN 65 Otherwise according to sketch and photo

We sell a used Inketsystem the type 273 e incl. linear axis for the set up mark Videojet ink jet eg. on a bottling line. The unit is used and in good condition with 2 Inkjetschläuchen and applicator heads. For questions we are available under 08071104277

Technical data: -Cutting capacity 90 ° round 420 mm square 420 x 420 mm -Band saw blade dimensions 6300 x 41 x 1,3 mm -Cutting speed infinitely adjustable 0 x 130 m / min -hydr. Lifting - lowering of the column-guided saw frame - cut pressure infinitely adjustable 0-10 m / min -Hydr. movable work piece vise -biggest opening of Vice 480 mm -maximum passage height under the blade 480 mm -Material height approx. 700 mm -Total power 400 V / 8 kW -Hydr. Bundle clamping device -Coolant system -MOT. Spaeneraumbuerste -MOT. Chip conveyor - MOT feed roller 2000 mm -Space requirement approx. B 2200 x H 2500 / 2800 X 3200 mm -Weight approx. 3200 kg

Plasma and cutting installation Promotec Ector 30 / 170 Working range: 3000 mm x 17000 1 x plasma HT 2000 Hypertherm cutting up to 25mm 1 x autogen support up to 100mm To visit machine under power. Without table and filter Installation and commissioning on request

S5 - used 50m³ / 50,000 litres steel tank, double-walled, underground tank, firefighting water tank, water cistern. In good condition, underground or aboveground tank, steel storage tank, water reservoir. Surface coated with bitumen insulation / bitumen painting. capacity: approx. 50m³ / 50,000 litres material: steel tank / underground tank, double-walled manufacturer: Mannesmann dimensions: approx. Ø 2.5m x 10.0m long weight: approx. 8.0 - 10.0 tons The steel tank is used, has been emptied and professionally cleaned inside. According to the age there are traces of use. This container can serve as a storage tank for water, waste water, sewage, manure, seeping juice, rapeseed oil, or as rainwater collection tank, water cistern, firefighting water tank etc.. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your dem ...

Shredder, industrial shredder, 2 wave star breakers, glass shredder, rotor scissors, star mill, garbage shredder, two-shaft shredder, two-shaft shredder, shredder with filler for wheel loader used The shredder can also be used as a single position. Manufacturer: SANT'ANDREA NOVARA Type: G30/1570 Built in 2003 Speed of the fast wave: 17.7 rpm Speed of the slow wave 9.3 rpm Turning monent. 11875 Nm Engine VEM 22 kW 400/690 V Dimensions Shredder: approx. 2500 x 1000 x height approx. 400 mm with motor 1500 mm Dimensions of cutting unit approx. 1600 x 810 mm Throw-in height approx. 4.6 m Throw-in funnel approx. 3 x 2 m the drop-in funnel is closed by a percular upward opening slider approx. 2.5 x 1.5 m. Total dimensions of the steel construction: approx. 3 x 2 x 8 m In the shredder, used glass was broken for a foam glass bulking system. Basically, other brittle material ...

Universal - NPR-55U Stanze Knee lever punch -Punching of paper, cardboard and plastics. -for simple stamping -The cutting blades can be recorded from the shaft -The cutting blades can be created also not attached just under the pressure plate. -The pictured tools are not part of the offer.

Steel tank, used approx. 100 m³ / 100,000 litres underground tank, water tank, firefighting water tank, water cistern. In good condition, underground storage tank for horizontal placement. capacity: approx. 100 m³ / 100,000 litres material: steel tank dimensions: approx. Ø 2.9 m x 15.8 m long weight: approx. 17.0 t other: exterior with bituminous insulation or bitumen painting The tank is used and has been emptied and professionally cleaned inside. According to the age traces of use are present. It is in good condition, yet slight insulation damage caused by transport may be present on the outside. This steel tank / container can be used as a storage tank for many different media. Also we can modify the tank to suit your demands, e.g. as a fire-fighting water tank, just ask us. Price upon request. Transport can be arranged at low cost. It is not possib ...

Qty 1 x Schwabenthan 150mm dia x 350mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Even/friction selectable gear ratios, Motor mounted under frame. Complete with electrical controls and in good condition. O/a dimensions 2400 x 850mm.

100,000 litre rain water tank - rainwater cistern, underground tank for underground storage, outside with bituminous insulation - used - The container is emptied, cleaned and was factory-provided by us with a bitumen exterior painting Tank capacity: 100,000 litres / 100 m³ Length: approx. 15,750 mm Diameter: approx. 2,900 mm Weight approx. 11,600 kg Material: steel S 235 JRG 2 Delivery with our own trucks. Simply tell us the place of delivery, you will receive the exact freight costs immediately. You can visit us at every time, just let us know and we will find a suitable date! If you need any more information, just give us a call or send us an email to info@barth-tank.de. We also buy your tanks which are not needed anymore and we also accept your used tanks as a trade-in. As the European market leader, we maintain a large stock of over 3,000 above-ground and ...

Private sale Item condition: maintained Availability: immediately Coating band: yes ChocoTemper is part of the product line of the ICB Tecnologie chocolate temperature control device, with a tub capacity of 24 kg. Both machines can be equipped with vibrating table, while the coat straps for Chocotemper 24 are available • Stable stainless steel frame • Two independent motors, one for the screw and one for the agitator, for a longer life • Standard, removeable screw for easy cleaning and a quick change of chocolate • Control of the chocolate flow with pedal possible • Touchscreen control panel with various options: - Automatic dosages for a good way to do the right chocolate. - Night mode to keep the chocolate dissolved and reduce consumption during downtimes. - Counter-rotation of the screw, which is useful during cleaning The Chocotemper 24 chocolate temperature contro ...

Machine type: CNC centerless grinding machine Make/Model: MIKROSA KRONOS M SPECS CNC Fanuc 21iM grinding wheel max sizes: 250mm wide x 610mm diameter 2 controlled axis on grinding wheel dressing (interpolated) 1 axis on regulating wheel 1 axis on plunge axis (workpiece diameter) Throughfeed grinding: yes Plunge grinding: yes can be inspected under power in our warehouse in Gussago BS (Italy)