roll machine used for sale

DAUB oven THERMO-ROLL type RDTO SX02 Oven is in very good condition, General and thorough overhauled. Works like new. A good steam. Secondary circuit for the baking Chamber. Turbo equipment. incl. daub thermal oil boiler system with magnetic pump Sales including freight and installation upon request I also have to sell other model thermooel oven Price on request, Please give as oven you need type.

1 x BUZULUK 1920mm wide Four-roll 'L' calender - Type: 03506 - Rolls dia 710x1920 mm - Year of manufacture: 1989 - Peripherally drilled rolls - High pressure hot water heating (Steam 1.6 and 3.2 MPa) - Motorised nip adjustment to rolls 1, 2 and 4 (30mm adjustment) - Cross axis on roll 3 (0-30mm) - Roller Bearings - Unidrive gearbox with DC motor to each roll - Rolls 1 and 4: 46 kW - Rolls 2 and 3: 77 kW - Working speed of 4th roll max 60m/min In very good condition.

IN STORAGE - Capacity: 38 mm ? 152 mm dia. bar Length: 2.4 m ? 11.5 m 38 mm ? 216 mm dia. tube Speed: 20-180 FPM at 17° Pass line: 927 mm Rolls: 1 straight roll dia. 508 mm ? 660 mm width Roller bearings Drive: 150 HP motor, 400/1200 RPM, 250 V DC Gearbox: Total ratio 5.13:1 high 15.4:1 low sheave ratio 2:1 Dimensions: 6400 x 5530 x 184 ? L x D x H Features: Trough & pusher buggy Entry guides Total line length: 30 m

lot of 6pcs. DAUB oven THERMO-ROLL type RDTO 08.12,5.10 SX02 or 10.12,5.10 A furnace for 20 sheets Usable area of 10 m² or 12 m² 6 oven total total area 60 m² or 72 m² - 120Bleche Oven is in very excellent condition, General and thorough overhauled and tested. Works like new. Very good steam. Secondary circuit for the baking Chamber. Turbo equipment. All maagnetic pump incl. daub thermal oil boiler plant including. 40 piece rack Sales including freight and installation Price on request

Cylinder head, Bergen BRM Lower OD 430 mm, upper OD 420 mm Draw. no. 528/15-1 Reconditioned Part no: 403690 Part no: 528/15-1

Iddon Two Roll Mill 6” diam. x 12” wide Fully guarded and interlocked

Complete Line Consisting of 1.Sheet material unwind station (let off stand) 2. Iddon 1320mm x 450mm dia wide 4 roll inverted L calender manual nip adjustment, even speed gears, auto lubrication system with 45kW AC right angle drive motor and gearbox, Steam heated bowls up to 150c Bowl temperature monitoring system, fabricated bedplate. Overhauled in 2007 (by Iddon) with new side frame and rolls precision ground 3. Edge Trim - make: Mario Cotta 4. Guillotine - Make: Pasquato SNC 5. Wind up

60” x 22” Two Roll Mill Manuf.: Bridge UK With variable speed control Siemens S7 - 1200 Safety PLC. Danfoss 90kW 315 Amp Frequency Drive with Dynamic Braking Resistor Electromotor 90kW 980rpm Front Roll Speed max. speed (50Hz) 14.1rpm Manually adjustable guide plates Manual nip adjustment Failsafe Pneumatic Caliper brake for Emergency Stopping of Mill Flood cooled rolls with rotary unions fitted 8 outlet mechanical lubrication system to roll bearings David Brown gear box – ratio 980:65.1 High speed pinion / bull wheel drive to rolls Safety PLC control for Start up sequence and machine monitoring HMI fitted to main panel for status monitoring of machine Operation Controls – Rolls Stop / Rolls Start / Inch Reversetart / Inch

Qty 1 x Farrel Bridge 4 roll inverted L Lab calender, Roll width: 381 mm roll Ø: 152 mm Roller bearings Speed: 2,38 – 23,8   1/min., adjustable Nip adjustment: by hand Friction: 1:1 / 1:1,21 Drive: 9,25 kW, 380 V Measurement: ca. 1.765 x 1.687 x 1.800 mm (L x W x H) Weight: ca. 1.800 kg in. control cabinet

Stone slabs / cooker trolley for oven HEUFT VTR or Daub Thermo roll possible 2 x or 3 x deep oven width 80 cm or 100cm and how much floor you need. All for special bestelung

Berstorff Three Roll Calender Manufacturer: Krauss Maffei Berstorff 2650mm wide x 650mm (26”) diam. Effective working width 2600mm (Roller Head Die Width) Rolls Configuration: ‘I’ shape Rolls Type: Peripherally Drilled Drive: Right Hand Transmission: Direct Drive by Cardan Shafts Motors: 3X 75 KW, 2600 RPM, 50 Hz Nip Adjustment: Hydraulic (Berstorff patented) Fixed roll: Roll 2 (middle roll) Adjustable roll: Roll 1 and 3 (upper and lower roll), Max Roll gap is 80 mn Cross axis: Roll 1, 2 and 3, Hydraulic operated, max. 25 mm Pre-loading & Roll Bending: Available Rolls Speed: Variable, 0.5-10 m/ min Bearings: Antifriction Roller Bearings Electricals/ Controls: PLC Complete with motor and controls Year 2009

New venture for special order Requirements as you need all standart with daub/HEUFT 60 x 80 cm or 60x80cm sheets Stainless steel New

Buggies - HEUFT - Daub Thermo roll VTR for baking on stove. possible 2 x or 3 x deep oven width 80 cm or 100cm and how much floor you need. All for special bestelung

Baking cart - HEUFT - Daub Thermo roll VTR for baking on stove. possible 2 x or 3 x deep oven width 80 cm or 100cm and how much floor you need. All for special bestelung

Year of manufacture 2004 6 piece HEUFT VTR oven each oven with separate exhaust hood including display with digital control 2 rack are pro oven each oven is for 2 rack with 10 supports 60 x 80 cm Optionally you can buy to raetzliche rack to We have about 60 new rack with boiler with mounting with transport

Properties: Condition: fully functional, with signs of wear Ideal for fast material transport Expertly dismantled and packed Roller conveyor/ conveyor conveyor / rollers Condition: Used Manafacture: Schulz Model: Rollers Total length: approx. 15750 mm overall width: approx. 1055 mm Rollers/ conveying width: approx. 995/ 1000 mm Propulsion: Gravity Plant consists of 7 segments Segment length: approx. 2250 mm Roll diameter: approx. 50 mm Roll spacing: approx. 150 mm Material: Steel Frame height: approx. 65 mm Frame width: approx. 25 mm Includes side guide Price per meter Thanks to the excellent workmanship of the conveyor technology, your material glides smoothly to its destination, even under high loads. Tailor-made solutions for your intralogistics For roller conveyors, belt conveyors, inclined conveyors or telescopes for loading and unloading you ...

9 injection moulding tools for the production of rollers - along with a wide range of accessories As a result of a restructuring of our customer, we offer for sale 9 injection molds for the production of various types of castors for furniture and chair castors, including customer addresses. The pictures represent the basic nature of the different roles. These injection molds could be used to set up a complete production facility for the production of rolls. The basic body of the castors can then be supplemented with various inserts (depending on the customer's requirements) for final attachment to the end product, e.g. a chair. This offer also includes the following accessories - which are part of the production process: • 1 x punching tool (for the roller roller) • 1 x press (for pressing the pins and shafts) • 1 x automatic assembly machine for spring washers � ...

Bergen Rolls Royce B35:40V20AG complete gas power plant Year of Make 2011 running hours: 16.380 Hours 8415 Kw 11kV 50 Hz at 750 RPM with AVK DIG 167 f/8 alternator 9100 kvA Complete power plant with all auxilaries: Control Air Compressor ,Self Demand Transformer, LT cooling water system, cooling tower, HT cooling water system, cooling tower, cooling fans, Start Air Compressors and Air tank, Natural Gas Regulator Unit, Emergency Diesel Generator 220 kVA, piping systems oil filter and heater exchangers, Neutral Earthing Resistor Unit, Generator Cooling Fans, Steam Boiler: Nooter/Eriksen Capacity: 5.5 T/h, Switchgear Units, engine tools, instruction manual and more... Please contact for more info and complete scope / offer

82 MW Rolls Royce Trent 60 - NATURAL GAS TURBINE COMBINED CYCLE POWER PLANT -Rolls Royce USA, manufactured Trent 60 (SGT-A65) Gas Turbine Generator Set; Manufactured in 2016, delivered in August 2017 65.9 MW(e) ISO 43.8% Gross efficiency / 8,228 kJ/kWh Heat Rate DLE Dry Low Emissions with ≤ 25 ppmvd at 15% O2 on fuel gas Cold start to full power in under 10minutes 50Hz, but easily convertible to 60Hz Engine still preserved in original shipping container An aero derivative gas turbine -Siemens Steam Turbine Generator SST-300 C2S/C160; Manufactured in 2016 Output 15.75MW ISO Speed 7059 RPM Admission Steam Temperature 400 Degrees C Admission Steam Pressure 30 bara Exhaust Pressure 0.07 bara Rotation- Right

Qty 1 x Berstorff 4 roll inverted L calender, serial number: 11892-907, original year 1966 (but upgraded/refurbished in 2012), Roll sizes: 850mm dia x 2440mm wide, peripherally drilled rolls (steam/high pressure hot water heating), motorised nip adjustment, cross axis, roll bending, hydraulic preload etc. 2 speed Unidrive gearbox on universal couplings, Speed setting 1: 33.7 rpm, speed setting 2: 16.85 rpm, with 98kW DC variable speed motor fitted to each roll. Operator controls renewed recently (Siemens S7 plc) Downstream equipment: Set of 5 x cooling drums Beta thickness measuring device Edge trimming unit Menzel length cutter 3 position winder Complete and in very good condition. 2 spare rolls.

82MW ISO rated combined cycle power plant. The plant’s main equipment is composed of a Rolls Royce Trent 60 DLE Gas Turbine (also known as the SGT-A65), a Nooter/Eriksen HRSG, and a Siemens SST-300 Steam Turbine. These are below; 1. Rolls Royce USA, manufactured Trent 60 (SGT-A65) Gas Turbine Generator Set; · Manufactured in 2016, delivered in August 2017. Never used. · 65.9 MW(e) ISO · 43.8% Gross efficiency / 8,228 kJ/kWh Heat Rate · DLE Dry Low Emissions with ≤ 25 ppmvd at 15% O2 on fuel gas · Cold start to full power in under 10minutes · 50Hz, but easily convertible to 60Hz · Engine still preserved in original shipping container · An aero derivative gas turbine 2. HRSG is licensed by Nooter Eriksen USA; 3. Siemens Steam Turbine Generator SST-300 C2S/C160; · Manufactured in 2016 · Output 15.75MW ISO · Speed 7059 RPM · Admi ...

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Manual nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 106kW DC variable speed motor. Very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible coupling, 2 x 68kW DC variable speed motors. Variable friction ratio/roll speeds. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 138kW fixed speed motor. Fixed friction/roll speed. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible couplings, 2 x DC variable speed motors. Variable friction ratio and roll speed. In very good condition.

Compressor Worthington in very good condition, incl. dryer Description in the annex!

Laser-Italy, complete automatic biscuit and biscuit roll line 250-300 kg/h for: Small layer cakes, capacity: 19700 pieces/h, dimensions: 32x70xh23 mm Large layer cakes, capacity: 8900 pieces/h, dimensions: 48x100xh23 mm Mini rolls, capacity: 10300 pieces/h, dimensions: ø35x80 mm Sponge rolls, capacity 1190 pieces/h, dimensions: ø60x250 mm with 1 flow-wrapping machine 250-350 ppm (Syntegon-Germany) Includes: - Pre-mixing container for dough or baking mass PML200 - Turbo mixer aeration unit TML500 - Water cooling unit complete with connecting pipes, biscuit roll extruder, EXTR1000 - Sponge cake decorating unit before baking DECO1000 - Cyclothermal tunnel kiln FCT 1.0 x 10 m - Cooling belt for sponge cake TRPS1000 - Sponge cake work bench BLPS1000 - Longitudinal cutting device for sponge cake GRTL1000 without tools - Cutting Tools for Sponge Cake Cutter GRTL1000 - Syru ...

Qty 1 x Iddon 1320mm x 450mm dia wide 4 roll inverted L calender manual nip adjustment, even speed gears (1:1), cored rolls with rotary joints fitted, auto lubrication system with 45kW AC right angle drive variable speed motor and gearbox, fabricated bedplate. Complete with controls. Also available (if required): Sheet material unwind station (let off stand) Simple Cooling unit In-line cutter Accumulator rolls (wind up)

WDE MASPELL TVS ROLL 1.8 E 8 L vacuum kiln was built in 2015 by the Italian company WDE MASPELL S.r.l.. The machine is used for the heat treatment of solid wood, in the form of planks or pre-cut pieces with a maximum length of 8 metres. The innovative vacuum technology, compared to traditional methods of impregnating wood, reduces treatment times by up to 50%, while also reducing emissions of harmful substances into the environment. High temperature combined with vacuum improves the intrinsic properties of the wood by changing its chemical structure. As a result, the wood elements take on a very dark colour and, most importantly, become harder and more resistant to external influences, i.e. moisture or fungi. The TVS ROLL 1.8 E 8 L vacuum wood dryer is also suitable for fumigation, i.e. the process of insect removal. All thermal processes are optimised for maximum heat utilisation. Th ...

Used fermentation cabinet W&P, type: Rollmeister SC 51 -In bakery condition- El. Connection 400 V, 32 A

left with long band Machine mobile on wheels right band foldable with protective grille

4-Roll Lab Calender Inverted "L" Description attached!

Qty. 1 Second-hand overhauled 4-Hi cold rolling mill Mfc.: SUECO (Member of IHI Group) Material of rolling Series 5000 & 6000 The rolling mill has been bought in 2023 and total overhauled. All revamped and painted of mill housing, coiler, gear box, roll chock, and backup rolls etc. Installed new electrical controls, hydraulic system, work rolls and other essential components. Please note that the new owner invested USD 2.1 Million in 2023. Strip width: 400 – 600 mm (650 mm) Thickness: 0.05 – 2.0 mm Rolling speed: 300 m/min. Gear type: 3.5:1 ID 508 mm OD 1500 mm Coil weight: 5000 kg Work roll dia.: 200 mm (200 – 180 mm) Length: 740 mm Back-up roll dia.: 650 mm (650 – 630 mm) Length: 720 mm Work roll drive Main mill drive power: 300 kW, 0-600/1800 RPM R/Tension reel power: 110 kW, 0-600/1800 RPM L/Tension reel power: 90 kW, 0-600/1800 RPM

Rolls-Royce Olympus SPEED SIGNAL GENERATOR from the stock of the Army Navy Unused or overhauled

Rolls-Royce Olympus SPEED SIGNAL GENERATOR from the stock of the Army Navy Unused or overhauled

Two Roll Mill 1m wide Hydraulic Nips With motor and gearbox AEG motor, 380volts, 107amps, 55kw, 1475rpm, 50 cycles Unidrive Gearbox manuf: Santasalo, Type 3KSV70, Year 1977, Weight 1500kg Lunn Safety gear fitted front and back of Mill Complete with control panel All mounted on a one piece bedplate Compact

Key data: 30 , 13 , 1235

Compresseur WORTHINGTON CREYSSENSAC type Rollair 40 Compresseur à entrainement direct en bon état Puissance moteur : 30 KW Puisance : 40 à 150 ch Pression : de 7,5 à 13 bars Débit : de 265 à 1235 M3/H Année : 2003

Key data: 30 , 13 , 206

Compresseur WORTHINGTON CREYSSENSAC type Rollair 4000 Compresseur à entrainement direct en bon état

Two Roll Mill 42inch wide x 16inch diam. Right angle drive Brook Crompton Motor 50HP Lunn Safety Bar front and back of Mill Hand operated nips Compact

Mini roller cutter Our range now also includes machines for processing residual rolls, for example from paper production, the packaging industry, printing houses, textiles, aluminium rolls, film rolls, etc. These heavy rollers cannot be processed efficiently and safely with the normal cutting systems, but with these special "guillotine" roller cutters this is no longer a problem. The mini roller cutter can be seen here as a standard version. We offer the Mini roller cutter in version G20 / 25 and G30. All data can be customized according to the customer's wishes. (Sensors | Protective grille | Light barriers | colour, etc.) Roll width: max. 700 mm Roller height: max. 800 mm Drive: 5.5 Kw Cutting force: 25 T cylinders Weight: 1200 kg Working cycle: 65 seconds Including automatic return: Important roll cutting width and roll cutting height can be adjusted as desired. Dep ...

Weibert MKS-315 MEAL Cutting of profiles, pipes, solid materials made of black and waistband metal. saw blade diameter, 315mm bore 32mm Blade speeds 53-105 rpm Quick-release vice 140mm opening Engine power 2.2 KW Reel pad Coolant device +-45° swivel Weight 220kg WJ-MKS-315 MEAL options: underframe Circular saw blade D = 55mm 45° 50 mm material full D = 180mm 45° 80 mm pipe Square 85x85 45° 70x70mm Flat 140x70 45° 80x70mm

Strapping machine, packaging machine, strapping device, strapping set, dispenser, tape dispenser, cutting stand, vertical cutting stand -Cutting stand: vertical, mobile substructure -Cutting width: up to 1110 mm -Roll diameter. up to 660 mm -Dimensions: 760/667 / H1290 mm -Weight: 24 kg

Thread cutting head with Strehler jaws, thread cutting die, thread cutting machine, pipe thread cutter -Rollers Central ratchet lever -with: Cutting head R1 -Dimensions: 500/85/H80 mm -Weight: 2.6 kg

Three Roll Calender Manufacturer Iddon Bros. ‘I’ shape stack vertical Roll width 54” (1350mm) x 22” (550mm) diam. Even speed Rotary joints for steam heated rolls for water cooling Electrical speed controls with electric autostop Motorised roll stack at the end of the Calender Complete with gearbox, 45kW motor and starter panel The Calendar runs well and goes down to .8mm thick The Calender is mounted on a one-piece fabricated bed plate