robot used for sale

Key data: 2000 kN

Arburg 570H 2000-2100 with the Sepro Industrial Robot SDR 22S robot / Hybrid machine / Operating hours: approx. 29,000 h in automatic mode Year of construction: 2010 Injection unit: Screw diameter: 70 mm Injection weight: 984 g Spray pressure: 2000 bar Dosing volume: 1078 ccm Clamping unit : Clamping force: 200 t Tie bar spacing: 570x570 mm Size of clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: toggle lever Control: SELOGICA - Touchscreen Additional equipment: Machine in very good technical condition Hybrid machine: high-speed, energy-saving and very quiet Operating hours: approx. 29,000 h in automatic mode Euromap 67 Robot Interface Air valve x 2 Hydraulic core pull x 1 Air Core Pull x 7 Hot runner control x 15 Injection unit hardened - Bimetal Main motor of the machine - servo motor driven by inverter - energy saving The injection unit  ...

GeneralVertical Machining Centres; Control: Control F0iMF CharacteristicsTable surface1400 x 560 mmMovement X / Y / Z1100/560/510 mmSpindle taperBT 40 Tool Magazine with60 PositionsDrive power (25% DC)15 kWDrive power (100% DC)11 kWSpeed max.12000 rpmMaximum load (table centre)1000 KgRapid feed X / Y / Z36/36/30 m/minDimensions (L x W x H)3,19 x 2,76 x 2,94 (3,82 x 3,58 x 3,01) mWeight approx.5500 KgStandard spindle 12,000 min-1, 15/ 11 kWStandard Spindle 12,000 min-1, 15/ 11 kW Spindle speed: 12,000 min-1 Output: 15/13/11 kW (20/17.33/15 HP) (25%ED/30min/cont) Torque: 119/70/57 Nm (87.76/51.62/42.04 ft·lbf) (25%ED/30min/cont)Spindle Taper 7/24 Taper #40/ Grip MAS Spindle Taper 7/24 Taper #40/ Grip MAS This specification uses the spindle No. 40 7/24 taper / Grip MAS tool holder. The grip type and retention knob type of ATC are specified separately.Retention Knob: Special (Center-Throug ...

Demag Ergotech 650-5200 Model 2001 with Sülling Robot Demag Ergotech 650-5200 Model 2001 with Sülling Robot Demag Ergotech 650.5200 Model 2001 with Sülling Robot Demag Ergotech 450-1450 Model 2003 with Sülling Robot Demag Ergotech 450-1450 Model 2003 with Sülling Robot Demag Ergotech 450-1450 Model 2003 with Sülling Robot

GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose220h5 mmSpindle bore102 mmSpindle diametre on front bearing160 mmMain drive 1Drive power (100% DC)33 kWSpeed range20 - 4000 rpmTorque (100% DC)580 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)580 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Number of driven tools12 Shank diametre according to DIN 6988040 mmSpeed max.-6000 rpmPower max. (40% DC)10 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the a ...

Key data: 4200 kN

Demag Ergotech Concept 420/810-2300 with the Sepro Success 33 robot Year of construction: 2006 Injection unit: Screw diameter: 60 mm Spray weight: 800 g Injection pressure: 2420 bar Dosing volume: 891 ccm Clamping unit: Clamping force: 420 t Tie bar spacing: 800x710 mm Size of clamping plates: 1200x1100 mm Ejector: hydraulic Clamping unit: toggle lever Control: NC 4 Additional equipment: Machine in very good technical condition Euromap 67 Robot Interface Air Valve x 4 Hydraulic, needle core pull, controlled by a proportional valve - from the side of the movable plate x 2 Hydraulic, needle core pull, controlled by a proportional valve - from the side of the fixed plate x 2 Hot runner control x 18 Injection unit hardened - Bimetal Central lubrication Parallel Movements Built-in print quality control system from Sensor Kistler - tool pressure measurement  ...

Key data: 3000 kN

Wittmann Battenfeld EcoPower 300/750 / Electric machine / production line with Wittmann W821 robot and conveyor belt Year of construction: 2012 Injection unit: Screw diameter: 45 mm Spray weight: 326 g Spray pressure: 2116 bar Dosing volume: 358 ccm Clamping unit: Clamping force: 300 t Tie bar spacing: 770x720 mm Size of clamping plates: 1250x1110 mm Ejector: electric Clamping unit: toggle lever Control: UNILOG B6S - Touchscreen Additional equipment: Production line with Wittmann W821 robot and conveyor belt Electric machine: high-speed, energy-saving and very quiet Perfect technical condition Euromap 67 Robot Interface Air valve x 2 Hydraulic core pull x 1 Hot runner control x 12 Injection unit hardened - Bimetal Automatic tool height adjustment It is possible to change the screw diameter for fi 35, 40, 50 mm Robot Wittmann W821 Year of construction: ...

Key data: 800 kN

Engel e-motion 170/80 TL / New, unused production line with two robots Engel Viper 20 and Engel Viper 6 and an assembly line with optics / Electric machine Year of construction: 2020 Injection unit: Screw diameter: 30 mm Spraying weight: approx. 145 g Spray pressure: 2000 bar Dosing volume: 157 ccm Clamping unit : Clamping force: 80 t Tie bar spacing: 0x0 mm Size of clamping plates: 670x600 mm Ejector: hydraulic Clamping unit: toggle lever Control: CC 300 - Touchscreen Additional equipment: New, unused production line with two Engel Viper 20 and Engel Viper 6 robots and an assembly line with optics Tie-bar-less, electric machine: high-speed, energy-saving and very quiet Total number of operating hours: 0 h Euromap 67 Robot Interface Air Valves Air Core Pulls Control with hot runners x 20 Injection unit is wear-resistant and resistant to corrosion Central l ...

Used Robot Palletizer Fanuc 2003 The Ultimate Solution for Palletizing Operations Are you looking for a reliable and efficient robot palletizer for your business operations Look no further than the 2003 Fanuc Robot Palletizer model M 410 iB 160 Equipped with a pick up head for cardboard and available base this palletizer is designed specifically for palletizing tasks With its intelligent cable routing inside the hollow wrist high operating speeds and high inertia and wrist moments this machine can handle large grippers and heavy payloads with ease Its 6 axis control servo gripper provides better adaptability in handling products of different sizes Operating within an optimized workspace and with high vertical travel this robot can develop pallets up to a height of almost 3 meters The integrated base and controller in the pedestal or the available non pedestal version saves floor space an ...

Key data: 1500 kN

Ferromatik Milacron Magna T(MTs) 150-450 / production line with the Wemo 6-5 xDesign robot, Wemo WCS-R conveyor belt and contactor housing / machine in very good technical condition Year of construction: 2017 Injection unit: Screw diameter: 45 mm Spray weight: 215 g Injection pressure: 1984 bar Dosing volume: 226 ccm Clamping unit : Clamping force: 150 t Tie bar spacing: 510x510 mm Size of clamping plates: 740x740 mm Ejector: hydraulic Clamping unit: toggle lever Controls: B&R - Touchscreen Additional equipment: Hybrid machine: high-speed, energy-saving and very quiet Operating hours: 11,000 in automatic mode Euromap 67 Robot Interface Air valve x 1 Hydraulic core pull x 1 Hot runner controller x 36 (for additional payment) Injection unit is wear-resistant and resistant to corrosion Main motor of the machine - servo motor driven by inverter Central lubrica ...

Key data: 3000 kN

Battenfeld HM 300/2250S with the Wittmann W818 robot / Machine in very good technical condition / Operating hours: approx. 40,000 h in automatic mode Year of construction: 2007 Injection unit: Screw diameter: 55 mm Injection weight: 702.5 g Injection pressure: 2500 bar Dosing volume: 772 ccm Clamping unit: Clamping force: 300 t Tie bar spacing: 710x630 mm Size of clamping plates: 1030x1020 mm Ejector: hydraulic Clamping unit: hydraulic Control: UNILOG B6 - Touch control panel Additional equipment: Machine in very good technical condition Euromap 67 Robot Interface Control with air valve Hydraulic core pull x 1 Hot runner control x 8 Injection unit is wear-resistant and resistant to corrosion Proportional valve on the injection unit – precise injection The machine is equipped with a new original auger and cylinder Robot Wittmann W818 4-axis, high-speed ...

Key data: 1200 kN

Angel Victory 330/120 Tech / Production line with the robot Angel Viper 12 Year of construction: 2010 Injection unit: Screw diameter: 35 mm Spraying weight: approx. 140 g Spray pressure: 1595 bar Dosing volume: 154 ccm Clamping unit: Clamping force: 120 t Tie bar spacing: 0x0 mm Size of clamping plates: 740x630 mm Ejector: hydraulic Clamping unit: hydraulic Control: CC 200 - Touchscreen Additional equipment: Machine in perfect technical condition, worked in clean production Tie-bar-less, hybrid machine: high-speed, energy-saving and very quiet Euromap Robot Interface Air valve x 2 Hydraulic core pull x 2 Hot runner control x 9 Injection unit hardened - Bimetal Main motor of the machine - servo motor driven by inverter Proportional valve on the injection unit – precise injection The machine has been regularly serviced by the authorized service Engel Del ...

Key data: 1000 kN

Engel e-motion 310/100 / Electric machine / production line with the Engel ERC 13/1-F robot Year of construction: 2007 Injection unit: Screw diameter: 30 mm Injection weight: approx. 102 g Injection pressure: 2400 bar Dosing volume: 113 ccm Clamping unit: Clamping force: 100 t Tie bar spacing: 0x0 mm Size of clamping plates: 810x690 mm Ejector: electric Clamping unit: toggle lever Control: CC 200 - Touchscreen Additional equipment: Machine in perfect technical condition, worked in clean production Tie-bar-less, electric machine: high-speed, energy-saving and very quiet Euromap Robot Interface Control with air valve Hydraulic core pull x 1 Control with hot runners Injection unit hardened - Bimetal Proportional valve on the injection unit – precise injection Central lubrication The machine has been regularly serviced by the authorized service Engel Rob ...

Key data: 300 kN

Arburg 270C 300-100 with the Wittmann W621 robot Year of construction: 2005 Injection unit: Screw diameter: 25 mm Injection weight: 41 g Spray pressure: 2240 bar Dosing volume: 49 ccm Clamping unit : Clamping force: 30 t Tie bar spacing: 270x270 mm Size of clamping plates: 446x446 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA Additional equipment: Euromap 67 Euromap 12 Robot Interface Air valve x 2 Hydraulic core pull x 2 Control with hot runners Injection unit hardened - Bimetal Robot Wittmann W621 Year of construction: 2004 5-axis robots: 3 axes are driven by servo motors (electric); Axis B (rotation) and C Travels in axes: X-550, Y-1000, Z-1500 Touch control panel Robot with adapter Purchase of the robot at an additional cost Metrics: Weight: 2250 kg Length/Width/Height: 3.42x1.48x1.99 m Drive: Pumps/motor: 7.5 kW Hea ...

Key data: 500 kN

Arburg 320C 500-170 with the Wittmann W811 robot Year of construction: 12/2006 Injection unit: Screw diameter: 30 mm Spray weight: 77 g Spray pressure: 2000 bar Dosing volume: 85 ccm Clamping unit: Clamping force: 50 t Tie bar spacing: 320x320 mm Size of clamping plates: 446x446 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Euromap 67 Robot Interface Air valve x 1 Hydraulic core pull x 1 Injection unit hardened - Bimetal Proportional valve on the injection unit – precise injection Built-in sorting flap Robot Wittmann W811 Year of construction: 2010 4-axis robots: 3 axes are driven by servo motors (electric); Axis C - pneumatic Travels in axes: X-420, Y-1200, Z-1500 Touch control panel The safety package for robots Robot with adapter, protective housing Purchase of the robot at an additional co ...

Key data: 1000 kN

Arburg 470S 1000-290 / Production line with the Wittmann W821 robot / Operating hours: approx. 35,000 h in automatic mode Year of construction: 2012 Injection unit: Screw diameter: 30 mm Injection weight: 97 g Injection pressure: 2500 bar Dosing volume: 106 ccm Clamping unit: Clamping force: 100 t Tie bar spacing: 470x470 mm Size of clamping plates: 637x637 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Very good technical condition Operating hours: 35,000 h in automatic mode Euromap 67 Robot Interface Air valve x 2 Hydraulic, needle core pull, controlled by a proportional valve x 2 Control with hot runners Injection unit hardened - Bimetal Proportional valve on the injection unit – precise injection Cavity pressure sensor Priamus Robot Wittmann W821 Year of construction: 2012 5-axis robots: 4 axes ...

Key data: 1000 kN

Arburg 470H 1000-800 e² with the Wittmann W821 robot / Hybrid machine / Operating hours: 16,458 h in automatic mode Year of construction: 2015 Injection unit: Screw diameter: 55 mm Spray weight: 434 g Spray pressure: 1650 bar Dosing volume: 474 ccm Clamping unit: Clamping force: 100 t Tie bar spacing: 470x470 mm Size of clamping plates: 637x637 mm Ejector: hydraulic Clamping unit: toggle lever Control: SELOGICA - Touchscreen Additional equipment: Machine in very good technical condition Hybrid machine: high-speed, energy-saving and very quiet Operating hours: 16,458 h in automatic mode Euromap 67 Robot Interface Air valve x 2 Hydraulic core pull x 1 Control with hot runners Injection unit hardened - Bimetal Main motor of the machine - servo motor driven by inverter - energy saving The injection unit is driven by the servo motor, which is controlled by an ...

Key data: 1500 kN

Arburg 470C 1500-400 with the Wittmann W721 robot Year of construction: 12.2006 Injection unit: Screw diameter: 40 mm Spray weight: 184 g Spray pressure: 2000 bar Dosing volume: 201 ccm Clamping unit: Clamping force: 150 t Tie bar spacing: 470x470 mm Size of clamping plates: 650x650 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Euromap 67 Robot Interface Control with air valve Hydraulic core pull x 1 Injection unit hardened - Bimetal Built-in conveyor belt and sorting flap Robot Wittmann W721 Year of construction: 2006 4-axis robots: 3 axes are driven by servo motors (electric); Axis C - pneumatic Travels in axes: X-550, Y-1200, Z-3000 Touch control panel The safety package for robots Robot with adapter Purchase of the robot at an additional cost Metrics: Weight: 4900 kg Length/Width/Height: 4 ...

Key data: 2000 kN

Arburg 520C 2000-350/150 / Production line with the Wittmann W731 robot Year of construction: 2008 Injection unit: Screw diameter: 40 mm Spray weight: 166 g Spray pressure: 2120 bar Dosing volume: 182 ccm Clamping unit: Clamping force: 200 t Tie bar spacing: 520x520 mm Size of clamping plates: 728x728 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 2-Component Injection Molding Machine Very good technical condition Euromap 67 Robot Interface Air Valve x 4 Hydraulic, needle core pull, controlled by a proportional valve x 3 Control with hot runners Injection unit hardened - Bimetal Proportional valve on the vertical injection unit – precise injection Parallel Movements Screw diameter in vertical injection unit: ⌀25 mm - 49 g/hp Robot Wittmann W731 Year of construction: 2008 5-axis robots: 3 axes ar ...

Key data: 2200 kN

Arburg 570S 2200-290/100/100 / Production line with the Wittmann W843 robot / Operating hours: 23,897 h in automatic mode Year of construction: 2014 Injection unit: Screw diameter: 35 mm Injection weight: 132 g Spray pressure: 2000 bar Dosing volume: 144 ccm Clamping unit: Clamping force: 220 t Tie bar spacing: 570x570 mm Size of clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 3-component injection moulding machine, high-speed Very good technical condition Operating hours: 23,897 h in automatic mode Euromap 67 Robot Interface Air valve x 6 Hydraulic, needle core pull, controlled by a proportional valve x 4 Control with hot runners Injection unit hardened - Bimetal Proportional valve on the injection unit – precise injection Machine with two cylinders / battery with compressed  ...

Key data: 2200 kN

Arburg 570S 2200-290/100/100 / Production line with the Wittmann W823 robot / Operating hours: 20,499 h in automatic mode Year of construction: 2016 Injection unit: Screw diameter: 35 mm Injection weight: 132 g Spray pressure: 2000 bar Dosing volume: 144 ccm Clamping unit: Clamping force: 220 t Tie bar spacing: 570x570 mm Size of clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 3-component injection moulding machine, high-speed Very good technical condition Operating hours: 20,499 h in automatic mode Euromap 67 Robot Interface Air valve x 6 Hydraulic, needle core pull, controlled by a proportional valve x 4 Control with hot runners Injection unit hardened - Bimetal Proportional valve on the injection unit – precise injection Machine with two cylinders / battery with compressed  ...

Epson G10-854SR Robot Screwdriving Station Dosing Station Assembly of parts for car radios and navigation systems and for testing them. The assembly station is designed as a closed aluminium frame with a steel welding frame inserted and has a very compact design. The control cabinets and valve terminals are integrated into the system. All movement processes during the operation of the system can be tracked on all sides through large windows and doors. Operation is via a touch screen. The assembly station is divided into substations 3.1 dosing area, 3.2 assembly area KK+SW and 3.3 mounting area front. (KK=heat sink, SW=bulkhead angle) The work steps according to these assembly areas are described below: St.3.1: Dosing range - a WT with attached chassis and printed circuit boards enters the dosing area via the transfer belt. - this is stopped at the stroke positioning ...

GeneralMilling Specification; Control: Control M730UM with CELOS CharacteristicsMax machining diameter278 mmDimensions (L x W x H)2,82 x 2,09 x 2,15 mDrive power tool spindle5,5/5,5/3,7 kWDrive power main spindle11/15/15 kWRapid feed X / Z30/30 m/minInput precision of C-axis on Mainspindle0,001 degreeMovements X / Z260/590 mmRotary tool spindle speed10000 rpmNumber of tool stations12 Speed max.6000 rpmBar diameter max.52 mmSwing- Ø, max.755 mmMax. Turning Length192 mmWeight approx.4900 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and pHigh-output spindle (Left Spindle) 15/ 11 kW, 6,000 min-1(Left Spindle) High-Output Spindle 15/11 kW (20/15 HP), 6,000 min-1 The NLX ...

GeneralCNC Turning Centre with C axis and tool drive; Control: Control M730UM with CELOS CharacteristicsMax machining diameter356 mmDimensions (L x W x H)2,82 x 2,09 x 2,15 mDrive power tool spindle5,5/5,5/3,7 kWDrive power main spindle15/22/22 kWRapid feed X / Z30/30 m/minInput precision of C-axis on Mainspindle0,001 degreeMovements X / Z260/590 mmRotary tool spindle speed10000 rpmNumber of tool stations12 Speed max.-5000 rpmBar diameter max.65 mmSwing- Ø, max.755 mmMax. Turning Length510 mmWeight approx.5000 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and pHigh-output spindle (spindle 1) 22/ 15 kW, 5,000 min-1The NLX 2000 adopts a highly reliable main spindle de ...

Battenfeld HM 240 1330 2011 Battenfeld TM 400 2250 2009 We have 2 thermoset injection machine to sell. Battenfeld BCT 1800-1000 year 1994 (with Robot) Battenfeld BCT 1800-1000 year 1993 TM 27001900 BA 600200 CDC TM35001330 BA 1000 BKT THERMOSET INJECTON MACHINES Thermoset Inj. Machine- I Thermoset Inj. Machine- II With Battenfeld Robot BATTENFELD BCT 1800/100 BATTENFELD BCT 1800/100 Construction Year 1993 1994 Screw Diameter Ø60 mm Ø55 mm Clearance between tie bars 515 x 515mm 515 x 515mm Day light 1.000mm 1.000mm Working Hours 81814 h 57929 h Also: Name Battenfeld Battenfeld Type of machine HM-E 240/ 1330 INSIDER TM-E 400/2250 Control system Unilog B6E Unilog B6 Year of manufacture 2011 2009 operation hours 17 254 11 288 Cla ...

Epson C3-A601S 6-Axis Robot Assembly Station Assembly of parts for car radios and navigation systems and for testing them. The assembly station is surrounded by a protective enclosure. The service doors are equipped with interlocking monitoring switches. The doors are locked in automatic mode and can only be opened when the automazik stop or in manual mode after pressing the doors on the control panel. When the door is open, automatic operation cannot be started, the robots and servo drives of the Statioin are stopped, the pneumatic actuators are switched off and cannot be operated. This station consists of 3 functional substations: Functional sequence St.6.1: Control of ribbon cables: Lift the drive out of the chassis and tilt the drive code Control of 3 ribbon connectors by means of vision sensors on the robot gripper arm Reseat the drive in chassis St.6. ...

For sale is a used mobile/self-propelled stretch robot. The stretch robot is fully functional and in top condition. Hildebrandt laio DISC R501 = Matco EXP600 Instruction manual etc. is included. The stretching robot is characterized by its flexibility, as pallets with special dimensions/oversizes can also be adjusted. The column can be folded down for transport. A video of the robot in action can be sent on request. All prices are subject to 19% VAT.

Fully hydraulic closing system, MC 4 control system with color monitor, integrated control panel and built-in disc drive. 1 complete plasticizing system for thermoplastics with a screw diameter of 45 mm - Levels for the foundation of the Nolato machine - Hydraulic blockade of reverse rotation of the auger - Hydraulic auger drive with standard speed - SVO open nozzle in 2-piece design (nozzle body with screw-in nozzle). - A device for sorting good and defective parts. Pneumatic pendulum. Pendulum speed approx. 3 sec. Free-standing device under the machines discharge shaft. Including electrical standard connector and software (Pos. 42.42). - Single pneumatic valve on the movable mold clamping plate for the blowing function (1 piece of 3/2 separating valve with 1 magnetic coil). Control to choose between road/time or time/time. Possibility to manually set the flow using 1 thrott ...

Suitable for automatic grinding of HM circular saw blades on the chest and back in one setting. All known Tooth geometries (flat, alternate, trapezoidal, etc.) can be machined automatically and in one run. Accesories : Handling system for saw blades type ND 230 incl. data input station and 7 loading carriages,, Total enclosure,, Coolant system,, Alphanumeric slide-in keyboard for data management,, Automatic central lubrication,, Stepless variable grinding spindle drive,, Automatic fire extinguishing system,, Automatic grinding wheel measuring and compensation device, Mist extractor N182,, Oil collecting pans,, Machine lamp,, 1 sawblade holder,, 1 grinding wheel mount., Circular saw blade diameter without robot: 80-840mm, Circular saw blade diameter with robot: 100 - 630mm, Circular Saw Bore Diameter: with robot from 10 -180 mm, Sheet thickness without robots: up to 14 mm, Sheet thickness ...

Pallets Carousel for Double Wall (Twin Wall) and Filigree Floor Production, MFA M24514 Manufacturer: Vollert, Nuspl, Weckenmann, EBAWE, Filzmoser, RATEC, Unitechnik, SAA Year of construction: 2020, 2019, 2017, 2003, 1991 Control system : Siemens S7, Unitechnik Products: Twin Walls (max. height 3.0m), Filigree Floor Slabs PALLET CIRCULATION Pallets: 10.60m x 3.08m, 48 pieces STRIPPING AND LIFTING Hydraulic tilting station (EBAWE company, renewed in 2017) Lifting device for shell 1 + floor element (Weckenmann) CLEANING, PLOTTING, ROBOT-SHUTTERING AND OILING Automatic pallet cleaner, plotter, shuttering robot (Weckenmann, renewed in 2020 and 2003) STEEL REINFORCEMENT, ROBOT, WIRES, FILIGREE GIRDERS Automatic longitudinal and cross wire machine, diameter 6-14 mm, lattice girder preparation, Automatic insertion robot for laying all bars, as well as the lattice girders  ...

Key data: 1500 kN

Arburg 470C 1500-800 with the Sepro Industrial Robot 65 sprue picker Year of construction: 2021 Injection unit: Screw diameter: 50 mm Spray weight: 359 g Spray pressure: 2000 bar Dosing volume: 392 ccm Clamping unit: Clamping force: 150 t Tie bar spacing: 470x470 mm Size of clamping plates: 650x650 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Perfect technical condition, machine like new Operating hours: 7,788 h in automatic mode Euromap 67 Robot Interface Air valve x 1 Hydraulic core pull x 1 Pneumatic Core Pull x 2 Pneumatic nozzle closing valve x 2 Injection unit hardened - Bimetal Sprue Picker Sepro Industrial Robot 65 Year of construction: 2021 Purchase of the sprue picker at an additional cost It is possible to buy the machine with another robot It is possible to buy a Moretto raw materi ...

Key data: 2000 kN

Arburg 570E 2000-800 with the Sepro Industrial Robot 65 sprue picker / Electric machine / Operating hours: approx. 3,500 h in automatic mode Year of construction: 2021 Injection unit: Screw diameter: 50 mm Spray weight: 359 g Spray pressure: 2000 bar Dosing volume: 392 ccm Clamping unit: Clamping force: 200 t Tie bar spacing: 570x570 mm Size of clamping plates: 795x795 mm Ejector: electric Clamping unit: toggle lever Control: SELOGICA - Touchscreen Additional equipment: Perfect technical condition, machine like new Electric machine: high-speed, energy-saving and very quiet Operating hours: approx. 3,500 h in automatic mode Euromap 67 Robot Interface Control with air valve Hydraulic core pull x 2 Air core on solid plate side x 2 Pneumatic nozzle closing valve x 2 Injection unit hardened - Bimetal Central lubrication Parallel Movements Sprue Picker Sepr ...

Max. Laser power: 400W, operating hours: 28. 200h, with WinLas laser programming software, storage option for 99 laser programmes Optical setup for one laser light cable with fast switch (50ms switching time), optical setup can be extended to a maximum of 4 laser light cables, pilot laser with plasma sensor holder, Control of the pilot laser via laser operating software, beam guidance and shaping, LLK-B 06 laser light cable, length 40m, fibre diameter 600mm, suitable for robots, BEO 7000210p processing optics for laser welding, lens with focal length 200mm, Protective glass cassette for easy replacement of the protective glass, collimation 0° with defocussing and observation by camera, CCD camera, b/w monitor, adjustable crosshairs, camera supply cable, 30m long, and BNC video cable, 10m long, optics protection by Laval Crossjet, Design of the robot cell with suspended robot, KUKA KR 30 ...

Bosch Turbo Scara SR4 Robot + Controller MA4/200-7301-M + RH04.0S Manufacturer: Bosch Type: turbo scara SR4 PN. pressure max. 8 bar Load max. 5 kg Weight robot 40 kg + Control consisting of the following components: Rexroth / MA4/200-7301-M / Robot Controller Module Rexroth RH04.0S Swivel range / Technical data to follow Item condition used Since the article is available several times and the robots carry different working tools these are only sample pictures and may differ. (Changes and errors in the technical data, information reserved!) In addition to about 50 paternosters, countless other machines such as presses, robots, furnaces, industrial vacuum cleaners, etc. are available. Workshop equipment, workbenches, workshop trolleys, tools, forklifts and shelves abundantly available A total of 24,000 m² of production space will be dismantled  ...

Saw blade grinding machine Schmidt Tempo ECT 502 Handling with robot and 4 charging stations for neutooth and re-sharpening of HSS saw blades. With CBN deep grinding for the highest quality and cost-effectiveness and robot loading for manless grinding. 2019 technically overhauled and prepared for grinding with oil. Grinding range: 60 to 520 mm Saw blade thickness: max. 6 mm Number of teeth: 20 to 999 - Automatic charging system with industrial robot - AUTOPOS: automatic positioning of the saw blade to the grinding wheel - TEMPOTRONIC control - Special tooth shapes: 10 forms freely programmable and stored - Full encapsulation - Separate control cabinet - Data entry for batch processing via PC - Integrated halogen lamp - Automatic central lubrication - Operating instructions and operating tools

The BATTENFELD BA 600 CDC injection molding machine was built in Austria in 2002. It is equipped with Unilog B4 control. It has a closing force of 600 kN forms. The screw diameter is 33 mm and the injection volume is 99 cm3. The machine has plates for mounting injection molds with dimensions of 511 x 511 mm, and the clearance between the columns is 320 x 320 mm. The injection molding machine is equipped with a receiving robot, hot runners, a conveyor belt for collecting moldings, four pillows, a string of cores and technical documentation. Technical parameters of the BATTENFELD BA 600 CDC injection molding machine – control: Unilog B4 – dimensions of tool plates: 511 x 511 mm – clearance between columns: 320 x 320 mm – tool height, min. : 150 mm – opening path: 511 mm – injection pressure: 2022 bar – injection volume: 99 cm3 – injection weight: 90 g – screw  ...

Inv. Num. : 6484 Type: UKZ-1/305 Producer: MAVET Generated: 2017 Parameters: Power consumption: 2.49 kW Number of robot axes: 6pcs Robot reach: 1420 mm Load capacity: 12 kg Weight: 428 kg Equipment: Robot Fanuc M-10iA/12

For sale Makino 5-axis SImultan machining center type D500, equipped with a Fanuc 310iS (Profesional 5) controller including Makino robot system. Very nice 5-axis simultaneous machining center type D500. X-axis movement: 550 mm Y-axis movement: 1000 mm Z-axis movement 500 mm A-axis: 150 degrees (+30 degrees to -120 degrees) C-axis: 360 degrees continuous Complete with Makino robot system. It is a Fanuc 6-axis robot type R2000iB/165F including rack magazine Makino VIP with 45 positions

Robot KUKA KR 45/2 only mechanics ZH30/45-II Number of axles: 6 Max. load capacity: 30/45 kg Max. working range: approx. 2033 mm Year of construction: 1999 Scope of delivery: robot mechanics and connection cable 2 weeks start-up warranty. No further warranty. In addition, spare parts are always available from stock. Robot is fully functional and can be visited.

Robot KUKA KR 15/2 only mechanics ZH 15-2 Number of axles: 6 Max. load capacity: 15 kg Max. working range: approx. 1550 mm Scope of delivery : Robot mechanics and connection cable 2 weeks start-up warranty. No further warranty In addition, spare parts are always available from stock. Robot is fully functional and can be viewed

Injection molding machine efficient in operation, connected to the media, giving the opportunity to check the operation of all functions, as well as start production to verify the condition of the injection molding machine. In the years 2010-2018, the injection molding machine was equipped with a three-axis Wittmann W711 ROBOT, so the injection molding machine is 100% configured and prepared to work with a ROBOT Additional information: The Procan CT software in English or German is equipped with advanced functions for monitoring the injection process as well as monitoring all functions of the injection molding machine equipment Touch screen + quick access keypad. Interface has a built-in memory for saving programs without the need to read data from a 3.5 floppy disk. Floppy disk drive: 3.5 allows data transfer in both directions ATTENTION The injection mold and the mold mounting ...

GeneralUniversal Milling Machine; Control: CELOS with Siemens 840D sl Operate Working area 1Longitudinal650 mmCross520 mmVertical475 mmFloor space/WeightDimensions (L x W x H)2,85 x 2,35 x 2,75 mWeight approx.7500 KgTechnical DataType of main driveAC Drive power (100% DC)25 kWDrive power (40% DC)35 kWSpeed range20-20000 rpmSpindle taperHSK-63A DIN 69893 Clamping SystemDIN ISO 7388-3-A, AD Feed rate longitudinal/transverse/vertical-42000/-42000/-42000 mm/minRapid traverse longitudinal/transverse/vertical42/42/42 m/minDirect measuring systemDirect path measuring systemSpindle speed 20.000 rpmMotor spindle speedMASTER® HSK-A63 Spindle speed 20 - 20,000 min-1 Output 35 kW / 25 kW (47 hp / 33 hp) Torque 130 Nm / 86 Nm (96 ft lbs / 63 ft lbs) (40 / 100 % duty cycle)NC swivel rotary tableSwivel Rotary Table for simultaneous machining Clamping surface dia. 630 x 500mm / 24.8 x 19.6 in swivel ra ...

pressure: 100 t chamfer lenght: 3000 mm distance between columns: 2700 mm Control: AMADA AMNC II-PC throat: 415 mm stroke: 200 mm dayligth: 500 mm adjustment of the rear stops: 600 mm table width: 60 mm number of controlled axis: 7 ajustment speed: 200 mm/sec bending speed: 20 mm/sec total power requirement: 5,3 kW weight of the machine ca.: 6,7 t dimensions of the machine ca.: m Includes: -Matrix holder for 1V matrices, pluggable, total height with holder: 140mm -Status indicator light -5-axis backgauge with stop sensor system Folding robot: ASTRO-100 NT Includes: -Standard gripper -Reposition gripper on the upper press beam -Regripping support for large workpieces - pneumatically driven Technical data see PDF attachment. Handling robot: ASTRO-MP20 Includes: -Loading table with spreading magnets -Vacuum gripper Medium and Large -Combi gripper (suction/gripping) for vertical loading -Dev ...

GeneralUniversal Turning Machines; Control: Siemens 840D SL Working areaSwing diameter over guide ways330 mmSwing diameter over transverse guideway260 mmTurning diameter200 mmTransverse stroke160 mmLongitudinal stroke450 mmClamping chuck diameter max.210 mmMain drive 1Type of main driveAC Drive power (100% DC)11 kWDrive power (40% DC)16,5 kWSpeed range- 5000 rpmTorque (100% DC)112 NmWork spindleSpindle noseFlat flange Diametre of spindle nose140h5 mmSpindle bore68 mmTool holder 1Number of tool stations12 Shank diametre according to DIN 6988030 mmFloor space/WeightDimensions (L x W x H)4,47 x 2,01 x 1,75 mWeight approx.3800 KgPROGRESSlinePROGRESSline Digital Cycle-time Graphic Rest Time Product Counter12 stations servo-tool turret reception VDI 3012 stations tool turret (servo) reception VDI 30, make Sauter Note: option available only for machine in V1 versionConnection for oil mist extra ...

Robot Kawasaki RS05L E-Controller with Cab Control: E-Controller Number of axles: 6 Max. load capacity: 5 kg Max. working area: 902 mm Year of construction: 12/2012 Scope of delivery : Robot, Controller, Cable, Teachpanel, Circuit diagrams Floppy disk drive for data backup 2 weeks start-up guarantee. No further warranty. In addition, spare parts are always available from stock. Robot is fully functional and can be visited. The indicated retail price is exclusive of the statutory VAT of 19%.

CNC turning center with 6-axis Mitsubishi robot arm (robot cell) - Machine can be tested under power Specifications: Manufacturer: Mazak Model: QTG-50 SG Control: Mitsubishi M80 Year of construction: 2019 Properties: oscillation diameter: 470 mm oscillation diameter over Feed size: 100-135 mm rod diameter: 32 mm workpiece weight for shaft parts: 20 kg workpiece weight incl. chuck with suitable clamping force and stiffness of the feed: 20Kg Distance spindle nose - tool holder slide 105 to 340mm Main spindle: speed 7,000 min-¹ Min. speed 35 min-¹ Gearbox gradation Continuously variable Spindle nose H6 flat, 115 mm diameter. spindle passage 45 mm 30 min. rated power 7.5 kW B3lphazt0t TOOL REST: Tool rest type Tool holder slide Number of tools: 6 Tool dimensions (turning tool): 16x16mm Tool dimensions (drilling tool): 20 mm diameter Feed axles Rapid tr ...

Key data: 1100 kN

Demag Ergotech Multi 1100-310H/80V / Production line with the Wittmann-Demag W721 robot / Very good technical condition Year of construction: 2007 Injection unit: Screw diameter: 40 mm Spray weight: 195 g Spray pressure: 1550 bar Dosing volume: 219.8 ccm Clamping unit: Clamping force: 110 t Tie bar spacing: 470x470 mm Size of clamping plates: 670x670 mm Ejector: hydraulic Clamping unit: hydraulic Control: NC4 Additional equipment: Production line with turntable, Wittmann-Demag W721 robot, conveyor belt and protective housing 2K Machine Air Valve x 4 Hydraulic Core Pull x 2 Injection unit hardened - Bimetal Screw diameter in vertical injection unit: fi 22 mm Parallel Movements Original turntable Robot Wittmann-Demag W721 Year of construction: 2007 4-axis robots: 4 axes are driven by servo motors (electric); Axis C - pneumatic Travels in axes: X-550, Y-1 ...

Key data: 1100 kN

Engel Victory 330/110 Tech / production line with the Engel ER-HLI 41 robot and conveyor belt / machine in very good technical condition Year of construction: 2004 Injection unit: Screw diameter: 40 mm Spray weight: 190 g Injection pressure: 1670 bar Dosing volume: 201 ccm Clamping unit: Clamping force: 110 t Tie bar spacing: 0x0 mm Size of clamping plates: 790x680 mm Ejector: hydraulic Clamping unit: hydraulic Control: CC 100 Additional equipment: Production line with integrated Engel ER-HLI 41 robot and conveyor belt Tie-bar-less machine Hydraulic core pull x 1 Injection unit hardened - Bimetal Machine has been serviced by the authorized service Engel Machine with original protective housing for robot and conveyor belt Metrics: Weight: 7400 kg Length/Width/Height: 5.10x1.50x2.10 m Drive: Pumps/motor: 18.5 kW Heating capacity: 9.2 kW Total power: 2 ...

Key data: 800 kN

Krauss Maffei KM 80-180 CX with the Sepro Industrial Robot 55 sprue picker Year of construction: 2005 Injection unit: Screw diameter: 30 mm Spray weight: 77.4 g Injection pressure: 2025 bar Dosing volume: 85 ccm Clamping unit: Clamping force: 80 t Tie bar spacing: 420x420 mm Size of clamping plates: 670x670 mm Ejector: hydraulic Clamping unit: hydraulic Control: MC V - Touchscreen Additional equipment: Euromap 67 Robot Interface Control with air valve Hydraulic core pull x 1 Injection unit hardened - Bimetal Sprue Picker Sepro Industrial Robot 55 Year of construction: 2018 It is possible to buy a Moretto raw material feeding system at an additional cost The set includes: - Screw dosing unit, volumetric with container - Conveyor with proportional valve Metrics: Weight: 3900 kg Length/Width/Height: 3.80x1.50x2.10 m Drive: Pumps/motor: 15 kW Heat ...

Key data: 1300 kN

Tederic D130 with the Sepro Industrial Robot 55 sprue picker / hybrid machine / operating hours: approx. 9,500 h in automatic mode Year of construction: 2018 Injection unit: Screw diameter: 42 mm Spray weight: 246 g Spray pressure: 1900 bar Dosing volume: 270 ccm Clamping unit : Clamping force: 130 t Tie bar spacing: 420x420 mm Size of clamping plates: 620x620 mm Ejector: electric Clamping unit: toggle lever Control: KEBA - Touchscreen Additional equipment: Perfect technical condition, machine like new Hybrid machine: high-speed, energy-saving and very quiet Operating hours: approx. 9,500 h in automatic mode Euromap 67 Robot Interface Air valve x 2 Hydraulic core pull x 3 Injection unit hardened - Bimetal Main motor of the machine - servo motor driven by inverter Central lubrication Parallel Movements Sprue Picker Sepro Industrial Robot 55 Year of con ...

Used complete powder plant existing out of evaporator (4-effect, TVR), high pressure pump, spray dryer, packaging line in 25 kg bags and palletising robot., Previously used for whole milk powder (WMP). Line was running an input of ± 280.000 liters whole milk per day and an output of ± 28.000 kg of WMP per day., Still mounted inside the factory., The main components of the line:, - Evaporator, 4-effect, TVR, Manufacturer: Tebel - Van der Ploeg, Type: Falling film evaporator, Stages: 4-effect, Compression: TVR, Year: 1975, Capacity input for whole milk: ± 13.000 liter per hour (± 11,2% TS), Capacity output for whole milk: ± 3.000 kg per hour (± 48% TS), Capacity input for skim milk: ± 14.500 liter per hour (± 8,8% TS), Capacity output for skim milk: 3.000 ± liter per hour (± 48% TS), Capacity input for whey: ± 16.500 liter per hour (± 6% TS), Capacity output for whey: ± 3.000  ...