r 37 k used for sale

RAPID 4535 Granulator 3 fly 2 dead blades 2 x Screens 1 x Frame Safety system Spare set of blades

Machine type: MIG/MAG welding machine Make MERKLE Type RedMIG 3000 K Appendix No. 132.175 Connection voltage 3 x 400 volts Adjustment range 25 – 280 amps Duty cycle 35% ED at 280 amps 60% ED at 240 amps Current setting 14 switching levels Cooling transformer by built-in fan Cooling burner gas-cooled Design of mobile compact system Wire feeder 4-roller drive DV 26 Fuse 16 Ampere Dimensions L x W x H 940 x 445 x 760 mm Weight 120 kg Age 3 years Condition workshop tested, very good, incl. UVV test report Scope of supply welding system with the following accessories: 1 piece welding torch 3 mtr. long 1 piece ground cable 1 piece pressure reducer 1 roll of welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece spare parts box, complete Equipped 1 pair of welding gloves 1 Piece Instruction Manual Warranty 24 months from ...

turning diameter: 450 mm turning length: 1000 mm control: Fanuc Monforts Control F turning speeds: 45-4000 U/min chip conveyor: Tool turret 12 positions: VDI 40 swing diameter: 600 mm spindle passage: 85 mm power requirement: 37 kW total power requirement: 55 kW weight of the machine ca.: 8,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Rego Herlitzius Shop Sickle knife machine Stainless steel version mobile Manual operation via rotary control Cutting width 3 - 16mm Connection 400V, 16A-CEE plug Bread chute: 40 x 23 cm Dimensions: 1000 x 700 x 1050 mm, WxDxH Consumption machine We carry a wide range of bread slicers!

(3) Mikrosa SASL 5 CNC (size similar to Kronos M, MX, L) CNC overhaul and retrofit in progress full overhaul and CNC retrofit (pending) komplett Ueberholung + CNC retrofit Grinding wheel 500mm wide x 610mm dia. CNC 5 axis / 5 axis Mikrosa SASL 5 CNC complete overhaul and retrofit Grinding wheel 500 x 610 mm Regulating wheel 400 x 650mm Fixed center Complete mechanical overhaul Complete electrical overhaul Elimination of hydraulic movements Application CNC Siemens 840D 5 axes controlled in position with digital brushless motors: - Operating wheel axis motor with optical scale - 4 dressing axes: 2 on the grinding wheel, 2 on the regulating wheel - rotating axis with adjustable speed motor on regulating wheel - rotating axis with 55kW AC motor with inverter on grinding wheel to adjust RPM / peripheral speed (m/sec) Set-up for through-feed grinding and still customizable according to custome ...

Sheeter Kombi Rondo Doge TOP Model: SKO 611 for all doughs for rolling out and touring with program control, LED display Extendable table left, belt width 635 mm Roller opening 0.3 to 45 mm Effective pressure plate with handwheel adjustment with long roller / long mould at the bottom with tow for wrapped products Dough sheeter mobile with brakes all belts and scrapers NEW DGUV V3 tested Connection 400V, 16A-CEE plug Dimensions: 2210 x 1175 x 1383 mm, WxDxH Used machine overhauled with 6 months warranty Option: Maintenance contract E-Box Service Package More sheeters in stock!

Troughed belt continuous blasting machine Manufacturer: Rösler Drum ø: 400mm Max. workpiece length: 700/1000mm Single piece weight max. kg: 12 kg Loading capacity: 100kg Blasting wheels: 4 pieces á 7.5 kW Installed power : 45kW Warranty: 6 months functional and warranty guarantee when commissioned by DECK Sarl. Spare parts supply for the next 10 years Dlewyb OPTIONAL: Delivery to your factory Supervisor assembly / commissioning / training

The painting line is designed for varnishing elements made of MDF or HDF board. Spray booths have two circuits: one for clear coat and the other for color paint. The line is designed for water-based UV varnishes. The line consists of the following elements: - feeding table with an automatic robot from the Italian company NEOMEC - transport table with a cleaner - shower cabin from the Italian company GIARDINI DUALTECH 416 r.2017 - drying tunnel with IR lamps pcs.2 pcs - UV tunnel - roller conveyor - turntable - transport table - transport table with a cleaner - automatic painting machine - drying tunnel with IR lamps pcs.2 pcs - UV tunnel - roller conveyor - receiving table with a robot from the Italian company NEOMEC

Tube heaters Manufacturer: Ahrens & Bode Pressure-resistant up to 25 bar

Encolleuse Bürkle RCG 700 Bürkle RCG 700 2017 Find more here - /

Horizontal broaching machine RAWT 25 x 4000 x 500 company Hoffmann Year of manufacture 2000 Max. Operating pressure: 70bar, filling quantity hydraulic fluid: 630l, with loading gantry and sliding guide with carriage Find more here - /

2004 Alphatech Model RPS4000 Description: Electro-hydraulically driven frame press Series: Type:RPS 4000 Date of manufacture:12.2003 plunger force From approx. 4000 kN kN plunger force Up to approx. 916 kN kN plunger stroke approx. 600 mm Installation table - column max. 1050 mm Max. plunger rapid speed approx. 600 mm/sec Max. Splunger working speed approx. 41.7 mm/sec Max. Return speed approx. 440 mm/sec Table surface (WD) approx. 900965 mm Full volume Hydrauliko! HLP 46 approx. 5300 litres Main drive power 290 kW+ 255kW + 130kW Control voltage 230 VAC/ 24VDC Operating voltage 400 V /50 Hz Colour scheme: System RAL 1014 Control cabinet, control panel and hazard labelling RAL 2002 Find more here - / Contact us at -

Manufacturer Mathis Year of construction 2005 Roller applicator BA RRC 15004” Infrared dryer IR 5104” Find more here - / Contact us at -

IGM-Welding-Station IGM Robot Designation: Rti 330 Year of construction: 2005 1st welding unit Manufacturer: Fronius Hoist no.: 4,0750,100 Designation: Transpuls Synergie 4000 2nd welding unit Manufacturer: Fronius Hoist no.: : 4,075,097,R Designation: Transpuls Synergie 4000 Extraction system Manufacturer: Füchtenkötter Designation: FKPF 64/4 V Year of construction: 2005 Find more here - / Contact us at -

2012 Wachter Rotar 60 Back-up fuse: max. 65A Designation: Parts cleaning system E-connection 3x40v/50Hz Find more here - / Contact us at -

2012 Wächter ROTOR 60-2-Bad -- WACHTER CLEANING SYSTEMS Machine: Feeding height 9 5 0 m m Basket usable size LBH 600 x 400 x 300 mm width 1 300 mm Depth 1 600 mm Height2 200 mm ( other dimensions possible) 5. heating: Washing coils 6. drive Rhonrad: 7. belt skimmer drive 8. vapour condenser 9. Pneumatic lifting door 1 O. Automatic water level regulation 11. stainless steel basket with clamping cover VA 600x400x300mm. Mesh 6x6mm Oatum: 13.03.18 15kW 7,5kW 0,12 kW 0,04 0.45kW Basket optionally rotated, swivelled or without movement. Control system:SPS Kloeckner EASY Find more here - / Contact us at -

Resistance annealing machine This machine anneals (thermally straightens) stainless steel wires from 0.30 - 0.50mm). FUNCTIONAL DESCRIPTION: - The machine enables heating by direct passage of electric current through the wire through the wire (resistance annealing process). The device is equipped with 4 special power stabilisers for regulation, in combination with an optical pyrometer for temperature control and thermoregulation. - The simultaneous heating of the 4 wires takes place in a chamber saturated with inert gas by the electrical contact transmitted by two conductive V-shaped discs (short-circuit rollers). are transmitted. Two further V-shaped discs have the task of guiding the wires. - The system can be integrated into an existing automatic Scholl disc system, which, however, is not not included in the scope of delivery of the machine. Alternatively, the straightened  ...

2003 Reichenbacher Eco 1419 B CNC portal milling machine Year of construction 2003 Number of spindles: 8 drilling spindles Tool places: 12 Speed range: 1500-24000 rpm Find more here - / Contact us at -

3X Identical Steam Turbine sets Each steam turbine set is a complete system except the boiler for the steam generation. If sufficient water vapour is already available from another source, this can also be used. In this case, a boiler is no longer required. The three sets have never been run (like new), however, this sets are already more than 10 years old (year of production 2009). The project for which this sets were purchased has never been implemented. The steam turbine sets are running on 60 Hz. Depending on the country, where the steam turbine sets should be used, they may have to be converted to 50 Hz (replacing the gearbox and the clutch of the generator). This is possible and can be done by experienced companies. We can recommend a German company that has extensive experience in the errection and maintenance of this type of steam turbine. The unused steam turbine sets are pa ...

3x VERSATRONIC RV1s P&P machines which are slow (1200cmp/h) but full fully functional and with a lot of feeders. These machines were manufactured in a UK factory Versatronic. Machine were named Violer, Rosie and Blue. The last one is faster, little better software for fiducial camera for components. All machine are working and were used for prototype and low series like 50pcs electronic or 25pcs or 200pcs electronic. All P&P machines have two cameras, one for fiducial (up camera) and one (down camera) for components. Machines can place without problem components down to 0402 and fine pitch component like QFN or VFQFPN48… Speed for firs two is 1200cmp/h the last one is around 1500cmp/h. All machines have tool changer with 10 positions and one tool for camera auto calibration. Only 5 different tools were used but can be used up to 10 different tools. On one machine you can put u ...

2022 Diebels RMH Con Sort III Wet cutting table Technical data: Drive power [kW]: 2.6/32 CEE plug Separating area LxW [mm]: 1270 x 710 Lightweight discharge area [mm]: 1270 x 710 Number of water pipes [pcs]: 5 Number of water nozzles [pcs.]: 18 Water tank volume [litres]: 400 Electrical connection [V/A]: 400 / 32 CEE plug Weight [kg]: 750 Dimensions (without tank) LxWxH [mm]: 2500x1010x1120 Speed control in 3 stages via potentiometer on the control cabinet VA water tank with waste water pump Automatic water level control via Quick stop Operational hours: 100 hours. The separate water tank with filter was adapted by us to this system and would also be included in the sale if desired. This also applies to the table frame. Find more here - / Contact us at -

2016 HR(RUDHOLZER) Warmnietanlage Plastic welding machine Dedicated equipment for JQ specific process, machine was functional before conservation, for reuse is neccesary aditional checks and possible repair activities. Find more here - / Contact us at -

Gallus R200 (refurbished by Graficon in 2005) Label printing machine Machine definition 1 UV rotary screen + 7x UV letterpress + 1 UV flexo Rotary hot stamp unit (after 5th unit) Printing to glue / liner (2 units) 2x rotary die cutting unit Longitudial slitting Technical parameters: Max. width of material: 222 mm Max printing width: 205 mm Magnetic cylinders: 72, 78, 84, 90, 96, 132, 136 teeth Printing cylinders: 72, 78, 84, 90, 96, 103, 110, 117, 124, 132 teeth Collars for screen: 110, 117, 124, 132, 144, 156, 168 teeth Cores for hot stamp: 72, 78, 84, 96, 103, 110, 117, 124 teeth Find more here - / Contact us at -

1994 Niemeyer RWE 13 – SF 7/002 D Shaft manufacturing plant Find more here - / Contact us at -

Two group sander ideal for deburring, rounding edges and obtaining a perfect finish, thanks to the initial abrasive belt for removing excess burr and a carousel group with 8 abrasive brushes that rotate both clockwise and counterclockwise for a uniform result on the whole piece. The perfect machine for an excellent finishing quality. Independent control of the work groups via electronic touch screen panel, variable speed of the groups for a better finishing result. Table with vacuum system to guarantee the seal of the piece during processing. Quick release system for changing brushes and belt. The staggered arrangement of the brushes means allow that during the rotation the piece is always processed all over. Also suitable for processing surface treated material. Technical Specifications: - Working Width: 1350 mm - Abrasive Belt Speed: 1370 mm x 2200 mm - Abrasive Brush Dimensions: 300 ...

- Manufacturer: HAULICK+ROOS - Model : MD 260 SL - Length (mm): 0 – 260 - Material Width (mm): 10 – 260 - Material Thickness (mm): 3 - Band Speed (m/min): 60 - Band Cross-Section (mm): 800 - Year of Manufacture: 1983 The 1983 HAULICK+ROOS MD 260 SL is a mechanical double-column press manufactured by Haulick + Roos, a German company specializing in precision stamping and forming machines. This model is designed for high-speed production and is commonly used in industries requiring precise metal forming, such as automotive and electronics manufacturing. Key Specifications: - Press Force: 260 tons - Stroke Length: Variable, accommodating different production needs - Table Size: Approximately 1,250 mm x 1,000 mm - Slide Adjustment: Motorized, allowing for precise control over the slide position - Drive System: Eccentric or crank mechanism, typical for mechanical presses of this type  ...

Rippert HL9-630/1070-Bex Extraction system Type : HL9-630/1070-Bex Position : LG 0 Volume : 27,500 m³/h Pressure Increase : 3,750 Pa Density: 1.2 kg/m³ Power Input : 39.0 kW Temperature max: 40°C Temperature Medium: 40°C Motor Capacity : 45.0 kW Speed : 1,450 1/min (RPM) Max. Speed: 1,450 1/min (RPM) Special Speed: 1,450 1/min (RPM) Capacity: 100,000 m³/h Filter hoses: 462 pcs., 4190x140 mm Ø, PE – needle felt 400 g/m², antistatic, calendered, with test certificate class M, the filter hoses were only completely replaced in 12/2022 Support type: Spiral springs for hanging in tabs of the filter hoses Find more here - / Contact us at -

The Test Research Inc. (TRI) TR7550, introduced around 2010, is an Automated Optical Inspection (AOI) system designed for high-speed, inline inspection of printed circuit boards (PCBs) in electronics manufacturing. It utilizes a top-view 3-CCD color camera and four angled cameras to optimize test coverage, employing TRI´s dynamic imaging technology to minimize vibrations and provide accurate, stable inspections before and after reflow soldering processes. Key features of the TR7550 include: - High-Speed Inline Color AOI: Ensures comprehensive inspection coverage. - Precise 3-CCD Color Camera: Capable of inspecting 01005 fine-pitch components. - Advanced RGB+W Lighting System: Enhances detection of solder and markings. - Linear Motor X-Y Table: Provides vibration-free, accurate inspection. The system is suitable for inspecting various component defects such as missing components, tomb ...

Digestate Dryer - RHS Rhino Agitator Dryer - Manufacturer: RHS - Model: MCT10 - Year of Manufacture: 2018 - Power Output: 33 kW - Operating Voltage: 3-phase, 400V, 50 Hz - Control Voltage: 24V DC - Power Factor: ~0.8 (capacitive) - Frequency: 50Hz - Fuse: minimum 100A - Equipped with: Underbody cleaning on one unit, control cabinets, stainless steel feed screws, heat exchanger, heating water pump, supply air fans - Quantity: 3 units - Operating hours: approx. 7000 hours - Variants: One machine equipped with underbody cleaning Functionality The RHS Rhino Dryer is engineered for the drying and hygienization of fermentation residues (digestate) and slurry. It supports efficient moisture reduction, stabilizing the material and reducing odor. The feed system utilizes DN 150 pipelines with an eccentric screw pump, and the dried material is discharged through stainless steel feed screws for  ...

Manufacturer: FANUC Type of Machine : Welding Robot Condition: Used Find more here - / Contact us at -