punc turret used for sale

Size: A4 Technical details: Speed: 5500 Power: 380 V 1,25 KW Net Weight: 1100 KG Measurements: L1,68 x B1,24 x H1,85m Equipments: Skeleton chase: 260 x 350mm Speed min.: 2.200 sph - max. 5.500 sph Size max. 260 x 380 mm Letter Press Tiegel - DIE Cutter Punching force 40 tons Complete with tools and accessories include frame Standard chase: 260 x 340mm Machines No T 184634 H

Inv. Num. : 8405 Type: Peddimax No 1 Producer: Peddinghaus Created: 2019 Parameters: Operating hours: 150 h Strength: 140 t Pressure: 300 bar Equipment: Flaps

connected load frequency: 220 V rated current: 263/152 : 01516 81 663 694 weight of the machine ca.: 1 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Combined profile steel shear and hole punch GEKA type HYD 80 / Hydracrop 80/AMasch. No. 9566 Year of construction approx. 2000Punching force 80 ton. Projection 300 mmPunching up to 40 mm in 14 mm sheet metalFlat material shears 450 x 15 mmAngle steel shears 130 x 130 x 13 mm4 edge shears 45 x 45 mmRound material shears 45 mmRectangular clinker up to 12 mmMotor power 5.5 kWNeching connection 400 volts, 50 Hz stop with el. Stroke release 500 mm - work table with stop at the hole device 550 x 380

pressure: 40 t no. of strokes: 500 Hub/min sheet width: mm total power requirement: 5,5 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Bridge punch from Sandt with 30t

Atom cart beam punch with 25t. The machine is fully functional.

Swivel arm punch Sandt, in good condition, immediately available Robsvvhfuer Sb Nwkju If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.

Bridge punch of the company Schön, model 64035 / 92 The machine is fully functional.

Heidelberg Embossing Crucible TP, Machine Number T169693+ Heidelberg Embossing Crucible TP,T191298, Machine is in good condition, immediately available Rebevvikfer Sb Nwkju If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.

hydraulic: ja : 100 t weight of the machine ca.: 2,9 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pressure plate punch Beil 780/425-S-H-AP2; cleaned and tested; die-cut 780 and 425 mm autoplate; Investment Contact. Plate punch hatchet 780/425-S-H-AP2; cleaned and checked; punch size 780 and 425mm Autoplate; contact for plate.

Automatic Signature Punching Machine / Automatische Stanzmaschine JAMES BURN Lhermite EM 520 Baujahr / Year 1998 - Serial-No. 211661 Format Einlaufbreite / Size Infeed width 520mm Materialdicke / Thickness max. 3mm (32 pages 80 gr) Geschwindigkeit / Speed max. 10.000cycles/h Papierstärke / Paper thickness 70 to 300 gr.  James Burn Lhermite EM520 is an Automatic Signature Punching Machine.  It can be used for inline or offline production. With Feeder and Jogger delivery. The EM520 features the state of the art modular system for  punching and cutting signatures in line 

Sheet format: max. 1060 x 746 mm, min. 400 x 350 mm Equipment: Stripping station, depaneling, centerline, floor storage in depaneling station, Quick-Lock quick-release closing frame, max. machine speed 9,000 sheets/hour, max. die-cutting pressure 260 tons, processable materials: paper min. 70g/m², cardboard / solid board max. 1,000 g/m², corrugated cardboard up to 2 mm. Condition: Not operational Sale exclusively as spare parts donor Missing parts: Pumps, Grippers, Chain, Cube, Various Electrical Components Other: Machine can be visited by arrangement.

punching pressure: 16 t plate thickness: 8 mm plate length max.: 1250 mm sheet width - max.: 1000 mm engine output: 13 kW control: Cadman CNC voltage: 400 V weight of the machine ca.: 8,3 t dimensions of the machine ca.: 3600 x 2300 x 2000 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manufacturer: FINN Model: POWER LP6 Year of Manufacture: 2007 Working hours: 21,500 available : immediately Find more here - .ucymachines/ Contact us at - sales@ucymachines

Manufacturer: FINN POWER Model: LPe5 Year of Manufacture: 2002 Work area: 2500×1250 mm (+ repositioning) AVAILABLE: immediately Find more here - .ucymachines/ Contact us at - sales@ucymachines

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Single column - eccentric press WEINGARTEN type ERV 40Masch. No. 537 / 65 Year of construction 1965Compressive force 40 ton. Projection 230 mmTable size 570 x 470 mmPlunger area 250 x 200 mmClamping pin hole 40 mmInstallation height max. approx. 520 mmStroke adjustment 8 - 88 mmPlunger adjustment range 63 mmStroke rate 70 strokes per minuteDrive power 3 kWNetz connection 380 volts, 50 Hz- Table height adjustment- Overload protection by crushing plate- Clutch-brake combination by WEINGARTEN friction threaded coupling-

Single column - eccentric press WEINGARTEN type ER 63Masch. No. 52A / 63 Year of construction 1963Pressure capacity 63 ton. Projection 280 mmTable surface 630 x 530 mmAdjustable plunger stroke 8-100 mmPlunger adjustment 63 mmStroke rate 65 strokes / min. Engine power 4 kWNetz connection 380 Volt, 50 Hz- Clutch-brake combination by WEINGARTEN friction threaded clutch- Electrical stroke release via foot switch- Wheel counters- Overload protection by crushing plate- Front crankshafts Support bearingSpace requirement L x W x H 1500

Single column - eccentric press PELS - RICHTER type PEKR 125Masch. No. 20684 Year of construction 1967Compressive force 125 ton. Projection 430 mmTable size 1100 x 750 mmPlunger area 890 x 650 mmTable opening 400 mmStroke adjustment 6 to 115 mmRam adjustment 100 mmInstallation height largest stroke top max. 450 mmClamping pin bore 50 mmStroke rate 60 strokes/min. Table height above floor 900 mmMotor power 7.5 kWNerg connection 380 volts, 50 Hz- overload protection by crushing plate in the plunger- compressed air

Eccentric punching machine HAULICK + ROOS type RVD 125Double column - Eccentric pressMasch. No. 212560 Year of construction 1981Compressive force 125 ton. Table size 880 x 800 mmTable opening 470 x 140 mmStand width 900 mmStand width laterally 415 mmRam stroke 45 mmRam adjustment range 0-80 mmInstallation height in the picture 340 mmStroke rate 50 to 300 strokes/min. Engine power main drive 22 kWNe-connection 380 Volt, 50 Hz- Double connecting rod engine with 4-bearing eccentric shaft for off-center tappet pressure

Single-column eccentric press MÜLLER GEFREES type PDET 5 S/EKMasch. No. Year of manufacture 1988Compressive force 5 ton. Projection 125 mmColumn passage 170 mm Table surface 280 x 220 mmWaste height 90mmLifting area 160 x 100 mmLifting adjustment 4 to 40 mmRam adjustment 30 mmInstallation height largest stroke at the top max. 210 mmStroke rate 200 strokes/min. Clamping pin bore 25 mmTable height above floor 900 mmEngine power 0.55 kWNerg connection 380 volts, 50 Hz- pneumatic clutch-brake combination-

Single-column eccentric press WEINGARTEN type E 40Masch. No. 643/62 Year of construction 1963Pressure capacity 40 ton. Projection 250 mmTable opening 150 x 80 and 200 mmTable area 560 x 460 mmPlunger area 250 x 200 mmPlunger stroke adjustable 8-88 mmPlunger adjustment 63 mmInstallation height 320 mmPin hole 40 mmStroke rate 100/130 strokes / min. Motor power 2.2 / 3 kWNetz connection 400 volts, 50 HzTable height above floor 840 mm- Clutch-brake combination by WEINGARTEN friction threaded coupling with TDC

Hydraulic punch, punching rack for the use of punching units JOKA type HP-SHydraulic hole punch, hydraulic press for punching bracketYear of construction approx. 1995Printing capacity 5 ton. Projection 155 mmStroke approx. 20 mmPunching unit width max. 54 mmPunching unit height max. 220 mmDie holder 48 mmMotor power 1.5 kWNeching connection 230 volts, 50 Hz- for the universal use of punching units JOKA SW 20 or SWD 20- Projection of the punching units can be larger, can be pushed through to the rear- Stroke release via

A punch riveting tool Böllhoff is available. Documentation available. An on-site inspection is possible.

Key data: 75 t, 80 mm, 120 1/min

Pressure 75 t Stroke rate 120-600 / min Sheet width 10-300 mm Table size 1050 x 820 mm Pusher clamping surface 960x820 mm Distance table - UK plunger 380 mm Adjustable stroke - max. 80 mm Feed length 0-150 mm Total power requirement 20 kW Machine weight approx. 13 t Feed unit with max. belt speed 70 m/min Eccentric shaft with 4-fold bearings 2 connecting rods Central lubrication incl. magnetic belt conveyor - in use until 2020 -Operating instructions -Manual - Circuit diagram etc..

A cylinder roll punching machine Adolf Illig is available. Pass-through width: approx. 850mm, pass-through height: approx. 120mm, roll diameter: approx. 190mm, table dimensions X/Y/Z: 2x approx. 1200mm/1200mm, working height: approx. 800mm, machine dimensions X/Y/Z: approx. 2700mm/1350mm/1550mm, weight: approx. 900kg. An on-site inspection is possible.

Amada punching machine EMK 3610NT incl. loading unit MP300 for sale. We would like to hand over the machine complete with tools and Wilson X-Sharp grinding machine.

A brought cylinder Heidelberg 40x58cm

Inv. Num. : 5955 Type: Trumatic 500 R Producer: Trumpf Created: 2003 Parameters: Control system: TRUMAGRAPH CC 220 S Switch-on hours: 29433 h Compressive force: 22 t Machine height: 2200 mm Machine length: 6900 mm Machine width: 5800 mm Machine weight: 11000 kg 2020: Replacement of hydraulic hoses

Max. punching force: 500kN, max. punching stroke: 200mm, max. punching area: 1800x750mm, connected load: 39kVA, length: 6500mm, width: 3900mm, height: 2900mm, net/operating weight: 7.8/10.2t, operating hours: 56,645h, with documentation. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

Punching force: 500kN, throat depth: 610mm, stroke: 60mm, max. hole diameter in steel thicknesses 15mm/9mm/4.5mm: 30mm/50mm/100mm, max. material thickness: 15mm. Machine dimensions X/Y/Z: approx. 1100mm/1550mm/1750mm, weight: approx. 1650kg. An on-site inspection is possible.

Max. punching force: 300kN, max. punching stroke: 200mm, max. punching area: 1800x750mm, connected load: 11kVA, length: 4800mm, width: 3400mm, height: 2800mm, net/operating weight: 10/13t, operating hours: 2818h, with documentation. The control was renewed in 2022. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

pressure: 25 t no. of strokes: 1500 Hub/min sheet width: mm total power requirement: 20 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. punching force: 500kN, max. punching stroke: 200mm, die support dimensions: 13,200x1500mm, conveyor belt dimensions: 7435x1995mm, max. punching area: 1800x750mm, max. strokes: 80/min, connected load: 34kVA, length: 6500mm, width: 3900mm, height: 2900mm, net/operating weight: 7.8/10.2t, operating hours: 52,680h, with documentation. Equipped with extraction system, rotatable tool enabling nesting, tension-free unwinding possible. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

pressure: 25 t no. of strokes: 1500 Hub/min sheet width: mm total power requirement: 20 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

740 x 1,050 mm max. / 330 x 480 min. Size MABEG Scale Layer Flatbed die-cutter Punching force 1.8 MN / approx. 182 t HFS Hot Foil System Feeder stack 115 cm Display stack 85 cm Total meter approx. 12 million

Punching force: 300 kN For example, punches a 20 mm hole in 12 mm steel Stroke release via foot switch Range of tools is included in the price

Punching force 45 t. 2 pcs. available from stock (Video under power on request)

Width 34 cm Year of construction 2000 electric punching and binding machine Electric Punching - Manual Tying Split 3:1 Table model Delivery date: short-term Price on request. We supply and install worldwide.

Inv. Num. : 8689 Type: SBL-1050SE Producer: SABRE Created: 1994 Parameters: Maximum format size: 1050 x 750 mm Minimum format size: 400 x 370 mm Maximum workpiece thickness: 0.1-2 mm Impact pressure: 300 t Service ramp dimensions: 3282 x 1740 mm Length: 5573 mm Height: 2025 mm Width: 2111 mm

Punching force: 300kN, max. operating pressure: 300bar, weight: 13500kg, operating hours: approx. 52300h. Documentation available. An on-site inspection is possible.

Make: TRUMPF Type: TRUMATIC 2000R Year of Make: 2001 Working area: 1270 x 1270 mm Punching force: 18 tons Max. sheet thickness: 6.4 mm Max. workpiece weight: 75 kg Max. punching diameter: 76 mm Max. speeds: 90/60/108 m/min Accuracy: +/- 0.1 mm Length: 5100 mm Width: 5800 mm Height: 2070 mm Weight: 9200 kg Accessories: TOPS 2000 CAM software, tool holder, Very good condition, only thin sheets