pu foam used for sale

Double diaphragm pump with compressed air drive DEPA type DH50-FA-ZRTDoduct diaphragm pump, double pumpSeries No.: B1600416 year of construction 26.01.2016Temperature: max. 130CBausize: 50Grain size: max. 18 mmSuction height: approx. 2 mSuction height product filled: approx. 9 mOperating pressure: max. 7 barAir connection: 3/4Suction connection: 2Pressure connection: 2- self-priming- Aluminium housing- Diaphragm plate made of stainless steel- Diaphragm made of nopped E4® PTFE Composite balls made of PTFE- Ball seats made of stainless steelSpace required: L x W x H 550 x 350 x

Mechanical pull-down NC Machine vise FRIBOSA Type Size BPrision machine vice, grinding vice, clampJaw width 100 mmJaw height 34 mmWingspan 0 to 130 mmGuideway height 40 mmGuideway length 270 mm- Mechanical machine vice- Clamping area via trapezoidal spindle- Stable base body ground on all sides- Can be clamped horizontally, vertically or laterallyDimensions L x W x H 310 x 100 x 77 mmWeight: 10 kgGood condition; used

Single-column eccentric press WEINGARTEN type E 40Masch. No. 643/62 Year of construction 1963Pressure capacity 40 ton. Projection 250 mmTable opening 150 x 80 and 200 mmTable area 560 x 460 mmPlunger area 250 x 200 mmPlunger stroke adjustable 8-88 mmPlunger adjustment 63 mmInstallation height 320 mmPin hole 40 mmStroke rate 100/130 strokes / min. Motor power 2.2 / 3 kWNetz connection 400 volts, 50 HzTable height above floor 840 mm- Clutch-brake combination by WEINGARTEN friction threaded coupling with TDC

Hydraulic punch, punching rack for the use of punching units JOKA type HP-SHydraulic hole punch, hydraulic press for punching bracketYear of construction approx. 1995Printing capacity 5 ton. Projection 155 mmStroke approx. 20 mmPunching unit width max. 54 mmPunching unit height max. 220 mmDie holder 48 mmMotor power 1.5 kWNeching connection 230 volts, 50 Hz- for the universal use of punching units JOKA SW 20 or SWD 20- Projection of the punching units can be larger, can be pushed through to the rear- Stroke release via

Crane Motor, Travel Drive Crane Bridge Drive with GearSliding Armature Motor, Thrust Bencher Motor, Three-Phase Electric Motor, Brake Motor, Crane Motor, Rope Hoist Drive, Crane Drive, Lifting Motor, Fine Stroke MotorManufacturer: DEMAGMotor Type: 24/10 KF8-2Motor No.: 982869Motor Design: B5Rated Voltage: 380 VAC Rated Frequency: 50 HzPower Level 1: 0.58 kW = 715 rpm. Power level 2: 2.3 kW = 2900 rpm.with gearbox DEMAG type KS 12Reduction gearboxFabr. No. 1909104Translation: i = 118with impeller for crane rail2 pieces available,

A complete punching system with a grid punch is available. 1) Double reversible decoiler, load capacity: 1000kg. 2) Alba GGVHY 200 straightening machine, year of manufacture: 1992, feed rate: 6.5m/min, max. material width: 200mm, max. material thickness: 4mm, transport rollers: 2. 3) Alba MA RIA 7 feed, year of manufacture: 1978, max. material width: 300mm, max. material thickness: 3mm, feed rate: 40m/min, control: Siemens S7. Material thickness: 3mm, feed speed: 40m/min, control: Siemens S7 with OP7. 4) Punching machine Raster HR 80/700 NL, year of manufacture: 1992, pressing force: 80t, stroke rate: 250/min, table dimensions X/Y: 730mm/750mm, ram dimensions X/Y: 730mm/630mm, ram stroke: 40mm, ram adjustment: 80mm. 5) Profiling machine CIS. Documentation available. On-site inspection is possible.

A complete punching system with a grid punch is available. 1) Reel Gebrüder Kemmerich 7VID, year of manufacture: 1981, max. load: 1000kg. 2) Straightening machine, max. material width: 300mm, max. material thickness: 2mm. 3) Feed unit Alba UVHY 300/0.1, feed speed: 6.5m/min, max. material width: 300mm, max. material thickness: 4mm, transport rollers: 2. 4) Punching grid HR 50/600 NL, stroke rate: 300/min, stroke: 30mm-80mm. On-site inspection is possible.

Max. saw blade diameter: 520 mm Cutting height: 200 mm at 90°, 140 mm at 45° Cutting length: 420 mm Mitre range horizontal: 45°-90°-25° Mitre range vertical: 60°-90°-30° Pneumatic material tensioners Minimum quantity spraying device Powerful 5 KW motor

High Pressure Pump HP-K-25-56 Volume:19.8 m³/h Pressure:10 MPa Stroke rate:435 1/min Oil volume:6 dm³

Pump with substructure and drive Min. Max. Flow rate 4 m³/h 35 m³/h Differential pressure 14.9 bar 3.9 bar Joint type: K (arch tooth joint) Joint seal: Protective sleeve screwed Joint seal: material EPDM, sleeve inside FPM Joint Lubrication Food Oil UH1 6-460 Rotor material: CrNiMo17-12-2 Rotor: Temperature range 80°C undersize Stator Material: NEMOLAST® S46 Special version m.STP2 Stator Bolt Material: Galvanized Steel Accessories mounted on the pump STP-2 without temperature controller Geared Motor North, Type SK52-180MP/4

Pump with substructure and drive Flow rate min. 10 m³/h max. 70 m³/h Differential pressure min. 4.9 bar max. 0.9 bar Joint type: K (arch tooth joint) Joint seal: Protective sleeve screwed Joint seal: material EPDM, sleeve inside FPM Joint Lubrication Food Oil UH1 6-460 Rotor material: CrNiMo17-12-2 Rotor: Temperature range 80°C undersize Stator Material: NEMOLAST® S46 Stator Bolt Material: Galvanized Steel Geared Motor North, Type SK52-160LP/4-F(VL) TF F

Key data: 75 t, 80 mm, 120 1/min

Pressure 75 t Stroke rate 120-600 / min Sheet width 10-300 mm Table size 1050 x 820 mm Pusher clamping surface 960x820 mm Distance table - UK plunger 380 mm Adjustable stroke - max. 80 mm Feed length 0-150 mm Total power requirement 20 kW Machine weight approx. 13 t Feed unit with max. belt speed 70 m/min Eccentric shaft with 4-fold bearings 2 connecting rods Central lubrication incl. magnetic belt conveyor - in use until 2020 -Operating instructions -Manual - Circuit diagram etc..

Progressing cavity pump with substructure and drive Flow rate min. 4 m³/h max. 35 m³/h Differential pressure min. 14.9 bar max. 3.9 bar Joint Type: Bolt Joint Joint seal material: EPDM/1.4401 Joint Lubrication: Food Oil UH1 6-460 Rotor material: CrNiMo17-12-2 Rotor: Temperature range 80°C undersize Stator Material: NEMOLAST® S46 Special version m.STP2 Geared Motor North, Type SK52-180MP/4 -F(VL) TF

A cylinder roll punching machine Adolf Illig is available. Pass-through width: approx. 850mm, pass-through height: approx. 120mm, roll diameter: approx. 190mm, table dimensions X/Y/Z: 2x approx. 1200mm/1200mm, working height: approx. 800mm, machine dimensions X/Y/Z: approx. 2700mm/1350mm/1550mm, weight: approx. 900kg. An on-site inspection is possible.

BWT VT2000 Pure steam generator Serial: V16010 2016, BTW Vapotron VT2000, max output 2200 Kg/hour steam, with Elmo Rietschle vac pump, all mounted on stainless skid, two in stock

1 of used vacuum pump, make DVP Vacuum Technology srl, Type: SB.16 9801024, SN: 1207491, Prod. 2012, KG: 27,5, Flow rate 50(60) Hz: 16 (19), Final pressure: 120 mbar (hPa). Driven by motor CSM Motori Srl,, Type M80A4 TROP, SN: 050802281, 50 Hz.: 220/380 or 255/440V, 60 Hz.: 220/380 or 266/460V. Cleaned, new filter and vanes fitted, tested OK. Twoo virtually identical pumps available.

Make Becker, Type: VT 4.16, SN: 2409570, 50/60 Hz., 1420/1700 /min, 0550,70 kW, 16/19 m3/h, 150/150 mbar. New 2009. Cleaned, fitted with new filter and tested OK.

A punch riveting tool Böllhoff is available. Documentation available. An on-site inspection is possible.

Mueller P7505 Pure steam generator Serial: 394131-1 2009, Stainless steam generator, 5700Kgs per hour, Allen Bradley touch screen controls, two in stock, 3Ph

Amada punching machine EMK 3610NT incl. loading unit MP300 for sale. We would like to hand over the machine complete with tools and Wilson X-Sharp grinding machine.

Dosing pump with 90 l/h flow rate Properties: Length 370 mm Width 200 mm Total height 430 mm Volume 90 L Engine power 0.43 kW Manufacturer: LEWA ecodos Manufacturer Serial No. EEK 0090 S11

System to sterilize water by using UV-rays.

Inverter heat pumps / chiller air-cooled reversible, Type: iHCY 020 PT1+FSH MTA S.p.A. HCYGNUS TECH Inverter iHCY 020 PT1+FSH are compact heat pumps reversible (heating / cooling) that are suitable for outdoor installation up to -15 / -10°C suction temperature. Including crank pan heater, buffer tank, built-in P1 circulation pump, electric antifreeze heater (evaporator, storage tank and pump) and inverter scroll compressors Heat output kW 6.43 Heating water temp. Exit/inlet: 45 / 40°C Volume flow m³/h 1.13 Available pump pressure bar: 0.84 Ambient temperature °C +7 Cooling capacity kW 5.46 Cold water temp. Exit/Entry: 7 / 12°C Volume flow m³/h 0.971 Available pump pressure bar: 0.893 Ambient temperature °C 32 Refrigerant R 410A Electrical data: Voltage V 400, Frequency Hz 50, Phase Ph 3 Max. power consumption (kW) 3.06 Max. current (A) 11.43 Starting C ...

Inverter heat pumps / chiller air-cooled reversible, Type: iHCY 020 PT1+FSH MTA S.p.A. HCYGNUS TECH Inverter iHCY 020 PT1+FSH are compact heat pumps reversible (heating / cooling) that are suitable for outdoor installation up to -15 / -10°C suction temperature. Including crank pan heater, buffer tank, built-in P1 circulation pump, electric antifreeze heater (evaporator, storage tank and pump) and inverter scroll compressors Heat output kW 6.43 Heating water temp. Exit/inlet: 45 / 40°C Volume flow m³/h 1.13 Available pump pressure bar: 0.84 Ambient temperature °C +7 Cooling capacity kW 5.46 Cold water temp. Exit/Entry: 7 / 12°C Volume flow m³/h 0.971 Available pump pressure bar: 0.893 Ambient temperature °C 32 Refrigerant R 410A Electrical data: Voltage V 400, Frequency Hz 50, Phase Ph 3 Max. power consumption (kW) 3.06 Max. current (A) 11.43 Starting C ...

Plunger Pump, High Pressure Pump, Homogenizer, Plumger Piston Pump, Plunger Piston Pump Manufacturer: WOMA Apparatebau GmbH Type: 753.50 max pressure 150 bar Flow rate approx. 175 l/min Engine Power: 55 kW 1500 rpm 380/660 volts 50 Hz Dimensions approx. 1800 x 1000 x 750 mm

Corner forming machine

max. format 54 x 72 cm Built in 1960 Inking unit not complete for punching / embossing Price on request. We supply and install worldwide.

Roller conveyors with chains pull 90° RA1846 Type: Transnorm 3300-600-550 Length: FL = 3300 mm Conveyor width: FB = 550 mm Total width: 600 mm The chains off slide width: 700 mm height (BH): 140 mm Support roller pitch: 80 mm including pneumatic stopper Optionally available: Supports Side guide one and both sides frequency inverter Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: KW: 0,37/S1 Engine type: Bremse, SEW Eurodrive angle: 90° Nominal / outside width in mm: 600 Roll width in mm: 550 Roll division in mm: 80 Conveying length in mm (NL): 3300 Bauhöhe in mm (BH): 140 Electric data: 230, 400 For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your tea ...

A brought cylinder Heidelberg 40x58cm

Offer 25269 PVC – Gas Strip Sawing Machine Specifications: - Saw blade speed frequency-controlled for very fine sawing - Saw blade diameter 200 mm -Auto. Workflow - Press stop with SICO counter to adjust the glass contact pressure - -simulation - Pneumatic connection 6 bar - Drive 400 V / 0.8 kW - Space requirement approx. W 400 x H 1200 x D 700 mm - Weight approx. 80 kg - Machine stand

Following Lub Oil Pump of MAK ENGINE is available for sale. Make ZPM GMBH Type WD5/WDU5-2-F Nr. 10010/6/2/2008 N 2000 1/min Q 685/780 L/min Bar 8/3

A dosing pump (ointment pump) Viscotec for highly viscous liquids is available. Dosing range: 1µl-1l, dosing precision: +/-1%, repeat accuracy: over 99%, flow range: 0.2ml-700ml/min. Including control system and spare parts package. An on-site inspection is possible.

Inv. Num. : 5955 Type: Trumatic 500 R Producer: Trumpf Created: 2003 Parameters: Control system: TRUMAGRAPH CC 220 S Switch-on hours: 29433 h Compressive force: 22 t Machine height: 2200 mm Machine length: 6900 mm Machine width: 5800 mm Machine weight: 11000 kg 2020: Replacement of hydraulic hoses

Used machine, Woma / Kärcher Ecotherm, hot water Working pressure: 500 bar flow 27 lpm, Year of construction 2009 Drive: Diesel 36.5 kW, Kubota V 2403 Diesel Operating hours: approx.: 645 h,

Max. punching force: 500kN, max. punching stroke: 200mm, max. punching area: 1800x750mm, connected load: 39kVA, length: 6500mm, width: 3900mm, height: 2900mm, net/operating weight: 7.8/10.2t, operating hours: 56,645h, with documentation. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

2x Fristam FKFS40 Lobe pump - 2,2 kW - Small difference in the delay between the pumps - Excellent condition

Max. punching force: 300kN, max. punching stroke: 200mm, max. punching area: 1800x750mm, connected load: 11kVA, length: 4800mm, width: 3400mm, height: 2800mm, net/operating weight: 10/13t, operating hours: 2818h, with documentation. The control was renewed in 2022. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

Gabarino MU80-250 Pump Ship Condition see photos Pump unused Electric motor overhauled

Max. punching force: 500kN, max. punching stroke: 200mm, die support dimensions: 13,200x1500mm, conveyor belt dimensions: 7435x1995mm, max. punching area: 1800x750mm, max. strokes: 80/min, connected load: 34kVA, length: 6500mm, width: 3900mm, height: 2900mm, net/operating weight: 7.8/10.2t, operating hours: 52,680h, with documentation. Equipped with extraction system, rotatable tool enabling nesting, tension-free unwinding possible. The machine has been regularly maintained, hydraulic unit integrated into the machine frame, with PC control. An on-site inspection is possible.

Features: automatic non-stop delivery with conveyor, non-stop feeder with rods, pull mark left, push mark right, quick clamping frame for tooling, lower stripping station, upper stripping station, two exchange frames for lower stripping station. Without die-cutting plates. Processable materials: min. paper 90g/m², max. solid board 2000g/m², max. corrugated board/ with MasterSet 4/ 2mm, max. sheet size 760x1060mm, min. sheet size/with MasterSet 300x350/ 350x400mm, max. cutting pressure: 2.6MN/ 260t, max. machine speed: 8000 sheets/h, max. feeder pile height without non-stop/ in non-stop operation: 1500/ 1200mm, max. feeder pile weight: 1500kg, max. delivery pile height: 1400mm, max. delivery pile weight: 900/ 1340kg. Operating hours: 1525h. An on-site inspection is possible.

Met elektrische achteraanslag Ponscapaciteit: 70 ton Dia x plaatdikte: Ø 28 x 20 mm Maximale slag: 80 mm 40 str / min Keeldiepte: 300 mm Werkhoogte: 1065 mm Maximale snijdikte in plaat: 20 mm Bladlengte: 455 mm 90°-snede: 130 x 130 x 13 mm 45°-snede: 90 x 90 x 10 mm Op maat gesneden rond/vierkant: 45 mm Elektromotor (vermogen): 7,5 kW Lengte: 1800 mm Diepte: 1200 mm Hoogte: 2000 mm Gewicht: 1650 kg

Height=1 m, Overall length= 0.85 m, Overall width= 1.35 m,

Height=0.48 m, Overall length= 0.57 m, Overall width= 1.18 m, Net weight= 218 kg,

Height=0.45 m, Overall length= 0.55 m, Overall width= 1.1 m,

Height=0.45 m, Overall length= 0.54 m, Overall width= 0.98 m, Net weight= 190 kg,

Height=0.45 m, Overall length= 0.5 m, Overall width= 0.7 m,