133,852 used machines on RESALE, but how to find them? Machine Search
Combined profile steel shear and hole punch GEKA type HYD 80 / Hydracrop 80/AMasch. No. 9566 Year of construction approx. 2000Punching force 80 ton. Projection 300 mmPunching up to 40 mm in 14 mm sheet metalFlat material shears 450 x 15 mmAngle steel shears 130 x 130 x 13 mm4 edge shears 45 x 45 mmRound material shears 45 mmRectangular clinker up to 12 mmMotor power 5.5 kWNeching connection 400 volts, 50 Hz stop with el. Stroke release 500 mm - work table with stop at the hole device 550 x 380
A Drinns flywheel eccentric punching machine is available. Pressing force: 250kN, ram table distance: 230mm, stroke adjustment: 10mm-65mm, number of strokes: 145 strokes/min, flywheel speed: 145rpm, max. tool weight: 190kg, machine weight: approx. 2250kg. Documentation available. On-site inspection is possible.
An HMS punching machine is available. Pressing force: 250t, stroke height: 40mm, installation height: 450mm, ram adjustment: 20mm, stroke rate: 120 strokes/min, overall system dimensions X/Y/Z: approx. 17000mm/8000mm/3500mm. Including coil and strip processing. Documentation available. On-site inspection is possible. Expected to be available from September 2025.
A laser cutting and punching machine Trumpf with an unknown defect (linear amplifier in order) is available. Press force: 220kN, laser power: 1500W (1.5kW), max. punching diameter: 76mm, max. workpiece dimensions X/Y: 2585mm/1280mm, max. sheet thickness mild steel/stainless steel/aluminum: 8mm/6mm/4mm, max. workpiece weight: 200kg, part dispenser X/Y: 500mm/500mm, magazine positions: 18, machine dimensions X/Y/Z: approx. 8000mm/7500mm/2400mm, weight: approx. 16000kg. On-site inspection is possible.
connected load frequency: 220 V rated current: 263/152 : 01516 81 663 694 weight of the machine ca.: 1 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting width: 150 mm machine weight ab.: 300 kg : 27468 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
centre distance: 1200 mm : 550 weight of the machine ca.: 2,5 t multifix: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 t no. of strokes: 40 - 120 Hub/min sheet width: mm total power requirement: 40 kW Pressing capacity 160 ton Table clamping area 1,100 x 1,280 mm Ram clamping area 850 x 890 mm Distance between guides 1,120 mm Distance between columns (below guide ways) 1,350 mm Distance between Table and ram in upper position approx. 400 mm No. of strokes 40 - 120 /min Adjustment of stoke 67 / 115 / 160 mm Ram adjustment, motor driven 125 mm Ejector travel 50 mm Total electrical load, approx. 40 kW - 500 V - 50 Hz Weight, approx. 24,000 kg Accessories / Special Features WEINGARTEN Sheet Metal Uncoiler with overhead loop control (space saving because it does not need a loop-pit). Strip width 375 mm. The loop control guides the strip-material from the uncoiler to the machine thru a straightening device with automatic supervision. 8-track slide bearing guide. Automatic oil-circulation lubr ...
turning diameter over bed: 410 mm turning diameter over slide rest: 240 mm turning length: 1000 mm turning diameter in the gap: 530 mm turning speeds: 65 - 1810 U/min centre height: 205 mm spindle bore: 52 mm tailstock quill taper MT: 4 total power requirement: 2,2 kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1,9 x 0,8 x 1,3 m Center lathe with: 3-axis digital measuring system fully assembled electromagnetic main spindle brake auto. Feed in longitudinal and transverse direction safety relay Micrometer end stop coolant device 3-jaw lathe chuck with 1 set of turning and drilling jaws German operating instructions. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 400 mm turning diameter over slide rest: 264 mm turning length: 1000 mm turning diameter in the gap: 550 mm turning speeds: 44 - 2000 U/min centre height: 200 mm spindle bore: 52 mm tailstock quill taper MT: 4 MK connected load frequency: 400 V total power requirement: 1,5 / 2,4 kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1,9 x 0,8 x 1,56 m 3-axis digital display 3-jaw chuck 200 mm. 4-jaw chuck 200 mm. Faceplate 320mm bezel fixed running bezel 4-fold steel holder. Halogen machine light machine light foot brake removable chip tray, chip protection wall Hardened and ground bed tracks Complete coolant system lining protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 320 mm turning diameter over slide rest: 200 mm turning length: 900 mm turning diameter in the gap: 320 mm turning speeds: 75 - 2000 U/min centre height: 160 mm spindle bore: 38 mm tailstock quill taper MT: 3 connected load frequency: 400 V total power requirement: 1,5 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 1,6 x 0,75 x 1,7 m SINO digital display 3-jaw chuck 200 mm. 4-jaw chuck 200 mm. Faceplate 250mm bezel fixed Quick-change steel holder with 4 pcs. steel holder machine light Chip tray, chip protection wall Hardened and ground bed tracks lining protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Suitable for chamfering and surface grinding of hard metal rods. Accessories: Full cladding, Wet grinding device, Loading magazine for workpieces from 30 - 150 mm, Hydraulic feed of the grinding head, Hydraulic feed of the workpiece spindle head, Hydraulic workpiece clamping of the cylindrical grinding device, Preparation for connecting an extraction system, Automatic fire extinguishing device, Touch panel TP 177 A., workpiece diameter automatic mode: 3 - 20 mm, workpiece diameter semi-automatically: 3-32mm, workpiece length semi-automatic: 3-32mm, workpiece length: 30-150 mm, Drive power grinding spindle: 4.0 kW, Spindle speed grinding spindle: 2000 rpm,, speed of the cylindrical grinder: 1500 rpm., cutting wheel diameter: Max. 200 mm, Electrical connection: approx. 7 kW (400 V / 50 Hz), Dimensions L x W x H: 2000 x 1500 x 1500 mm, mass: approx. 1,600 kg, colour: gray RAL 7035, Dimensio ...
Two Illig punching machines are available for the precise punching of thermoformed plastic parts from film material. Working width: approx. 900mm, working height: approx. 120mm, roller diameter: approx. 196mm, machine dimensions X/Y/Z: approx. 2500mm/1300mm/1600mm, weight: approx. 750kg. Including two hydraulic punching machines Wolf EHPT 6E and two manual swivel arm punching machines. On-site inspection is possible.
A Schön swivel arm punching press and a Hang eyeletting machine are available. 1) Swivel arm punching machine Schön & Cie 8L, year of manufacture: 1973, pressing force: 18t, table dimensions X/Y: 900mm/450mm, swivel arm width: 350mm, stroke: 60mm, passage height: 83mm-183mm, oil capacity: 40l, weight: approx. 1200kg. 2) Eyeletting machine Constantin Hang 103 SCD KG, year of construction: 1993, machine dimensions X/Y/Z: approx. 600mm/1250mm/700mm, weight: approx. 50kg.
Output at 45 PSIG: 440kg/h, max. pressure: 8bar, max. temperature: 121°C, material: stainless steel, steam: sterile, machine dimensions X/Y/Z: approx. 1200mm/800mm/2850mm. On-site inspection is possible.
Flow rate: 20m³/h, delivery head: 41.5m, speed: 2925rpm, power at 50Hz: 5.5kW, 400V/690V, 10.3A/6A, power at 60Hz: 6.3kW, 460V, 10.1A, efficiency class: EFF2, weight: approx. 45kg.
Two similar Netzsch progressive cavity pumps are available. Power: 15kW, max. delivery pressure: 8bar, delivery rate: 1000l/h, speed: 1450rpm, max. viscosity: 1000Pas. One of the machines is mobile. On-site inspection is possible.
Two unused Allweiler and KSB pumps are available. 1) Thermal oil centrifugal pump Allweiler NIT 50-200U5 AW4, year of manufacture: 2023, flow rate: 40m³/h, delivery head: 54m, power: 7.4kW, speed: 2900rpm, pumped medium density: 0.75kg/dm³, viscosity: 1mm²/s, pipe diameter: 203mm. 2) Reconditioned cooling water pump KSB Etabloc, year of construction: 2021, flow rate: 26m³/h, delivery head: 15.5m, viscosity: 1mm²/s, speed: 2915rpm, MEI: 0.7, pipe diameter: 116mm. The KSB pump was overhauled in 2023. Documentation available. On-site inspection is possible.
Five Rietschle vacuum pumps including vacuum pump stands, switch cabinet and accessories are available. 1-2) Dry-running screw vacuum pump Rietschle Twister VSB 120, year of manufacture: 2006, intended use: continuous distillation, suction pressure: approx. 100mbar, back pressure: atmosphere, pumping speed: approx. 60m³/h, max. suction temperature: 60°C. 3-5) Three further vacuum pumps, year of manufacture: 2003. The pumps are controlled via a joint control cabinet. Documentation available. On-site inspection is possible.
Suction capacity: 78m³/h, final pressure: 60mbar, motor power: 1.5kW, speed: 1500rpm, weight: approx. 200kg. Documentation available. On-site inspection is possible.
Inverter heat pump. Very good condition. Was used for heating. Closed circuit. Glycol. Serviced. Power approx. 53 kW
sheet width: - mm plate length: - mm plate thickness: - mm total power requirement: - kW weight of the machine ca.: - t dimensions of the machine ca.: - m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Swivel arm punch Sandt, in good condition, immediately available Robsvvhfuer Sb Nwkju If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.
Pump module to add to VERTIwrap machines for filling liquids (milk, juices, water, etc.). - Specifications depending on customers product (product sample necessary). Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.
Piston pump module for VFFS or HFFS machines for dosing liquids and paste-like products. Suitable for various viscous substances (e.g. lotions, creams, ointments) and liquids (milk, juices, water, etc.). Controlled by servo motor, including storage hopper and stirrer. - Specifications: dosing range: 100-1000ml | accuracy: +/- 0,5-1% | speed: 45 cycles/minute at 70ml dosing volume | hopper capacity: 70L | power supply and consumption: 3-phase, 380V, 1,5kW | dimensions and weight: depending on final layout. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full w ...
used
Heidelberg Embossing Crucible TP, Machine Number T169693+ Heidelberg Embossing Crucible TP,T191298, Machine is in good condition, immediately available Rebevvikfer Sb Nwkju If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.
Rexroth Pump Axial Piston Pump AKP140R with Valve for ANGELS refurbished Type: AKP140R with valve Manufacturer Part Number: R901021899 Type code: SYDFEE-20/140R
Injection pump in exchange PS6-HL-50 ASSY 48270-00004 Mitsubishi S6R2
Wilo High Pressure Centrifugal Pump Economy MHIE 203N-2/V/3-2-2G,G1/G1,0.75kW 4171765
Pressure plate punch Beil 780/425-S-H-AP2; cleaned and tested; die-cut 780 and 425 mm autoplate; Investment Contact. Plate punch hatchet 780/425-S-H-AP2; cleaned and checked; punch size 780 and 425mm Autoplate; contact for plate.
Manufacturer: Hidrostal Model: F10K-SST+F2310-L Pump Type: Screw centrifugal pump Material: Stainless Steel Find more here - / Contact us at -
A hardly used Netzsch rotary lobe pump is available. Flow rate: 30m³/h, max. pressure: 2bar, max. temperature: 80°C, design: block design, number of poles: 6, operating hours: approx. 5h. Documentation available. On-site inspection is possible.
Bridge punch from Sandt with 30t
Atom cart beam punch with 25t. The machine is fully functional.
Bridge punch of the company Schön, model 64035 / 92 The machine is fully functional.
Sheet format: max. 1060 x 746 mm, min. 400 x 350 mm Equipment: Stripping station, depaneling, centerline, floor storage in depaneling station, Quick-Lock quick-release closing frame, max. machine speed 9,000 sheets/hour, max. die-cutting pressure 260 tons, processable materials: paper min. 70g/m², cardboard / solid board max. 1,000 g/m², corrugated cardboard up to 2 mm. Condition: Not operational Sale exclusively as spare parts donor Missing parts: Pumps, Grippers, Chain, Cube, Various Electrical Components Other: Machine can be visited by arrangement.
punching pressure: 16 t plate thickness: 8 mm plate length max.: 1250 mm sheet width - max.: 1000 mm engine output: 13 kW control: Cadman CNC voltage: 400 V weight of the machine ca.: 8,3 t dimensions of the machine ca.: 3600 x 2300 x 2000 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Stock number: PC2304, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Centrifugal pump, Motor: 1,1 kW - 220/380 Volt - 2870 rpm., Theoretical capacity: 15000 l/h., Manufacturer: APV, Type: W+ 22/20 220 120
Danfoss 83024044 PUMP-VAR-DISPL HYDRAULIC PISTON PUMP Weight: 24.6 kg Availability: 1 P.max. - 350 bar Nobmy Exov D Hk Ej Ipocu REF/Serial Number: 026-67039-0 Part number: C5V08-311B1 Manufacturing site/service centre: 41564 KAARST Germany PTS ID/Tracking ID: VKU82E77 Unique Identifier
Stock number: P349, Item: Vacuum pump, In stock: Yes, Amount in stock: 1 pc., Motor: 1,1 kW - 380 Volt - 1390 rpm., Theoretical capacity: 30 m³/hour, Manufacturer: Pfeiffer, Type: Duo 030 A
Brand-new Sauer Danfoss 11028185 Hydraulic Pump—a high-performance, durable hydraulic component designed for industrial and mobile machinery applications. Model Code: JRR045BLS192 Serial No: S074826737 Max Pressure: Up to 350 bar (verify with specs) Country of Manufacture: Made in Slovakia Ideal for heavy equipment, construction, and hydraulic systems Model No./Ident No.: 11028185 Net weight: 29 kg Manufacturer: Sauer Danfoss Availability: 2 Ncobsv D H Evomy Ex Ipeu
Stock number: PT1069, Material: Stainless acid proof steel AISI 316, In stock: Yes, Item: Lobe pump, Amount in stock: 1 pc., Motor: 0,75 kW - 220/380 Volt - 930 rpm., Theoretical capacity: 2957 l/h., Throughout: Vertical, Connections: Ø 1, Manufacturer: Ibex, Type: NMOG/322, Other: Plast lobes
Stock number: P348, High pressure pump, stainless steel,, Rannie type 18.50,, mounted on stainless foundation with wheels., 3,0 kW motor, variator gear., 350 – 1750 rmp., Series no. 4661/71., Material: Stainless steel AISI 304
Stock number: PM1063, Material: Stainless acid proof steel AISI 316, In stock: Yes, Item: Eccentric screw pump, Amount in stock: 1 pc., Construction: On a stainless foundation, Motor: 0,5 kW - 220/380 Volt - 670 rpm., Theoretical capacity: 1000 l/h, Stage: 1, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 1, Dimensions outlet: Ø 1, Manufacturer: Mono, Type: MD 30
Stock number: PM1553, Excentric screw barrel pump, stainless steel,, Flux, 1,1 kW motor, 900 rpm., 220/380 Volt., Bar Ø 50 x L 1000 mm., Material: Stainless steel AISI 304
Stock number: PM1574, Material: Stainless acid proof steel AISI 316, In stock: Yes, Item: Eccentric screw pump, Amount in stock: 1 pc., Construction: On a stainless foundation, Motor: 2,2 kW - 380/660 Volt - 1415 rpm., Theoretical capacity: 6000 l/h., Stage: 1 , Working pressure : Max 4,5 bar, Dimensions inlet: Ø 1½, Dimensions outlet: Ø 1½, Manufacturer: Mono, Type: MH40 D8
Stock number: P342, Membrane pump, plastic,, Almatec type A10., Runs on compressed air., Material: Plastic
Stock number: P321, Membrane pump, plastic,, Ø 3/4, Albin type AD0060PXT., Max pressure 5,5 bar,, max capacity 4800 l/h., Material: Plastic
Stock number: PM2076, Eccentric screw pump, stainless acid proof steel,, Seepex type BT 2-12., 1,5 kW. gear motor,, 220/380 V., 186 rpm., Screw feeding,, inlet flange L 350 x W 180 mm., Theoretical capacity 1.000 l/h., Material: Stainless acid proof steel AISI 316
maximum number of results exceeded
please refine your search
