pu 73 kr used for sale

Single column - eccentric press KRUPP type PEKRD 125 hMasch. No. 2861 Year of construction 1977Compressive force 125 ton. Projection 400 mmTable size 950 x 750 mmPlunger area 800 x 540 mmTable opening 100 x 250 mmStroke adjustment 8 to 160 mmPlunger adjustment 100 mmInstallation height largest stroke at the top max. 550 mmStroke rate 60 strokes/min. Table height above floor 800 mmEngine power 10 kWNetz connection 380 Volt, 50 Hz- Hydraulic overload in the plunger- Compressed air clutch-brake combination ORTLINGHAUS-

Clinch unit TOX - Pneumatic-Hydro Tox pressHydro-pneumatic press TOX Pressotechnik POWER PACKAGEType type CRS 03.62No.: 207599.2Year of construction approx. 2005Pressure capacity: max. 80 kN = 8 tonProjection: 20 mmInstallation height: 32 mm- Built-in clinch tool- pneumatic valve for control- Push-through joining or clinching- For making a form-fit connection of 2 sheets without perforating or heating the sheets- Mounted on the stand- with the simplest electrical control and Foot switchWeight: 230 kgComes from

Hand - Swivel bending machine KRAMER type AMS 650 x 1.5Hand swivel bending machine, bending benchYear of construction approx. 1985Working length 650 mmSheet thickness at 40 kg/mm2 1.5 mmUpper beam opening approx. 60 mmBending beam adjustment approx. 0-25 mmBending angle 0-180- Upper beam adjustment via hand crank- Pilot rail for the bending brace- One-piece sharp rail 135Space requirement L x W x H 1200 x 600 x 1100 mmWeight 160 kggood condition; used

Folding machine KRAMER type A-toll. II 1000Fabr. No. 48 287 Year of construction 1990Useful length 1060 mmmax. Sheet thickness 3.75 mmStroke of the upper beam 180 mmAdjustability of the bending beam 60 mmBack gauge 480 mmDrive power of bending beam drive 4 kWAdrive power of upper beam drive 1.5 kWNet connection 400 volts, 50 Hz- manual and semi-automatic control- angle adjustment via angle selector- one-piece pointed rail 135- back gauge with hand crank adjustment and simple measurement scale-

New electric scrubber drier, floor cleaning machine KREMER type KR-FL50AByear of construction 2024Theoretical area output 2000 mª/ hWorking width 510 mmCleaning brush 510 mmBrush speed 175 rpm. Suction lip width 850 mmTank volume pure water: 50 litresTank volume dirty water: 50 litresNoise pollution 66 dBaClimbing capacity 2%Battery voltage 24 volts, 100 AH- battery charger 24 volts- battery 24 volts, 100 AH- one cleaning brush- two separate tanks- without drive drive, the device

OFFER - KRÜSIMATIC from Krüsi G1 4 axis system 1 used carpentry machine from KRUeSI type Kruesimatic G1 Year of manufacture 2005 Can be operated with all carpentry programs such as Catwork, SEMA, Lockrichs, S & S, Nut Reiner, etc. 4 axis system with dovetail cutter Task / Editing from right to left 6 Side processing without having to turn the wood! Total length approx. 18 m Weight 5.5 t BTL controlled for interface to the office or of course manual input on the machine. To increase the cutting performance, the feed rate is frequency-controlled and can be optimized for many cross-cut cuts Platform height without floor shaft 920 mm Sections fall into mobile box incl. chips The system only needs to be connected to the electrical cabinet with plugs Max. wood cross-section - 200mm x 320 mm Plant set up and ready for demonstration Available IMMEDIATELY The entire system ha ...

a KM-200-1000 machine with removal robot built in 2006 for sale. The machine is in neat condition and serviced by Krauss Maffei.

4-rolls Kramatorsk plate bending machine Ultimate tensile strength of material: 500 MPa (50 kg/mm²) Yield strength – cold bending: 250 MPa (25 kg/mm²) Yield strength – hot bending (primary): 100 MPa (10 kg/mm²) Yield strength – hot forming (secondary heating): 45 MPa (4.5 kg/mm²) Elongation at cold state: ±18% Maximum sheet width: 4000 mm Max sheet thickness – cold, without pre-bend: 71 mm Max sheet thickness – cold, with pre-bending: 63 mm Max sheet thickness – hot forming: 150 mm Minimum bending radius – cold: 560 mm Minimum bending radius – hot: 600 mm Maximum radius for closed bending (curled edge): 1000 mm Main motor: 160 kW Weight: 730 tons

Kraus and Reichert Kuris KVS700 Bumper Knife Machine Fabric Cutter Textile Item condition: Used and tested for function. _RD 6kg More textile machines - new and used - can be found in our shop! International shipping costs on request!

Two injection moulding machines Krauss Maffei are available. 1) Krauss Maffei KM 50 C1, year of manufacture: 1999, injection unit: SP220, screw diameter: 30mm, L/D ratio: 23, injection pressure: 2500bar, shot volume: 85cm³, machine dimensions X/Y/Z: approx. 3200mm/1350mm/1800mm, weight: approx. 2500kg, control: MC4, operating hours: approx. 86000h. 2) Krauss Maffei KM 125 C1, year of manufacture: 2000, injection unit: SP520, screw diameter: 45mm, L/D ratio: 20, injection pressure: 1878bar, shot volume: 217cm³, machine dimensions X/Y/Z: approx. 4500mm/1550mm/2200mm, weight: approx. 5500kg, control: MC4, operating hours: approx. 82000h. Documentation available. An on-site inspection is possible.

Ref. no.: 18586 Hersteller: KRAUSS MAFFEI Year of construction: 2011 Clamping unit Clamping force: 180 ton Opening stroke: 450 mm Distance between tie bars: 560 x 510 mm Mould height min.: 200 mm Mould height max.: 600 mm Opening width: 1050 mm Platen size (h x v): 790 x 740 mm Injection unit Screw diameter: 50 mm Injection volume: 393 cm³ Shot weight: 357 g Injection pressure: 1892 bar Measurements and weight Dimensions: 6,10 x 1,90 x 2,10 m Machine weight: 8400 kg Robot Producer: Krauss Maffei Type: LRX-100 Year: 2012

KUKA Robot KR30L15/2 Year of manufacture 2002 Weight 930kg Only 75`000 operating hours PC control type K C2 including panel Drive controller KSD Control cabinet KR CC USB stick with documentation and schematics Unloading and machine data in the appendix Annually serviced by Kuka Roboter Schweiz AG with service contract maintained Robot is fully functional and in very good condition Including various spare and new parts Is ready for pickup, loaded on pallets Included: Axis control module KSD1-48, new price 1900,-CHF Power supply KPS600/20, new price 4500,- CHF Three-phase servo motor CO/KKSSY, new price 2200,- CHF Control PC KC2, new price 5400,- CHF CI board / mains filter / cable sets, approx. selling price 800,- CHF Axis control module KSD1-32, new price 1400,- CHF Axis control module KSD1-08, new price 1200,- CHF Support batteries / HDD hard disk / motor protecti ...

Clamping force: 1500kN, screw diameter: 50mm, tie bar spacing: 500mm, platen dimensions X/Y: 780mm/790mm, opening stroke: 600mm, daylight: 900mm, ejector stroke: 150mm, shot volume: 305cm³, injection weight: 278g, injection pressure: 2336bar. Machine dimensions X/Y/Z: approx. 4700mm/1550mm/2200mm, weight: approx. 7000kg, control: MC4. Includes Sepro handling system. Documentation available. An on-site inspection is possible.

Injection molding machine Krauss Maffei KM 800-4300 MX BJ 2006

Injection molding machine Krauss Maffei KM 650-4300 CX BJ 2010

A cold glue rotary labelling machine Krones is available. Product: wine, bottle formats: 0.75l/1l, labelling capacity: 10000 bottles/h. Includes all format parts and spare parts. Documentation available. An on-site inspection is possible. Expected to be available from February 2026.

Grinder with mixer Manufacturer: Kramer Grebe Wetter Model: Grinder 130mm Made of stainless steel Lowest noise level Easy cleaning Hopper volume: 245 liters Voltage: 400V 50Hz Weight: 850kg

A mobile welding fume extraction unit Schmidt & Kranz is available. Air flow rate: approx. 1800m³/h, power: 1.5kW. An on-site inspection is possible.

length: 880 mm weight: 60 kg height: 320 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

loading area: mit Untergestell weight: 125 kg length: 900 mm height: 350 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

- Year of construction: 2022 Cooling: - from 30 °C to 25 °C = 29 kW - from 15 °C to 0 °C = 15.4 kW - Connected load : 8.8kW, 15.6A - Dimensions : 1.05m x 1.05m x 1.75m (L x W x H) - Machine in very good condition - Very few hours of operation!

Cleanable transport screw Brand: van Beek (The Netherlands) YOM: 2016 Screw length: 1550mm Screw dia: 310mm The screw can easily be extended to clean. Dimensions ready for use: LxWxH 2800mm x1300mmx1150mm Dimensions ready to clean (extended) LxWxH 4250mm x1300mm x 1150mm Condition: very good Video's available.

2012 KRAUSS MAFFEI 850-1400-1000 MX Z Injection moldin machine missing electrical and mechanical parts Find more here - / Contact us at -

diameter: 800 mm roll surface width: 1800 mm heating system: Sattdampf 0 0: 860 Liter 0: 5 bar max. temperature: 168 ° C weight: kg range L-W-H: 2,2 x 0,8 x 0,8 m 4 pieces in total, drying drums Ø 800 mm, steam-heated, including pedestal bearings, foto no. 4 shows how the drying cylinder works. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Height=1.62 m, Overall length= 0.88 m, Overall width= 0.81 m, Net weight= 167 kg,

Height=1.05 m, Overall length= 0.62 m, Overall width= 0.55 m, Net weight= 64 kg,

Height=1.235 m, Overall length= 1.003 m, Overall width= 0.856 m, Net weight= 90 kg,

Height=1.35 m, Overall length= 1.3 m, Overall width= 2.15 m, Net weight= 1390 kg,

Height=1.36 m, Overall length= 0.64 m, Overall width= 1.5 m, Net weight= 250 kg,

Height=1.36 m, Overall length= 0.64 m, Overall width= 1.5 m, Net weight= 250 kg,

Height=1.5 m, Overall length= 1 m, Overall width= 1.1 m,

A total of 71 Kroll air heaters are available, 30x LH 130 V10, 1x LH 130 V20, 7x LH 230 V10, 3x LH 330 V10, 1x LH 420 V10, 6x LH 430 V10, 1x LH 430 V20, 11x LH 530 V10 and 11x LH 630 V10. The fans are used and partly have bent fins and scratches. An on-site inspection is possible.

Krones Sleevematic – Multireel – Shrinkmat Sleeve Labeling System Complete shrink sleeve labeling solution combining three advanced Krones technologies into a fully integrated system for the decoration and labeling of PET and glass containers. The system ensures high precision, continuous operation, and maximum production efficiency in modern beverage bottling lines. General Information - Manufacturer: Krones - System Type: Shrink sleeve application and shrinking system - Maximum Capacity: up to 39,000 bottles per hour - Bottle Sizes: 250 ml – 1,500 ml - Container Types: PET and glass bottles Delivery Scope - The system includes the following equipment: - 1 × Krones Sleevematic TS - 1 × Krones Multireel S - 1 × Krones Shrinkmat System Components Krones Sleevematic TS - High-performance sleeve applicator designed for precise application of shrink sleeves on ...

length: 685 mm width: 460 mm height: 115 mm T-slot - width: 10 mm T-slots: 3 Stück Payload: 40,0 kg width: 315 mm length: 340 mm travel -x axis: 285 mm travel -y axis: 140 mm manual control device: 0,04 Nonius mm weight: 45,0 kg Properties: for light milling work on table or crevice drilling machines Ground clamping surface Dovetail guide adjustable by means of wedge lines The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Height=1.52 m, Overall length= 3.85 m, Overall width= 0.95 m, Net weight= 600 kg,

Kuka robot KRC2sr + KCP2 + KR5 sixx R850 Number of axes: 6 Max. load capacity: 5 kg Max. intervention: 850 mm Year of Make: 2006 Scope of delivery: robot, controller, cable, teaching panel, operating instructions, circuit diagrams. Shipping costs within Germany 95€.

sheet width: 1020 mm plate thickness: 1,5 mm daylight opening: max. 85 mm weight of the machine ca.: 240 kg dimensions of the machine ca.: m Smallest bending width factor 10 x sheet thickness s Smallest inner radius factor 1.5-2 x sheet thickness s Lowering capability of the lower and bending beams 20 mm On this swing-beam bending machine, the beams and side stands are reinforced with particularly strong ribbing. The cross-sections are designed to be strong enough to bend even narrow offsets. On the AML 1000 model, the bending beam is balanced by a gas pressure spring. The opening width of the upper beam and the lowerability of the lower and bending beams are generously dimensioned. The machine is being sold as defective because the connection between the lower frame and the right side stand is broken (see photo taken from behind)! The data for this ad was created with ModulMWS - the s ...

Injection moulding machine Krauss Maffei KM 50/90 C2 BJ 2001

Inspektor Linatronic along with contour detecion module: • Type: Krones Linatronic K735 • Manufacture year: 2012 • Capacity: max. 60 000 bottles/h. • Direction of operation: from left to right Possible detection: • Residual liquid (infrared) • Double check of residual sodium (high frequency) • Inspection of neck damage • Side wall control modules - 4 modules • Rejection of damaged bottles • Separate rejection of dirty bottles • Bottle contour detection • Bottle color detection • Separate rejection of bottle with wrong contour or color The Inspection unit contains the conveyor which separates bottles before the entry to the Inspector and the Ejector table after. Total lenght of the Unit: 11300 mm

Manufacturer: Krauss Maffei Model: 800-5700 MC Year of Manufacture: 1999 Technical Data - Clamping Force: 8000 kN - Platen Size: 1600 × 1510 mm - Tie Bar Distance: 1120 × 1000 mm - Mold Height: 600 – 1100 mm - Daylight (Platen Opening): 2000 mm - Total operating hours (machine switched on) : currently 02,193.40 - Operating hours in production : currently 82,849.13 - Heating Capacity: 59 kW - Control: MC4 Injection Unit - Screw Diameter: 105 mm - Shot Volume: 3611 cm³ - Injection Pressure: 1580 bar - Dimensions (L×W×H): 10.15 × 2.86 × 2.40 m - Pump Drive Power: 110 kW - Oil Tank Capacity: 2000 L - Machine Weight: approx. 45 tons Features / Extras - 8 temperature control zones + 2 additional zones for plasticizing heating - 4 core pulls with movable platen - Hydraulic rotary bolt shut-off nozzle (HSVS) - Air valve (1x on movable platen, WAP) - T-slots in clamping plates ac ...

KRAUSS MAFFEI TWIN SCREW EXTRUDER (photos before reconditioning), Mod.KMD 2-90 KK, used for profiles, n.2 parallel screws diam. 90 mm 20 L/D Max 30.5 rpm, 40 kw d.c.drive, installed power 180 kw, feeding hopper, max production with PVC profile 240 kg/h, complete with control cabinet, Heating 28.5kW,, 5 Zones Heating and 2 Last Barrel Oil Cooling Barrel +1 Zone Adapter 4 Zones Double Die, degassing point, Measures 4.3 L x 1. 2 W x 2.3 (m) H (incl Hopper) ,, Approx.weight 4.3 Ton

Injection moulding machine Krauss Maffei KM 300-1900 C2 BJ 2000

Height=0.98 m, Overall length= 0.69 m, Overall width= 0.56 m, Net weight= 149 kg,

Height=1.275 m, Overall length= 0.99 m, Overall width= 0.75 m, Net weight= 90 kg,

KRONEN GEWA 2600V – Fully Refurbished Vegetable Washing Machine, We are offering a Kronen GEWA 2600V vegetable washing machine in excellent condition, fully refurbished and ready for immediate use., Refurbishment Details:, - Completely overhauled by professionals, - Fitted with a brand-new original pump, - All parts inspected, cleaned, and tested, - Machine runs smoothly and efficiently, Features:, - Efficient vegetable and salad washing system, - Gentle product handling through whirl washing principle, - Made of high-quality stainless steel, - Ideal for food processing companies, - Location: Emmeloord, Available Immediately, Invest in a high-quality machine with the reliability of KRONEN – now with the added value of a full refurbishment and a new pump!, For more information, photos, or to schedule a viewing, please contact us.

Pallet nailing machine Böhm & Kruse Year of Make: 1980 Pallet mounting size max. 1200 mm x 1650 mm 20 nail guides good, ready-to-use condition

Blowing machine Krones Contiform 308 year of manufacturing: 2015 capacity: 18.000 bph neck size: PCO 28 - 1881 only 20.000 working hours with preform feeding system and chiller immediately available in Germany

A wood dust extraction and filtration system Krämer for saw lines is available. 1) Wood dust extraction unit Krämer VKA-P 100/650/55, air volume flow: 27000m³/h, pressure increase: 3800Pa, motor power: 55kW, V-belt length: 3550mm. 2) Filtration unit Krämer GFS Shake 160/25/250, filtration capacity: 30000m³/h, filter material: polyester needle felt, material discharge: TFS40/10/1.1. 3) Fan Krämer VFM-R 45/250/3, air volume flow: 3000m³/h, pressure increase: 2500Pa, motor power: 3kW. 4) Fan Krämer VFM-P 42/200/4, air volume flow: 2500m³/h, pressure increase: 3000Pa, motor power: 4kW. 5) Separator tank/filter hopper Krämer. 6/7) 2x axial fans. Including pipes and peripheral equipment. The motor flange on the discharge motor is defective. Documentation available. An on-site inspection is possible.

Grinder Manufacturer: Kramer Grebe Wetter Model: Grinder 160mm Integrated lift for ergonomic operation Made of stainless steel Lowest noise level Easy cleaning Rated power: 36 kW Control voltage: 24/230 V Operating voltage: 400 V / 50 Hz Total nominal current: 63 A Fuse protection: 80 A

Paper cutting machine with 39cm cutting width. cleaned and checked