process used for sale

6 containers 200 litres made of V2A, single-walled, used Design: upright

Inv. Num. : 8242 Type: VC 560 Producer: Spinner Created: 2007 Parameters: Control system: Siemens Work table length: 650 mm Work table width: 480 mm Maximum vertical spindle speed: 6000 1/min X-axis travel: 560 mm Y-axis travel: 400 mm Travel Z axis: 400 mm Cone: SK 40 Number of all tools: 16 pieces Equipment: Cooling

CNC processing centre Brand: IMA Type: BIMA 310V 120/600 Year: 2004 Technical data: Machining area - in X-direction without gluing 6000 mm - in X-direction motor gluing 5000 mm - in Y-direction 1200 mm - in Y-direction with main spindle + WZ-Ø 20 mm 1300 mm max. clamping height from Upper edge of suction plate Z1 100 mm max. workpiece thickness Z 2 depending on equipment/application Worktable height: approx. 950 mm 1 main spindle with feed stroke pneum. - Drive power: 12 kW in S-1 operation - Tool holder: HSK F63, taper diameter =38 mm - Tool feed: automatic - Pull-in force: 11000 N - Tool weight: max. 6 kg - Direction of rotation: right/left rotation, programmable - Speed range: stepless 1500 - 24000 rpm, programmable - Drive: frequency-controlled three-phase motor Spindle lubrication: unique factory grease lubrication - spindle cooling: water cooling  ...

x-travel: 450 mm y-travel: 400 mm z-travel: 400 mm control: Heidenhain Mill Plus V600 total power requirement: kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 8267 Type: S56 Producer: Makino Created: 2009 Parameters: Control system: FANUC 310is Work table length: 1000 mm Work table width: 500 mm Maximum table load (uniform): 650 kg Maximum vertical spindle speed: 20000 1/min X-axis travel: 900 mm Y-axis travel: 500 mm Travel Z axis: 450 mm Cone: HSK-A63 Number of all tools: 30 pieces Machine height: 3063 mm Machine length: 3302 mm Machine width: 2570 mm Machine weight: 7500 kg

Vertical Machining Center HWACHEON Vesta-1000 10K Control: Heidenhain iTNC 620 Year of Make: 2014 Original pictures will follow. Travel: X-axis:1,000 mm Y-axis: 550 mm Z-axis: 500 mm Table size: 1,100 x 502 mm Table load: approx. 700 kg Recording: BT 40 Tool magazine: 30 compartment Spindle speed: 12,000 rpm Drive power:18.5 kW Equipment -Conveyor - Electronic handwheel - 4th axis

Fuji FLHZ 85 CD Quartz 3 Plate Developing Machine; very good condition; cleaned and tested; Inlet width 850mm; Chiller. Plate processor Fuji FLHZ 85 CD Quartz 3; very good condition; cleaned and checked; working width 850mm; Chiller.

Mobile 290L vessel incl. discharge with valve, inspection glass, etc.

Dimensions (L,W): 1000 x 800 mm For sale are 51 machine pallets for Burkhard and Weber MCR 120 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 8330 Type: HR 8A Producer: MITSUI-SEIKI Generated: Parameters: Control system: FANUC Work table length: 1295 mm Work table width: 1295 mm Maximum table load (uniform): 3992 kg X-axis travel: 1800 mm Y-axis travel: 1500 mm Travel distances Z-axis: 1200 mm Machine height: 5500 mm Machine length: 12000 mm Machine width: 9200 mm Machine weight: 45000 kg

Specifications: Manufacturer: 3M ESPE Type: Lava CNC 500 Control: Beckhoff Year of Make: 2008 Compressed air: 6.5 bar Rated power: 1 kW Rated mains frequency: 50/60 Hz Weight Weight: 620 kg Condition Condition: Used Functional: Tested and fully functional

Control Ultimax 3-4 2 color screens (text + graphics) Travel X/Y/Z 1020/510/610 mm Speed 8000 1/min Tool magazine for 24 Wkz. SK 40 DCF Software

Elmo Rietschle VC300 Vacuum pump 3x Elmo Rietschle oil lubricated rotary vane pumps, 5.5Kw, 300 M3/H flow rate

Baader 694 Bone Separator 500kg raw material per hr 3mm drum New belt and new blade, serviced.

Baader 697 Bone Separator Model: 697 Rated at 1200kg raw material per hr 3mm drum Ex butter factory. Supplied with new side hopper Full working order

Baader 580 Fish Filleting Machine x2 units available 2012 & 2004 Regularly serviced and well maintained, ex factory Whitefish

Baader Filleting Line Includes conveyors, header, 588 filleting machine, trimming line, spares, shaprening machine 2021 Full details on request

Baader Fish Filleting Machine Model: 185 Designed for medium-large whitefish Last used on cod/haddock Overhauled in 2020 and little use since

Fish Skinning Machine Make: Steen Model: ST600 Built 2008 Regularly serviced and well maintained

Deglazing Machine Electrically heated 1000mm belt width Make: Sharp Built 2019

Manufacturer: Cognex Type: In-Sight 9912 IS9912M-373-50 (monocromn with RedLine) From stock liquidation Location: Stuttgart

FILLETING MACHINE FOR MACKEREL, VMK Technical description: Belt width:70 mm Power supply: 220/380 V, 50/60 Hz Total dimensions: 2360 x 800 x 1680 mm

AUTOMATIC FEEDER FOR HERRING, SARDINE, BAADER 488 Technical description: Power supply: 400 V, 50 Hz, 3 Ph Approx dimensions: 3100 x 1400 x 1900 mm It can be combined with Filleting machine for herring, sardine and mackerel Baader 35

x-travel: 1300 mm y-travel: 610 mm z-travel: 600 mm taper: Aufnahme 50 Axis: 3 control: Heidenhain 530 : : ja : 20 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

material width: 1015 mm material thickness: 1 mm speed: von Hand weight: 240 Kg dimensions: 1420 x 600 x 750 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

material width: 305 mm material thickness: 1,0 mm speed: von Hand weight: 45 Kg dimensions: 500 x 340 x 420 m Combined sheet metal working machine with: - Bending, tool widths 25 - 50 - 75 - 75 - 105 mm. - Rolls, roll diameter 38 mm - scissors, max. 1015 x 1mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

FILLETING MACHINE BAADER TYPE: 208 Technical description: Output conveyor width (x2): 108 mm Power supply: 400V / 50 Hz Power: 2,6 kW Dimensions: 3750 x 1050 x 1250 mm This machine processes small gutted and headed hake, small haddock, saithe, cod and whiting. The cuts of the spring-loaded circular knives being controlled by the fish itself, the BAADER 208 produces single fillets with skin of high quality and with best yield. The BAADER 208 is easy to maintain and to operate. All functional areas are very well accessible. The machine is of robust construction and consists mainly of stainless materials so that it has a long service life also when used at sea.

SALMON BELLY SLICER, KAJ OLESEN A/S, TYPE TRIM-UNIT Technical description: Serial number: 11-01 Power supply: 3X400 V; 3,0A Bandwidth: 590 mm Dimensions: 2600 mm X 1150 mm x 1300 mm

Control: HEIDENHAIN TNC-430 x-travel: 800 mm y-travel: 600 mm z-travel: 500 mm B-axis (table): 280 mm table swivelabel +/-: 220 (+/-110) ° -C-axis table rotating: 360 ° tool magazin:: 30 spindle taper: HSK63 spindle turning speed - stepless: -15000 U/min rapid traverse feeds rotary table: 36 U/min rapid travel x/y/z: 36 m/min Overall size: 3800X3600X3000 mm weight of the machine ca.: 8.5 t Coolant through spindle: pressure: 40 Bar 3D measuring tracer: RENISHAW Chip conveyor: Coolant installation: SIEMENS 840D www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Control Winmax Travel X/Y/Z 2135 x 865 x 762 mm Spindle speed 12,000 min-1 Tool magazine for 40 Wkz., SK 40 Handwheel Ultimotion IKZ 40bar Probes Renishaw Conveyor

HEADING AND FILLETING MACHINE FOR SALMON AND MORE, CARNITECH TYPE: CT2620 + CT2630 Technical description: Heading machine CT2620 Power supply: (3x) 400 V, 50 Hz, 8 A Machine number: 08-0081 Year: 28/08/08 Dimensions: 4200 x 2100 x 1800 mm Filleting machine CT2630 Machine number: 08-0067 Year: 18/06/08 Power supply: (3x) 400 V, 50 HZ, 11 A Dimensions: 1800 x 850 x 2000 mm CT 2620 has been designed for head and tail cutting of salmon fish from 2 to 7 kg. The product is fed to the machine via a feeding chute, after which several operations are carried out on the fish, as the round attachment rotates one quarter of a revolution for each push on the button on the operation panel, see section 3.0 for further details. During initial operation, the occiput is sawed through with a round knife, where upon a guillotine knife tilts down to cut off the head, which then lands in the waste carrier  ...

FILLETING MACHINE, BAADER 36 Technical description: Power supply: 400 V/50Hz Dimensions: 3500 X 1000 X 1700 mm - 2300 X 1000 X 1100 mm Can be combined with Automatic feeder BAADER 488 The BAADER 35 can process herring, from 20-40 cm (75-450 g), mackerel and silver smelt 24-40 cm (130-600 g), blue whiting 22-40 cm (75-350 g) as well as trout 25-38 cm (160-600 g) with all usual cuts. Amodified version for smaller herring from 17-32 cm (35-240 g) is BAADER 36. Separate drives of heading and filleting sections enable operation of the heading section as a separate machine with an optional nobbing attachment. Only on operator is required when the BAADER 35/36 is combined with the automatic feeder BAADER 482, 483 or 484. A skinning machine BAADER 55 can be attached for the production of skinless herring fillets.

FILLETING MACHINE FOR SARDINE, HERRING, BLUE WHITING, BAADER TYPE: 134 Technical description: Power supply: 380 V, 50 Hz, 12,0 A, 2 kW, 3 Ph Dimensions: 3000 x 2100 x 1200 mm Weight: 450 Kg Can be combined with Automatic feeder for sardine and herring, Baader type: 478 This machine is especially designed for the filleting of small herring and pilchard with an overall lentgh of 15-25 cm (25-125 g), the convenient infeeding procedure and the steplessly adjustable operating speed permit high throughput. Excelent yield is guaranteed by a meat-saving selfadjusting headcut, adjustable tailcut and reliable passage through the filleting tools leading to smoothly cut block-fillets, single fillets without dorsal fins as well as belly cut herring with or without tail fins. Combined with the automatic feeder BAADER 478, the machine becomes an automatic filleting unit operated by only one person fo ...

FILLETING MACHINE BAADER 35 WITH NOBBING SYSTEM (SINGLE OR BUTTERFLY FILLET) FOR HERRING (20-40 CM), MACKEREL (24-40 CM), BLUE WHITING (22-40 CM) AND OTHER PELAGICS Technical description: Serail number: 10-1363-0035 Year: 1992 Throughput: 100-200 pieces/min Dimensiones: 3300 x 1250 x 1800 mm The BAADER 35 can process herring, from 20-40 cm (75-450 g), mackerel and silver smelt 24-40 cm (130-600 g), blue whiting 22-40 cm (75-350 g) as well as trout 25-38 cm (160-600 g) with all usual cuts. Amodified version for smaller herring from 17-32 cm (35-240 g) is BAADER 36. Separate drives of heading and filleting sections enable operation of the heading section as a separate machine with an optional nobbing attachment. Only on operator is required when the BAADER 35/36 is combined with the automatic feeder BAADER 482, 483, 484 or 488. A skinning machine BAADER 55 can be attached for the produc ...

PACKING MACHINE FOR TUNAFISH AND ANOTHER FISHES, HERFRAGA MODEL SM-2C Technical features: Output: up to 50 cans/minute Recommended output: 20 to 50 cans/minute (according the can type) Format: diameter 150 mm Cans height: max. 120 mm

Mixing and homogenizing plant capacity 50L Pre-melting tank 50L extra price Euro 6.500,--

PACKING MACHINE FOR TUNAFISH AND ANOTHER FISHES, HERFRAGA MODEL SM-110 Technical features: Output: up to 100 cans/minute Recommended output: 40 to 80 cans/minute (according the can type) Formats: 1 unit with format diameter 73mm (ID 2015) 1 unit with format diameter 99mm Others formats: diameter 65mm, 1/2 oval, 1/4 oval Cans height: 25-62mm

x-travel: 800 mm y-travel: 500 mm z-travel: 500 mm control: Siemens total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Control: Manufacture: SIEMENS 840D x-travel: 600 mm y-travel: 560 mm z-travel: 510 mm table-size: 900 x 560 mm spindle turning speed range: 12000 U/min tool magazin:: 30 weight of the machine ca.: 5 t HEIDENHAIN TNC-426 Prepared for the 4th axis www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock number: SF171, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 1 pc., Item: Gel press filter column, Construction: Hanging in tiltable stand, Top: Air controlled press cylinder, Bottom: Product filter, Dimensions: Column - Ø 300 x H 1000 mm , Type: Dan-Process

x-travel: 762 mm y-travel: 508 mm z-travel: 508 mm B-axis (table): +120/-35 Grad c-axis: 360 Grad control: HAAS für 5 Achsen tool piece magazine with: 40 Plätzen number of spindle speeds: 12000 U/min dimensions of the machine ca.: 4.3 x 2.35 x 2.8 m weight of the machine ca.: 8.5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock number: SF139, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 2 pcs., Item: Process filter, Design pressure: 10 bar, Design temperature: 65º C, Connections: Ø 150 mm, Manufacturer: Fagerberg, Type: 68CDF4MRSSM3, Other: 15 filter cartridges

Control: Manufacture: FANUC 0iM x-travel: 620 mm y-travel: 470 mm z-travel: 400 mm table-size: 700 x 450 mm spindle turning speed range: 10000 U/min tool magazin:: 20 weight of the machine ca.: 4.5 t HEIDENHAIN TNC-426 Prepared for the 4th axis www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock number: SF129, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 2 pcs., Item: Process filter, Connections: Ø 1½, Type: Danmil, Other: Housing for 3 pcs. filter cartridge - Excl. filter cartridges

Control: Manufacture: FANUC 18i-MB x-travel: 510 mm y-travel: 360 mm z-travel: 300 mm table surface area: 600 x 360 mm spindle turning speed - stepless: 12000 U/min dimensions of the machine ca.: 1400 x 2300 x 2300 mmxmmxmm weight of the machine ca.: 2.6 t tool piece magazine with: 24 Plätzen tool piece magazine with: 20 Plätzen The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 6000 mm y-travel: 1000 mm z-travel: 1200 mm table-size: 6400x1000 mm tool change unit: 80x spindle taper: HSK A100 spindle turning speed range: 45-9000 U/min total power requirement: kW weight of the machine ca.: 48 t dimensions of the machine ca.: 12x4.3x4.5 m SIEMENS 840D 4th axis B-Axis +/-90° Spindle coolant through spindle Tool measuring device www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Control: Manufacture: HEIDENHAIN iTNC 530 x-travel: 800 mm y-travel: 500 mm z-travel: 540 mm table-size: 910x500 mm spindle turning speed range: 10000 U/min tool magazin:: 24 weight of the machine ca.: 8 t HEIDENHAIN TNC-426 Prepared for the 4th axis www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock number: SF101, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 3 pcs., Item: Process filter, Filter house: Ø 95 x 280 mm, Connections: Ø 1, Other: Excl. filter cartridge

Travel (X / Y / Z) 762 mm / 508 mm / 610 mm Table size 1,020 mm × 510 mm Table load max. 1,000 kg Spindle holder SK 40 (DIN 69871) Spindle speed max. 10,000 min⁻¹ Spindle power 11 kW Tool Stations 24 Stations, Automatic Tool Changer (ATC) Iobjwt Rfwstfb Tpmjic Max. tool weight 7 kg Max. tool length 300 mm Max. tool diameter 80 mm Rapid traverse (X / Y / Z) 24 m/min / 24 m/min / 20 m/min Feeds programmable up to approx. 7,600 mm/min Control HURCO Ultimax 4 Machine weight approx. 4,700 kg Machine dimensions (L × W × H) approx. 3.9 m × 2.4 m × 2.7 m

Control: Manufacture: FANUC 0i-MD x-travel: 1000 mm y-travel: 550 mm z-travel: 500 mm table surface area: 1100 x 500 mm spindle turning speed - stepless: 10000 U/min dimensions of the machine ca.: 3500 x 2200 x 2700 mmxmmxmm weight of the machine ca.: 6.5 t tool piece magazine with: 24 Plätzen The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.