presses line used for sale

Nominal force 400 kN Stroke rate - 70/140 / min Motor 3/4 kW Exploitable stroke - at constant. Clutch brake temperature 50/45/min Capacity - material thickness 4-6.4 m - with single strokes, 2-3.2 mm - with continuous stroke Table 660 x 530 mm, table top 650 x 515 x 75 mm Stroke adjustment - 10-125 mm, Dimensions 1250 x 1600 x 2370 mm - High , Btto 4500 kg Reconditioned machine - warranty 9 months from delivery date

Used belt press made by Monobelt, type NP12CK. New 2009. Weight 1620kg. Belt width - 1200 mm. Working flow - up to 10 m3 / h. Throughput max - 170-360 kg DM / h. Installed power: Press with 0.55 kW thickener 2.2 kW flushing pump Rinse water quantity 5 m3 / h Net weight / maximum usable weight 1620/2800 kg Sludge inlet connection DN80 1 ”GF rinse water inlet Filtrate outlet connection DN150 Manufacturer's documentation.

Used press for pre-pressing cheese. Technical data: - producer TEWES BIS Barczewo - year of production 2006 - dimensions: overall length 4780 mm, width 1560 mm, height 3850 mm - pressing area 4.33 m3 - internal dimensions of the bath: length 3700 mm, width 1170 mm, depth 730 mm - mass of pressed cheese approx. 1000 kg - thickness of the cheese layer after pressing approx. 250 mm

We sell a used and revised TTW with a deposit of 30-100g.

-) 2-jaw drill chuck 20 mm -) Dowel drilling device with 4-compartment grid 16-32-22-25 mm -) 90° frame stop pluggable -) Miter stop 45° and 22.5° pluggable -) Moving equipment -) Workpiece clamp manual 2 pieces -) Suction connection D 100 mm Optional accessory: -) Gauge in handwheel -) infinitely variable double angle miter stop -) 1 lever operation -) switchable pneumatic stroke for two planes -) Leaser on request

Passage width 2500 mm Stroke 900 mm Total power requirement 62 kW Machine weight ca. 27,5 t Dimensions L x W x H approx. 3950 x 2200 x 4850 mm Retraction force 40 t Master cylinder 2 pieces Column diameter 220 mm Installation height 1300 mm Table size 2500 x 1600 mm Ram size 3100 x 16000 mm Table height above floor approx. 900 mm Flow speed 200 mm/sec Return speed 200 mm/sec Working speed 5 - 15 mm/sec Oil tank 1500 l Oil quantity 1200 l Pressure control adjustable from up to 50 - 400 t Thermoforming cushion 1400 x 800 mm Deep-drawing unit capacity 30 - 60 t Deep-drawing cushion stroke 250 mm Deep-drawing cushion speed 5 - 80 mm/sec robust machine body with solid welded construction low-maintenance and reliable Piston rod with induction hardening and chrome cladding T-slots according to customer requirements, if not specified 22mm according to DIN CE Certific ...

Specifications: - working length 3500 mm - Stand passage 3050 mm - max pressing force 2000 kN - Distance table / ram max. 480 mm - Stand projection 260 mm - Ram stroke approx. 300 mm - Lifting speeds - Downspeed idle max. 100 mm/sec - Boost speed 80 mm/sec - Downward pressing speed max. 10 mm/sec - Total drive power 25 kW - Space requirement approx. W 4500 x H 3150 x D 2100 mm - Weight approx. 16000 kg -with: - CNC control CYBELEC renewed in 2008 - controlled crowning device - controlled backgauge with height adjustment 5 - 1000 mm - hydr. Tool clamping - Upper tool + universal die tool - Material requirements - Two-hand control panel

Bürkle Multifoiler Model BTF 1628/60 Year 1997 Plant for coating smooth and formed MDV parts with thermoplastic films, of roll or as a cut, for film PVC,PP,high gloss PVC,ABS. Suitable for thermoforming or membrane process. Max part size 1250x 2550 mm/ Divide thickness 6-35 mm Hot plate dimensions 1600 x 2800 mm max heating temperature 140° Stroke 230 mm Control Siemens Total connection 38 Kw Weight 16,5 t

Single-column press with 15 T power suitable for continuous shift operation (a) travel speed 10 mm downwards; b) Opening speed up to 25 mm/sec c) Starting pressing speed 10 mm/sec d) Table size 400x400 mm e) Ram size 200x200 mm, with T slots and central cylinder tension f) Total size approx. 1150x800x1750 mm g) Oil temperature display on the oil tank h) Pressure adjustment from 5 T to 17 T (adjustable via rotary control) i) Two-speed hand lever operation j) Machine body powder-coated, or double painted k) Control cabinet supply cable from above with 3000 mm cable and 16 ampere plug l) Installation, commissioning, instruction against separate charge Press type single-column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. ( at 250 bar ) 150 kN Free tear-off force max. 10 kN Pressure build-up time Closed tool Stee ...

Stock number: 3754 HYDRAULIC PRESS Manufacturer: STENHOJ, Type: 25T TE Machine NO.: 54718, Year of construction: 1988 Specifications: Table size 620 x 380 mm Stroke length 300 mm pressing force 25 ton Weight: 1600 kg

Fortuna dough dividing and warp knitting machine Type: A4 Roll Press Division of 30 Weight range dough pieces 32-120 grams Dough insert per ratchet 960-3600 grams Year of construction: 2015 electric head including 3 knitting plates The robust design and duration of the oil cracking of the transmission parts ensures a long service life Easy cleaning even of the cutter head 380V / 50Hz Weight of the machine approx. 540 kg Trade-in and delivery on request Option for a complete overhaul of the machine Dimensions:  Height: 150 cm Width: 70 cm Depth: 70 cm

immediately available CNC press brake YAWEI PBH160/3100-4C - Pressing force: 1600KN - bending length: 3100mm - Year of construction 2022 - CNC controlled hydraulic crowning - Cybelec Modeva 19T control - WILA upper tool clamping - 60mm table with 13.5mm x 22mm groove for insertion matrices - 2 front support arms movable on linear guide - CE with Fiessler AKAS IIF (automatic height adjustment) - 24 months warranty - Commissioning, training

Veneering press OMC PL 105 LC 30/13 Water Work surface 3000x1300mm Opening width 400mm 6 cylinders with a diameter of 85mm Total pressure 105T Maximum heating temperature 85 degrees Control system logic contorl Machine control from touch panel readings Temperature, pressure force, shelf opening time, loading area calculator, programming of gluing processes Power 21KW CE Certificate Production 2023 Machine available on request New machine Net price

Hydraulic press

SPECIFICATIONS: Hydraulic press for bent elements Dimensions of the work table mm: 3000 x 1600 Number of pistons: 2 diameters Ø 200 mm Piston stroke mm: 1400 -Fence -Oil pump - 02 Steam outlet openings

Manesty D3B tablet press Serial: 24D117 Manesty 16 station tablet press, up to 500 tablets per min, max tablet diameter 25mm, max depth to fill 20mm, 3Ph

Manesty D3B tablet press Manesty 16 station tablet press, up to 500 tablets per min, max tablet diameter 25mm, max depth to fill 20mm, 3Ph

Hydraulic press brake Manufacturer: MENGELE Type: A 100-2 Pressing pressure: 100t Stroke: 160mm electr. Connection: 400V 3Ph Year of construction: 1964 Condition: used and functional

clamping force: 350 kN injection volume: 59 cm³ screw diameter: 25 mm platen size: 400 x 400 mm Condition: used, Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit: - clamping force: 350 kN - clamping platen size: 400 x 400 mm - Clear distance between tie bars: 270 x 270 mm - Mould installation height min.: 225 mm - Distance between clamping platens: max. 550 mm - Opening stroke max.: 325 mm - Ejector stroke: 125 mm Injection unit: - Screw diameter: 25 mm x 20D - Injection volume max.: 49 cm³ - Injection part weight: 59 g/hp - Max. injection pressure: 1,860 bar - Screw circumferential speed: 37 m/min - Cylinder heating: 4x 900 W - Nozzle heating: 300 W - Heating complete: 4,6 kW - Pump motor: 11 kW - Total power ...

Compact small briquetting press CA 10-15 KG/H Diameter of the briquettes approx. 55 mm 2.6 KW POWER CONSUMPTION V 230/50 CAN BE OPERATED WITH HOUSEHOLD ELECTRICITY BUT ALSO OPERABLE WITH V400/50 AND ZERO-WIRE PLUG ADJUSTABLE PLIERS Machine for do-it-yourselfers or small craft businesses Space requirement approx. .170x50x100cm, Weight 90kg

Standard Equipment's Chrome Coated Cylinder Boiled Steel Body Pressure indicator Pressure Adjustment User guide 2 Years Warranty CE

Pressing force 1000 kN Table size 750 x 560 mm, diarrhoea opening 100 mm Installation height 800 mm, stroke 500 mm Projection 360 mm Bear size 530x400 mm, 2 T-slots Ram speed: down 200 mm/sec, up 400 mm/sec Connection load approx. 21 kW Incl. Feeder WE16 for 160 mm bandwidth Coil tray and straightening unit Fabr. OFFICE; Type CA200/R40-7, YOC 1994 Reel, loop control Two-hand operation Manuals

Stock number: 3768 CNC PRESS BRAKE Manufacturer: DONEWELL, Type: 100 x 3000 Machine NO.: 588 12 2348, Year of construction: 1988 Specifications: Size bending length 3100 mm Size Printing capacity 100 tons Stroke length 215 mm Stand passage 2600 mm Projection 265 mm Bending speed 420 mm/min Hydraulic. CNC control Cybelec EURO III Fabr. Controlled in Y1-Y2-X Achen Program-controlled backgauge. X - 500 mm Accessories: Segment-split upper tool 3100 mm Multi bottom tool 3100 mm Operating manuals Length: 1300 mm, Height: 2450 mm, Width: 3100 mm, Weight: 7000 kg

Diaphragm press Friz type MFP 15/27 • Cover table size (mm): 2700 x 1500

Used SMG HZPUX 350/200 - 1500/1300 moulding press in good condition! Main technical data: - Power: 510 ton - Maximum span with castle: 1460 mm - Minimum light with castle: 520 mm - Maximum span without castle: 2160 mm - Minimum light without castle: 1220 mm

Eccentric Press Brand Ebu Type EP15 Table size 400x430mm Max pressure 15 000kg Table height adjustment Table passage D160mm Stroke adjustment 4-70mm Ram bore 40mm Projection 200mm Max distance table-tappet 320mm Single/Duration Stroke Shield Flywheel D600mm 400V 1.0kW Machine weight ca. 870 kg The purchase price is net. Can be viewed and tested in our warehouse. Delivery is possible at an additional cost. All information without guarantee!

automatic baler Manufacturer: HSM Type: VK 42/800 Year of construction: 2002 specifications: Pressing force: 42 t Channel format: 700 x 800 mm (W x H) Binding: 4-fold horizontal Filling opening: 800 x 650 mm Drive power: 30 kW Optionally with conveyor belts

Here are the technical data of the offered machine: Technical data + information: • No-load speed up to 40 mm/sec • Opening speed up to 40 mm/sec • Starting press speed 5–15 mm/sec • Table size/heating plate size 600 × 600 mm • Plunger size/heating plate size 600 × 600 mm • 2 heating plates, electrically heated, up to 250 degrees – as OPTION • Total size approx. 2000 × 1000 × 2800 mm height • OIL temperature monitoring • Automatic lubrication • Free positioning of the plunger • SICK/LEUTZE light barriers 14.1 mm on the front • Circulating oil cooling • Pressure holding valve 0 to 1800 sec. • Rear monitored door • Pressure adjustment from 30 T to 120 T • Travel limitation either by pressure or position • Programming set-up mode, single stroke (adjustable via rotary switch) • Control panel permanently installed in the wall  ...

Type / type: N 25 Year of make: 1977 Manufacturer / make: Weingarten Rated pressure: 25 t Number of strokes: 140 / min Radius slide center to frame: 200 mm Window in frame: 240 mm distance table slide: 250 mm Stroke adjustment / adjustment of stroke: 8 ... 80 mm Ram adjustability/adjustment of ram: 50 mm Ram size / surface of ram: 355 x 220 mm Table size / surface of bed: 560x 400 mm Hole in table: 160 mm Power of main motor:3 kW Weight / weight: 2,23 t

Specifications: Capacity: 60 t Passage between stand: 820 mm Working area, max.: 820 x 300 mm Piston stroke: 400 mm Flow speed: 6.1 mm/s Return speed: 10 mm/s Motor power: 3 kW Width: 1460 mm Depth: 850 mm Height: 2400 mm Weight, approx.: 700 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design made of welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Specifications: Capacity: 100 t Passage between stand: 1010 mm Working area, max.: 1010 x 300 mm Piston stroke: 400 mm Flow speed: 7.12 mm/s Return speed: 13.42 mm/s Motor power: 4 kW Width: 1600 mm Depth: 850 mm Height: 2450 mm Weight, approx.: 1000 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design with welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Specifications: Capacity: 160 t Passage between stand: 1100 mm Working area, max.: 1100 x 350 mm Piston stroke: 400 mm Flow speed: 6.2 mm/s Return speed: 6.8 mm/s Motor power: 5.5 kW Width: 1640 mm Depth: 1000 mm Height: 2550 mm Weight, approx.: 1300 kg Equipment: - Laterally movable cylinder via rack, pinion and handwheel - Spacious work area - Height-adjustable table - Torsion-resistant design with welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

pressure: 160 t distance between columns: 850 mm stroke: 150 mm table surface area: 850x650 mm total power requirement: kW weight of the machine ca.: 7 t dimensions of the machine ca.: 2,5 x 2,5 x 3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

FEINTOOL GKP F 160 hydraulic press was built in Switzerland. The automatic fine blanking press combines several workpiece machining stages into one precise process and significantly saves time and effort. As a result of fine blanking, parts with a maximum thickness of 6 mm obtain a characteristic even surface and accurately defined edges that cannot be achieved with other machines. The FEINTOOL GKP-F hydraulic punching press features a robust, stable construction and a total force of 160 tonnes. Offered with the machine a sheet metal feeder with a maximum thickness of 6 mm and a width of 210 mm allows for completely automatic machining. The automatic punching press underwent extensive modernisation in 1999. The total weight of the GKP-F 160 press is 9000 kg. Technical data of the FEINTOOL GKP F 160 fine blanking press - maximum sheet metal thickness: 6 mm - maximum sheet metal wi ...

Specifications Maximum pressure: 9 tons Pressing force: 2.76 kg/cm² Bale size: 650x500x580 mm Power supply: 400V/4kW Year of construction: 1996 Productivity: approx. 3 bales/hr Machine is fully functional, after technical supervision.

used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 18 S Year of construction: 2013 Serial No.: 116398 Specifications: Pressing force: 18t Engine: 4 kW Connection voltage: 400/50 V/Hz Cycle time: 22 s Pressing time: 12 s Insertion opening: W x H 107 x 62 cm Height from floor: 98 cm Bale ejected: W x H x D approx. 110 x 70 x 70-80 cm Bale height adjustable Bale weight: 120 – 180 kg depending on the material to be pressed Machine width: 152 cm Machine depth: 95 cm Machine height: 197 cm Weight: 850 kg (Subject to errors in the technical data)

used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 25 S Year of construction: 2012 Serial No.: 1113653 specifications: Pressing force: 25 t Filling opening: 1,200 x 670 mm (W x H) Height from the ground: approx. 940 mm Split egg filling opening: 1,070 x 260 mm Bale size: 1,200 x 800 x max. 800 mm Bale weight: up to 250 - 320 kg Drive power: 5.5 kW Cycle time: approx. 24 sec. Pressing time: approx. 13 sec. Binding: 4-fold - vertical with poly strap Machine dimensions: 1,600 x 1,300 x 3,170 mm (W x D x H) Machine weight: 2,180 kg Transport height: 2,240 mm (Subject to errors in the technical data)

used cabinet press Manafacture: HSM Type: 155.1 VL Year of construction: 1998 Machine no.: 6118.114. 01217M Serial no.: 6118.01217 specifications: Pressing force: 18 t Filling opening: 1,100 - 590 mm Filling space - 1100 - 700 x 1130 mm Bale size: 1,100 x 700 x 950 mm Bale weight: 110 - 200 kg Drive power: 4 kW Binding: 4-fold - vertical Output: 4 - 8 bales/hour Machine dimensions: 1,450 x 926 x 2,270 mm (W x D x H) Machine weight: 940 kg (Subject to errors in the technical data)

used cabinet press Manafacture: HSM Type: VL 155.2 Year of construction: 08 / 2003 Machine No.: 6114.734. R Serial No.: 240141893 specifications: Pressing force: 16 t Filling opening: 1,100 - 590 mm Filling space - 1100 - 700 x 1130 mm Bale size: 1,100 x 700 x 950 mm Bale weight: 110 - 200 kg Drive power: 4 kW Binding: 4-fold - vertical Output: 4 - 8 bales/hour Machine dimensions: 1,450 x 926 x 2,270 mm (W x D x H) Machine weight: 940 kg (Subject to errors in the technical data)

Specifications Maximum pressure: 36 tons Pressing force: 46.75 tons/m² Duct cross-section: 700x1100 x reg mm Bale weight: 380 kg Power supply: 400 V/ 15 kW Year of construction: 2009-2010 Number of ties: 4 vertical Dimensions of the tailgate: 1030x1100 mm Weight: approx. 3.9 tonnes Bale tying: manual

Press Schüco Model 290124 Type 2 Specifications: •pneumatic • Operating pressure max. (bar): 8 • Weight max. (kg): 80 • Enclosed tool: included (see photos)

Rotary indexing table with 12 stations Automatic ejector three pressing stages Pressure capacity 1,000 KN Stroke 12-120 mm Stroke rate 30-60 1/min Plunger adjustment 80 mm Total weight 9,500 kg

automatic baler Manafacture: PAAL Type: PACOMAT IS Year of construction: 1993 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Duct format: 700 x 700 mm Filling opening: 800 x 650 mm Drive power: 18.5 kW Throughput: 80 m³/h with additional manual feed hopper Wire passage seen in the direction of pressing on the left side

Press for paper or plastic Pressing pressure 5 tons 400 V 16 A Length 80 cm Width 80 cm Height 2 m

Hand screw press, used Balancier, used Typ/ type: PSHZ 25/I Presskraft / rated pressure: 25 t Hub/ stroke: 250 mm Tischgrösse/ table size: 400x 500 mm Ram: 200 x 500 mm Tischöffnung / hole in table: 140 mm Weight/ weight: 0,9t

Universal stamping machine Max impact power 50 KN Total stroke 80 mm Stroke sequence per hour 1500 Pneumatic Data

Inv. Num. : 6700 Type: 3000 kN Producer: Loire Created: 1992 GO 2008 Parameters: Control system: SIEMENS SIMATIC OP17 Compressive force: 3000 kN Table length: 2495 mm Table width: 1505 mm Maximum distance between the table and the ram (when the ram is low): 1200 mm Stroke: 800 mm Working speed: 64 mm/s

Inv. Num. : 6701 Type: 4000 kN Producer: Hydraulico Created: 1977 Parameters: Control system: SIEMENS SIMATIC OP Compressive force: 4000 kN Stroke: 800 mm Table height: 680 mm

pressure: 20 t throat: 185 mm stroke: 100 mm table surface area: 380 x 350 mm dayligth: 250 mm table height over floor: 840 mm total power requirement: 4 kW weight of the machine ca.: 1,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

FRITZ MÜLLER ZE 625-4 hydraulic press was built in Germany by Fritz Müller GmbH & Co. KG. The machine has been continuously maintained and upgraded throughout its service life. The first major overhaul was carried out in 1988 by the manufacturer’s service Machinenfabrik Mueller-Weingarten AG. A second overhaul was carried out in 2020, during which the press was brought up to current safety requirements. As part of this overhaul, a new control system based on a SIEMENS SIMATIC S7 PLC controller and a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel was installed, the entire electrical system was replaced, seals were replaced and light curtains were installed. The FRITZ MULLER ZE 625-4 is an extremely versatile press designed for even the most demanding metal forming operations. It is capable of performing operations such as deep drawing, stamping, forging, straightening large w ...