126,696 used machines on RESALE, but how to find them? Machine Search
Machine data: Press force: 3,000kN Roller diameter: 850mm Working width: 400mm Briquette dimension: 38 x 32 x 16mm Briquette volume with 4mm gap: approx. 16cm³ Briquette weight: approx. 38g Throughput capacity: 30,000kg/h Rated speed: 17.9/min Circumferential speed: 0.79m/s
1- one combination of lay-up, turning and unloading 2- BTF Multifoiler 3- Multi-Pin-System Useful area 1330x2630 mm Max size of board 1250x2550 mm Min foil width 1400 mm
Nominal Power: 400 ton Stroke par minute: 16-48 Adjustable stroke: 10-250 mm Table dimension: 1200 x 1200 mm Ram dimension: 1200 x 1200 mm Distance table – slide: 1000 mm Adjustment slide : 200 mm Motovariator: 22-66 HP
Max pressure: 150 ton Table size: 620 x 600 mm Between columns: 620 mm Lower and upper table are heated Max temperature: 200° C Weight: 8 ton
Max pressure: 120 ton Table size: 450 x 500 mm Between columns: 450 mm Lower and upper table are heated Max temperature: 200° C
Offer 25100 Specifications: - Pressure capacity 200 t - Working width 3050 mm - Passage between the uprights 2550 mm - Table width 180 mm - Projection 250 mm - Installation height 400 mm - Feed speed 80 mm/sec. - Working speed 6.7 mm/sec. - Retraction speed 67 mm/sec. - Plunger stroke 150 mm - Adjustment range fixed stops 120 mm - Drive 400 V 14.5 kW - Space requirement approx. W 3800 x H 2980 x D 1700 mm - Weight approx. 11500 kg - with: - Back gauge with 2 stop fingers - Deer's foot tool - 4-fold universal die - Two-hand control panel, foot switch,
2 presses Max pressure: 50 ton Table size: 400 x 500 mm Between columns: 400 mm Lower and upper table are heated Max temperature: 200° C
2 presses Max pressure: 60 ton Table size: 350 x 350 mm Lower and upper table are heated Max temperature: 200° C
Max pressure: 250 ton Table size: 620 x 600 mm Between columns: 620 mm Max opening: 500 mm Lower and upper table are heated Max temperature: 200° C Height: 2600 mm Weight: 6 ton
2 presses Max pressure: 120 ton Table size press left: 450 x 450 mm Between columns: 450 mm Max open: 285 mm Table size press right: 480 x 500 mm Between columns: 480 mm Lower and upper table are heated Max temperature: 200° C Weight: 5 ton
Max pressure: 120 ton Table size: 500 x 500 mm Between columns: 500 mm Lower and upper table are heated Max temperature: 200° C Weight: 3 ton
Max pressure: 150 ton Table size: 500 x 500 mm Between columns: 500 mm Lower and upper table are heated Max temperature: 200° C Weight: 4,5 ton
Max pressure: 400 ton Table size: 1000 x 650 mm Between columns: 1000 mm Lower and upper table are heated Max temperature: 200° C Height: 2600 mm Weight: 9 ton Capacity: 400 ton
SPECIFICATIONS: Briquettes: Ø 60 mm Production: 70 kg/h Installed power: 7.5 kW EQUIPMENT: 1 mini silo
Ajax 1,000 Ton Straight Side Mechanical Forging Press S/N 4410 10” Stroke 33” Shut Height 36” x 36” Bed 80 Strokes Per Minute Partially Rebuilt Ajax 1,000 Ton Straight Side Mechanical Forging Press S/N 4621 10” Stroke 32” Shut Height 36” x 32” Bed 80 Strokes Per Minute Bolsters are included. Both presses are in working condition and under power.
Offer 24591 Specifications: - Max. pressing force 25 t - Max. ram stroke 500 mm - Lifting speed 0 - 40 mm/s - Return 0 - 200 m/min - Installation height 800 mm - Projection to the middle of the ram 360 mm - Pusher clamping surface 440 x 360 mm - Plunger clamping pin 40 mm - Table size 630 x 500 mm - Table height above floor 710 mm - Thermoforming force 10 t - Largest deep-drawing depth 160 mm - Drive 400 V / 4 kW - Space requirement approx. W 800 x H 2720 x D 1150 mm - Weight approx. 2500 kg
Control SAFAN ... TS 1 Thrust... 50t Bending length ... 2550mm controlled axes ... 4 Drive... Electric Max. ram stroke ... 215mm Main engine power ... 9kW Machine weight ... 5050kg The machine is in good condition, possible to test under power.
SPECIFICATIONS: Installed power: 9.2 kW Briquette size: Ø 70 mm Complete with 13 filter bags (Ø 160 x 550 mm)
-) Press surface: 3,100 x 1,600 mm -) Cylinder: 8 cylinders -) Floors: 5 floors, 6 heating plates -) Heating plates: drilled 40mm steel heating plates -) Heating: for hot water or thermal oil (up to 200° -) Press opening: up to 600 mm -) Cooling: with own unit Etc.
Maplan 250ton Injection Machine Injection MTF 1500/250 Platen size = 630mm x500mm Stripper plate/ejectors =top only Max gap between platens = 702mm Volume = 1500 ccm3 Tonnage = 250T Year 2007
Maplan 160ton Injection Machine Injection MTF 750/160 Platen size = 510mm x 450mm Stripper plate/ejectors =top only Max gap between platens = 575mm Volume = 750 ccm3 Tonnage = 160T Year 2002
Pressing and joint-setting machine Book height : 100 - 520 mm Book width : 120 - 450 mm Book thickness : 6.5 - 100 mm Output : approx. 150 books/hour (depending on the material used)
Key data: 80 t, 400 mm, 112 mm
Printing capacity: 80 ton Table surface: 750 x 550 mm Plunger adjustment: 80 mm Stroke length: 8 - 112 mm Stroke rate: 78 p/min. Projection: 400 mm Equipped with: - Air coupling - Safety screen Country of origin: Germany Motor power: Machine LxWxH: 2000 x 1200 x 2900 mm Machine weight approx.: 7000 kg
HYDRAULIC PRESS with hot platens model ITALPRESSE SCF 6 second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.70 max. thrust Ton. 120 opening mm. 400 hydraulic pump motor power Hp 3 hot water plates heating via wood boiler weight kgs. 4500 volt. 380/50
! Exhibition Machine Corresponds to the Panhans LLB116 with the following optional accessories: - Single-lever operation with fine locking - Dial gauge in the handwheel for height adjustment SPECIFICATIONS: - Max. drilling depth 145 mm - Max. elongated hole length 240 mm - Height adjustment 135 mm - Motor power 1.3/1.7 kW - Suction nozzle Ø 100 mm - Machine weight 200 kg
! Exhibition Machine Equipment/Technical Data Work table mm 800x400 Motor kW 1.5/1.9 kW Spindle speed rpm 1440 / 2880 Max. slotted hole height above the table mm 160 Max. longitudinal work run mm 345 Max. transverse work run mm 245 Spindle stroke mm 160 Clamping Ø of tool mm 0 - 20 Max. tool length mm 175 Span Center Piece 2 Rotating table ° +/- 45° Dimensions of the machine mm 1500x1100x950 Machine weight kg 345 Other features: - Mechanical dowel device, distance 16-22-25-32 - Mechanically numerical spindle height display - Suction nozzle
Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.
FETTE Data Control 2 Installed in a mobile cabinet including an EPSON printer
COURTOY R292F Compressor Missing the 2 compressed descents and the cables between the electrical cabinet and the machine; All the documentation including the electrical diagrams is present (in French), Punch type: D, Weight (kg): 4500 , Cadence / hour: 43,000 - 350,000, Compression (kN): 100, Precompression (kN): 10, Maximum tablet dimensions (mm): 25,40, Die outer diameter (mm): 38,10, Matrix height (mm): 23,81, Punch diameter (mm): 25,40
pressure: 20 t stroke: 180 mm daylight between the columns: 540 x 100 mm dayligth: max. 990 mm : 72 mm diameter of piston: 48 mm weight of the machine ca.: 0,12 t dimensions of the machine ca.: 0,8 x 0,7 x 1,8 m Our frame presses are officially CE certified according to the latest rules. Almost all presses offered in this area are not CE certified. - with manual hydraulics - Move the cylinder sideways - Pressure gauge - 2 press documents The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 10 t stroke: 180 mm daylight between the columns: 335 x 115 mm dayligth: max. 340 mm : 56 mm diameter of piston: 40 mm weight of the machine ca.: 0,05 t dimensions of the machine ca.: 0,75 x 0,53 x 1,6 m Our frame presses are officially CE certified according to the latest rules. Almost all presses offered in this area are not CE certified. - with manual hydraulics - Move the cylinder sideways - Pressure gauge - 2 press documents The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Container Press SMC/CP 1100 Used Equipment Used device is kpt. reconditioned, wear parts were replaced, incl. oil change and new hydraulic hoses incl. UVV safety test and protocol, 6 months warranty Pressing force: 3.5 tons Swivel stroke: 95 degrees Connected load: 230 V/ 1.5 KW Machine dimensions: 980x 1190x 1900 mm WxDxH Machine weight: 250 kg
Upstroke press Top lid can tilt open to allow mould to be (un)loaded Capacity: 150 ton Passage between uprights: 1850 mm Max ram adjustment: 500 mm Distance between table -- ram: 1000 mm Table area: 1800 x 1300 mm Height: 2350 mm
Jörgensen tablet press type 075HK3, built in 1961, with accessories, poor condition
Inv. Num. : 8437 Type: 50-VE Producer: IMS Created: 2002 Parameters: Compressive force: 50 t Maximum stroke rate per minute: 145 1/min Stroke: 80 mm Adjusting the ram: 75 mm Machine weight: 2300 kg
Inv. Num. : 8438 Type: AF-200-75 Producer: Arisa Generated: Parameters: Maximum retraction speed: 200 t Top table length: 950 mm Top table width: 750 mm Maximum number of strokes: 20 1/min Ram stroke: 250 mm
FOR SALE: BRUDERER BSTA 50USL High-Speed Stamping Press With Automatic Strip Feeder BBV 190 500 kN | 100–1120 spm | Fully automatic | Top-tier Swiss quality Technical Highlights: Nominal force: 500 kN Stroke rate: 100–1120 strokes per minute Working hours: 41000 h Main motor: 22 kW Control voltage: 24V DC Power connection: 400V / 50Hz / 62 kVA Adjustable stroke: 16 / 19 / 25 / 32 / 38 /44 / 51 mm Shut height adjustment: 64 mm Working Dimensions: Max tool installation width: 1100 mm Strip pass width: up to 256 mm Ram area: 980 × 420 mm Table area: 1080 × 650 mm Strip entry height adjustable: 60–140 mm Max strip width: 120 mm Max feeding pitch: 85 mm Max material thickness: 4 mm Feeding angle: 180 Deg Machine Dimensions (with BBV 190): Machine footprint (L × W × H): 2407 × 1278 × 3150 mm Weight (approx.): 8,000 kg Equipment Includes: Feeder BBV 1 ...
Technical data SCREW PRESS DELLAVIA mod. BRINDISI Brand DELLAVIA Modell Brindisi Screw diameter 180 mm Nominal Power 340 ton Max allowable power 550 ton Light between the uprights under the guides 460 mm Light between the uprights within the guides 350 mm Table dimension 430 x 550 mm Table distance under the guides 445 mm Overall dimension 3710 x 2590 x 1890 mm Power 20 Kw Weight 9 ton
Gluing press Emmes Type: H EBP 500 . 10 Working length 5000 mm Working height 1530 mm Support width or depth 150 mm 10 Hydraulic Vertical Press Punch 5 pneumatic front hold-down devices max. compressive force 150/cm² Hydraulic pump 2.2 kW Oil pressure 159 kg/cm Air pressure 8 kg/cm²
Specifications Maximum pressure: 75 tons Year of Make: 1999 Press force: 90.9 t/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1100 mm Dimensions of the tailgate: 1020 x 1550 mm Bale weight: 500-750 kg Weight: approx. 25 tons Power connection: 400 V Bale tying: automatic Motor: 75 kW (possibility of switching to 55 or 45 kW) Press capacity at idle: max 750 m³ / hour Press capacity under operating conditions: max 350 m³ / hour Theoretical throughput to density 35 kg/m3: approx. 12 tons/hour Theoretical throughput to density 60 kg/m3: approx. 21 tons/hour Theoretical throughput to density 100 kg/m3: approx. 33 tons/hour Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the channel. Automatic binding with wire Cho ...
Brand: DELLAVIA Model: Livorno Screw diameter: 125 mm Maximum allowable pressure: 200 tons Clearance between uprights below the guides: 320 mm Clearance between uprights within the guides: 240 mm Ram stroke: 280 mm Table dimensions: 300 x 400 mm Distance from table to guides: 230 mm Overall dimensions: 1.430 x 1.050 x 2.980 mm (H) Approx. weight: 2.900 kg
Used piston press for apple juice production made by Bucher, model: HP 5000, capacity 5 t / h. New: 1985. 2 pieces available for general renovation (hydraulics) or for parts. Control cabinet available for 1 press.
Qty. 1 Second-hand aluminium extrusion press line Code Aluminium HE9 6063 Mfc.: Indian manufacturer Built: 1978 PLC hydraulic – upgradation done in the year 2005! Total Force of Press: 680 MT, 750 UST Extrusion Pressure: 210 Bar Billet Diameter: 5”, 121 mm Weight per Inch of Billet: 0.76 kg/inch Scope of supply: Log heating furnace Hot shear Extrusion press Overhead puller Under-bed cooling system Run-out cooling bed Belt conveyor Stretcher Cutting machine Die oven Conveyor table Conveyor for final packaging
Camu decoiler 3 ton Dimeco straightener - 800 x 1,1 mm - 11 x 60 mm straightening rolls - 4 x 60 mm feeding rolls - weight: 850 kg CNC mircrofeeding unit Pressix excentric press - 100 ton - 65 strokes/min - adjustable stroke: 10 gt; 130 mm - table: 950 x 660 mm - max opening: 370 mm
Offer 25227 Specifications: - Pressure capacity 150 t - Working width 3600 mm - Passage between the uprights 3150 mm - Table width 180 mm - Projection 250 mm - Installation height 325 mm - Feed speed 70 mm/sec. - Working speed 7 mm/sec. - Retraction speed 60 mm/sec. - Ram stroke 120 mm - Adjustment range fixed stops 120 mm - Motor power approx. 7.5 kW - Oil filling approx. 300 l - Space requirement approx. W 3850 x H 2300 x D 1600 mm - Weight approx. 8700 kg - with: - Swivel arm – control panel with ATL 550 control - For crimping depth + backgauge -Mot. Backgauge - Crowning device - Lasersafe FIESSLER - 4-fold universal die, split sharpening tool + deer's foot tool - Two-hand control panel, foot switch,
Offer 25200 Specifications: - Pressure capacity 200 t - Working width 3100 mm - Passage between the uprights 2600 mm - Table width 180 mm - Projection 300 mm - Installation height 450 mm - Feed speed 80 mm/sec. - Working speed 9 mm/sec. - Retraction speed 60 mm/sec. - Ram stroke 120 mm - Adjustment range fixed stops 120 mm - Drive 400 V / 18.7 kW - Space requirement approx. W 3300 x H 2950 x D 1900 mm - Weight approx. 10500 kg - with: - Adjustment of the crimping depth + baling pressure -Mot. Backgauge with handwheel fine adjustment - 4-fold universal die - sharpening tool - Two-hand control panel, foot switch,
SPECIFICATIONS: Working width: 3000 mm Working height: 2500 mm 4 push-button plate suspension handles TS/500 Interface 4 safety light barriers Installed power: 3 kW
High: 2.050 mm, Long: 750 mm, Force: 10 tons, Width: 600 mm, Weight: 800 Kg., Neckline: 150 mm, Stem travel: 200 mm, Rate of climb: 10 cm / sec, Piston rod ø of: 65 mm, Surface of the table: 300 x 300 mm., Specification: Hydraulics
maximum number of results exceeded
please refine your search
