126,611 used machines on RESALE, but how to find them? Machine Search
used
Beyeler RH 100 ton x 3100 mm Capacity: 100 ton x 3100 mm Backgauge: manual Passage between uprights: 2630 mm Max stroke: 215 mm Max distance between table -- ram: 410 mm Depth of throat: 255 mm Locking speed: 100 mm/sec Working speed: 6,5 mm/sec Electric motor (power): 5,5 kW Length: 3300 mm Depth: 1550 mm Height: 2450 mm Weight: 7 ton
An old Künstner & Hampel eccentric press is available. Pressure capacity: 25 tons, power requirement: 2.5 HP. On-site inspection is possible.
LVD PPBL 200 ton x 4100 mm Capacity: 200 ton x 4100 mm Backgauge: manual Passage between uprights: 3150 mm Max stroke: 150 mm Max distance between table -- ram: 400 mm Depth of throat: 250 mm Table width: 200 mm Locking speed: 100 mm/sec Working speed: 6,5 mm/sec Returning speed: 65 mm/sec Electric motor (power): 11 kW Weight: 13,4 ton
A high-performance cold press is available for pre-pressing diamond segments in tools. Main cylinder: 2, cylinder diameter top/bottom: 100mm/100mm, cylinder stroke top/bottom: 180mm/150mm, max. operating pressure: 300bar, press force: 235kN. Die clamping cylinder: 2, piston diameter: 63mm, cylinder stroke: 15mm, max. clamping force: 62kN, max. operating pressure: 200bar, piston area: 31.2cm². Weighing stations: 2, weight range: 1g-50g, accuracy: +/-0.05g, powder hopper volume: 12l. Machine dimensions X/Y/Z: approx. 1800mm/1000mm/1900mm, weight: approx. 2000kg. Documentation available. On-site inspection is possible.
Maplan 250ton Injection Machine Injection MTF 1500/250 Platen size = 630mm x500mm Stripper plate/ejectors =top only Max gap between platens = 702mm Volume = 1500 ccm3 Tonnage = 250T Year 2007
Max. Press force: 1000kN, max. retraction force: 110kN, max. stroke: 360mm, max. working pressure: 251bar, installation height: 560mm, control panel: Siemens SIMATIC OP27, weight: 7.5t, on-site inspection is possible.
Maplan 160ton Injection Machine Injection MTF 750/160 Platen size = 510mm x 450mm Stripper plate/ejectors =top only Max gap between platens = 575mm Volume = 750 ccm3 Tonnage = 160T Year 2002
Four Neff single-column presses are available. 1) Neff T 6.3, year of manufacture: 1989, output: 3kW. 2) Neff single-column press, operating hours: 9097h. 3) Neff EP 10 single-column press, year of manufacture: approx. 1950. 4) Neff single-column press. On-site inspection is possible.
Key data: 80 t, 400 mm, 112 mm
Printing capacity: 80 ton Table surface: 750 x 550 mm Plunger adjustment: 80 mm Stroke length: 8 - 112 mm Stroke rate: 78 p/min. Projection: 400 mm Equipped with: - Air coupling - Safety screen Country of origin: Germany Motor power: Machine LxWxH: 2000 x 1200 x 2900 mm Machine weight approx.: 7000 kg
Working dimensions X/Y: 3000mm/2000mm, cylinder stroke: 1000mm, height adjustment: 2000mm-2600mm, length adjustment: 3000mm-6000mm, pressing force: 2t, space requirement: 4100mm/1000mm/2450mm, weight: approx. 1500kg. Documentation available. On-site inspection is possible.
Key data: 110 t, 3100 mm, 2550 mm
Printing capacity: 110 ton Bending length: 3,100 mm Stand width: 2,550 mm Back gauge: 1,500 mm Stroke length: 150 mm Projection: 250 mm Feed speed: 100 mm/sec. Working speed: 8 mm/sec. Retraction speed: 65 mm/sec. Control: ESA Kvara S630 Touch Equipped with: - Foot pedal - Various tool sets - Light curtain safety Merlino - Controls renewed in 2018 Country of origin: Netherlands Motor power: 7.5 kW Machine LxWxH: 320 x 160 x 244 cm Machine weight: 8,700 kg
Key data: 300 t, 4300 mm, 3700 mm
Printing capacity: 300 ton Bending length: 4,300 mm Stand width: 3,700 mm Back gauge: 550 mm Stroke length: 300 mm Projection: 450 mm Feed speed: 120 mm/sec. Working speed: 10 mm/sec. Retraction speed: 120 mm/sec. Control: Delem DA65 Equipped with: - Y1, Y2, X&R - Axis Controlled - CNC hydraulic crowning - Various sets of bending tools - Safety light cabinet Lazer Safe - Operating instructions and machine documents Country of origin: Netherlands Motor power: 30 kW Machine LxWxH: 510 x 200 x 330 cm Machine weight: 21,500 kg
HYDRAULIC PRESS with hot platens model ITALPRESSE SCF 6 second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.70 max. thrust Ton. 120 opening mm. 400 hydraulic pump motor power Hp 3 hot water plates heating via wood boiler weight kgs. 4500 volt. 380/50
Manufacturer: Feintool Model: GKP-F 160 Type of Machine : Fineblanking Press Revision Year: 2003 Total Force: 1600 kN Head Pressure: 10 - 400 kN Table Pressure: 10 - 500 kN Stroke Rate: 20 - 70 strokes per minute Operating Voltage: 3x400V, 50Hz, N + PE Control Voltage: 24V Power: 22 kW year 1975 but had was completely refurbished in 2000 Find more here - / Contact us at -
FETTE Data Control 2 Installed in a mobile cabinet including an EPSON printer
Manufacturer: Feintool Model: GKP-F 160 Type of Machine : Fineblanking Press Revision Year: 2003 Total Force: 1600 kN Head Pressure: 10 - 400 kN Table Pressure: 10 - 500 kN Stroke Rate: 20 - 70 strokes per minute Operating Voltage: 3x400V, 50Hz, N + PE Control Voltage: 24V Power: 22 kW Fully refurbished in year 2003 Find more here - / Contact us at -
Press capacity: 50 ton Ram stroke: 54 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 303 mm Table surface area : 810 x 550 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 7,5 ton Main Motor: 11 kW
! Exhibition Machine Corresponds to the Panhans LLB116 with the following optional accessories: - Single-lever operation with fine locking - Dial gauge in the handwheel for height adjustment SPECIFICATIONS: - Max. drilling depth 145 mm - Max. elongated hole length 240 mm - Height adjustment 135 mm - Motor power 1.3/1.7 kW - Suction nozzle Ø 100 mm - Machine weight 200 kg
! Exhibition Machine Equipment/Technical Data Work table mm 800x400 Motor kW 1.5/1.9 kW Spindle speed rpm 1440 / 2880 Max. slotted hole height above the table mm 160 Max. longitudinal work run mm 345 Max. transverse work run mm 245 Spindle stroke mm 160 Clamping Ø of tool mm 0 - 20 Max. tool length mm 175 Span Center Piece 2 Rotating table ° +/- 45° Dimensions of the machine mm 1500x1100x950 Machine weight kg 345 Other features: - Mechanical dowel device, distance 16-22-25-32 - Mechanically numerical spindle height display - Suction nozzle
LVD PPS-TS 100 ton x 3100 mm CNC Capacity: 100 ton x 3100 mm Backgauge: CNC Control: Cadman Express Passage between uprights: 2550 mm Max stroke: 150 mm Max distance between table -- ram: 350 mm Depth of throat: 250 mm Locking speed: 100 mm/sec Working speed: 10 mm/sec Returning speed: 80 mm/sec Electric motor (power): 16 kW
A dismantled Mecamaq hydraulic press is available. Pressing force: 100t, max. pressure: 290bar, main piston diameter: 200mm/120mm, auxiliary cylinder diameter: 40mm/25mm. Main cylinder working stroke: 500mm, max. installation height: 800mm, working height: 800mm, effective dimensions X/Y: 700mm/500mm, table dimensions X/Y: 800mm/500mm, working speed: 6mm/s, return speed: 150mm/s. Max. tool dimensions X/Y: 800mm/600mm, max. tool weight: 1000kg. Machine dimensions X/Y/Z: approx. 1000mm/1350mm/2750mm, weight: approx. 4000kg. Documentation available. On-site inspection is possible.
Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.
Key data: 50 t, 1600 mm, 200 mm
CNC Press Brake COLLY 502/A Numerical Command: CYBELEC type DNC 32 P-CM Capacity: Maxi length 2000 mm x 50 T Throat depth: 200 mm Distance between uprights: 1600 mm Back Gear Gauge 1 axe Defective cylinder Right cylinder joint to change Machine functional (only right cylinder joint to change) Voltage: 380 V Length: 2500 mm Depth: 2100 mm Total height: 2400 mm Weight: approx 4 T
fabric-no.: 202 395 working length: 2550 mm output: 2000 KN tracking travel: 13 mm safety distance: 176 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Vertical Multistage High Pressure Centrifugal Pump KSBTyp Movichrom N CN 3/10 2RFabr. Nr 1-P30-837561Nominal flow rate max. 3 m3/hNominal delivery head 70 meters = 7 barNominal speed 2900 rpm. Motor power 1.5 kWNet connection 400 volts, 50 Hz- pump structure in 10 stages- pump elements made of stainless steel, pump base made of cast iron connection flanges DN 32- suitable for drinking water supply, irrigation and drainageSpace requirement pump L x W x H 250 x 220 x 830 mmWeight 38 kgUnused replacement pump made of
Single-column eccentric press AMBOLD type PEEV 25.2Masch. No. 11734 / 02 Year of construction 2002Compressive force 25 ton. Projection 200 mmTable area 520 x 400 mmPlunger area 155 x 155 mmHole in table 185 x 155 mmStroke adjustment 4-80 mmPlunger adjustment 40 mmInstallation height max. 270 (largest stroke in UT, table below)Clamping pin hole 32 mmTable height adjustment approx. 150 mmPlunger strokes 160 strokes/min. Motor power 2.2 kWNet connection 400 volts, 50 Hz pneumatic clutch-brake combination
Double Column - Hydraulic Press RASTER ZEULENRODA (WALTER) Type WUP S 60Masch. No. 136 / 7 (156-165) Year of manufacture 1999Basic machine from 1987, in 1999 Overhauled with new controlPressure capacity 60 ton. Stand width 1090 mmStand passage laterally 265 mm (one-sided) Plunger area 650 x 300 mmAdditional plate on ram 990 x 550 x 60 mmTable area 990 x 550 mmPlunger stroke max. 320 mmInstallation height 330 or 390 mmTable height above floor 980 mmHydraulics Operating pressure 320 barRapid traverse downward 75
A Bruderer differential stroke press (knuckle-joint press) is available. Press force: 3200kN, installation height min./max.: 420mm/520mm, clamping table dimensions X/Y/Z: 1400mm/1000mm/150mm, table height: 1030mm, ram dimensions X/Y: 1000mm/800mm, belt passage width and height: 400mm/450mm, machine dimensions X/Y/Z: approx. 2350mm/1850mm/4550mm. Documentation available. On-site inspection is possible.
pressure: 63 t distance between columns: 650 mm stroke: 200 mm total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Pressing force: 440kN, working width: 1600mm, cylinder stroke: 150mm, travel X/R: 400mm/200mm, adjustment speed R-axis: 200mm/s, installation height: 400mm, throat depth: 200mm, machine stand distance: 1530mm, motor power: 7.5kW, weight: approx. 2100kg. Including various accessories and tools. Documentation available. On-site inspection is possible.
pressure: 500 t passage width: 750 mm stroke: 120 mm total power requirement: 57 kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A roller press (briquetting press) Köppern Maco is available. Production capacity: 10 MT/h, roller diameter: 720mm, roller width: 315mm, briquetting shapes: bolted segments, motor type: Siemens electric motor, motor power: 190kW, gearbox type: spur gear, machine dimensions X/Y: approx. 5000mm/5000mm, weight: approx. 15000kg, control: Siemens S7-300 Simatic. Including two new segment sets and one installed segment set. Documentation available. On-site inspection is possible.
A Sahinler workshop press is available. Press pressure: 150t, max. pressure: 244bar, working width: 1520mm, piston stroke: 300mm, ram dimensions X/Y: 200mm/1520mm, through hole: 100mm, table dimensions X/Y: 600mm/1520mm, max. installation height: 610mm. Forward speed: 9mm/s, retraction speed: 10mm/s, working speed: 5mm/s, drive power: 11kW. Machine dimensions X/Y/Z: approx. 2500mm/1000mm/2400mm, weight: approx. 3000kg. Documentation available. On-site inspection is possible.
Pressing force: 2000kN, max. stroke: 400mm, throat depth: 300mm, ram table distance: 965mm, ram speed forward/reverse: 100mm/s, working speed: 10mm/s, table width: 1700mm, working length: 2600mm, working height: 1080mm, column distance: 2300mm. Machine dimensions X/Y/Z: approx. 3750mm/2600mm/3600mm, weight: approx. 17500kg. On-site inspection is possible.
pressure: 75 t throat: 280 mm stroke: 303 mm total power requirement: 15 kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Pressing force: 2000kN, working width: 3100mm, column passage: 3240mm, max. stroke: 400mm, throat depth: 250mm, max. installation height: 965mm, NC axes: 11, hydraulic volume: 550l, machine dimensions X/Y: approx. 4400mm/3400mm, weight: approx. 16600kg, control: Cyb-Tech Infinitron. Documentation available. On-site inspection is possible.
pressure: 25 t throat: 250 mm stroke: 100 mm total power requirement: 7,5 kW weight of the machine ca.: 3200 kg dimensions of the machine ca.: 1000 x 1700 x 2600 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Installation height: 408mm, max. working pressure: 315bar, max. pressing force upper piston/lower piston: 630kN/100kN, upper piston retraction force: 71kN, max. stroke upper piston/lower piston: 160mm/80mm, overtravel: 26mm, overtravel time: 106ms, safety distance: 169mm, hydraulic oil capacity: 250l, weight: approx. 3700kg, operating hours: 9283h. Documentation available. On-site inspection is possible.
pressure: 200 t passage width: NA mm stroke: 180 mm table length: 690 mm table width: 530 mm distance between columns: 420 mm total power requirement: 18 kW weight of the machine ca.: t dimensions of the machine ca.: m Hydr. 4-Pillar Press for Embossing/Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensional range: M6-M14, length range: 110mm, number of strokes min./max.: 110strokes/125strokes/min, max. wire diameter: 15mm, slide stroke: 160mm, pressing force: 100t, oil capacity: 70l, oil type: CLP 68, clutch manufacturer: Ortlinghs, air consumption at 30 operations/min: 800l/min, weight: approx. 23000kg.
pressure: 3 t throat: 0 mm stroke: 200 mm total power requirement: 15 kW weight of the machine ca.: 4 t dimensions of the machine ca.: m Fully Automatically Straightening Press, 3 Stations,parts turning, (bolts) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 10 t throat: 0 mm stroke: 400 mm total power requirement: 7,5 kW weight of the machine ca.: 6500 t dimensions of the machine ca.: m D U N K E S (Germany) CNC Controlled Hydraulic Double Column Press Model HD 10 Year 1993 ________________________________________________________ Pressure 10 tons Ram stroke 400 mm Mounting height 600 mm Table size 400 x 300 mm Table height above floor 820 mm Ram area 400 x 300 mm Ram bore 40 mm Quickspeed, downwards, max. 70 mm/s Working speed, downwards, using max. pressure 40 mm/s Working speed, min. 5 mm/s Working speed adjustable from 5 - 70 mm/s Return stroke speed, min./max. 20 / 175 mm/s Drive 7.5 kW Total electrical load, approx. 12 kW - 380 V - 50 Hz Weigh ...
Two identically constructed heated Ital presses are available. Press length: 1700mm, press width: 1500mm, press height: 1400mm, press force: 800kN, total connection: 30kW, machine dimensions X/Y/Z: approx. 5400mm/2300mm/3200mm. Including piston from above, fittings for chair seats and heating. Documentation available. On-site inspection is possible.
pressure: 63 t passage width: 1350 mm stroke: 300 mm total power requirement: 16 kW weight of the machine ca.: 10 t dimensions of the machine ca.: 2,0 x 1,8 x 3,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A total of five Cannon foam systems are available. Materials: isocyanates and polyol, press plate dimensions X/Y: 720mm/650mm, lid opening angle: 100°, tilt angle: 60°, opening min./max.: 312mm/502mm, parallel stroke: 190mm, approach stroke: 95mm, press stroke: 95mm, ejector stroke: 75mm, control: PLC. Including material preparation. Documentation available. On-site inspection is possible.
COURTOY R292F Compressor Missing the 2 compressed descents and the cables between the electrical cabinet and the machine; All the documentation including the electrical diagrams is present (in French), Punch type: D, Weight (kg): 4500 , Cadence / hour: 43,000 - 350,000, Compression (kN): 100, Precompression (kN): 10, Maximum tablet dimensions (mm): 25,40, Die outer diameter (mm): 38,10, Matrix height (mm): 23,81, Punch diameter (mm): 25,40
pressure: 500 t passage width: 750 mm stroke: 120 mm total power requirement: 57 kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 10 t distance between columns: 500 mm stroke: 200 mm total power requirement: 10 kW weight of the machine ca.: 4.500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Press capacity: 100 ton Ram stroke: 300 mm Slide adjustment: 125 mm Shut height (stroke down, adjustment up): 600 mm Free frontal opening L-R: 2.020 mm Free lateral opening F-B: 620 mm Table surface area : 2.000 x 1.000 mm Slide area: 2.000 x 900 mm Hole in table: 1.700 x 300 mm Number of strokes: 10 - 50 s.p.m. Table height over floor: 1.200 mm Required power: 39 kW Height over floor approx.: 4.400 mm Dimensions L x W x H: 5.166 x 2.500 x 4.400 mm Weight of machine approx.: 38 ton
maximum number of results exceeded
please refine your search
