press for frame used for sale

Vacuum press, vacuum table, vacuum membrane press, veneer press, laminate vacuum press -Handover: in its current condition as inspected -Condition: without vacuum pump -Vacuum press: on a mobile base -Sheet surface area: 1160 x 1210 mm -Dimensions: 1940/1640/H1135 mm -Weight: 637 kg

Piferoen type 5H baler complete with conveyor. Baling press 6.30m x 2m x 1.6m approx. Conveyor 7.5m x 1.2m x 0.80m approx.. Chamber size (WxDxH) 108 x 59 x 105 cm approx. Suitable for baling textiles and other products. Bales can be completely covered for protection of material.

Hand spindle press, mandrel press, spindle press, hand spindle press, printing press, balance printing press -Manufacturer: Allgaier, manual spindle press -Insertion height: 345 mm -Column clearance: 300 mm -Table width: 300 mm / Bore Ø 60 mm -Spindle mount: Ø 40 mm -Dimensions: Ø 1420 x 1780 mm -Weight: 277 kg

Nominal force: 2500 ton Ram stroke: 190 mm Number of strokes in 1 minute: 20 Shut height: 800 mm Bolster plate-to-ram adjustable stroke: 15 Table size: 1250x1400 mm Weight 124.230T

used canning press / packaging press Manufacturer: WAGNER Type: WDSP 7000 Year of construction: 1993 specifications: Pressing force: 70 t Specific pressing pressure: 318 kg/cm² Drive power: 15 kW / 400 V Duct format: 550 x 400 mm Filling opening L x W: 1,150 x 550 mm Compaction chamber: 700 x 550 x 400 mm Total stroke: 2,100 mm Machine length: approx. 5,500 mm Machine width: approx. 1,920 mm Capacity: approx. 1.5 t/h (depending on material) Package size, WxHxL: 550 x 400 x 280 - 550 mm Package weight: approx. 20 - 40 kg (depending on the setting of the package length) Machine weight: approx. 3,500 kg

Key data: 400 t, 800 mm

Oil-hydraulic double-column press 400 T with sliding table Press type: Double column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. 4000 kN Free tear-off force max. 400 kN Print build-up time Closed tool steel on steel Max. 4 sec. Dimensions: 3,800 mm long and 4,475 mm wide Max. opening width 800mm Stroke 800mm Table height above floor 1100mm Height above ground (height) approx. 4300 mm Hall height min. 5500 mm Parallel deviation at 20°C +/- 0.1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of the press without consumables and table top approx. 28 tons Press table Table size 1500x1500 mm Velocities Quick closing at 100 mm sec. Pressing speed 8 – 3 mm sec. Acoustic pressure Sound pressure level, measured at a height of 1.5m on the control pane ...

Hydraulic press, single-column high-speed press, C-column press, oil-hydraulic press - Pressing force of the ram: approx. 35 tons -Clamping table: 500 x 470 mm -Insertion height: 650 mm -Insertion width: 275 mm -Dimensions: 1300/900/H3200 mm -The machine can be dismantled to a height of: 2700 mm -Weight: approx. 1500 kg

Pressure testing device, measuring device -with trailing-pointer -Max. pressure: 20 bar -High-pressure hose -Dimensions: 400/160/H200 mm -Weight: 4 kg

Proportional pressure control directional control valves, solenoid valves, pneumatic valves, air valves, pressure valves, valve blocks, control blocks -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm -Weight: 2 kg

Pressure sensor -Type: 3405BM2X2X2920 -Measuring range: 0-250 bar G -Max. Pressure: 1034 bar G -Input: 10-30 VDC -Output: 4-20 mA -Number: 2x available -Price: per piece -Weight: 0.5 kg

Pressure regulator intermediate plate -Type: LR-ZP-A/B-D2 35428 -From: 0 bar to: 12 bar -Price: per piece -Quantity: 8x Available -Weight: 2 kg

Inv. Num. : 6992 Type: LKT 250 Producer: METALPRESS Created: 1963 Parameters: Ram stroke: 120 mm Plunger adjustment: 100 mm Machine weight: 2700 kg

Specifications Maximum pressure: 54 tons Power supply: 400V / 7.5 kW Press force: 5.62 kg/cm² Year of construction: 2005 Bale size: 1200x800x1200 mm Productivity: approx. 2 bales/hr Bale weight: approx. 500 kg Price: on request Machine is fully functional, after technical supervision. Price also includes paint renovation.

Hydraulic pressure switch -Type: TGL10952 -Adjustable: from 0 to 320 bar -Price: per piece -Number: 9 available -Weight: 0.5 kg

Proportional pressure control directional valve, solenoid valve, pneumatic valve, air valve, pressure valve, valve block, control block -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm -Weight: 2 kg

Specifications Maximum pressure: 12 tons Power supply: 380V/ 5.5 kW Press force: 2.5 kg/cm² Year of construction: 1985-1993 Bale size: 800x600x(600-1000)mm Productivity: approx. 3 bales/hr Bale weight: approx. 100 - 200 kg Price: on request Machine is fully functional, after technical supervision.

5/2 Pressure Booster -Type: DPA-40-10 537273 -VN: 43 -1: 2.5-8 bar 2: 4.5-10 bar -Weight: 1.5 kg

Proportional pressure control directional control valves, solenoid valves, pneumatic valves, air valves, pressure valves, valve blocks, control blocks -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm Price: per piece -Quantity: 2 available -Weight: 2 kg/piece

Hydraulic pressure switch, pneumatic pressure switch -Type: EDS 1100-050-1-009 -Pressure: 25 bar -Operating voltage: 24 VDC -Signal output: 0-5 VDC -Weight: 0.3 kg

Hydraulic pressure switch, pneumatic pressure switch -Type: EDS 1691-NC-016-000 -Pressure: 16 bar -Operating voltage: 24-20 VDC -Signal output: 4-20 mA Price: per piece Quantity: 2 available -Weight: 1 kg

Pressure valve, pressure gauge, pressure indicator, manometer -Measuring range: 0-6 bar -Fitting: Ø 63 mm -Thread: M12/1.5 mm -Price: per piece -Quantity: 10 available -Weight: 0.2 kg

Pressure switch -Type: C6045D 1043 -0.2-3 mbar -220/240 VAC 50 Hz 12(2) A -Pmax: 100 mbar -Protection class: IP 40 -Quantity: 3 pieces available -Price: per piece -Weight: 1.2 kg/piece

echnical characteristics Nominal force, mc 1600 Not reach the slide to BDC, mm 12 Progress in the slide, mm 400 The frequency of continuous strokes, min-1 16 The highest frequency of single strokes, min-1 12 Closed height mm 870 Adjusting the closed height 220 mm Size slider, mm left to right 1600 front to back 1600 Dimensions plate, mm left to right 1600 front to back 1600 Power of main drive, kW 110 Dimensions, mm left to right 4670 aft 4670 height above floor level 8110 W 154 000kg

M. No.: 2067 Working width max. (mm): 800

pressure: 30 t stroke: 170 mm column daylight: 600 mm Frame Width: 200 mm distance spindle /table: max. 700 mm weight of the machine ca.: 200 kg Domestic equipments: - Stable welded construction - manually via hand lever - Pressure gauge via pressure gauge - CE mark The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 180 t stroke: 400 mm column daylight: 1500 mm Frame Width: 550 mm distance spindle /table: max. 1000 mm total power requirement: 7,5 kW weight of the machine ca.: 2100 kg dimensions of the machine ca.: 2300x1200x2850 mm Domestic equipments: - Stable welded construction - Pressure cylinder laterally adjustable - Electric control via lever / manual over hand lever - Pressure gauge via pressure gauge - Material supports per cylinder in the height adjustable - CE mark The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press-fit device for ceramic pins in rotor shafts Principle: The ceramic pins are fed to a test station via a pneumatic hose by means of a vibrating conveying bowl, where the position of any single-sided bore is checked. This is done with an optical sensor. Wrongly positioned parts are conveyed through a pneumatic slide into a collection container. Pins that are correctly positioned are fed through another pneumatic hose to the separator of the press-fit tool. The actual press-fit process is also carried out pneumatically with a roller bearing guided punch. First, a manually adjustable pressure p1 is used to check that the pin is not pressed too easily into the shaft. With a pressure p2, which can also be adjusted manually, the pin is then pressed into the rotor shaft at full stop. A 5,000 N preloaded disc spring package prevents excessive force from being exerted on  ...

Inv. číslo: 4465 Type: PL-140 LC Výrobce: OMC Vyrobeno: 2014 Parametry: Příkon: 75 kW

Stainless steel platform movable for bread roll presses / dough dividing machines suitable for all common bread roll presses Solid construction loadable with 1 t Easy locking Stainless steel for optimal cleaning Dimensions: 735 x 640 x 170 mm, WxDxH NEW More TOP bakery machines and equipment in stock!

SPECIFICATIONS: Pneumatic Upholstered Furniture Press

• Single rotary press with 47 punch stations • Tool type EU 19 with BBS dies (die diam. 22 mm) • Unkeyed turret • Output 28,200 - 282,000 sheets/hour • Pressing force max. 80 kN, pre-pressing force max. 20 kN • Tablet-diam. max. 13 mm • Tablet height max. 8.5 mm • Filling depth max. 18 mm depending on filling curve (filling curve 10 mm fitted) • Filling hopper with flange for docking Bohle container MCG500/900 for powder feeding • Agitator blade filling shoe (Fill-o-matic) for fine powder materials (1 spare filling shoe available) • Fast diverter for missing tablets • Korsch PHK2i Plus press force control system • Touch screen Siemens, software operating system Windows CE • PLC Siemens S7-400 • Existing tool set 2x 47 pieces for tablet-diam. 9 mm, flat/flat with facet • Drive 400V/50Hz • New cabling between control cabinet and machine (will be done after  ...

High-pressure radial fan, dust extraction fan, exhaust gas extraction, welding fume extraction, extraction, fan, pressure blower, vacuum blower -Engine power: 0.37 kW -Performance data: not available -Connection input: Ø 65 mm -Connection output: Ø 60 mm -Dimensions: 510/480/H470 mm -Weight: 49 kg

FRITZ MÜLLER ZE 625-4 hydraulic press was built in Germany by Fritz Müller GmbH & Co. KG. The machine has been continuously maintained and upgraded throughout its service life. The first major overhaul was carried out in 1988 by the manufacturer’s service Machinenfabrik Mueller-Weingarten AG. A second overhaul was carried out in 2020, during which the press was brought up to current safety requirements. As part of this overhaul, a new control system based on a SIEMENS SIMATIC S7 PLC controller and a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel was installed, the entire electrical system was replaced, seals were replaced and light curtains were installed. The FRITZ MULLER ZE 625-4 is an extremely versatile press designed for even the most demanding metal forming operations. It is capable of performing operations such as deep drawing, stamping, forging, straightening large w ...

Offer 20202 Specifications: - max. pressing force 35 t - Projection to the middle of the ram 240 mm - Working height adjustable with hand crank 540 to 940 mm - 2 Hand control - Protective shield enclosure with light barrier - Material - Slide-in device - Pneumatic connection - Press control via SIEMENS SIMATEC OP 7 - Drive 400 V / 15.5 kW - Space requirement approx. W 1200 x H 2000 x D 2400 mm - Weight approx. 2500 kg

ARISA S-2-630-240-120-LD mechanical press was built in 2005 in Spain by Arisa S.A. (now Nidec Press & Automation Co. (NP&A)). The machine on offer is an excellent choice for series production of components used in the broadly defined automotive or machinery industry. It enables even the most demanding metal forming operations, such as precise punching and stamping of metal parts. In addition to its standard purpose, depending on the tooling and material feed systems used, the machine can also be used as a transfer press or progressive press. All machining processes are performed with a high press force of 630 tonnes. The drive system, in the form of a flywheel and an eccentric gear, cooperating with two connecting rods, ensures even torque transmission and smooth control of the slider movement. The slider, on the other hand, is guided at eight points using roller guides, which increas ...