press for a used for sale

2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.

-Max pressure at the end of stroke – 4000 ton -Press stroke – 400 mm -Number of stroke – 50 per minute -Max distance of stroke from the table – 1400 mm -Dimensions of slider: 1320 x 1320 mm -Bed dimensions: 1120 x 1600 mm -Bed movement by height – 20 mm -Max pressure of upper ejector – 20 t -Max stroke of upper ejector – 65 mm -Max pressure of lower ejector – 40t -Max stroke of lower ejector – 80 mm -Main motor power – 225 kW -Main motor speed – 730 rpm -Total width — 6280 mm -Total depth – 4885 mm -Total height – 8870 mm -Height over the bed – 7315 mm -Total net weight – 280 092 kg

Qty. 1 Second-hand crank hot forging press – dismantled & in storage Mfc.: Hyunjin Industry, Korea Built: 2008 Status: dismantled and in storage Force: 2500 T Total weight of the machinery: approx. 250 T

Maker: SUMITOMO HEAVY INDUSTRIES (made in Japan) Model: FPA-3000 Year: 1985 (2) Capacity & main specification 1) Capacity: 3000tf 2) Ability Limit Point: 5mm 3) Allowable eccentric load: 3000tf 4) Allowable eccentric distance: L&R 350mm 5) Slide stroke: 350mm 6) Slide stroke speed: 20~50spm 7) Stroke number: 20tpm(Max) 8) Shut height: 1200mm 9) Slide adjust distance: 10mm 10) Bed hard plate dimensions: RL 1300mm x FB 1500mm 11) Slide dimensions: RL 1200mm x FB 1400mm 12) Slide knockout capacity: Total 20tf (pin number: 4ea) 13) SKO stroke: 50mm ( adjust up) 40mm ( adjust down) 14) Bottom knockout capacity: 50tf (pin number 4ea) 15) BKO stroke: 20~30mm 16) Upright internal dimensions: RL 1400mm 17) Main motor: DC 200kw x 1450rpm 440V 18) Floor height: 6800mm 19) Working height: 1030mm 20) Side opening: FB 1000mm x TB 1400mm 21) Flywheel energy: 200tf-m (50spm)  ...

Press form Box 600400280 (meat) Wear 10-15% along the lines of closure there is a small flash

Press mould Box 600400200 (vegetable), wear 70%, part of the perforation and the closure line is filled with material.

Press form Container 20 ml used in the medical industry, wear 10%

Press form Vial FP-50 round, minimum wear - 5%, used in the medical industry

Press form Bottle 25 ml (bottle used in the medical industry)

Press form Bottle 100 mm, D=20 mm round, used in the medical industry, wear 10%

Press form Bottle FP-50 flat, used in the medical industry, Wear 5%, 5-cavity mold

Press mould Ring of control of the first opening of 28 mm. (Turkey) widely used in the medical industry. Wear 40%

Press mould Cap for injections 40 mm Turkey widely used in the medical industry.

Max. capacity 1000 tons Slide stroke 240 mm Shut-height (max.) 650 mm Wedge adjustment 10 mm Number of slide strokes 100 rp

pressure: 1645 t stroke: 1000 mm dayligth: 3000 mm Control: down speed: 280 mm/sec return speed: 275/346 mm/sec distance between columns: 2520 mm total power requirement: kW weight of the machine ca.: t the machine is in very good condition machine was overhauled new control optional you can buy a shifting table as well optional you can buy a surrogate column as well The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Capacity: 0 t Stroke: 0 mm Length of sleeve maximum: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Pressure: 5 to Execution supports Table length: 150 mm Table width: 120 mm Fixed stroke: 30 mm Distance from table to slide: min.: 25 mm max: 145 mm Machine´s weight about: 51 kg Overall dimensions machine: Length: 350 mm Width: 250 mm Height: 550 mm

Capacity: 80 t Stroke: 250 mm Diameter ram: 0 mm Bed length: 0 mm Bed width: 1040 mm Make EMCO F B 5 Type FB 5 Year 1998 Universal milling machine active digital Table length (mm) L = 800 Table width (mm)W = 400 Longitudinal X (mm) X = 600 Cross Y (mm)Y = 400 Vertical Z (mm) Z = 400 Sk40/3150/7.5 Swivable head 90 Gr. Feeds all directions  

Embossing machine, hand-operated hot stamping machine HORST SITTE Heißprägetechnik Dresden P01 pressing force: 5 kN operating height: max. 14 mm Embossing plate: 100 x 60 mm two work tables: 100 x 60 mm, 100 x 40 mm Automatic film feeder Film width: max. 60 mm Power consumption: 200 VA Operating voltage: 220 V 1AC with temperature control unit and mechanical counter ( counter out of order ) used, tested ! with accessories ! Dimensions( transport box ): 360 x 360 x 270 mm

no. of strokes:150 /min impact energy:420 kJ distance lower die block / ram gudeway:435 mm Throat:425 mm steel forging - rectangular up to:110 mm steel forging - diameter up to:125 mm power requirement:22,0 kW weight of hammer:3,9 t weight of anvil:3,0 t ram hammer weight:200 kg weight:6,9 t dimensions (WxDxH):1,1 x 2,3 x 2,4 m

Pressing force: 130t, max. wire diameter: 17mm, cutting length: 150mm, ejector stroke matrix: 125mm, ejector stroke stamp: 58mm. WZ dimensions length/diameter: blade: 80mm/50mm, die: 180mm/90mm, punch: 195mm/75mm. Weight without housing: 27t. Available from 26.08.2024.

nominal force:2500 t stroke:600 mm cycle time:13 - 18 s distance between columns:1720 mm Distance table/ram, max. stroke up, adjustment up:2600 mm table surface area:1720 x 1800 mm allowed max. force:4000 t blow die to die:5000 t ram surface:2100 x 1320 mm capacity of ejector in table:40 t ejector stroke in table:250 mm ejector surface area in table:900 x 820 mm capacity of ejector in ram:6 t ejector stroke in ram:40 mm spindle diameter:425 mm power requirement:900,0 kW weight:335,0 t Dimensions (WxDxH):3,4 x 4,6 x 9,7 m height over floor:8,3 m fully-automated forging line:to produce axle shaft

impact energy:207951 mkg ram hammer stroke:660 mm no. of strokes:100 /min impact energy:2040 kJ distance lower die block / ram gudeway:660 mm Throat:750 mm steel forging - rectangular up to:240 mm steel forging - diameter up to:270 mm power requirement:75,0 kW weight of hammer:16,5 t weight of anvil:15,5 t ram hammer weight:750 kg weight:32,0 t dimensions (WxDxH):3,2 x 1,45 x 3,45 m Mode of operation:pneumatisch

Forklift arms for robots Brand new manufactured

Anchor rods DW 15, DW 20 and DW 26.5mm, different Lengths Anchor rods DW15, buttoned (30cm + 10cm approx. 15) 3,30€/piece 102 Anchor rods DW15, version shaft anchor, 3,30€/piece Hexnuts and full plates 26.5mm

Formwork accessories, uses:: anchor nuts DW15, largely EUR5,90 / piece anchor nuts DW15, small EUR2,90 / piece other dimensions (DW20, DW26,5) on inquiry

Thermal CTP VLF AGFA AGFA Avalon VLF 70 xxt Elite year 2007 with AGFA Printdrive Price: on request

2 Thermal VLF Systems: 1 x AGFA Avalon VLF A xxt year : 2006 5000 paltes with new Laserhead AGFA VLF Platemanager with AGFA Elantrix 150 Onlineprocessorwit transit table to the oven. with Haase oven OG15FU with transit table to gum unit withGum unit RSH with explanation table Price: on request 1x AGFA Avalon VLF A xxt year : 2006 Price: on request

Product dimensions: 650-1200x300x240mm, roll width: 800mm, roll diameter: 350mm, max. speed: 50 cycle/min, length: 5170mm, width: 1452mm, height: 1435mm, weight: 1.1t, one band is torn and needs replacing.

incl. Auto Plate Loader (1 segment), automatic plate feeding from the pallet, maximum plate format 1296 x 2083 mm, maintenance contract, in good condition, with online processor on request available at short notice, Price on request

CONTROLS   PLC SIEMENS S7 FEEDSTOCK TUBE   external diameter min.: 40 mm   external diameter max.: 150 mm   length min.: 260 mm   lenght max.: 1500 mm ELECTRICAL SPECIFICATIONS   total power consumption: 155 kW   mains power supply: 280 kVA   mains voltage: 400 V   mains frequency: 50 Hz System consists of:+ FELSS AYIMUS H02-4NC precision axial forming machine, year 2007+ SONTEC PR 2290 shaft testing machine, year 2007+ BACHMANN BFH 4400 automatic palletizer, year 2007 Exclusions from supply (even if visible on photos)- without chip breaker - without laser marking system

Sheet metal profiling line was built in 2017. Equipment: – profiling machine – guillotine – control system – hydraulic press with an aggregate

Description: Manufactured: 2005 Serial number: 1226 Operating hours: 5.745.000 cycles Material: PS, PVC, PET, PP, EPS Stations: Forming, Cutting and Stacking Forming Area: 770 x 650 mm Maximum Film width: 820 mm Maximum forming depth: 120 mm Maximum dry cycle speed: 30 cycles/min Max.Closing Force of the Cutting Press: 60 ton Maximum Pressure: 6 bar Vacuum pump motor power: 2,2 kW Total heating power of the upper oven: 36 kW Total heating power of the lower oven: 33 kW Vacuum pump capacity: 100 m^3/h Dimensions (L x W x H): 10,0 x 2,4 x 2,7 m Total Weight: 8000 kg Approx. Onsite Dimension. (l x w x h): 12,000 x 2,000 x 2,600 mm, weight approx.: 8,000 kg

Pouch Form Fill & Sealingmachine manufacturer: Nagema, Germany Typ: HS1 capacity: max. 50 bags/min, infinitely adjustable closing: sealing dosage: volumetric doser like rice, candies, spicery etc. bag width: 120 mm bag length: from 50 200 mm adjustable dimension: 2,0 x 1,1 x 2,1 m weight: 900 kg Techn. State: used, very good state

Year 1996, CE norm, complete instructions, control Delem, machine in TOP condition with warranty, more details on request

Description Precise forming with quick tool changes. Our axial t form forming machines of type REB are specially suited with forming forces up to 1,300 kN and effortlessly master complex geometries. With up to six forming stages in combination with an intermediate clamping unit, they meet almost all requirements. The operation is simple and intuitive via touch panel. A sequence control makes every single movement of the respective forming stage user-friendly and individually freely programmable. Optionally, we equip our systems with electrical or hydraulic-numerical drives. For very short cycle times, these forming processes can be carried out step by step in transfer plants. The systems enable intuitive flow-based programming. Simultaneous axis movements ensure fast production processes and enable efficient and highly dynamic production. Technical data REB 660 6-60 mm . . .

Forklift attachment crane booms with hacking little used Producer: Seith conveying new village Type: 60.30/578 Load capacity: 5to LSP: 500 mm fixed boom and column Hacking adjustment by hand with adjust positions Weight: 240 kg ESP: 400 mm Gr. projection: approx. 1.6 m Overall length: 1.8 m, height: 1.4 m Clip on version on the stacker plate and clamp-on PROVIDER Machinery die GmbH 94094 Rotthalmünster, Germany registered since 2010 151 listings online & #57620;. REQUEST SEND Ladies and gentlemen, Please send us a quote for forklift attachment crane booms Salim conveyor Neuendorf crane boom 5 to type: to 60.30/578. Thank you very much and greetings I'm dealer quotes for similar machines interested in financing through leasing or hire-purchase

With cup forming station for 15 cups Cup format: 33 mm x 51 mm, height variable depending on the weight Cutting dimension 41 x 59 mm with pull tab Volumetric dosing unit with 15 measuring points for 10 to 30 grams, weight adjustable. Product hopper approx. 50 litres Performance: max. 30000 cups/h depending on the product consistency is suitable for the filling of honey, butter, jam, etc. With carton packer Hassia. Used, complete overhauled.

With tool for 6 cups. Cup sizes: round 45 mm, height variable depending on weight requirements. Die size: round 53 mm, with pull tab. Dosage: volumetric, 6-cups, 10 to 20 g, weight adjustable. Product hopper approx. 50 litres. Capacity: 9,000 cups per hour depending on the consistency of the product.

automatic meat ball and fishball forming machine, beef balls, pork balls, fish balls, squid balls, 400-600kgs hour, 18-35mm diameter, stainless mobile frame, 3Ph

Punching nibbling machine

Line for forming cevapcici and cevapi (grinder with mixer, portioning device and belt transporter)

2 Thermal VLF Systems form one place: 1. CTP machine Lotem XL 60/80 Creo, YOC 2001 similar to Creo Kodak Trendsetter VLF format 150cm x 200cm in production The imagesetter is equipped as follows: imagesetter, plate machine, plate stacker max.format 152.4 x 203.2, 0.3-0.4 thickness the smallest format is 45.7 x 38.1 The software is equipped as follows: 1 x Lotem XL 60/80 Brisque 4 Impose 1 x Solder 800V transformer 1 x Brisque Back & Front 1 x Lotem XL Singel cassette 1 x Brisque to Improof 1 x Brisque export PS b/w option 1 x EV 800 LVD w/ 8x36GB 1 x Solder XL Wide Conveyor 2. CTP machine Lotem XL 60/80 Creo, YOC 2000 similar to Creo Kodak Trendsetter VLF format 150cm x 200cm in production The imagesetter is equipped as follows: imagesetter, plate machine, plate stacker max.format 152.4 x 203.2, 0.3-0.4 thickness, the smallest format i ...

- Hand & foot control - integrated ambos - solid substructure Specifications: - Hammer weight: 40 kg - Lifting height: 230 mm - Projection: 240 mm - Cylinder Ø: 140 mm - Motor power: 4 kW - Voltage: 400 V - Dimensions WxHxD: 700 x 1900 x 1200 mm - Weight: approx. 900 kg

Combination machine Manufacturer Mubea Type KBL100 5-fold combined Flat steel shears 150x19mm Profile steel shears e.B angle iron 160x7mm or 100x12mm Bar steel shear 70mm round Hole punching Jack 16mm All information to the best of our knowledge, but without guarantee!

1250 x 2500mm TLF 2000w Laser STOPA Sheet storage, SheetMaster, ToolMaster, SortMaster Year: 2005

Electric forklift make KÖTTGEN type ESK 1000 / 2SGSMachine -No: 43602, built in 1987/92Load capacity: 1000 kgStroke: 5200 mmwith battery: DETA 4 Pz S 400 80 Vand charger: DETA D 80 v 60 Aused in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Tiller-guided electro-hydr. Tool lift Fabr. BAKA type EGV 60/605Masch. -No: SOE 27555 built in 1998 with drive Load capacity: 700 kgTable size: 1400 x 600 mmretracted height: 800 mmextended height: 1100 mmStroke: 300 mmBattery power: 24 VDead weight: 400 kgOutside dimensions approx: 1900 x 600 x 1100 mmWith- Battery 24Velec. Travel drive- Emergency stop switchvery little used, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Electric forklift make STILL type EFG 12Machine -No: 09261065, built in 1972Payload: 1200 kgMax. Lifting height: 4000 mmFork length: 1400 mmNet weight: 2410 kgpermissible total weight: 4.0 tHeight with retracted mast: 2150 mmWidth: 1000 mmWith- Battery 24V / 700 AKxa0xa0 12 cells / 605 kg, year 4/90- Duplex mast- chargerdespite the year of construction in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools