pre shredder used for sale

Hello, We hereby offer you a used baler from the manufacturer Presto GmbH & Co. KG, type HPK 50 B. The following technical data have been taken from the manufacturer's operating instructions and brochures, for which we cannot assume any liability for accuracy and completeness. Manufacturer: Presto GmbH & Co. KG Type HPK 50 B Year of manufacture 2005 Hours 15606 Hours Press force main press 50 t Drive power 30 kW Total connected load 31.5 kW Rated current 64 A Throughput under operating conditions at a bulk density of 60 kg/cbm approx. 6.7 t/hour Machine weight press 12.5 t Note: The machine has been repaired in our workshop (main control valve on the hydraulic block replaced) and tested on the fly, in manual and automatic mode. The machine documentation is available in German. A tour of the press is possible by appointment in our workshop. We would be happy if  ...

Hydropneumatic mode of operation Profile height: 180 mm under hold-down Max. Punch Height: 145 mm Wither height: 150 mm Weight: approx. 400 kg

Hydropneumatic mode of operation Profile height: 180 mm under hold-down Max. Punch Height: 145 mm Wither height: 150 mm Weight: approx. 400 kg

Hydropneumatic mode of operation Profile height: 210 mm under hold-down Max. punching height with 2-way adjustable punching heads: 145 mm Wither height: 150 mm Weight: approx. 400 kg

Dixi 50 S ? Vertical Baler Year: 2004 General: Type: Vertical baler for paper, cardboard, foil, PET, textiles, and other recyclable materials Pressing force: 50 t Drive: 7.5 kW electric motor, 400 V / 50 Hz Control: Microprocessor-controlled with programmable settings Bale Performance: Cycle time: ~41 seconds Press time: ~23 seconds Bale size (L × W × H): 120 × 80 × 80?110 cm Bale weight: 350?500 kg (depending on material) Feeding opening: 1200 × 670 mm Dimensions &, Weight: Machine size (L × W × H): 1600 × 1300 × 3100 mm Transport height (lowered): 2240 mm Approximate weight: 2,050?2,180 kg Operation &, Features: Manual bale strapping Automatic start when feed door closes Hydraulic ram return and full bale ejection Adjustable press time and bale size Optional extras: dust-extraction connection, hydraulic door opener Type: Vertical baler for paper, cardboard, foil, PET, te ...

PRESS FORCES   total force (nominal): 100 to PRESS TABLE   table surface (left-right): 950 mm   table surface (front-back): 660 mm   thickness of bolster plate: 68 mm SLIDE   table surface (left-right): 540 mm   table surface (front-back): 450 mm   spigot hole diameter: 60 mm   stroke: 130 mm   stroke rate (max.): 65 /min SLIDE (MECHAN. PRESS)   slide adjustment: 100 mm TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 370 mm DIMENSIONS / WEIGHTS   total weight approx.: 7000 kg Located in Barcelona - Spain 2 identical units available

Neerwaartse persbeweging met zijdelingse belasting - maximale openingsafstand: 400 mm - slag: 400 mm - Tafelafmetingen: 3500 x 3000 mm - De bovenste tafel kan verwarmd worden - De onderste tafel is niet verwarmd - 12 zuigers (diameter 90 mm)

Manufacturer: Italpresse Model: PRE46 - 3 14-6X180 Year of Manufacture: 2007 Voltage: 400V Frequency: 50 Hz Hydraulic Oil: AGIP OSO 46 Heating System Oil: AGIP ALARIA 3 Certification: CE Find more here - .ucymachines/ Contact us at - sales@ucymachines

Key data: 4 t

C-frame press for clinch technology Pressing force 4.8 tons. Air pressure 6 bar, 32 mm total stroke 3 mm power stroke, no tools available

Key data: 15 t

C-Press – 15 T – 300 × 300 mm For sale is a C-press from the manufacturer DURENDUS with a maximum pressing force of 15 t. The machine has a table size of 300 × 300 mm, a maximum installation height of 350 mm and a stroke of 250 mm, making it suitable for press-fit work, assembly processes and small series production in industrial use. Technical data + information: General information - Type: C-frame / single-column press - Manufacturer: DURENDUS - Press force: 15 T - Table size: 300 × 300 mm - Plunger plate: 300 × 300 mm - Max. installation height: 350 mm - Working height: 800 mm - Total height: approx. 2,000 mm - Total width with control cabinet: approx. 900 mm - Total depth: approx. 1,300 mm - Total weight: approx. 1,100 kg - Plunger plate guide: 2-fold Hydraulic cylinders - Stroke: 0–250 mm - Working pressure: 250 bar - Start-up speed: 17 mm/s  ...

CHEAP EQUIPMENT, rock botton prices for owners retirement, send your enquiry for photos, consult PDF file for clear vision, availability: imediate

Bespoke built Hydraulic press for the manufacture of airplane seat back Force: 100 ton Table size 2000mm x 2000mm Platens drilled for oil heating Run out table Omron PLC Cylinder in need for repair, oil heater not included

BLS Lamination Press has been rebuilt to meet your lamination needs. Specifications: Tonnage: 20 Ton Max Temperature: 150°C Electric Heated Platen Table Size: 600 mm x 600 mm Daylight: 425 mm Open/Closing Speed: 10 mm/s Omron PLC HPU

Drive: TOX power package S 04.00.300.44D, pneumatic connection: G 3/8 inch, compressed air preparation: filtered and dried compressed air, max. particle size: 40µm, control: STE 336-306-1/2, max. press force at 10bar air pressure: 40kN, air pressure: 3 to 10bar, total stroke: 300mm, force stroke: 40mm, ambient temperature: 10 to 60°C, length: 1753mm, width: 1100mm, weight of the yoke: approx. 1290kg, with documentation. The machine has been shut down for years, but is in good condition, an inspection on site is possible.

This Hüttenhölscher Body Press was manufactured in 2000. Ideal for efficient carcase pressing applications, it represents a reliable choice for your production needs. Contact us for more information.

Pressing force: 185kN, filling opening dimensions: 1195x541mm, max. bale weight depending on material: 200kg, max. bale dimensions: 1200x780x700mm, throughput capacity: 2 to 5 bales/h, idle cycle time: 35s, strapping: 4 fold with polyester strap, pressing capacity at idle: 68m³/h, pressing chamber dimensions: 1200x780x1300mm, voltage: 3x 400V, motor power: 3kW, length: 1700mm, width: 1046mm, height: 2370mm, weight: 994kg. An on site inspection is possible.

This full electric drive SAFAN E-Brake Premium 80-2550 was manufactured in 2019. It features a pressing force of 80 tons and a bending length of 2550 mm, ensuring robust performance for various applications. The machine is equipped with a maximum stroke of 300 mm and a backgauge with 4 fingers for enhanced precision. If you are looking to get high-quality bending capabilities, consider the SAFAN E-Brake Premium 80-2550 press brake we have for sale. Contact us for further details.

1 Piece Used Automatic Baler Manufacturer: PRESONA Type: LP 80 VH1 Year of Make: 1993 Technical data: Press force: 78 t Specific pressing force: 9.5 kg/cm² Drive power: 1 x 55 kW Throughput capacity: approx. 400 m³/h Filling opening: 1,500 x 1,100 mm Channel format: 750 x 1,100 mm (H x W) Bale weights: up to approx. 450-600 kg Binding: 5-fold vertical Oil tank: approx. 1,000 litres capacity, standing separately next to the machine Machine weight: approx. 22 t

1 Piece Used Automatic Baler Manufacturer: PRESONA Type: LP 80 CH2 Year of Make: 1993 Technical data: Press force: 78 t Specific pressing force: 9.5 kg/cm² Drive power: 2 x 45 kW Throughput capacity: approx. 560 m³/h Filling opening: 1,650 x 1,100 mm Channel format: 750 x 1,100 mm (H x W) Bale weights: up to approx. 450-600 kg Binding: 5-fold vertical Oil tank: approx. 2,000 litres capacity, standing separately next to the machine Machine weight: approx. 30 t

For sale is a high-quality complete system for professional T-shirt direct printing, consisting of an Epson SureColor F2000 T-shirt printer and a Schulze Pretreatmaker. Ideal for textile printing business, start-ups or to expand existing productions. Details of the Epson SureColor F2000 • Direct-to-textile (DTG) printer for professional results • Never used – in very good condition • New printhead worth €2,500 is included (not yet installed) • High print quality and reliable Epson technology Schulze Pretreatmaker • Professional device for pre-treatment of textiles • Top condition • Uniform application for optimal printing results New price of the entire system: approx. 20,000 € Sale & pick-up in Kempten. Pick-up only, viewing possible by arrangement. If you are interested or have any questions, please contact us. Private sale, no return. ...

WE ARE SELLING A PRESSTATION WITH A SNECK SYSTEM WITH/WITHOUT ONE CAPACITY, SUITABLE FOR PRESSING RECYCLED RAW MATERIALS! MANUFACTURER - PRESTO GmbH (Germany) Type: SPN15 Year of Manufacture - 2006 CAPACITY - 30 m³ Power - 11 kW Can be sold unpainted or new painted. PRICE ON REQUEST!

Baler Presona LP 85 VH2, built in 2018, including spare parts package Technical data: Manufacturer: Presona Sweden Type LP 85 VH2 Year of manufacture 2018 Drive power 2 x 45 kW Operating hours 40,350 Effective operating hours approx. 22,000 Press force pre-press 28 t Press force main press 85 t Insertion shaft 1500 x 1100 mm Bale dimensions 750 x 1100 mm Bale weight 450 - 650 kg Theoretical volume: 1200 cbm/h Throughput at 30-100 kg/cbm: 13-30 t/h Bonding 5-fold vertical, (3-fold horizontal) Oil tank capacity 2000 L Transport dimensions press 10400 x 2400 x 2800 mm (LxWxH) Weight approx. 27000 kg Materials: paper, cardboard, PET bottles, films, light waste. Note: The press is in good condition. It was dismantled from ongoing operations. The following work was carried out by us: New wear plates in the press channel Gasket completely replaced on the master cyl ...

Channel baler Presto HPK 20/50 S, built in 2007 Manufacturer: Presto Type: HPK 20/50 S Year of Make: 2007 Operating hours: 10490 (as of 08/2026) Drive: 22 KW Press force: 50 t Filling opening: 1200 x 700 mm (LxW) Channel cross-section: 700 x 750 mm Filling volume, max. 0.63 m³ Cycle time: 23 s Binding: 3-fold, automatic throughput at 35 kg/cbm: 2.9 t/h 60 kg/cbm: 4.3 t/h 100 kg/cbm: 6.3 t/h Bale weight: up to 450 kg Machine dimensions: 760 x 1350 x 2350 mm (LxWxH) Machine weight: approx. 7,500 kg Materials: paper, cardboard, foil Note: The press is in good condition and is currently still in operation. A visit is possible by arrangement. The machine will be available from the end of 2026. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to ...

Packaging line Ishida / Prewa The packaging line was used for packaging accessories. Available now. The facility consists of: 1 St. Ishida multihead weigher (10 heads), built in 2004 1 St. Ishida multihead weigher (10 heads), built in 2003 1 St. Prewa vertical packaging machine (type 25/40), built in 2005 2 Z-shaped conveyor belts 2 St. vibrating gutters 1 piece of bunker tape

General SKU328Y700 LocationBarneveld MakeExtrella TypeST-EM No.91017 Pressure Working pressure6 Bar Vacuum possiblecheck Number of vertical pressure tanks1 Main Features MaterialGlass Volume4210 Ltr. Pressure6 Bar Specified Features - Pressure vessel Capacity4210 l. Vessel sizesø 1600 x 2200 mm Dished topcheck Dished bottomcheck ManholeDN600 Top connectionscheck OutletDN80 Max. temperature—10 / 200 °C MaterialGlass - Enamel (TPE-2000) General Year of construction1991 Mounted on legscheck Floorspace1,60x1,60 m Total height3,20 m Weight2100 kgPressure vesselsNew arrivalsEstrellaTanks > Pressure vesselsNew arrivalsBrand > Estrella What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. P ...

General SKU328Y701 LocationBarneveld MakeEstrella TypeST-EM No.91016 Pressure Working pressure6 Bar Number of vertical pressure tanks1 Main Features MaterialGlass Volume4210 Ltr. Pressure6 Bar Specified Features - Pressure vessel Capacity4210 l. Vessel sizesø 1600 x 2200 mm Dished topcheck Dished bottomcheck ManholeDN600 Top connectionscheck OutletDN80 Max. temperature—10 / 200 °C MaterialGlass - Enamel (TPE-2000) General Year of construction1991 Mounted on legscheck Floorspace1,60x1,60 m Total height3,20 m Weight2100 kgPressure vesselsNew arrivalsEstrellaTanks > Pressure vesselsNew arrivalsBrand > Estrella What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barn ...

Desta BAS 500-16 Brochure Press Booklet pressing unit/brochure press Age: 2001 Format: 35x50 cm

pressure:400 t distance between columns:1100 mm stroke:250 mm no. of strokes:25 - 75 /min distance table/ram, max. stroke up, adjustment up:900 mm table surface area:1100 x 965 mm capacity of ejector in table:30 t ejector stroke of ejector in table:80 mm capacity of ejector in ram:3 t stroke of ejector in ram:60 / 70 mm ram surface:980 x 800 mm column travel -side:800 mm ram adjustment:20 mm power capacity:80,0 + 5,5 kW weight:47,0 t Dimensions (WxDxH):3,5 x 3,3 x 6,0 m weight of switch cabinet:1,4 t dimensions of electrical cabinet (WxDxH):4,9 x 0,5 x 2,6 m ejector in ram:hydraulic

pressure:400 t distance between columns:1060 mm stroke:450 mm no. of strokes:15 - 30 /min distance table/ram, max. stroke up, adjustment up:1160 mm table surface area:1000 x 700 mm capacity of ejector in table:2 x 16 t ejector stroke of ejector in table:125 mm Die cushion pressure in table:120 t Die cushion stroke in table:2 mm capacity of ejector in ram:2 x 4 t stroke of ejector in ram:100 mm ram surface:1000 x 700 mm column travel -side:630 mm power capacity:55,0 kW weight:50,0 t die cushion in table:2. station

Deltapilot S Endress+Hauser unused / like new Technical Details: Typ: DB50L-AC44BD13EG20 IP66/NEMA4X CONTITE VA 0 - 4000 mbar

Ueberholungsjahr 2016 Baujahr 2010 Saegeblatt Hartmetall 500 mm Antriebsleistung Saegemotor 7,5 KW Drehzahl Saegemotor 2000-38000 min-1 Schnittgeschwindigkeit Saegeblatt 3100-6000 mm/min Saegeblattvorschub stufenlos Einstellbar 0-40 mm/ s Arbeitsbereich 90° max.:460 x 50 mm Nachschublaenge Pneumatisch: Einzelhub:max. 300 mm Servogesteuert: Einzelhub:max. 300 mm Mehrfachhub:max. 9999mm Nachschubgeschw. Servogesteuerte Nachschubeinheit 300 mm/s Druckluftanschluss bauseits 6 bar Gewicht(Saege)ca.: 1000 Kg Abmessungen LxBxH(Saege)ca.: 2100mm x2000mm x1600mm Hydraulikagregat) ca.: 900mm x600mm x800mm Technische Beschreibung Pressta Eisele Profilma 540 Retrofit Pressta Eisele Profilma 540 Retrofit Vollautomatischer Hochleistungs-Saegeautomat fuer NE-Metall und Kunstoffe Die Maschine befindet sich nach abgeschlossenem Retrofit sowohl technisch als auch op ...

Manufacturer: Pressta Eisele Type: 501 angle punch Overhaul year: 2020 Built in 2010 Saw blade carbide: 500 mm Drive power saw motor: 5.5 KW Speed Saw Motor: 2860 min-1 Cutting speed Saw blade: 4500 m/min Saw blade feed: infinitely adjustable 0-70 mm/s Tool area 90 max approx.: 20 x 250 mm Punching cylinder: 1 pcs vertical top diameter 100 mm ,1st st horizontal front diameter 100 mm Punching force power: 4.0 KW Pressure max. 280 bar Pressure in KN at 280 bar approx.: 210 KN Volume flow at 280 bar approx.: 6.8 L/ min Pressure in KN at 200 bar approx.: 150 KN Volume flow at 200 bar approx.: 9.5 L/ min Supply length pneumatic: single stroke max. 600 mm Servo controlled: single stroke max. 600 mm Multiple stroke max. 9999mm Replenishment. servo-controlled replenishment unit max. 500 mm/s Compressed air connection on the side: 6 bar Weight (s ...

Surface grinding machine. Magnetic chuck of 550x250mm. Table travel: 700mm. Grind surface area: 600x350mm. Max. height: 375mm. Cross travel: 300mm. Wheel: 350x127x50 / 300x127x100 Weight: 2900Kg.

Palletizer Kettner Manufacturer: Kettner Type: Press uni KEG EP - BP Year of construction: 1995

Premixer SIMONAZZI with Brix and CO2 controlControl Siemens S7Power 18,000 l/h

PRECAST LINE VOLLERT FILIGREE AND DOUBLE WALL LINE precast Filigree and double wall production

Planetary grinders Manufacturer Precise In a suitcase with extensive zubehoer Rule transformer Tool holder SK40 with interchangeable tightening bolt Control range: 15000 - 45000 rpm Orbital speed 70 - 120 rpm when working horizontally max.: 70 rpm Radial delivery: 0.0001 - 0.002 mm Reception: SK40 electr. Connection: 220 V, 600 W Special price

High-frequency Fraesspindel Precise Type PKZ 50/51 with SK40 for mounting in the spindle of a milling machine and collet holder for receiving the cutter. Speed range 15,000-60,000 rpm Manufacturer Precise Control unit PVSF1 Waerme exchanger PWK17-8 Spindle PK 50/51 without automatic Tool. fully operational Special price! More information on request

Electric tool changer RASTER Premat EWD20

Press-Vite Buegel / Steam table 4 whirlpool hoods, 9000W Bj .2002, Pr12LP+ You buy a bell system Press Vite Buegel- / Steam table,with 4 hoe-adjustable whirlpool hoods, and 2 steam generators /en working width approx. 340 cm, 380VPr12LP - 9000W Bj 23.10.2002 Control GE VAT20 U20NOK7S BJ. 16.02.2002 Article number 17746; Please include requests;

Set for KUKA robot working area limitation Manufacturer: Nabtesco precision Europe Type: RV-260F-58.62 All information without guarantee

Technical data: -Saw blade size 300 mm -Blade rotation speed 2800 RPM -Section - 90 ° 160 x 20 mm 100 x 80 mm -at 45 ° 100 x 40 mm -Adjustable miter vise -Drive 380 V / 1,5 kW - space requirement approx. B H 400 x 1400 X 700 mm -Weight approx. 80 kg -with:-vert. -Vice - machine stand -Feed roller 2000 mm -Evacuation roller conveyor with MaÃ? attack with analog display via Handwheel movable 3100 mm