pre heater used for sale

3 Double Feeders, 1 Hand Feeder, 1 Cover Feeder 1522, Stiching Unit 1528, Three Knife Trimmer, Belt Delivery, Format: Max. 365x305mm, Min. 148x105mm, Max. 360x300mm, Min. 140x75mm, Stiching Thickness: Max. 10mm, Capacity: 9000 Cycles/Hour, Standard Accessories

Press cylinder K260 S210 H8910 for use in scrap baler shears. Piston diameter - 260 mm; rod diameter - 210 mm; stroke - 8,910 mm Operating pressure: head side - 180 bar; Bottom side - 225 bar;

automatic divider The divider RheoPan Precision is the basis of RheoPan line. It is very precise in weight thanks to a system of double weighing of the dough and the automatic adjustment of settings. Its stress-free division system allows it to handle both highly hydrated and fermented doughs, as well as hard doughs. It can thus produce a very wide variety of breads depending on the modules installed.

Key data: 400 mm, 300 mm, 250 mm

Type: Wire EDM Machine Ident Number: 22606 Category: Wire EDM Machines / EDM Manufacturer: Sodick Model: SLC 400 G Premium + Year of construction: 2015 Travel: 400 x 300 x 250 mm [ X x Y x Z ] max. workpiece weight: 500 kg U / V axis: 150 x 150 mm Cutting in a water bath Radiator Working tank 850 x 610 mm Taper +/- 25° at tool height 130 mm Control SPW

Key data: 300 mm

Cutter diameter: 300 mm Max. notching width: 350 mm Max. notching depth: 110 mm Max. profile height: 150 mm Feed length: 500 mm Stop between 20° - 90° - 20° Pneumatic Workpiece Clamps Minimum Quantity Spraying Device Manual feed Weight: approx. 280 kg

Fully automatic hot stamping press Oropress Mechanical eccentric press with lift table Lift table as pneumatic sliding table 250 x 250 mm Fully automatic sequence, optionally triggered with foot switch for single stroke Heated press punch 120 x 200 mm up to 250 °C Safety grille Film Feed Unit Built in 1986

- Used hydraulic power unit complete with control cabinet. - Ready to connect and ready to use. - E.g. for servo hydraulics use. - Litre capacity: 138 L/min. - Nominal pressure: Pmax 280 bar. - Electrical supply: 132 kW / 50 Hz / 400 V. - Incl. comprehensive and maintained components (see pictures). - Aggregate rental possible. - Other power units and hydraulic components available on request (sale/rental).

Stamping pressure : 40 kN Stamping area : 150 x 210 mm Stamping die holding plate : with dove-tail guiding Stroke of plunger : 28 mm Daylight (adjustment of height) : 0-180 mm Throat (middle of stamping plate to bow) : 190 mm Foil feeding system : motor-driven, 1-fold running from the left to the right side with foil re-winding device Working table : sliding automatically in and out with table lock pneumatic, 400 mm x 450 mm PLC : Siemens S 7-1500 with TP 700 color Safety device : in CE-execution with safety light curtains in front Color of the machine : light grey RAL 7035 Voltage: 3 x 400 VAC (L1/L2/L3/N/PE), 50 Hz. Pneumatic access : oil and water free compressed air, 6bar

Offer 24245 Specifications: - Feed of the milling unit pneumatically - Work table adjustable in height via handwheel - Horizontal and vertical material tension - Milling cutter diameter up to 300 mm - Max. profile height 190 mm - Max. milling depth 110 mm - Max. milling length 400 mm - Angle-adjustable stop Li + Re 20 90 20 ° - Milling spindle speed 2800 rpm - Drive 400 V / 2.2 kw - Compressed air connection 6 - 8 bar - Air consumption per work cycle approx. 10 l - ELGO digital display for material cross fence - Pneumatic profile clamping - Spraying device - Space requirement approx. W 1100 x H 1500 x D 700 mm - Weight approx. 300 kg

Key data: 260 mm, 520 mm, 16 U/min

mcm TC 260-105-1500 Premium - Lathe (new) Included premium equipment: - Heidenhain ND5023 3-axis position indicator - 5-position longitudinal stop for the saddle - SRW-Amestra Multifix C quick-change holder with 4 inserts - LED workplace lighting - Set of leveling pads from Spinelli Standard equipment: - Bed, base, headstock, tailstock & sled made of cast iron - Bed guides are induction hardened and ground - Headstock with induction hardened and ground gears - High-precision spindle bearing - Double mechanical coupling - electromagnetic brake - Fast feeds - Pneumatically assisted tailstock movement - Electronic components from Siemens and/or Schneider - Safety devices in accordance with EC standards: plexiglass safety lining guard with microswitch, turret plexiglass safety guard, rear guard along the entire length of the machine, protection of lead screw and feed r ...

Machine Type: Aluminum Saw Manufacturer: Emmegi Type: 550 SCA Year of Make: 1996 Condition: used Offer will only be sent if a complete imprint is provided! Price 2.950 Euro incl. 19% VAT Location Warstein , Germany Reference M-EME-0724 DESCRIPTION We offer you a used aluminum saw from the manufacturer Emmegi. Saw blade stutters up, hence the special price. Saw drive runs clean and quiet Digital angle display New minimum quantity lubrication from Menzel from 2022 Availability: immediately Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions of payment. Errors in the descriptions and offers are reserved!

Machine Type: Door Belt Drilling Machine Manufacturer: Pressta Eisele Type: Multyfor M Year of Make: 1996 Condition: used and functional / main switch toggle defective / coolant bottle missing. Offer will only be sent if a complete imprint is provided! Price 1.250 Euro incl 19% VAT Vb Location Warstein , Germany Reference M-PRE-0724 DESCRIPTION We offer you a used multi-spindle drilling machine from the manufacturer Pressta Eisele. Availability: immediately Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions of payment. Errors in the descriptions and offers are reserved!

Used extendable spiral mixer WP KEMPER, type: President 75 - for 75 kg flour or 120 kg dough - Incl. 1 tank car - 2 Time clocks - Forward gear with 2 speeds -Reverse gear - Condition: Good, been in use until the end Visits and test runs are possible by arrangement.

Lenght 5m Options: Load&unload VIRTUAL AXIS FOR CUTTING UNITS INCLINATION PROFILE CLAMPING LABEL PRINTER

range L-W-H: 960 x 460 x 860 mm weight: 75 kg : 8 St. Tool trolley filled Contents and equipment see pictures The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding length: 600 mm grinding width: 300 mm workpiece height: mm total power requirement: kW weight of the machine ca.: 2,9 t dimensions of the machine ca.: 2,9 x 2,8 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bizhub PRESS C1060 = Equipment No: 1817933817 – Digital Printing Machine Incl. DF-626 Original Feeder, PF-707 Paper Cassettes, SD-506 Finisher, PB-503 Perfect Binder, IC-308 ext. EFI Controller incl. VI-507 Interface kit, RU-509 Connection Unit

bizhub C3350 = Equipment No: 1818829867 – Color MFP Incl. PF-P13 second paper cassette, FK-512 fax module

Precise 0,6kw ESC 3043 +Control Unit 50k 1min. pneum. Tool change D.4mm Total weight 15kg. Only the spindle without cable weighs approx. 3.5kg Pneumatic collet/tool change. Diameter 4.00mm Max. speed 50,000, minimum 10,000 is specified. According to the controls, however, it somehow goes up to 6000 down. Water cooling is necessary during operation, this is all described in the original operating instructions. Water cooling is not included. The requirements are described. There is at least talk of liquid cooling on the technical drawing. Very good used condition, full function. You will receive an invoice in paper form. Differential taxation according to sec. 25a of the German VAT Act. Therefore, no VAT is shown on the invoice. 24 63 87 F1448 (internal article number)

Reference Num.: 4147 Brand: Xerox Type: Versant 180 Press Construction year: 2016 Impressions: 5 mio Available: directly Status: Not in production Location: Deutschland Machine size: Length: 1,212 mm, Width: 760 mm, Height: 831 mm Total weight: kg 295 / lbs 650 Equipment: - Duplexdruck - Finisher - Scanner

Reference Num.: 4148 Brand: Xerox Type: Versant 180 Press Construction year: 2016 Impressions: 4 mio Available: directly Status: Not in production Location: Deutschland Machine size: Length: 1,212 mm, Width: 760 mm, Height: 831 mm Total weight: kg 295 / lbs 650 Equipment: - Duplexdruck - Finisher - Scanner - Fiery

Key data: 550 mm

Five Axis CNC Controlled Dual Head Double Miter Circular Sawing Machine with Loading and Unloading Device Maximum section length with two saw heads at the same time - 6,000 mm Maximum saw blade diameter Ø 550 mm Infinitely programmable mitre angle adjustment - 15° / 90° / + 45° Saw blade drive power 2 x 2.64 kW Dimensions approx. 11.3 m x 2 m x H 2 m (with closed safety doors)

Max. saw blade diameter: 500 mm Cutting area up to 80x 200 mm Feed length: max. 800 mm with digital display Saw blade speed: 2,000 - 3800 rpm Unit counter with automatic shutdown when setpoint is reached Infinitely adjustable pneumatic material feed Hydropneumatic saw feed Pneumatic material tensioners Spraying device Only 2200 operating hours

Transformer, Control Transformer PAUL PRENGEL (PREDÜ) PDT 0.1 ( PDT0.1 ) VE: 400 V Va: 17 V 0.1 kVA New ! Dimensions: 130 x 70 x 140 mm

ESC-HIGH PRESS ´PLUS´ E3 Model 0 max. print size: 510 x 720 mm max. sheet size: 520 x 720 mm min. sheet size: 270 x 350 mm gripper margin: 10 mm Additional equipment: - RKS squeegee system - Antistatic device with control unit AFC-2 and SCPB electrodes 530 with cable length 180 cm including connector HV-4 - integrated cleaning station system TEKNEK in the machine inlet - equipped with ESC leading edge feeder A dryer can also be added /listings/3715380-used-wicket-long-term-dryer Find more here - /

The Xerox iGen 150 Press is a high-performance digital printing press designed for commercial and industrial printing environments. It is known for its productivity, versatility, and print quality, making it a popular choice for print service providers. Key Specifications: - Print Speed: 150 pages per minute (ppm) - Monthly Duty Cycle: Up to 4.8 million pages - Print Resolution: 2400 x 2400 dpi for sharp image quality - Paper Handling: - Max Sheet Size: 364 x 660 mm (14.33" x 26") - Stock Weights: 60 to 350 gsm - Supports coated and uncoated stocks, textured papers, and synthetic materials - Color Management: Integrated with Xerox Automated Color Quality Suite (ACQS) for consistent, accurate color reproduction - Variable Data Printing (VDP): Ideal for personalized marketing materials Features and Benefits: - Productivity: High-speed digital press suitable for large-volume printing wi ...

Measuring machine Premetec measuring machine, year of manufacture: 2016, serial number: 08370, int. number: 109, inventory number: 10-1100715-0, machine weight: 1,100 kg, with Siemens Simatic HMI control, PC control, with feed and discharge belt, conveyor width approx. 600 mm, fencing and gripping device Jvodke, Machine designation: Measuring machine

This Press laminating machine is the perfect solution for automotive, aerospace, and various manufacturing applications. Built before 2015, it offers exceptional precision and durability .Designed to handle large and complex laminating projects efficiently, this machine is ideal for businesses seeking to improve quality and productivity. We have three machines from different years ( two dated before 2015 and one from 2018). Machine details : Dimensions (L x W x H): 3600 mm x 2850 mm x 4530 mm Table Size: 1600 mm x 900 mm Weight: - Overall: 4300 kg - Lower part: 4900 kg - Upper part: 4300 kg Find more here - / Contact us at -

AFS Corona Pre-Treatment system Type (Typ): G 60 M Input (Eingang): - Voltage (V): 400 - Current (A): 16 - Frequency (Hz): 50/60 Output (Ausgang): - Power (W): 6000 Technical Data Roller Width: 2700 mm Electrode Width: 2500 mm Maximum Mechanical Speed: 250 m/min Maximum Generator Power: 6 kW / 1 & 5 Core Operation Electrode Type: Ceramic Electrodes Discharge Roller: Ceramic Roller Drive Type: Driven Discharge Roller Cooling Type: Water-cooled Pre-treatment Direction: Controllable via web path Pressure Rollers: Present on both sides Find more here - / Contact us at -

Saw blade diameter vertical and horizontal: 500 mm Max. profile height: 280 mm Max. latch width: 300 mm Max. notch height: 185 mm Max. notch depth: 185 mm Swivelling material stop with detent points and digital display Latch height motorized adjustable with digital display Motorized adjustment of angles with digital display Hydropneumatic material feed via 2-hand operation Pneumatic material tensioners Coolant lubrication

Manufacturer: Eckverbinder Presse pneumatisch,

Reading type: . 0 weight - pallet system: . kg length: . mm Calipers, depth gauges Calipers Format: 250mm 300mm 1500mm 3000mm, make: Preissner 2000mm Depth gauge: 300mm, make: Format 200mm The technical data are manufacturers or operators specifications and are therefore non-binding for us. We reserve the right to sell items prior to purchase, our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items, accessories for your workshop If you want to sell machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description N ° 1 column for Mir 270: length: 2900 mm diameter: 100 mm conditions: new

Description Peletizer Previero Model TA 400 NO elctrical cabinet 3 kit of used kniwes

Technical specification Conveyor belt width: 1.87 m Length of the vertical part 8.6 m Lifting height: 5.2 m Total length in horizontal view: 26 m Belt depth in the horizontal loading area: 0.55 m Motor power: 7.5 kW + 5.5 kW If you have any questions, please call us: +48 696 072 985

Description Thermoforming with vacuum and pressure Twin heated surface Working surface 1000 x 700 Vacuum pump Adjustable air presure Used to proceed PPSU

Technical specification Conveyor belt width: 1.87 m Length of the vertical part 8.6 m Lifting height: 5.2 m Total length in horizontal view: 26 m Belt depth in the horizontal loading area: 0.55 m Motor power: 7.5 kW + 5.5 kW

Specifications: ✅ Brand: Previero ✅ Model No.: MU-408 ✅ Cutting chamber: 800 x 380 mm ✅ Rotor: Closed, inclined cut, water-cooled ✅ Engine: 75 kW (100 hp) ✅ Ideal for continuous work and high-density materials Common Applications: Shredding of technical plastics, purges, thick sheet, pipe, large parts Integration into recycling or extrusion lines Suitable for materials such as PP, PE, PET, PVC, ABS, PA, among others High production capacity with excellent crushing quality

Description GRANULATOR WITH HOLLOW ROTOR Nr. knives 7 Nr. counter knives 2 Rotor length 1600 Diameter rotor 900 Motor power 200 kW

Manufacturer: Brunotte & Niemeyer Year of Manufacture: 1968 Type of Machine : Hot cure tire press - Open/close system with hydraulic spindle - Plc cabinet - Press on it self can load tyres by own boards - Air max: 16bar pressure inside - Standard working pressure 8 bar - Hydraulic pump - Heating: Steam - Accessories: optional 24R20.5 XS mould Find more here - / Contact us at -

Size: Equipments: with pressing unit Upright stack delivery

FOR SALE – AMADA HFB 125-40 PRESS BRAKE – USED ZOTOFF Company – Used sheet metal equipment We offer for sale an AMADA HFB 125-40 hydraulic press brake, in excellent working order, ideal for precision industrial sheet metal work. ✅ Technical characteristics: Model: AMADA HFB 125-40 Year of Manufacture: 1992 Bending force: 1250 kN Maximum stroke: 180 mm Supply voltage: 380V / 50Hz Installed power: 11 kW Current rating: 24 A Number of phases: 3 Weight: 10,000 kg Serial Number: HFB012540H20610 Robust, reliable machine perfectly suited to mechanical-welding, boilermaking or metal parts workshops. Other sheet metal machines available (equivalent examples): BYSTRONIC Beyeler PR 150T – 150 tons, CNC TRUMPF TrumaBend V85S – 85 tons, numerical control LVD PPEB 135/30 – 135 tons, with Easy-Form control COLLY MTP 125T – 125 Ton Hy ...

Deblister machine Manufacturer: RBP Bauer GmbH Type Press out Model EC

Qty. 1 Second-hand shredder Mfc.: METSO Denmark A/S Model: M&J Eta PreShred 4000S Built: 2013 Condition very good Working hours: 11,347 Power supply: Voltage 400 V AC, 50 Hz Main motor: 2 X 200 kW Rated current 760 A Main motor, full load current 2 x 341 Amp., PLC controller Drive principle, hydrostatic transmission with power consumption limiter. Working cutting cassette: 2 shafts Operating asynchronously Speed: 33 rpm Number of rotary knives: 2 x 12 pieces Number of lower, fixed knives 2 x 24 pieces Bearings 2 x 2 barrel

Koppens 900mm Preduster 900mm belt width With blower Stainless steel, on wheels