power press used for sale

Vertical Multistage High Pressure Centrifugal Pump KSBTyp Movichrom N CN 3/10 2RFabr. Nr 1-P30-837561Nominal flow rate max. 3 m3/hNominal delivery head 70 meters = 7 barNominal speed 2900 rpm. Motor power 1.5 kWNet connection 400 volts, 50 Hz- pump structure in 10 stages- pump elements made of stainless steel, pump base made of cast iron connection flanges DN 32- suitable for drinking water supply, irrigation and drainageSpace requirement pump L x W x H 250 x 220 x 830 mmWeight 38 kgUnused replacement pump made of

Single-column eccentric press AMBOLD type PEEV 25.2Masch. No. 11734 / 02 Year of construction 2002Compressive force 25 ton. Projection 200 mmTable area 520 x 400 mmPlunger area 155 x 155 mmHole in table 185 x 155 mmStroke adjustment 4-80 mmPlunger adjustment 40 mmInstallation height max. 270 (largest stroke in UT, table below)Clamping pin hole 32 mmTable height adjustment approx. 150 mmPlunger strokes 160 strokes/min. Motor power 2.2 kWNet connection 400 volts, 50 Hz pneumatic clutch-brake combination

Double Column - Hydraulic Press RASTER ZEULENRODA (WALTER) Type WUP S 60Masch. No. 136 / 7 (156-165) Year of manufacture 1999Basic machine from 1987, in 1999 Overhauled with new controlPressure capacity 60 ton. Stand width 1090 mmStand passage laterally 265 mm (one-sided) Plunger area 650 x 300 mmAdditional plate on ram 990 x 550 x 60 mmTable area 990 x 550 mmPlunger stroke max. 320 mmInstallation height 330 or 390 mmTable height above floor 980 mmHydraulics Operating pressure 320 barRapid traverse downward 75

A Bruderer differential stroke press (knuckle-joint press) is available. Press force: 3200kN, installation height min./max.: 420mm/520mm, clamping table dimensions X/Y/Z: 1400mm/1000mm/150mm, table height: 1030mm, ram dimensions X/Y: 1000mm/800mm, belt passage width and height: 400mm/450mm, machine dimensions X/Y/Z: approx. 2350mm/1850mm/4550mm. Documentation available. On-site inspection is possible.

Compressive force: 1000kN/100t, ram stroke: 200mm, max. operating pressure: 290bar, control: DNC70, safety distance: 166mm, overtravel time: 104ms, overtravel distance: 7mm.

Pressing force: 440kN, working width: 1600mm, cylinder stroke: 150mm, travel X/R: 400mm/200mm, adjustment speed R-axis: 200mm/s, installation height: 400mm, throat depth: 200mm, machine stand distance: 1530mm, motor power: 7.5kW, weight: approx. 2100kg. Including various accessories and tools. Documentation available. On-site inspection is possible.

An old Künstner & Hampel eccentric press is available. Pressure capacity: 25 tons, power requirement: 2.5 HP. On-site inspection is possible.

A roller press (briquetting press) Köppern Maco is available. Production capacity: 10 MT/h, roller diameter: 720mm, roller width: 315mm, briquetting shapes: bolted segments, motor type: Siemens electric motor, motor power: 190kW, gearbox type: spur gear, machine dimensions X/Y: approx. 5000mm/5000mm, weight: approx. 15000kg, control: Siemens S7-300 Simatic. Including two new segment sets and one installed segment set. Documentation available. On-site inspection is possible.

A Sahinler workshop press is available. Press pressure: 150t, max. pressure: 244bar, working width: 1520mm, piston stroke: 300mm, ram dimensions X/Y: 200mm/1520mm, through hole: 100mm, table dimensions X/Y: 600mm/1520mm, max. installation height: 610mm. Forward speed: 9mm/s, retraction speed: 10mm/s, working speed: 5mm/s, drive power: 11kW. Machine dimensions X/Y/Z: approx. 2500mm/1000mm/2400mm, weight: approx. 3000kg. Documentation available. On-site inspection is possible.

Pressing force: 2000kN, working width: 3100mm, column passage: 3240mm, max. stroke: 400mm, throat depth: 250mm, max. installation height: 965mm, NC axes: 11, hydraulic volume: 550l, machine dimensions X/Y: approx. 4400mm/3400mm, weight: approx. 16600kg, control: Cyb-Tech Infinitron. Documentation available. On-site inspection is possible.

Four Neff single-column presses are available. 1) Neff T 6.3, year of manufacture: 1989, output: 3kW. 2) Neff single-column press, operating hours: 9097h. 3) Neff EP 10 single-column press, year of manufacture: approx. 1950. 4) Neff single-column press. On-site inspection is possible.

Working dimensions X/Y: 3000mm/2000mm, cylinder stroke: 1000mm, height adjustment: 2000mm-2600mm, length adjustment: 3000mm-6000mm, pressing force: 2t, space requirement: 4100mm/1000mm/2450mm, weight: approx. 1500kg. Documentation available. On-site inspection is possible.

FETTE Terminal Data Control Type 2080 Year 1989

Two identically constructed heated Ital presses are available. Press length: 1700mm, press width: 1500mm, press height: 1400mm, press force: 800t, total connection: 30kW, machine dimensions X/Y/Z: approx. 5400mm/2300mm/3200mm. Including piston from above, fittings for chair seats and heating. Documentation available. On-site inspection is possible.

FETTE Data Control 2 Installed in a mobile cabinet including an EPSON printer

A total of five Cannon foam systems are available. Materials: isocyanates and polyol, press plate dimensions X/Y: 720mm/650mm, lid opening angle: 100°, tilt angle: 60°, opening min./max.: 312mm/502mm, parallel stroke: 190mm, approach stroke: 95mm, press stroke: 95mm, ejector stroke: 75mm, control: PLC. Including material preparation. Documentation available. On-site inspection is possible.

COURTOY R292F Compressor Missing the 2 compressed descents and the cables between the electrical cabinet and the machine; All the documentation including the electrical diagrams is present (in French), Punch type: D, Weight (kg): 4500 , Cadence / hour: 43,000 - 350,000, Compression (kN): 100, Precompression (kN): 10, Maximum tablet dimensions (mm): 25,40, Die outer diameter (mm): 38,10, Matrix height (mm): 23,81, Punch diameter (mm): 25,40

Press capacity: 50 ton Ram stroke: 54 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 303 mm Table surface area : 810 x 550 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 7,5 ton Main Motor: 11 kW

A dismantled Mecamaq hydraulic press is available. Pressing force: 100t, max. pressure: 290bar, main piston diameter: 200mm/120mm, auxiliary cylinder diameter: 40mm/25mm. Main cylinder working stroke: 500mm, max. installation height: 800mm, working height: 800mm, effective dimensions X/Y: 700mm/500mm, table dimensions X/Y: 800mm/500mm, working speed: 6mm/s, return speed: 150mm/s. Max. tool dimensions X/Y: 800mm/600mm, max. tool weight: 1000kg. Machine dimensions X/Y/Z: approx. 1000mm/1350mm/2750mm, weight: approx. 4000kg. Documentation available. On-site inspection is possible.

Press capacity: 100 ton Ram stroke: 300 mm Slide adjustment: 125 mm Shut height (stroke down, adjustment up): 600 mm Free frontal opening L-R: 2.020 mm Free lateral opening F-B: 620 mm Table surface area : 2.000 x 1.000 mm Slide area: 2.000 x 900 mm Hole in table: 1.700 x 300 mm Number of strokes: 10 - 50 s.p.m. Table height over floor: 1.200 mm Required power: 39 kW Height over floor approx.: 4.400 mm Dimensions L x W x H: 5.166 x 2.500 x 4.400 mm Weight of machine approx.: 38 ton

Capacity: 60 ton Throat depth: 275 mm Ram stroke: 5 -100 mm Shut height (stroke down, adjustment up): 375 mm Table surface area : 740 x 470 mm Number of strokes: 14 - 100 s.p.m. Required power: 10 kW Dimensions L x W x H: 2.300 x 1.500 x 3.000 mm Weight of machine approx.: 3,5 ton

: ja weight of the machine ca.: 9,5 t serial number: 10457/2 : 160000 KG stroke of worktool slide: 41 Hub/min Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press capacity: 40 ton Ram stroke adjustable: 8 - 50 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 310 mm Free frontal opening L-R: 820 mm Table surface area : 810 x 450 mm Slide area: 720 x 350 mm Hole in table: 600 x 110 mm Number of strokes: 100 - 1.000 s.p.m. Table height over floor: 1.030 mm Required power: 19,5 kW Weight of machine approx.: 6,8 ton

pressure: 63 t distance between columns: 650 mm stroke: 200 mm total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Capacity: 25 ton Throat depth: 250 mm Ram stroke: 6 - 60 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 190 mm Height of the bolster plate: 50 mm Table surface area : 500 x 400 mm Slide area: 350 x 250 mm Tool Clamping Hole Ram: 40 H7 mm Number of strokes: 160 s.p.m. Dimensions L x W x H: 1.300 x 1.500 x 1.995 mm Weight of machine approx.: 2 ton

pressure: 500 t passage width: 750 mm stroke: 120 mm total power requirement: 57 kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press capacity: 30 ton Throat depth: 160 Ram stroke adjustable: 20 - 45 mm Slide adjustment: 10 / 60 mm Shut height (stroke down, adjustment up): 220 mm Table surface area : 470 x 300 mm Slide area: 250 x 190 mm Number of strokes: 80 - 240 s.p.m. Required power: 4 kW Dimensions L x W x H: 1.400 x 1.800 x 2.000 mm Weight of machine approx.: 2,67 ton

pressure: 75 t throat: 280 mm stroke: 303 mm total power requirement: 15 kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press capacity: 40 ton Ram stroke adjustable: 8 - 50 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 290 mm Free frontal opening L-R: 600 mm Free lateral opening F-B: 190 mm Table surface area : 600 x 500 mm Slide area: 600 x 400 mm Hole in table: 500 x 110 mm Number of strokes: 65 - 400 s.p.m. Table height over floor: 1100 mm Required power: 32 kW Height over floor approx.: 2.800 mm Weight of machine approx.: 6,2 ton

Pressure total: 315 ton Ram stroke: 160 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 1.050 mm Free frontal opening L-R: 2.740 mm Free lateral opening F-B: 1.500 mm Distance between oil tray: 2.400 mm Table surface area : 2.740 x 1.800 mm Slide area: 2.400 x 1.700 mm Number of strokes: 10 - 60 s.p.m. Required power: 75,5 kW kW Working hours machine: 77.341 h Height over floor approx.: 5.500 mm Dimensions L x W x H: 5.400 x 3.300 x 5.700 mm Weight of machine approx.: 80 ton Control: Siemens S5

distance between columns: 300 mm table length: 3550 mm table width: 190 mm table height: 800 mm distance between columns: 3230 mm column arm: 300 mm weight of the machine ca.: 12,5 t dimensions of the machine ca.: 1600 x 3800 x 2800 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 40 t table length: 670 mm table width: 570 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 25 t throat: 250 mm stroke: 100 mm total power requirement: 7,5 kW weight of the machine ca.: 3200 kg dimensions of the machine ca.: 1000 x 1700 x 2600 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t passage width: NA mm stroke: 180 mm table length: 690 mm table width: 530 mm distance between columns: 420 mm total power requirement: 18 kW weight of the machine ca.: t dimensions of the machine ca.: m Hydr. 4-Pillar Press for Embossing/Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 3 t throat: 0 mm stroke: 200 mm total power requirement: 15 kW weight of the machine ca.: 4 t dimensions of the machine ca.: m Fully Automatically Straightening Press, 3 Stations,parts turning, (bolts) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 10 t throat: 0 mm stroke: 400 mm total power requirement: 7,5 kW weight of the machine ca.: 6500 t dimensions of the machine ca.: m D U N K E S (Germany) CNC Controlled Hydraulic Double Column Press Model HD 10 Year 1993 ________________________________________________________ Pressure 10 tons Ram stroke 400 mm Mounting height 600 mm Table size 400 x 300 mm Table height above floor 820 mm Ram area 400 x 300 mm Ram bore 40 mm Quickspeed, downwards, max. 70 mm/s Working speed, downwards, using max. pressure 40 mm/s Working speed, min. 5 mm/s Working speed adjustable from 5 - 70 mm/s Return stroke speed, min./max. 20 / 175 mm/s Drive 7.5 kW Total electrical load, approx. 12 kW - 380 V - 50 Hz Weigh ...

pressure: 63 t passage width: 1350 mm stroke: 300 mm total power requirement: 16 kW weight of the machine ca.: 10 t dimensions of the machine ca.: 2,0 x 1,8 x 3,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 500 t passage width: 750 mm stroke: 120 mm total power requirement: 57 kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 10 t distance between columns: 500 mm stroke: 200 mm total power requirement: 10 kW weight of the machine ca.: 4.500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 125 t distance between columns: 1050 mm stroke: 250 mm total power requirement: 40 kW weight of the machine ca.: 8,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 160 t throat: 360 mm stroke: 560 mm total power requirement: 33 kW weight of the machine ca.: 6000 kg dimensions of the machine ca.: 2000x2400x3650 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 150 t Table dimensions: 1000 x 360 mm voltage: 400 V total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Inclineable mechanical press with updated electrics (CE2004) and bolster plates. The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 8,5 kN stroke: 40 mm throat: 95 mm Working height from to: 95 - 240 mm table surface area: 160 x 110 mm spindle diameter: 25 mm weight of the machine ca.: 27 Kg dimensions: 160 x 230 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 8,0 kN stroke: 40 mm throat: 90 mm Working height from to: 50 - 200 mm table surface area: 120 x 160 mm weight of the machine ca.: 22 Kg dimensions: 160 x 230 x410 mm Knee lever hand press with fine height adjustment SPECIAL PRICE! • Working height adjustable by simply loosening the clamping screws on the stand • Working height fine adjustment for HK 800 = adjustment of the press head to the desired working height. The fine adjustment takes place forced in both directions via a threaded spindle • Hand lever arranged in a user-friendly manner, return via spring The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 4,5 kN stroke: 40 mm throat: 95 mm Working height from to: 95 - 240 mm table surface area: 160 x 110 mm spindle diameter: 25 mm weight of the machine ca.: 24 Kg dimensions: 160 x 230 mm Direct-acting pneumatic presses bring the full pressure performance over the entire stroke length. You will above all used when long-stroke parts are machined with constant force Need to become. Convincing technology • Long and precise spindle guide for maximum dimensional accuracy • Hardened and ground piston rod for practically unlimited service life • Double-acting cylinders with end position cushioning on both sides • Double guide rings in the piston, constant and quiet running • Oil resistant sealing elements Special features of the PND series • Spindle secured against twisting • Spindle return on the PND 85/S only via a cylinder chamber additional air savings • Easy,  ...

pressure: 2,5 kN stroke: 45 mm throat: 90 mm Working height from to: 80 - 220 mm table surface area: 120 x 60 mm weight of the machine ca.: 22 Kg dimensions: 160 x 230 x 390 mm Hand presses with rack HZ 250 The power is transmitted via a rack and pinion construction. she finds their use where during the working process a constant pressure is needed. Precisely manufactured, spindle hardened and ground, unlimited service life Long spindle guide, optimal pressure performance, T-slot according to DIN 650 milled in the middle, sliding blocks fit exactly. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 500 kN stroke: 40 mm throat: 73 mm Working height from to: 60 - 150 mm table surface area: 115 x 70 mm weight of the machine ca.: 10 Kg .Toggle lever hand press SPECIAL OFFER! • Working height adjustable by simply loosening the clamping screws on the stand • Working height fine adjustment for HK 800 = adjustment of the press head to the desired working height. The fine adjustment takes place forced in both directions via a threaded spindle • Hand lever arranged in a user-friendly manner, return via spring The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t stroke: 400 mm daylight longitudinal/sideways: 1300 /450 mm dayligth: 900 mm tank capacity: 75 l liter capacity: 22 l feed down: 6,9 mm/sec feed up: 12,6 mm/sec Motor output: 7,5 kW weight of the machine ca.: 2,1 t dimensions of the machine ca.: 2,0 x 0,75 x 2,8 m Presses can be operated both by hand and by motor. Cylinders can be moved sideways. Safety valve with cylinder end position. CE marking 2 year guarantee The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 20 t stroke: 180 mm daylight between the columns: 540 x 100 mm dayligth: max. 990 mm : 72 mm diameter of piston: 48 mm weight of the machine ca.: 0,12 t dimensions of the machine ca.: 0,8 x 0,7 x 1,8 m Our frame presses are officially CE certified according to the latest rules. Almost all presses offered in this area are not CE certified. - with manual hydraulics - Move the cylinder sideways - Pressure gauge - 2 press documents The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 10 t stroke: 180 mm daylight between the columns: 335 x 115 mm dayligth: max. 340 mm : 56 mm diameter of piston: 40 mm weight of the machine ca.: 0,05 t dimensions of the machine ca.: 0,75 x 0,53 x 1,6 m Our frame presses are officially CE certified according to the latest rules. Almost all presses offered in this area are not CE certified. - with manual hydraulics - Move the cylinder sideways - Pressure gauge - 2 press documents The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.