powder coating used for sale

Oven, doors single-sided, electric Dimensions: 3,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 54 kW Auxiliary heating: electrically indirect via thermoblock

Dimensions: Length: 7400 mm Width: 4000 mm Height: 3236 mm Extraction capacity: Q = 18000 m³/h P = 15 kW The cabin has a suction machine with filters to suck the powder from the cabin floor. The powder booth is set up in a pit to lower the entire height of the painting line. Manual doors are installed to enter the workpieces into the cabin. The overspray is extracted during powder coating via the floor. On the floor there is a grate for walking on and under the grate there is a second flat floor with automatic self-cleaning system, connected by air ducts with post-filter. A self-cleaning system automatically blows the powder from the bottom to the post-filter (suction machine) and consists of

Oven, doors single-sided, gas Dimensions: 4,500 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Recirculating air: Q = 12000 m³/h P = 2 x 2.2 kW Heat output: 69 kW Auxiliary heating: Gas indirectly via thermoblock

Chemical pre-treatment 3 zones for powder coating with spray ring (automatic) and manual Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Max. workpiece dimensions (automatic): Length: 6500 mm Width: 1000 mm Height: 2300 mm Max. workpiece dimensions (manual): Length: 6500 mm Width: 2500 mm Height: 2300 mm Tanks are positioned at ground level with a sloping floor. Tank No.1 is thermally insulated and is heated by electric heaters. Achievement: 27 kW. Volume of each tank = 1.00 m³. For degreasing (1st tank), a medium pressure pump is used to operate the 1st spray system. The rinsing phases are also operated by a pump with medium pressure via the 2nd spray system. On the bottom i ...

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

Chemical pre-treatment for powder coating (3 zones) 1 Dimensions of the cabin length 3900 mm Width 1600 mm Height 2500 mm 2 dimensions of the pre-treatment complete length 4000 mm Width 3000 mm Height 4000 mm 3 Passage opening width 1000 mm Height 1700 mm The chemical pretreatment for the use of nanotechnology or phosphating consists of 3 stages in 1 spray chamber. Chemical spray pretreatment works in time and this means that the workpieces are manually pushed into the chamber. After closing the doors, the passage starts and the pumps start spraying. Each pump has different spray times. After the spraying process is finished, there is an alarm indicating that the door can be opened and the workpiece can be pulled out. All pre-treatment functions a ...

Oven, doors single-sided, electric Dimensions: 3,000 x 1,700 x 2,000 [mm] (alternatively width 1900mm instead of 1700mm) Insulation: 150 mm (mineral wool 75 kg/m³) Temperature: max. 220°C Circulating air: Q = 7500 m³/h P = 3 kW Heat output: 46 kW Auxiliary heating: electrically indirect via thermoblock

The curing furnace consists of a tunnel furnace in which the workpieces are baked after coating. The furnace is a straight tunnel furnace. The frame is made of steel with insulated panels. The mineral wool insulation becomes 150 mm thick in a special construction to prevent thermal bridges 1 Inner dimension length 7,000 mm Inner dimensions width 1,000 mm Inner dimensions height 2,500 mm 2 Outer dimensions incl. thermoblock, length 7,200 mm Outer dimensions incl. thermoblock, width 1,300/2,300 mm External dimensions incl. thermoblock, height 2,800 mm 3 substructure 1 set of steel profiles 80 x 80 and 40 x 80 mm 4 walls 1 set of double-sided galvanized sheets 1mm, outside RAL 5010 5 Insulation 1 set of rock wool 150mm 75 Kg/m³ 6 Ventilation system 1 set of galvanized steel sheet 7 Temperature max. 220°C 8 fans 1 pc. 7,500 m³/h 9 electric motors 1 pc  ...

Open Powder Spray Stand Dimensions: 2500 x 2250 x 2700 [mm] Extraction capacity: Q = 8000 m³/h P = 5.5 kW Filter: 1 stage: Filter cartridges 4 pieces à Ø 325 x 1000 [mm] 2nd stage: Pocket filter (absolute filter for fine dust) Note: The overspray during powdering is absorbed by the suction unit. The powder spray stand is delivered on rollers and is therefore mobile

Dimensions: Length: 8000 mm Width: 4500 mm Height: 3500 mm Extraction capacity: Q = 18000 m³ P = 15 kW The cab has 2 doors on one side for the insertion/outlet of the workpieces. The components are pushed into the cabin for coating via the overhead transport system. Walls, ceiling and doors are made of panels. The filters positioned on the roof absorb dust and other particles from the outside, thus ensuring clean ambient air in the cabin. The overspray during powdering in the cabin is absorbed by the extraction unit

For sale is a Wagner WAC 70 circular saw in excellent condition, including a bundle loader. This high-quality machine is ideal for precise cutting and efficient handling of wood and workpieces in wood processing. Type: Circular saw Model: Wagner WAC 70 Additional equipment: Bundle loader Features of the Wagner WAC 70: Precision: The WAC 70 offers precise cuts for a wide range of wood types and formats. Performance: Robust construction for a long service life and high performance. Efficiency: The integrated bundle loader enables fast and efficient material feed, which significantly speeds up the production process. Operating Voltage: - Main: 400V, 50Hz - Control Voltage without transformer: 230V - Control Voltage with transformer: 25V Rated Current: 23A

Professional powder coating plant in excellent condition, available as of today. Picture 1: Blast cabinet • Year of construction: 2010 • 4x11 kW turbine • Maximum diameter 1.7 m • Maximum height 2.85 m • The blasting booth removes sharp edges and dirty oil layers from the raw material. In addition, blasting roughens the surface of the part so that the paint adheres better. Picture 2 + 3: Gema quick-change powder booth opticenter • Year of manufacture: 2013 • 10x automatic powder spray gun • 1x hand gun • 2x hydraulic work platform • It is possible to spray large surfaces partly by machine and small, more difficult areas partly by hand. Lost powder is extracted at the bottom, collected, and reused. Picture 4: Powder coating oven • Furnace dimensions: 20 meters long x 5.5 meters wide • Transport chain in oven: 45 meters long (Z ...

A complete bulk powder coating system MEEH powder coating and dust filter system is available. Product dimensions X/Y/Z: 8000mm/800mm/3000mm, max. product weight: 1000kg, total surface area of all openings: 12.9m², max. permissible powder injection quantity: 90kg/h, extraction capacity: 18000m³/h, total system dimensions X/Y/Z: approx. 28m/13m/6m, compressed air requirement: approx. 38nm³/h, compressed air: 8bar, connected load: approx. 30kW. 1) Manual powder stand with suction, internal dimensions X/Y/Z: 10m/3m/4m, external dimensions X/Y/Z: 10040mm/3370mm/4600mm. 2) Chamber dryer MEEH KTÖ240, year of construction: 2008, air capacity: 30000m³/h, heat output: 240kW, burner: Weishaupt, burner year of construction: 2019, fuel: heating oil, internal furnace dimensions X/Y/Z: approx. 8530mm/4610mm/5840mm, external furnace dimensions X/Y/Z: approx. 8200mm/3500mm/4000mm. 3) Lifting and lo ...

Complete professional powder coating plant in excellent condition, available from today. 00000 00000 00000 Turnkey delivery, we take care of all the work Control units from Gema We will respond to your inquiry immediately with all the details. Smooth processing, since 2010 With plastic booths, powder center, pump delivery, automatic guns, visual controls from Siemens Simatec 3D scanners, according to the latest technology... and of course pre-treatment with nano-coating Drive only e.g. 2 hours and look at a reference plant, one of many in the DACH region (since 2010) Contact us now, it's worth asking See PDF for all details powceq com (project page) , see also video here

For the automatic powder plant, conveys powder coating up to 20m in an even and 8kg quantity PDF with all details available, see also powceq com

Rail system for workpieces up to (as desired) 4m long and weighing 100kg Complete delivery, since 2010 in the DACH region Next reference page near you see PDF with all the details, see video Powder furnace, extraction stand for coating on both sides, can be upgraded with automatic coating equipment, be it Gema or Wagner Pow C EQ = Powder Coating Equipment We will respond to your inquiry immediately

Rail system for workpieces up to (as desired) 4m long and weighing 100kg Complete delivery, since 2010 in the DACH region Next reference page near you see PDF with all the details, see video Powder furnace, extraction stand for coating on both sides, can be upgraded with automatic coating equipment, be it Gema or Wagner Pow C EQ = Powder Coating Equipment We will respond to your inquiry immediately

Professional Grade Powder Device with Vibration Table Analog control, like new and 12 filters for powder booth in high industrial quality (extra price) Measuring instrument, unused, with full warranty, fully assembled Pick-up requested near Freiburg (D), shipping 150 Eur Scope of delivery Injector up to 300gr/min Control Unit Pro Analog Powder spray gun C2 (without remote control buttons) All cables and hoses Trolley and Vibrating Table Description Universal, processes almost all powder coatings and part structures Powder Coating Equipment 510 gram hand pistpole, flat spray nozzle Most important components from Switzerland Efficient and precise User-friendly rotary switch Car. Regulation of the charging voltage (mA) Fair prices on wear parts

Inv. Num. : 8867 Type: - Producer: Surfin Generated: Parameters: Inner width: 1250 mm Inner depth: 1250 mm Interior height: 2100 mm Equipment: 3x filter cartridge

With Ernst KG oven, 250 degrees Celsius, interior space 15m3, 380/230v. Dimensions L6150xW2340xH3200mm. Overhead conveyor system. Including various powder coatings Auction-ID: A1-44302-10

Folding former, folding machine, form folding machine, profiling machine, profiling system, slat production, blind production, dryer, infrared dryer, powder coating -Infrared dryer: used for powder coating slats/blinds production -Manufacturer: Himmel, type HA 5-2-9/500 -Geared motor: WEG 0.37 kW -Dimensions: 880/1050/H2200 mm -Weight: 308 kg

We sell an older but fully functional and complete TRIBO powder coating system consisting of - Through-baking furnace INDAPP approx. 8m x 4m, oil firing. - District conveyor with infinitely variable drive - 2 automatic cabins with 2 spray guns each - 1 hand cabin (self-built) - Hand sprayer TRIBO96C from INTEC - Suitable cyclones for powder recovery - Vibrators for powder screening - Extraction, powder filter The entire system is more than 40 years old, but fully functional and still in use. The TRIBO system works without high voltage, the charge is generated by rubbing the powder in the plastic tube of the spray gun. We have been using the system for about 40 years to paint housing parts made of sheet steel, which works very well and also economically fast. Please note: Sale from location. The system must be completely dismantled by the buyer. To do this, look at t ...

Manual Powder Coating System – Control Unit General data: Equipment type: Control unit (gun controller) for electrostatic powder spraying Weight: approx. 100 kg Dimensions (L x W x H): approx. 600 x 800 x 1100 mm Technical details: Power supply: 85 – 250 VAC Frequency: 47 – 440 Hz Air control: integrated connections for airflow regulation Description: Manual powder coating control unit designed for electrostatic powder spraying applications. The system allows precise control of coating parameters and airflow, ensuring efficient and uniform coating results in industrial environments. Auction-ID: A7-45351-5

3 x dosing systems, including 4 x PBS fluid tanks built in 2008 Auction-ID: A1-45447-20

With filter system ESB type AA 600 Compressed air protection class: IP54 Vibrating motor: 2 x 0.75 kW Fan motor: 2.2k W Total connected load: 6 kW Filter area: 2 X 72 m² Number of cartridges: 2 X 4 Extraction capacity: 6000 m³/h Air pressure maximum.8 bar Cleaning pressure: 7 bar, Including: 2 x ZA 02 lifting device, 8 Automatic powder gun type PG 2-AX, ESB control cabinet type 60191, Make number 600 Auction-ID: A1-45447-2

including 2 x PBS fluid tanks. Auction-ID: A1-45447-21

including 1 x PBS fluid reservoir. Auction-ID: A1-45447-22

Degree of protection: IP 54 (dust protection and splash water protection) Extraction capacity: 4000 m³/h Filter area: 30 m² Extraction capacity: 4000 m³ Dimensions cabin: 1900 x 1720 x 2720 mm (L/W/H) Auction-ID: A1-45447-19

With filter system ESB type AA 600 Compressed air protection class: IP54 Vibrating motor: 2 x 0.75 kW Fan motor: 2.2k W Total connected load: 6 kW Filter area: 2 X 72 m² Number of cartridges: 2 X 4 Extraction capacity: 6000 m³/h Air pressure maximum.8 bar Cleaning pressure: 7 bar, Including: 2 x ZA 02 lifting device, 8 Automatic powder gun type PG 2-AX, ESB control cabinet type 60191, Make number 600 Auction-ID: A1-45447-1

Box Width:750 Box Height:1000 dimensions of the machine ca.:1200 m2 Powder Coating Line EISEMANN very less used and in very good condition. New Price of the plant 2.600.000,- EURO Power & Free conveyor system with 250 car trains, 5-Zone Spray Pre-Treatment System, stainless steel - water drying cooling zones. 2 nos.of WAGNER stainless steel powder cabins each with ABB robots & double-automatic powder guns, as well aseach cabin is equipped with a hand-powder device. Powder Curing Oven, direct gas heated three-zone Spray cleaning equipment, Stainless Steel - Sewage Treatment Plant, Evaporator with Reverse Osmosis System & Fresh-Air Device. Opening Cross Section Areal: Width 750 mm, Height 1000 mm Technical Details: Pretreatment conveying speed 2.3 m / min. Pretreatment surface area approx. 200 m2 / h. Painting Surface approx. 120 m2 / h. Throughput of workpieces approx. 4,000 k This Powede ...

Used line for packaging of powdery materials in plastic buckets from 2.5 kg to 10 kg. Semi-automatic line of packing and transporting the dispenser weight The line consists of: Two unloading of big bags Oblique conveyor The buffer tank Two batchers Stacking conveyor The set of the transporters with the balance cruise control, feeder lids and closing buckets, made as part of the line for packing powdery materials. The line consists of: Conveyor separator Cruising verified checkweigher Discriminator transporter odstawiaj?cym Conveyor feeder lids Crimper Stacking Conveyor Appetizer - welding machine for bags The checkweigher DWT / xx Technical data: Supply voltage - Uz = 230V Isaiah znamionowy- current = 2-5A (depending on version) Mains frequency - f = 50 Hz overcurrent - F = 10A recommended network layout -TNS Insulation class - I New 2010

Ladies and gentlemen, we are happy to offer you milk powder in different categories partially durable up to 48 months. Please send us your request. We will be happy to answer your request. All prices are from Station Europa and the dismantling and all follow-up costs are to be made by the buyer. VAT is not included in the prices. The contractual agreements for the individual offers must be agreed separately and only apply after the contract has been signed. Mistake reserved. All technical details, dimensions, etc. are approximate and are non-binding for the supplier. The technical data are manufacturer or operator information and therefore non-binding for us. Used material is sold to the exclusion of any warranty. We do not accept any liability for used material. Warranty exchange and return are excluded. The material remains the property of the seller until f ...

with membrane conveying

Ladies and gentlemen, We are pleased to offer you a hand bagging machine. If necessary, we can send you pictures and specifications. Please send us your request. We will be happy to answer your request. All prices are from Station Europa and the dismantling and all follow-up costs are to be made by the buyer. VAT is not included in the prices. The contractual agreements for the individual offers must be agreed separately and only apply after the contract has been signed. Mistake reserved. All technical details, dimensions, etc. are approximate and are non-binding for the supplier. The technical data are manufacturer or operator information and therefore non-binding for us. Used material is sold to the exclusion of any warranty. We do not accept any liability for used material. Warranty exchange and return are excluded. The material remains the property of the  ...

Powder coating system for large parts Example:(all sizes can be changed individually) Space requirement: 30 x 15 meters Part size: L= 6,200mm W= 2,300mm H= 2,000mm Cleaning booth walk-in incl. spray wreath automatic 1 Dimensions of the cabin Length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Mass of tanks Length 1,200 mm Width 850 mm Height 1,000 mm 2 Dimensions of the cabin complete Length 9,140 mm including tanks width 5,580 mm Height 4,200 mm Coating booth walk-in, manual coating Lmmuapd8S 1 Dimensions cabin length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Dimensions of the cabin including extraction Length 10,125 mm Width 4,500 mm Height 3,400 mm Powder curing furnace 1 Inner dimension length 6,500 mm 2 Inner dimensions width 2,500 mm 3 Internal dimensions height 2,950 mm 4 Outer dimensions incl. thermoblock length 7,600 mm 5 Outer dimensions incl. ...

Powder fire make: CEAG Type: PG50-ABC Content: 50 kg There are a total of 4 pcs

1. Powder curing furnace 1,500 x 1,200 x 1,750 mm 2. Powder Coating Booth -KG DUO-01 3. Wagner powder coating plant, – Prima Sprint – 1. Powder curing furnace 1,500 x 1,200 x 1,750 mm 1 Inner dimension length 1,500 mm 2 Inner dimensions width 1,200 mm 3 Internal dimensions height 1,750 mm 4 Outer dimensions incl. thermoblock length 2,250 mm 5 Outer dimensions incl. thermoblock width 1,815 mm 6 External dimensions incl. thermoblock height 2,006 mm, 2,296 mm incl. exhaust pipe 7 Substructure 1 set of steel profile 8 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 9 insulation walls, ceiling 1 set of rock wool 150 mm, floor is insulated with 50 mm 10 Floor Furnace Gets 2 Entry Rails for Tray Wagons 11 Temperature 220°C 12 fans 1 pc. 2,600 m³/h 13 electric motors 1 pc 1.1 kW , 1450 rpm, 3 F, 50 Hz 14 Thermal power 14 kW 15 hinged doors, single ...

ULverein kiln 6,500 x 1,900 x 2,000 mm 1 Inner dimension length 6,500 mm Bidiwu73Sj 2 Inner dimensions width 1,900 mm 3 Internal dimensions height 2,000 mm 4 Substructure 1 set of steel profile 5 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 6 Insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m² 7 Bottom furnace gets 2 entry rails for tray wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 7,500 = 15,000 m³/h 10 electric motors 2 pcs 2x 3 kW , 1450 rpm, 3 F, 50 Hz 11 Thermal power 110 kW 12 hinged doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m² Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heater electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burners 1 pc stove is electrically heated 15 Exhaust air 1 pc device for exhaust air pipe, manua ...

Power: 11 kW, 50/60 Hz 2930 rpm Connections Tri Clamp Condition very good Dimensions LWH: 1000 x 400 x 900 mm Weight: approx. 150 kg

Y.O.M.: 1995 No.: P5050781 Power: 11 kW, 50/60 Hz 2920 rpm Connections Tri Clamp Milk Pipe DN50 Condition very good Dimensions LWH: 900 x 400 x 850 mm Weight: approx. 150 kg

Y.O.M.: 2007 No.: 07071151 Power: 5.5 kW with funnel and fitting for powder very good condition with operating instructions Dimensions LWH: 950 x 460 x 1200 mm Weight: approx. 160 kg

Stock# U2308-7 Used stainless steel contact parts polish made V type tumbling blender with total volume 4500 l. Working volume 3000 l. Mixer has two inspection/feeding inlets with bolted lids, each with diameter 450 mm. Central conical discharge with diameter 245 mm, with manually operated valve. There is an internal supporting shaft/baffle inside the mixing chamber. Machine is driven by el. motor 18.5 kW, 1480 rpm, 380 V, 50 hz, through belts and gearbox type WD650. Working rotation of mixing chamber up to 8 rpm. Supporting frames and operating platform designed in carbon steel. Includes technical documentation.

Machines are still in use. Will be available soon. Pictures and technical data on request.

Fire extinguisher, powder extinguisher -Fire classes: A, B and C -Chassis: with solid rubber tires and swivel caster -Nitrogen bottle -10 m high-pressure hose: with lockable extinguishing gun -Dimensions: 600/450/H1050 mm -Weight: 120 kg

press is after overhaul: full function complete mechanical parts, pneumatic and control system. The press has a new pneumatic clutch, the original was electromagnetic clutch as old system. Press capacity: max. 45 t Pull force: max. 45 t Counter force in pressing position: max. 17 t Stroke of the punch: 175 mm Filling height: max. 140 mm Deduction: max. 85 mm Compression distance: max. 55 mm Top pressing: max. 15 mm Stroke rate: 9 – 26 min.-1 Motor: 7,4 kW Approx: 3000x1200x1800 mm Net weight: about 5000 kg

Brand new wooden powder trays for mogul plants, quality, long-life cycle, material, precision analog to Treiber, stackable, appropriate for all mogul lines, tested for NID, W&D, MAKAT, BOSCH, partially already certified by the manufacturers of the line send your price inquiries to company SCHOKOMA GMBH indicating quantity of trays, bottom material, dimensions inside and outside, delivery possible

Press capacity: max. 45 t Pull force: max. 45 t Counter force in pressing position: max. 17 t Stroke of the punch: 175 mm Filling height: max. 140 mm Deduction: max. 85 mm Compression distance: max. 55 mm Top pressing: max. 15 mm Stroke rate: 9 – 26 min.-1 Motor: 7,4 kW Approx: 3000x1200x1800 mm Net weight: about 6000 kg

BATES Fully automatic valve bag filling, Thermal valve welding, 140 – 180 bags / hour (25 kg, 50 kg), food/non-food, refurbished, like new Description SPECIFICATIONS Valve bag filling, manufacturer Bates, year of construction 1992. The system is designed for the bagging of dry, fine powder in valve bags, whose valve width V = 135 mm (clear width). Since all parts in contact with the product are made of stainless steel, this system is suitable for both the food and non-food sectors. (From a purely technical point of view, ATEX is also fulfilled – but there is NO longer any guarantee for this.) Depending on the product and its characteristics, the production capacity of 25.0 kg bags is approx. 140 – 180 bags/hour. Of course, the system can also process 50.0 kg bags. The offered installation consists of several components: 1. 60FFED fully automatic filling machine  ...

The machine was dismantled at the end of 2021 and has been stored in a hall ever since. The packer is complete with control cabinet and its own compressor. The wiring to the control cabinet was documented during dismantling. Instruction manual on German is also available.

Used automatic packaging machine by IARO. The IARO machine is designed for packaging of granulated and chunky products such as: tea, coffee, groats, rice, etc. and powdered products such as: coffee powder, milk powder, etc. And powdered products such as: ground coffee, milk powder, etc. Technical data: -Mechanical capacity: 20-90 cycles/min. -Operating capacity: 20-50 packs/min (depends on the type of product being packed and the portion size). -Standard bag width: 60-160 mm. -Standard bag length: up to 400 mm. -Size of the portion-standard: max. 2000cm3. -Control and drive of the machine: Electro-pneumatic. -Compressed air pressure: 0.6 MPa. -Air demand: -version with blower: max 25m3/h, -Version without blowing: max 15m3/h. -Electric supply: 400V/50Hz. -Power (without metering): 8 kVA. -Dimensional dimensions: (dł.szer.wys.) 130012001900 -Mass (without dispens ...