pos used for sale

Bode welding derrick for internal amp; external submerged arc welding - for welding tanks - welding length: 3500 mm - Esab LAE 800 amp welding unit for external arc welding - Esab LAE 800 amp welding unit for internal arc welding - max height of workpiece: 6200 mm - heightadjustment is in increments of 250 mm - hydraulic clamping of workpiece - movable welding rotator 40 ton - electric movement gt; wheeldia 480 mm x 200 mm wide gt; rubber wheels MANIPULATOR: welding derrick

Single-shaft shredder particularly suitable for secondary shredding, granulation of pre-shredded material. Application: Commercial waste for thermal or recyclable recycling, e.g. paper, cardboard, art and foams, rubber, leather, textiles, floor coverings. etc. Lindner Komet 2800, overhauled machine 02/2024 Year of construction 2015 Control cabinet with FÜ ABB, dustproof with dry cooler Control panel: new Drive motors : ABB 2x160 kW Paint New/RAL: 5003/7001 Rotor bearings/squeegee/shaft seals : new Wear plates: stainless steel R+L New Knife holder: new All knives/screws : new Sealing ring rotor: new Sealing ring wall: new Terminal strip top: new Terminal strip bottom: Refurbished Counter knife carriage: Recycled Scraper comb beam with sheets: new Gaskets, brackets, bolts, locking bolts: used very well preserved Adjustment screws (counter knife, scraper comb): new Slidi ...

Automatic feed via control E 355 P For attachment to any Elumatec single-head saw (right) Max. feed length: 3000 mm With glazing bead caliper

Hydraulic levelling unit for aligning workpieces on welding rotators

We offer here a very robust rotary tilting table for machining parts up to 2000kg (according to load diagram). The manufacturer states tilt safety without fixing the positioner. We have attached 2 safety angles at the back. These are included. Unfortunately, this positioner did not work for its intended purpose. It is not height-adjustable, which is why we built a platform out of 5mm tread plate (4800x2900x300 /steps 2x150high, all-round 400 deep, weighing approx. 800kg), which is also included if needed. Due to very little use during the test phase of the introduction of a new product, the turn - tilt table is as good as new. It is set to tilt from 0° - 90° but can tilt from -20° - 120°. Transport is not included, but can be organised. The unit is still assembled and connected, so it can be inspected. CE declaration of the manufacturer is included. Bought as seen. We do not offer ...

Important set of BLAAHOLM 100T welding positioners consisting of: 5 idlers welding positioners with double bandage, capacity 100T, year 2013 5 motorized welding positoners with double-bandage, capacity 100T, year 2013 2 fit-up welding positioners with single bandage, capacity 100T, year 2013 3 idlers welding positioners with double bandage, capacity 100T, year 2018 (New condition) 2 motorized welding positioners with double-bandage, capacity 100T, year 2018 (New condition) 1 fit-up welding positioners with single bandage, capacity 50T, year 2018 (New condition) This set was operated by a company producing Wind Tower wind turbine masts The equipment can be sold together as a batch or separetely in sets.

Brand: Oerlikon / SAF Model: LP100 Year 2009 Type: Self-aligning/Self-centering Capacity: 100T Diameter range: 2000 to 4500 mm. Turning speed: 100-1200mm/min. Wheel width: 235mm Wheel diameter: 450mm Distance between translation wheels: 1930mm between tabs Translation speed: 4m/min. It has a cable control with buttons for the direction of rotation, speed variator and translation of the turner. Power: Three-phase 380V They have manual and Ce.

Position switches, limit switches, single limit switches, BALLUFF BNS006E BNS 819-100-R-11 ( BNS819-100-R-11 ) 1 ram 250 V AC 5 A 1 NC, 1 NO contact New ! Dimensions ( position switch ): 51 x 47 x 22 mm

Regenerative afterburner, manufacturer: KRANTZ, type: Ecoline 2 23,500 Nm³/h, year of manufacture: 2005, serial no.: G-8321161-2, with pre-filter or cartridges for RNV, roof passages must be professionally closed by the purchaser!

Pre- and post-heating coil, air heating element, DN125, 371550, LHE 125 IS, Dimplex, new Special price We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition in original packaging! The part was purchased from a spare parts warehouse of a company and has never been in operation, is in a completely mint condition and in its original packaging. Dimplex - 371550 - LHE 125 IS Air heating element Electric pre- and post-heating. 0.75 kW electric heating coil (power-controlled) for pre-heating the outside air or post-heating the supply air, thermally insulated, with temperature switch adjustable from -30°C to +30°C, air flow monitor for detecting the smallest air flows at minimum operation and two safety temp ...

We offer directly on behalf of the owner : Bending press, second-hand Make : Graebener Maschinentechnik (Gräbener) Type : GRNM Year of construction : 2005 Flexural force max.: 16.000 kN ( 1.600 t ) Tool length : 1,600 mm Data at 520 N/mm2 Pipe diameter max.: 1,524 mm Tube diameter min.: 457 mm Sheet thickness max.: 40 mm Max. pipe length: 13.2 m Pipe length min.: 6m Pipe weight max.: 25 t Total power requirement approx.: 245 kW / 400 V / 50 Hz Approx. space: 27 x 3 m Total weight approx.: 90t / basic machine approx. 65t Further technical data and details on request or see data sheets in photos / PDF The machine was built in 2005, worked until 2021 and was professionally dismantled and packed for transport.

Pre- and post-heating coil, air heating element, DN160, 366260, LHE 160 IS, Dimplex, new Special price We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition in original packaging! The part was purchased from a spare parts warehouse of a company and has never been in operation, is in a completely mint condition and in its original packaging. Unfortunately the type plate has come off - special price Dimplex - 366260 - LHE 160 IS Air heating element Electric pre- and post-heating. 1.5 kW electric heating coil (power-controlled) for pre-heating the outside air or post-heating the supply air, thermally insulated, with temperature switch adjustable from -30°C to +60°C, air flow monitor for detecting the sma ...

- Mutton NZ 700 E - Year of construction 2007 - incl. magnet - Incl. all-metal detector and ejection - Incl. feed belt and discharge belt - good condition

Inductive Single Position Switch, Inductive Sensor BALLUFF BES02MM BES 517-110-RK 10 - 60 V DC Reach: 2 mm Connection: Screw terminals, 4-pole Material: PA 12 ( Active Surface ), PA 12 ( Housing Material ) New ! Dimensions (sensor): 63 x 60 x 12 mm Dimensions (packaging): 140 x 80 x 20 mm

Mechanical single position switch, 2 pcs BALLUFF BSE0008 BSE 44.0-RK switching capacity ( DC ): 220 V DC 0.5 A, 24 V DC 4 A switching capacity ( AC ): 250 V AC 6 A, 40 - 60 Hz connection: Screw terminals, 4-pole contact system: Dual circuit changer ( one normally open and one NC, galvanically isolated ) Material: Thermoplastic ( lid, housing ), Contact material: fine silver, gold-plated New ! Dimensions ( switch ): 60 x 29 x 13 mm Dimensions ( packaging ): 140 x 80 x 20 mm

Mechanical Single Position Switch SIEMENS 3SE5112-0CH01 Switching capacity ( DC ): 24 V DC 3 A switching capacity ( AC ): 240 V AC 6 A, 50 - 60 Hz Umax.: 400 V Connection: Screw terminals, 4-pole contact system: one NO and one NC Material: Metal ( Enclosure ) New, with underlays ! Dimensions ( switch ): 130 x 41 x 60 mm dimensions ( packaging ): 170 x 170 x 80 mm

Inserter FRANCOTYP-POSTALIA FPi 5600, 5 feeders, 2 feeder trays missing, envelopes approx. 4000 letters per hour, fold type: single, double parallel, Z and wrapping fold

Inserter FRANCOTYP-POSTALIA FPi 5600, 2 feeders, envelopes approx. 4000 letters per hour, fold type: single, double, parallel, Z and fold, vertical tape tray

Description: Six pieces, without contents Approx. Onsite Dimension. (l x w x h): 5,700 x 400 x 1,950 mm, weight approx.: 500 kg

Digital position indicator, 1 - axis BRUNNER ELEKTRONIK RPU 80 308. 2.121 5 digits 110 / 220 V 50 Hz approx. 1.7 m power cable approx. 3.0 m measuring cable used, tested ! Dimensions: 270 x 260 x 140 mm

Description: With a stock of measuring fittings, screw couplings, gas filling valves, measuring nozzles, centrifugal wheel trolleys, screws and other spare parts for pumps Approx. Onsite Dimension. (l x w x h): 3,650 x 600 x 1,950 mm, weight approx.: 1,000 kg

Description: - Trolley, 5 pieces - With wheels for rails - Roller width 1000 mm, roller diameter 60 mm, height from floor approx. 250 mm - 5 x roller track length 2000 mm Approx. Onsite Dimension. (l x w x h): 2,000 x 1,300 x 1,200 mm, weight approx.: 350 kg

Description: main engine power: 1 kW serial number: 9915 pneumatically driven pressing length approx. 2500 mm tabletop approx. 2500 x 620 mm with electronic temperature control safety light barriers dimensions in mm: approx. 3200 x 1500 x 1900, weight in kg: approx. 1300 serial number: 9,915, Approx. Onsite Dimension. (l x w x h): 3,200 x 1,500 x 1,900 mm, weight approx.: 1,300 kg

Description: Consisting of 2 pieces Jaw width: 100 mm and 145 mm Approx. Onsite Dimension. (l x w x h): 500 x 330 x 200 mm, weight approx.: 30 kg

Description: Consisting of 3 pieces One of them is manufacturer SPREITZER Jaw width: 100 mm, 100 mm and 125 mm Approx. Onsite Dimension. (l x w x h): 600 x 300 x 140 mm, weight approx.: 120 kg

Description: Consisting of 3 pieces Jaw width: 250 mm, 250 mm and 200 mm weight approx.: 150 kg, Approx. Onsite Dimension. (l x w x h): 500 x 300 x 150 mm

Description: Consisting of a three-jaw chuck (diameter: 220 mm), another three-jaw chuck (diameter: 160 mm), a third three-jaw chuck (diameter: 100 mm), a fourth three-jaw chuck (diameter: 150 mm) and another three-jaw chuck (diameter: 160 mm) weight approx.: 150 kg, Approx. Onsite Dimension. (l x w x h): 600 x 400 x 200 mm

Description: Consisting of 11 pieces Type: B25/120 and BH30130 weight approx.: 50 kg, Approx. Onsite Dimension. (l x w x h): 500 x 330 x 150 mm

Description: Consisting of a three-jaw chuck, manufacturer RÖHM (diameter: 200 mm) and two three-jaw chucks, manufacturer SCHUNK (diameter: 160 mm, 160 mm) Also various bases for jaw chucks weight approx.: 150 kg, Approx. Onsite Dimension. (l x w x h): 700 x 560 x 150 mm

single-sided direct postforming machine Brand: Wehrmann Type: Combima /K/I/R80/1260/V Year: 2018 Varied using for doors, worktops, furniture parts, curved caravan fronts, etc. Technical data: A single-sided throughfeed postforming machine for the postforming and postfolding process, for processing curved workpieces in caravan construction. For workpieces to be profiled made of wood/wood materials with laminate (CPL,HPL) as surface material. The laminate protruding for the postforming process is located in the machine on the underside of the workpiece and is formed from the bottom to the top. Technical data Machine Constant workpiece projection from the chain conveyor: from approx. 35 mm Throughput width min.: 130 mm ( only for straight parts ) Workpiece length in feed direction min.: 1,000 mm Basic height: 940 mm (upper edge of chain conveyor) The workp ...

Single sided postforming edge processing machine Brand: WEHRMANN   Type: Combima DPF New with 12 months warranty Example with typical equipment; almost each equipment is possible.  Please discuss your requirements with us  Technical data: Machine control: BECKHOFF route control with 15? Touch-Screen for pre-selection of units and for saving programs.  The workpiece transport via precision roller chain R75 with height adjustable top pressure.  Feed speed: max. V=6-30 m/min.  frequency controlled drive,  Top pressure: Motorical height adjustment via axis adjustment in program Right hand site equipped with 1 unit, width adjustment via NC axis: 1 Pre-milling unit With 1 motor with vertical shaft,  400 V, 12,5 KW, 100 Hz, 6000 rpm. Motor shaft Hydro D40 Swivable 90 - 180 degrees, move in/out for use Left han ...

Vertical CNC machining center Manufacturer POS Type PosMill 1100 Year of construction 2008 Control Heidenhain iTNC530 approx. 18,700 spindle hours Travel X/Y/Z 1100/600/400mm 10,000 rpm 40 fold tool changer IKZ Machine is in very good condition

Inv. Num. : 5987 Type: POS-20 Producer: PPP IDEAPRO Created: 2021 Parameters: Power consumption: 2.2 kW Required exhaust air volume: 5000 m³/h Power: 20 t/h Device operating temperature: 5 C Current Conditions: 3/N/PE 400V 50Hz Weight: 1350 kg Rotary screens are used to separate contaminants from various loose dry and wet free-flowing materials.

FEEDING belt feed belt, conveyor belt for t, Posch, Hakki, BGU, splitting machine! Original version for woodworking! Do-it-yourself! DIRECT FROM THE MANUFACTURER! -New, open with mounted alligator connectors, 1-ply reinforced top cover, + bottom cover made of felt, antistatic (also from rubber-Supergrip profile available)! -Dimensions: length heavily 4.420 mm long x width 200 mm x 6 mm Item will be shipped with UPS! On request we can cut the belt conveyors / conveyor belts to your individual measurements. (All lengths and widths possible) Endless connection on request. Additional versions, with pimples, Stollen or structured surfaces available. Not is your desired size? No problem! We customize for you! More transport and conveyor belts in all other sizes available immediately . We ship worldwide we deliver worldwide, please ask for shipping costs!

1 of used pneumatic, column-mounted, industrial manipulator / lifting device (balancer), make Dalmec, type Posifil PFC, new 2014! (excellent condition). Standard column 2.000 mm tall with 470 mm extension. Designed for a maximum lifting load of 30 KG. Maximum radius 3.000 mm. Vertical stroke 1.800 mm. With console and special gripper for bags. Can be retro-fitted with a standard console for safety- or jerry-can hook at additional cost. Visible frame is for transport purposes only and not included (available at additional cost).

Marking - Station with discharge and attached roller-tube Length: 4700 mm Total height: 2000 mm

Used from plant disassembly. Siemens Simodrive Posmo-SI with Alpha gearbox Engine: 6SN2500-2BF00-0GG0 Transmission: TP 050-MF1-5 -071-000 Dimensions L x W): approx. 65 x 25 cm The machine is electrically tested before sale and receives a DIN VDE 0113 test report.

table diameter: 900 mm table load: 1.000 kg turning speeds: 0,12 - 1,2 U/min swivelling range: 0 - 135 Grad speed: Kipp 0,35 U/min welding current: 500 A dimensions of the machine ca.: 1475 x 1050 x 900 mm For heavy industry When choosing a turntable, it is essential Turning and tilting torque must be taken into account. To note applies to how far the center of gravity of the workpiece is from the The faceplate is away or how far the center of gravity is is eccentric from the center. By means of a Rotary and tilting tables can be used to optimize workpieces position for welding. - Robust construction. - Infinitely variable. - Hand remote control. - HF protected. Furnishing : - 1 control (integrated) - 1 wired remote control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

1 of used pneumatic, column-mounted, industrial manipulator / lifting device (balancer), make Dalmec, type Posivel PVC-26, new 2011 (excellent condition). Column 2.350 mm tall. Designed for a maximum lifting load of 36 KG. Maximum radius 2.600 mm. Vertical stroke 1.400 mm. Fitted with 71 mm diameter expander-type gripper for tubes with 90-degree (vertical/horizontal) swivel motion. 2 units available. Visible rack is for transport purposes only and not included (available at additional cost).

- technically efficient, ready to work – after full service - working length: 2600 mm - electronic positioning (servo drive) - quick card (60 items)

X = 6000 mm Y = 2000 mm Quill = 1250 mm Positioner L = 6000; load capacity 20 tons Year of manufacture/SO/GO: 1979/-/2001

full automatic with chipconveyor cap round: 420 mm cap square: 420 x 420 mm cap rectangle: 420 x 420 mm Depth of throat: 420 mm Max height of workpiece: 420 mm Table travel : Manual (1) -- hydraulic (2): hydraulic (600 mm) Sawspeed: 17 > 120 m/min Length of band saw: 6300 x 41 x 1,3 mm Power needed: 8 kW Length : 2450 mm Depth : 3050 mm Height: 2230 mm Weight: 3400 kg

NILFISK- Mobile cold water high-pressure cleaner-MC 2C-150/650 XT (POSEIDON 2-29 XT) Product Name: Mobile cold water pressure washer Type: MC 2C-150/650 XT (POSEIDON 2-29 XT) Manufacturer: Nilfisk Item number: 128470138 Year of construction: 2020 Condition: Brand new technical details: - Brass cylinder head - 3 x ceramic coated pistons - Automatic start/stop for long service life - Water volume regulation - Universal Plus lance with 4-in-1 nozzle - Steel-reinforced high-pressure hose - Removable 2 l detergent tank - Pressure: 150 bar - Pump speed: 2,800 rpm - Suction height (filled): 0.5 m - Cleaning effect: 2.9 kg/f - Water capacity qmax: 650/570 l/h - inlet temperature: 60 °C - electrical connection values: 230 V/1-phase/50 Hz/14.5 A - Power consumption: 3.3 kW - 5 m power cord - Hose DN6 15M on hose reel - Nozzle size: .0370 - integrated HD detergen ...

The Posimat PB 80 is a pneumatically operated handling device. Version : with counterweight, suspended from on-site steel construction. Specifications: Load capacity: 120 kg; Hub; 1,600 mm; working range (radius) 2,600 mm; dead weight without counterweight and column: 150 kg The device was only in use for a few months.

Boat accessories, ship accessories, spreader schooners, mooring schooners, fenders, lifeline cushions, railing schooners, boats, ships -approx. 180 positions boat accessories - see photos -we can send you the complete photos of the positions - will only be sold complete

Assembled Knife Holder for CPM 7930 Model 30-4 Knives included

7TH & 8TH AXIS POSITIONER (CUSTOM) We provide industrial robotics and engineering solutions as well as custom positioner production according to your project needs. Please contact us for further information.

HM Corner - Cutter Head - Face Milling Cutter with Inserts. Diameter: 315 mm. Height: 90 mm Bore diameter: 62 mm. Number of inserts: 18 pieces Dimensions of the inserts: Rectangular, 12.8 x 12.8 x 5 mm, positive. Good used and ready to use, without damage to the panel seats. Shipping possible in consultation with the forwarding agent. or self-collection. The part can be viewed in consultation and is immediately available.