We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
120,294 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
4000 x 2000mm 6000w
new
Description: Type : ÖLtransformator Version : Hermetic Make : CG POWER SYSTEMS Belgium NV B7ssq0vkzj Year of construction : 2012 Condition : New with 1 year warranty Rated power : 3500 KVA Medium voltage : 33 KV +- 2 x 5% Low voltage : 400 V Switching group : Dyn 5 Frequency : 50 Hz Cooling type : KNAN Total weight : 7750 Kg Oil weight : 1720 kg Synth. ESTER Length : 2400 mm Width : 900 mm Height : 2250 mm + 160mm cable flag Other sizes and voltages also available from 100 KVA to 3500 kva . All transformers are tested and ready for use and immediately available from our warehouse in 59557 LIPPSTADT . Nationwide delivery . For further questions available Mon to Sat. 8 a.m. to 10 p.m.
new
- engine power: 1.1 kW - dial diameter: 300 mm - cut from below - cutting at an angle of -45 °, 90 °, + 45 °, intermediate angles set manually - vertical pneumatic pressure - protective cover - cooling installation
used
Fixed and live bushing - Iemca Smart 320/32 new in 2018 - very well equipped - chip conveyor - Mitsubishi M70 Control
used
Paneling Finn-Power Bending Automation Mod. Bending Cell Type BC 2550 200 year 1999 Hours: 27.800 This machine is in good condition and worked for few hours. I point out to you that there is an oil leak wich comes from a cylinder. The machine is functioning and in case of your visit, it can be connected again.
used
Technical data for the pallet racking system: Shelving system: Polypal Type: Stockpal Technical data for installation: Number of shelf rows: 01 pcs. Length per row of shelves: approx. 12,010 mm Number of fields / shelf row: 05 pcs á 2,300 mm Number of levels plus floor level: 02 pcs. Included in delivery are: 06x pallet rack stand, used Material colour: similar. Ral 7021 anthracite grey Stand profilem.: P 85 x 63 x 2,00 mm Incl. transverse and diagonal struts, Base plates The stands are pre-assembled ( screwed truss ) 2,000 mm high 1,100 mm deep 20x pallet rack trusses, used Material color: orange Box profile: 120 x 50 mm Traverse type: SKVBN11850NP22 Agraffe: 5 HK Clear width: 2,700 mm load per pair of trusses 2,400 kg, with the same. distributed load 40x safety pins, used Material color: ...
used
Size: 20.32 x 20.32 cm Equipments: good condition without any damage 4 machines Available 8 x 8 and 8 x 5 air pillows.
used
Servomotor MOTOR POWER ESA 3S 1018 with encoder ELTRA EH38M500Z8/24P6X3PR666
used
Servomotor MOTOR POWER ESA 3S 1304 with encoder ELTRA EH38M500Z8/24P6X3PR666
used
Polyketting Conveyor belts - conveyors with min. 19 pieces frequency controlled motors for Tetra Pak beverage cartons Approx. 100 meters
used
Polyketting Conveyor belts - conveyors with min. 19 pieces frequency controlled motors for Tetra Pak beverage cartons Approx. 100 meters
used
used
used
used
Digital program 999 positions Air table, In production Free of damages
used
Used Polar vibrating tables without function for cannibalization.
used
Cutting machine Polar 137 EMC, air table, light barriers, program control, year of construction 1982, machine number 5204605, in good condition, immediately available
used
Housing/partition wall for Polar cutting machines or stackers; width 228cm; Height 180cm. Housing/dividing wall for cutting machines or lifters Polar; width 228cm; hight 180cm.
used
Cutting machine Polar 72 CE, working width 72cm, periscope visor, year of construction 1976, machine number 4651681, in good condition, immediately available
used
PONAR ŻYWIEC UT-090 H injection moulding machine was manufactured in 2001 in Poland. The machine, designed for plastic injection moulding, is equipped with high-end components, increasing productivity and ensuring high reliability. Located on the body of the injection moulding machine, an operator’s panel with an installed MOOG-BUHL CNC controller allows for complete automation of the injection process and control of parameters. Moulds with a minimum height of 225 mm, mounted on 615 x 615 mm platens, are closed with a force of 90 tonnes by a hydraulic clamping unit protected by fixed and movable guards. The combination of the high clamping force of the mould, together with a powerful screw with a diameter of 30 mm, guarantees the best quality of the manufactured products. The extensive equipment offered with the UT 090 H injection moulding machine includes a pneumatic plastic feede ...
used
Manufacturer: Infastaub GmbH Model: Infa-mat AM 451 S Year: 2015 Type: bag / pocket filter Filtration area: 45 m2 Air volume: 4020 m3/h Housing resistance: up to +/- 35 mbar Fan power : 5,5 KW Soundproof housing Automatic and mechanical cleaning of the filters after the process by a vibratory drive Dust collection: bucket
used
Cutting machine Polar 72 CE, photoelectric sensors, working width 72cm, year of construction 1979, machine number 4951509, in good condition, immediately available
used
Manufacturer UNIVERSAL LATHE POTISJE EXCELLENT CONDITION, USED ONLY FOR SUPERFINISH AFTER GRINDING Model PA-45 Year Condition used Location Slovenia Price 26.500,00 € Category Lathe Subcategories Stock Number Serial Number Max turning lenght 3000mm Turning over bed 600 mm, Spindle bore 140 mm, Turning in cranking 1.200 mm Face plate 800 mm
used
Impact crusher Pozzato 8-5-3 Machine width 500 mm Rotor diameter 800mm, 3 impact bars Capacity up to 40 t/h Feed size approx. 50 mm Sand content in the crushing product up to 50% Machine on base frame Older year of construction with very few operating hours
used
Cutting machine Polar 78 X, air table, light barriers, program control, back table cover, 2 spare knives, knife change holder, year of construction 2008, machine number 7861423, in good condition, immediately available
used
liter capacity: 625 / min l feed pressure: 0 bar coolant capacity: 200 l total power requirement: kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 0,8 x 0,6 x 1,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Center height: 700 mm Center distance: 4000 mm Spindle bore: 90 mm Swing over bed Ø: 700mm Swing over cross slide Ø:500mm DBC Turning Length: 4000mm Spindle bore: 90mm Spindle power: 8kW Bed width: 400mm Tailstock spindle Ø: 5Ø Stroke pinole: 80mm Spindle taper: 185Mk Speeds / ranges: 2000Rpm Length: 5825mm Width: 1400mm Height: 1800mm Weight: &nb ...
Turning diameter: 1900 mm Turning length (Z-axis): 2500 mm Spindle bore: 102 mm Turret positions: 0 Motor power: 45 HP/kW Chuck diameter: 500 mm Swing over bed Ø: 1900mm Swing over cross slide Ø:1520mm DBC Turning Length: 2500mm Spindle bore: 102mm Spindle power: 45kW Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Length: 6800mm Width: 2800mm Height: 2800mm Weight: 10000kg
used
Edge press with preheating device, hydraulics, clamping length 2500 mm, mobile.
used
Polar 115X guillotine Polar RAB4 jogger + Bizerba scale Polar LW-1000 lift
new
Depalletizer is used for unloading new bottles, delivered on pallets. After clamping one whole row from bottles layer by gripping head, the device delivers them to the unloading table, and the bottles are transported to the washing machine or filling machine. - Capacity up to 6 000 bottles / hr. - Operation - 1 person - Dimensions of bottles: - diameter 20 to 120 mm - height from 50 to 350 mm - Lifting height to 4m, - lifting capacity – to 40 kg - Lifting speed - 7m / min - Speed - 7 m / min - Enviroment temperature - 5 to 45 degrees C - Total power requirement - 0,8 kW - Air Pressure - 0.5 - 0.6 MPa / stable /
new
pressure: 100 t stroke: 380 mm table surface area: 1740 x 996 mm pressure: 258 bar ajustment speed: 7,54 mm/sec work speed: 2,47 mm/sec return speed: 9,06 mm/sec dayligth: 700 mm table height: 720 mm total power requirement: 2,2 kW weight of the machine ca.: 1685 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
swing diameter: 430 mm centre height: 450 mm total power requirement: . kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
swing diameter: 430 mm centre height: 450 mm total power requirement: . kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Potain 7,5 ton x 24 meter
used
-Year 1990, Jogger with air press roller -Max paper size 1450x1130 mms. -Blowing plane -Folding squares on both sides -Height of introduction 16.5 cm -Max operating pressure 6-7 bar -380 V power supply
used
Technical data for the compensating plate: Manufacturer: Polypal The scope of delivery includes: 01x compensating plate, used Total width: approx. 130 mm Total depth: approx. 85 mm Material thickness: approx. 1.50 mm Borehole Ø: approx. 15 mm Number of boreholes: 2 pcs. Weight: approx. 0.12 kg | Pcs.
used
Type: Turret punching machine Finn Power Model: C5 YOM: 2007 Capacity: 30 Ton Maximum Sheet Thickness: 8 mm Maximum Sheet Size: 2530x1270 mm Minimum Sheet Size: 300x100 mm Maximum Sheet Weight: 200 kg Number of Stations: 20 Turret Speed: 24 RPM The machine is still working. You can do an inspection. On request, I will send additional information and photos.
used
chamber volume: - liter useable volume: 1,6 liter friction: - motor drive power: 22 kW Condition: used - overhauled Specification: Laboratory internal mixer - second-hand - chamber volume: approx. 1.6 l - closing system: front door with pneumatic piston - plunger: pneumatic - rotor geometry: tangential type - Oil-free self-lubricating sealing rings - New rotary union for water cooling - New main gearbox - New AC motor: 22 kW - Control cabinet: NEW - Control panel with OP 7: NEW - Wiring: NEW - New frequency converter for variable speed - Paintwork: according to customer specifications - With safety devices according to current standard - overhauled, with warranty 12 months, with CE-marking, Operating and maintenance instructions in English The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
High-speed cutter with 72cm cutting width Hydraulic pressure infinitely adjustable Electrical connection 400V/50Hz
used
Standard high-speed cutter with 82cm cutting width Hydraulic pressure infinitely adjustable incl. 2 knives Electrical connection 400V/50Hz
used
Quick cutting machine with 76cm cutting width Insert height 11cm Inlay depth 76cm Hydraulic pressure infinitely adjustable, 150daN-2500daN Program control, direct dimension input Electrical connection 400V/50Hz
used
We offer, used: Polyketting Conveyor belts - transport tracks with frequency-controlled / frequency converters on the motors for Tetra Pak beverage cartons 19 frequency-controlled motors More than 100 meters of transport track Subject to prior sale
used
specifications: - Air output: 6,000 m³/h - Pressing PA max: 500 Pa - Diameter pressure connection: 350 mm - Filter area: approx. 3.25 m² - Working surface (W x H): 2,080 x 1,930 mm - Area baffle: 1,800 x 1,800 mm - Dimensions of adjustable baffle plates (li + re): each 1,800 x 440 mm Engine data: - Power: 1.8 kW - Voltage: 380 V (star-delta) - Current: 3.8 A - Frequency: 50 Hz - Speed: 1,415 rpm - Transport dimensions (H x W x D): 2,500 x 2,000 x 800 mm (with pallet and mounted baffle plate and nozzles) - Weight: approx. 300 kg - Number of packaging units: 1 piece (on disposable pallet) The extraction wall was completely refurbished in our house and the fan was checked for its correct function. The extraction wall was completely cleaned and provided with new filter mats. Hint: Pipe components required for on-site operation can be requested from us. (Cha ...
used
Key data: 7 , 8
POWER SYSTEM compressed air unit consisting of: Screw compressor POWER SYSTEM model PS 7,5: - motor power KW 7,5 / HP 10 , volt 380 - air outlet pressure 8 bar - year 1995 , to EC regulations ATS air dryer model DSI60: - air flow 900 lt/min - refrigerant R.134a - year 2017, to CE regulations Vertical air tank: - capacity 470 liters, 11 bar - year 1995 , to EC regulations
new
Single-shaft shredder, 30 KW drive power, 800 mm working width, incl. discharge screw, Total height 2,000 mm, total width 1,800 mm, total length 2,850 mm Insertion opening 1,100 x 1,500 mm, perforated sieve 30 mm
used
1 POLYTEX pinking machine type ZO-30, cutting width 300 mm, machine supplied with 2 cutting knives: 1 new serrated knife with 4 mm serration gauge, 1 flat straight knife table size 605 mm x 315 mm, manual actuation
1 POLYTEX pinking machine type ZP (Zigzag cutting), knife width 1020 mm, stroke up to 65 mm height, up to 50 cuts per minute, machine equipped with precise hand lever feed mechanism, serrated knife with 5 mm gauge serrations, with FASNACHT security light guards, with laser cut indicator, motor power 2,2 kW, 3 x 380 V, 50 Hz, machine in immaculate condition as you can observe in the attached pictures.
used
M. No.: 5551360 Format (cm): 55 Equipment / Additional information: 1xreserve knife
used
Refer to code 1009 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.