plate shear used for sale

Sapphire 120L high shear mixing tank Stainless, high shear mixing vessel, variable speed mixer, pressure vessel, jacketed with adjustable temp settings, bottom mounted high shear, central bottom discharge, mobile, 1Ph

The JMC 407 is the top seller among our alligator claws. It is cost-effective, has sufficient knife length and enough power for most metal recycling tasks. It is suitable for cutting many materials, such as profiles, piping, motors, gearbox housings. The scissors are also often used for cleaning scrap metals or cutting vehicle radiators. The machine is equipped with a control system without electronics and a manually adjustable hold-down device, which also acts as a protective cover. By means of a foot pedal, the scissors can be used in single or continuous operation. The opening width can be adjusted by means of simple clamping screws. The scissors are from our demonstration pool and can be viewed or tested.

Machine Type: Guillotine Shears Manufacturer: RAS Model: 54.30 Year of construction: 1975 Condition: very good Offer Type: Used Machine Specifications: Capacity: 1040 x 4.0 mm Drive type: el./mech. Propulsion: 7.3 kW Remark: rip fence, Material supports and stop at the front, 2 spare blades Weight: 2000 kg The machine is in a very good condition and ready for immediate use and can be viewed and demonstrated by us. We would be pleased if you are interested in our offer. Errors, modifications and prior sale excepted.

Working length: 3,050 mm Cutting capacity: 6 mm steel 4 mm stainless steel Backgauge range: 1,000 mm Cutting angle adjustment: 0.5 - 2.5 degrees Equipped with: - 4x sheet metal support arms - Foot pedal - Sheet metal holding device at the back - Safety light curtain at the back Country of origin: Italy Motor power: 7.5 kW Machine LxWxH: 3,500 x 2,200 x 1,700 mm Machine weight: 6.600 kg

Working length: 3,100 mm Cutting capacity: 6 mm Backgauge range: 1,000 mm Equipped with: - Sheet metal holding device at the back - 3 sheet metal support arms - Foot pedal Country of origin: France Motor power: 7.5 kW Machine LxWxH: 3,800 x 2,100 x 1,860 mm Machine weight: 6.000 kg

Key data: 1040 mm, 4 mm

Max. cutting length: 1040 mm Max. sheet thickness: 4 mm steel Manual backgauge up to 550 mm Side stop and table extensions The rear area is secured by a safety fence with light barriers Knife sharpened Instruction manual available Weight: 1600 kg

: gebraucht : 2022 : 9636 : prompt, Zwischenverkauf v : Spanien : 13200 € : 1 : 55 to : 250 mm : 5 : 40/10 mm : 20 mm : 37 1/min : 300x15 mm : 120x10 mm : 40 mm : 10 mm : 5 kW : 1670 mm : 1160 mm : 2090 mm : 1390 kg DEMO MACHINE - MINT CONDITION 2 foot pedal for independent working on 2 stations flatsteel station anglesteel station round- and square steel station rectangular notching station punching station table on flat steel station table on punching station table on notching station complete with hydraulic oil user manual in GERMAN and ENGLISH OPTION: Kit € 930,00 length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

General SKU260U499 LocationBarneveld MakeYstral gmbh TypeC45000S/CONTI TDS-4 No.200431001 Year of construction2001 Main Features MaterialStainless steel Motor45 KW Rotor165 mm Specified Features - Inline mixer Continuous reactorcheck Rotor sizesDia: 165x60mm InletDN80 OutletDN80 Number of stages:1 With mechanical sealcheck Motor45kW, 415Volt, 2940rpm Rotor speed2940rpm MaterialStainless steel 1.4306 (304L) Information Mounted on framecheck Total height0,8m Weight560kg Floorspace1,6x1mInline high shear mixersYstralMixers > Inline high shear mixersBrand > Ystral What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

Key data: 3000 mm, 8 mm

Max. cutting length: 3,000 mm Max. sheet thickness: 8 mm steel Motorized backgauge with fine adjustment via handwheel up to 1000 mm Cutting length limitation Knife sharpened Weight: 6,800 kg

Key data: 2500 mm, 1 mm

Max. cutting length: 2500 mm Max. sheet thickness: 1.75 mm steel Manual backgauge up to 500 mm Side stop and table extension Knife sharpened

Silverson GX10 1500 High shear mixer Stainless, high shear mixer, shaft length 1150mm, head diameter 170mm, 3Ph

: neu : ca. 10 Wochen ab Auftrags : Spanien : 21200 € : 434.6 € : 1 : 60 to : 250 mm : 5 : 40 x 11 mm : 32 1/min : 350 x 15 mm : 120 x 10 mm : 45 / 40 mm : 10 mm : max. 150x10 mm : 5.5 kW : 1850 mm : 1300 mm : 2100 mm : 1390 kg with bending station 5 working stations flat steel shear with device to reduce deformation angle iron shear with round- and squarebars opening triangle notcher punching station press brake device for flat steel table at flat steel station table at notching station length stop 1000 mm with contact switch, for angle, flat or bar station hydraulic drive 2 foot release user manual in GERMAN and ENGLISH WE HAVE MORE THAN 700 REFERENCES! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pruning shears made by Reppel type TU 20-6 = - Weight: approx. 4.0 to -Sheet width/ sheet thickness 6mm

Used hydraulic cnc press brake Brand: HACO Model: ERM 60225 Year: 2000 Serial No.: 80983 Characteristics: Numerical control NEW: Cybelec Cybtouch 8 3 axes (Y1, Y2, X) Force: 225tn Bending length: 6,000mm Distance between uprights: 5050mm Neckline: 300mm Opening: 450mm Fast lowering speed: 80mm/s Motor: 18,7KW Weight: 29.500kg Includes 60mm cradle at 6 meters. Standard 88º punch at 6 meters.

- Rotor shears type MEWA UC 201 - Electric drive 2 x 75 kW - Rotor length: approx. 2 meters - Width of the blades: 70 mm - Weight approx. 50 tons - Incl. chain belt conveyor for discharging the product

Key data: 3020 mm, 6 mm, 750 mm

Combined CNC – controlled press brake / sheet metal shears Super compact machine with a very small footprint. Maximum cutting length 3,020 mm Nominal cutting capacity 6 mm sheet steel/ST 40 Cutting angle 1°30" 17 pieces of sheet metal hold-down, Ø hold-down plate 50 mm NC – controlled back gauge for guillotine shear station - adjustment range 750 mm Table height 750 mm. Maximum bending length between the side stands: 3,440 mm (column passage 3,550 mm) Maximum pressing force 1,000 kN Working height bending only 1,230 mm Lifting range bending station 170 mm Maximum installation height of the bending station is 250 mm (press beam surface in the lowest position), the backgauge adjustment range for the bending station is 750 mm. Dimensions including operating pendulum 4.25 m x 1.82 m x H 2.8 m Footprint 3.85 x 1.82 m Drive power 10 kW Weight 9,000 kg Equipment: ...

Combined CNC – controlled press brake / sheet metal shears Super compact machine with a very small footprint. Maximum cutting length 3,020 mm Nominal cutting capacity 6 mm sheet steel/ST 40 Cutting angle 1°30" 17 pieces of sheet metal hold-down, Ø hold-down plate 50 mm NC – controlled back gauge for guillotine shear station - adjustment range 750 mm Table height 750 mm. Maximum bending length between the side stands: 3,440 mm (column passage 3,550 mm) Maximum pressing force 1,000 kN Working height bending only 1,230 mm Lifting range bending station 170 mm Maximum installation height of the bending station is 250 mm (press beam surface in the lowest position), the backgauge adjustment range for the bending station is 750 mm. Dimensions including operating pendulum 4.25 m x 1.82 m x H 2.8 m Footprint 3.85 x 1.82 m Drive power 10 kW Weight 9,000 kg Equipment: ...

Article number: 01-05-001 Manufacturer: Eckold Very good general condition Machine workshop-tested Shipping time: All rights reserved. Year of construction: ca.1995 L x W x H: approx. 1200x800x1800mm Weight: approx. 400kg Accessories  Hydraulic power unit Other accessories on request Price and other technical data on request

Offer 24162 Specifications: - max. working width 3050 mm - max. cutting capacity - at 400 N/m² strength 6 mm - at 700 N/m² strength 4 mm - Adjustable cutting angle - Cutting gap adjustment via hand lever - Number of hydraulic hold-downs 14 pcs - Back gauge with positioning control AMADA 10 - 1000 mm - Front angle stop + support arm - Stroke rate 12 - 32 per/min - Drive 400 V / 12 kW - Table height approx. 800 mm - Space requirements incl. back gauge, without front support arms -ca. W 3800 x H 1950 x D 3200 mm - Transport width approx. 2200 mm - Weight approx. 6000 kg - With: - E - foot switch - Sheet metal holding -Mot. Material Conveyor Belt - Cutting length adjustment - Cutting line illumination

LVD HSL 3100 x 6 mm Cutting length: 3100 mm Max sheet thickness st 45: 6 mm Backgauge: 750 mm Adjustable cuttingedge: 0.5 > 3 mm Electric motor (power): 7,5 kW Length: 3500 mm Depth: 2200 mm Height: 2250 mm Weight: 5 ton

Key data: 3050 mm, 12 mm, 1000 mm

Working length 3050 mm, sheet thickness at 400N/mm² up to 12 mm Cutting angle adjustable up to max 2.5 ° 16 Hold-down device Stroke rate 35 - 10 1/min Weight approx. 8500 kg Incl. NC backgauge and automatic adjustment of Cutting angle and cutting gap Footswitch, Manual Hydraulically operated machines are dispensed without oil filling!

used scrap shears Lindemann LU800/8 PA60 with 4x 90 kW main drives, shear force 800t, shear width 800 mm, press box length 6 m, ready for operation

An Arnold rail crusher is offered from the site, consisting of: - Rail breaker with hydraulic system - Feed roller conveyor - Sling device with separating device - Swivel discharge conveyor - Control room The system is operational and still in use.

Working width: 2040 mm Sheet thickness: approx. 1 mm Back gauge: 600 mm Dimensions: 2400 x 1070 x 1100 mm Weight: approx. 900 kg

Working width: 2040 mm Sheet thickness: approx. 1 mm Back gauge: 600 mm Dimensions: 2400 x 1070 x 1100 mm Weight: approx. 900 kg

This Durma MS 2504 shearing machine, from 2006, is tailored for efficient shearing with a maximum cutting thickness of 4mm and a cutting length of 2550mm. The machine dimensions stand at 3100 × 1700 × 1350 mm and it weighs 3230 kg, ensuring sturdy operation during extensive usage. Designed primarily for sheet metal applications, it remains operational and under power, ready to handle a diverse range of shearing tasks. For more information about this Durma shearing machine, please reach out to us.

LASER PRIMA INDUSTRIE Mod. 2D/3D DOMINO Year 2006 1500x3000 2.5 kw 22,000 working hours Visible in operation No loading and unloading

Max. sheet thickness: 2 mm steel Max. blank diameter: 750 mm Motorized drive via foot switch

hydraulic guillotine shears, manufacturer: EHT, type: TSS 4-60, year of manufacture: 2003, serial no.: 108211, cutting length: 6,075 mm, cutting thickness: 4 mm, various trestles approx. 6 pieces

: neu : 2024 : 9731 : Juni 2024, Zwischenverkau : Türkei : 30100 € : 611.03 € : 1 : 3100 mm : 4 mm : 42 1/min : 750 mm : 7.5 kW : 2 Stk. : 800 mm : 450 mm : 3700 mm : 2300 mm : 1350 mm : 3730 kg mot. back gauge with digitalreadout DT 5 hold down with rubber pads side lay with T-sluts 2 supporting arms ball in the table tape measure tilt stop light barriers on the back of the machine cutting line illumination user manual in GERMAN and ENGLISH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Sheet thickness: 6,00 mm Sheet width: 2050 mm Depth rear gauge: 2050 mm GuillotineHACO - TSX 2006 MACH-ID 8599 Robosoift SC5 Backgauge Sheet arms front side Straight infeed arm front side ( left)  Fully hydraulic opperated Maximum sheet thickness:        6mm Max. cutting length:            2050mm Strokes on full length:         10mm Strokes in short 1000 length:   15 Cutting angle:                  0,5 - 3° Length backgauge:               2050mm Number of down holders:         13 Operated mechanical or hydraulic:Hydraulic Power:                          7,5kW Length:           ...

Sheet thickness: 4,00 mm Sheet width: 1100 mm Depth rear gauge: 550 mm GuillotineIndumasch - 410 MACH-ID 7773 Make: Indumasch Type: 410 Year: 1988 Arc depth 550 mm Capacity steel 5 mm Capacity stainless 3 mm Minimum circel diameter 170 mm Maximum sheet thickness:        4mm Working speed:                  35000mm/min. Operated mechanical or hydraulic:Hydraulic Power:                          4kW Length:                         2850mm Width:                          1200mm Height:                         1600mm Weight:          ...

General SKU200W001 LocationBarneveld MakeHPV TypeDish LPD liquid processing unit No.1200-0708/2008 Year of construction2008 Main Features MaterialStainless steel Motor5.5 KW Specified Features - Inline mixer Capacity18,0 t/h of final product MaterialStainless steel 1.4435 (316L) Information Total height2,6 m Weight3500 kg CEcheck Floorspace6,4x2,35 m Extra Specificationsperfume, aroma, mixing skid The LLPD mixing machine is designed for continuous mixing of the final product and its accumulation for subsequent pumping into final packaging. The machine is capable of producing various modifications of the final product (FP) in 10 perfume variants and different color spectra available within the capacity ranges of dye dosing systems. Qualified reblend (RB) can be added to FP during normal production within the dosing capacity range. The LLPD mixing machine consists of: � ...

Hydraulic guillotine for cutting sheet metal by Safan the Netherlands, type VS 255-10, 310 mm x 10 mm (ST40). The machine has a quickly changing knife gap with thickness reading, and a hydraulically variable knife angle of 0.5 -3 degrees. 15 kW motor. Machine weight 10 tons. NC electric bumper with position transmitter with readout, bumper travel 1250 mm. Electrically adjustable cutting length in the range of 30-3100 mm. 2 x supports for holding sheets of metal at the front of the machine, plus a 1500 mm ruler for cutting at an angle of 90 degrees. Light line enabling line cutting. The knives are sharp, the machine cuts copier paper. Original DTR documentation.

Key data: 2500 mm, 6 mm, 1000 mm

Type 509, with pneumatic sheet metal holding Adjustable cutting length, cutting angle and cutting gap 5 table extensions / angle stops approx. 6000 kg

Shear Amada GS 840 4100x8mm with thin sheet metal stand Brand: AMADA Model: GS-840 S/N: C 99 07 16 Year: 1999 Power: 15KW Weight: 11650kg Hydraulic vertical shear with variable angle. Control: AMADA PROMECAM Cutting capacity: 8mm carbon steel / 6mm inox Cutting length: 4050mm Degrees adjustment: 0,4º - 2,1º Cursa: 190mm Treaders: 21 Back stop: 1000mm Front table base: 700m Dimensions: 2040x4810x2210(h)mm Optional included: - Pneumatic support for thin sheet metal.

Guillotine shears, manufacturer: HESSE, type: MS 3004, year of manufacture: 2010, serial no.: 313510563, max. machining capacity: 3,100x4 mm

: gebraucht : 2004 : 9726 : ca. 2 Wochen ab Auftragse : Türkei : 6750 € : 1350 mm : 3 mm : 35 1/min : 1,5 ° : 550 mm : 3 kW : 2 Stk. : 850 mm : 400 mm : 1700 mm : 1350 mm : 1200 mm : 950 kg manualback gauge automatic sheet hold down hold down with rubber pads moveable foot switch side support arm 2 supporting arms user manual in GERMAN does not complie with the German UVV and Austrian AMVO The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: - Max. working width 3040 mm - max. material thickness 4 mm - Manual cutting angle adjustment - Stroke rate up to 34 1/min - Backgauge with positioning control Pos100 - Table height approx. 850 mm - Front angle stop - 2 front support arms - Rear space protection with light barrier - E-foot switch - Pneumatic connection 6 bar - Drive 400 V - Space requirement without support arms approx. W 4000 x H 1400 x D 2100 mm - Weight approx. 4700 kg

Machine parameters: Max. cutting length: 3150 mm Max. sheet thickness: 6 mm Machine weight: 6800 kg The machine is in perfect condition after GO, the following was done: grinding of blunt knives, resealing of working cylinders and their flanges, resealing of holders and sections, replacement of polyurethanes, replenishment of nitrogen, electrical repair. (Current invoice proving the scope of work of course)

Key data: 4050 mm, 6 mm, 1000 mm

Min./Max. Cutting Angle = 0.5 - 2° Cutting gap control = 0.05 - 0.8 mm Stroke rate = 10 - 45 Adjustable back gauge = 750 - 1000 mm Sheet metal high bracket Oil tank = 150 L Motor power = 7.5 kW, 400 V Machine weight = approx. 10,000 kg

CAPASITY 60 T

Specifications: - Max. cutting width 3050 mm - Max. cutting capacity at 45 Kp/mm² 6 mm - Cutting angle adjustment 1 - 2.20 ° - Cutting gap - adjustment via lateral adjustment lever - Number of hold-downs 16 pcs - Stroke rate up to 22 /min - Front angle stop 1100 mm - 2 front support arms 600 mm -Mot. Backgauge with ELGO positioning control - 5 - 1000 mm - Cut line illumination - E – Footswitch - Drive 400 V / 12 kW - Space requirement approx. W 4100 x H 1500 x D 2200 mm - Weight approx. 5.0 t

Working length: 3040 mm Max. thickness of sheet metal to be cut: - 400 MPa steel: 1,0 mm - Al 250 MPa: 1,5 mm The shears are characterized by a solid, rigid construction and high reliability. The cutting edges of the shears are made of high quality tool steel and are hardened. The main part of the shears is the welded stand, in which the guide surface for the ram is machined. The vertical movement of the ram is derived from the eccentric shaft by means of a connecting rod and pin. The shearing force is exerted by a hand lever pressed onto the end of the eccentric shaft. The shears require almost no maintenance, only occasional lubrication of the sliding points with a lubricating press and sharpening of the blades after they have become dull. The knives on the shears can be sharpened repeatedly. L x W x H: 3465 x 770 x 1160 mm Weight: 830 kg By prior arrangement, possibility of in ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 27200 € : 552.16 € : 2050 mm : 4 mm : 42 1/min : 750 mm : 7.5 kW : 800 mm : 450 mm : 2700 mm : 2300 mm : 1350 mm : 2800 kg motorizedback gauge atrecirculating ballscrew with Control DT5 hold down with rubber pads Side Lay with T-Slot 2 Sheet support arms ball in the table tape measure tilting stop light barriers on the back of the machine cutting line illumination user manual in GERMAN and ENGLISH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate width: 2,050 mm, weight approx.: 1,000 kg, Approx. Onsite Dimension. (l x w x h): 2,300 x 750 x 1,600 mm

Description: PUNCHING Punching force: 60 ton Punching capacity: Ø22 x 20 mm (Diameter x Thickness): Ø40 x 11 mm Throat depth: 200 mm Maximum stroke length: 40 mm Cycles / Min. (15 mm stroke): 34 mm Working height up to mould: 1050 mm  , ANGULAR CUTTING Cutting force: 60 ton With 90° cut: 100 x 100 x 8 mm Working height: 1070 mm  , FLAT SHEAR Flat bar shear: 350 x 15 mm Blade length: 360 mm Working height: 805 mm  , BAR SHEAR Shear for round bars: ø40 mm Shear for square bars: 38 x 38 mm Cutting channels: 102 mm optional tool I-beam cutting: 102 mm optional tool NOTCHING Rectangular notching (W x D x T): 50.8 x 90 x 8 mm V-cut (L x W x T): 90 x 90 x 8 mm optional tool Working height: 1050 mm  , SPECIAL TOOLS optional  , Single Vee press brake (W x T): 160 x 8 mm tool optional Multi Vee press brake (W x T): 250 x 6 mm tool optional ...

Guillotine shears - hydraulic Make Atlantic Type ATS 3012 Year of construction 1990 Sheet width 3050 mm Sheet thickness 12 mm Distance between columns 3100 mm Table height above floor 900 mm Cutting angle adjustment 0.5 - 3 ° Number of strokes 6 - 13 strokes/min Back gauge - adjustable 1000 mm Hold-down device 18 pcs Oil capacity 350 l Total power requirement 22.5 kW Machine weight approx. 8 t Machine dimensions L x W x H 3.96 x 2.10 x 2.22 m accessories electr. backgauge, spare blade

Offer 24176 Specifications: - max. working width 3050 mm - max. cutting capacity St 40 6.5 mm - Cutting angle hydr. adjustable 0.3 - 3 ° - Cutting gap adjustment by hand - Number of hydraulic hold-downs 18 pcs - Motor - Back gauge 20 - 1000 mm - Front angle stop + support arms - Stroke rate depending on cutting angle and cutting length 7 - 17 rpm - Hydraulic drive 400 V / 11 kW - Table height approx. 800 mm - Space required including back gauge, without front support arms ca. W 4000 x H 1700 x D 2250 mm - Weight approx. 4800 kg - with: - E-foot switch - Cutting line illumination - - Cutting length preselection via potentiometer

Offer 24246 Specifications: - Max. working width 2550 mm - Max. material thickness steel 400 N/mm² 4.0 mm - Max. material thickness stainless steel 700 N/mm² 2.5 mm - Cutting angle 1.8 ° -Mot. Controlled positioning of the back gauge up to 750 mm - Front angle stop - 2 pieces support arms - electr. Footswitch - Rear space protection with light barrier - Drive 400 V / 7.5 kW - Space requirement approx. W 3300 x H 1300 x D 2300 mm - Weight approx. 3500 kg