135,425 used machines on RESALE, but how to find them? Machine Search
Quick coupler, Without spoons, size 2230x800x350mm. Auction-ID: A1-50447-128
FIAT TRATTORI 1380 DT | 135 hp | H-Kennzeichen | Restored Powerful all-wheel drive classic car with BAAS front loader, extensive restoration and valid technical inspection until 12/2026. Highlights ✔ 99 kW (135 hp) / 5,461 cc 6-cylinder turbodiesel ✔ Year of manufacture 1981 | H license plate ✔ Technical inspection until 12/2026 without recognizable defects ✔ BAAS Prima 380 F/40 Front Loader with Joystick ✔ Air Brake System (WABCO) ✔ 2 double-acting hydraulic control units (4 connections) ✔ Front and rear wheel weights ✔ 2 additional tanks of approx. 60 litres each ✔ Mitas tyres 420/85 R28 front & 520/85 R38 rear Restoration / Investments ✔ Completely primed and repainted ✔ Cabin fully restored inside ✔ Electrics partially renewed ✔ Front axle revised ✔ Right lifting cylinder renewed ✔ New battery (approx. 3 ...
Specifications: Working length: 3050 mm Max. bending power: 30.0 mm Max. bending capacity length 1500 mm: 42 mm Bend: 25.0 mm Diameter upper roller: 460 mm Diameter lower roller: 460 mm Number of driven rollers: 3 hydraulic snap roller bearing Engine power: 37 kW Dimensions (length x width x height): approx. 5850 x 2550 x 2650 mm Weight: approx. 30 tons Note: Compact design, therefore low space requirement Parts of the hydraulics installed under the machine
Specifications: Working length: 2550 mm Max. bending power: 6.0 mm Bend : 4.0 mm Diameter upper roller: 176 mm Diameter lower roller: 176 mm Control panel with digital display Motor power: 7.5 kW CE mark Dimensions (length x width x height): approx. 4000 x 1400 x 1500 mm Weight: approx. 3.6 tons Note: the machine was used exclusively for straightening coated aluminum sheets Rollers were wrapped in foil, which was removed without leaving any residue Condition of the rollers almost as good as new few operating hours
Specifications: Working width: 1050 mm Max. bending power: 100.0 mm Max. bend: 80.0 mm Diameter upper roller: 530 mm Diameter of side rollers: 530 mm Conical bending device by inclined position of the two side rollers Mobile control panel with digital display Engine power: 37 kW Hydraulic Safety Chucks CE mark Net weight: approx. 16 tons Auxiliary: 2. Roller set : Diameter upper roller: 360 mm Diameter of side rollers: 360 mm
Baking Plates for PRO 1 Baking Machine - Condition: used - Engraving (Lower Baking Plate): approx. 5 x 5 mm - Engraving Depth (Lower Baking Plate): approx. 1,45 mm - Wafer Sheet Thickness: approx. 3 mm - Connecting Shaft: approx. Ø 16 mm - Collar radius: approx. 96,5 mm
size of pallet:400x400 mm numbers of pallets:15 table load:400 kg weight of the machine ca.:0,060 t dimensions of the machine ca.:0,4 x 0,4 m 15 pallets for Makino A 55, size 400 x 400 with T-slots for sale
Hot plate press (electric) Brand: ORMA Type: NPC 6/120 new machine Technical data: Heating plates: 3500x1300mm Cylinder: 6 pieces Press force: 120t Stroke/opening dimension: 450mm Connection value: 28.8kW (ELKOM plates) Options: - Intermediate plate - Anodized surface for ELKOM panels - Parallelism sensor á 1,000.00 EUR - Pressing mechanism from above (fixed lower plate) - Max. temperature till 150°C - Max. temperature till 200°C - 4-sided loading possible - Mylar protective film - Fiberglass Teflon protection - Hardware for Industry 4.0
TECHNICAL SPECIFICATION:. - Fixed table length:12000 mm - . width:3000 mm - . height:350 mm - number of T-slots:10 - distance between T-slots:300 mm Technical description : FLOOR PLATES consisting of 4 (four pieces) at segments of 6000mm length and 1500mm width
length:1000 mm width:800 mm weight of the machine ca.:0,7 t dimensions of the machine ca.:1,0 x 0,8 x 1,4 m Hardstone measuring plate complete with FISCHER tailstocks and 4 leveling elements.
length:1600 mm width:1000 mm plate height:200 mm weight of the machine ca.:1 t dimensions of the machine ca.:1,6 x 1,0 x 1,3 m Hardstone measuring plate with support desk and 2 tailstocks
- Filter surface area: 3m2 - Evacuation: manual Equipment : - Control window with inlet and outlet lighting - Circulation pump - Adjustable dosing pump - Agitator - Connection: butterfly valves, Friedrich n°2 40 Dimensions : - Length: 1750 mm - Width: 700 mm - Height: 1000 mm - In working order
diameter:400 mm total power requirement:110 V, 125 W weight of the machine ca.:72 kg
sheet width:3050 mm plate thickness:4 mm total power requirement:9 kW weight of the machine ca.:6 t dimensions of the machine ca.:3900 x H 1850 x T 2100 mm
stone measuring plate 400 x 400 x 50 mm ( 3 pieces available / price per piece )
length:600 mm width:500 mm weight of the machine ca.:0,05 t dimensions of the machine ca.:1,5 x 1 x 0,8 m Texte, Bilder, Grafiken, Layout, Strukturen und Algorithmen etc. unterliegen weltweitem Urheberrecht. Unerlaubte Verwendung der Daten, werden sowohl strafrechtlich als auch zivilrechtlich verfolgt. Das ausschließliche Urheber- / Nutzungsrecht dieser Daten wurde nachfolgender Person eingeräumt. Copyright © 2005-2024, Josef Weber. All rights reserved.
floor-plate length:6000 mm floor-plate width:2000 mm floor-plate height:460 mm weight of the machine ca.:12,5 t dimensions of the machine ca.:6 x 2 x 0,46 m
Vacuum lifter, vacuum lifter from Schmalz for heavy plates with new suction rubber Load capacity 150kg horizontally and vertically Vacuum cleaner can be swivelled 90 degrees motorised Suction box 1000 x 675mm Acoustic warning signal in case of too low vacuum 400V, 1.5kW Can be attached to on-site chain hoist CE mark No test book available Vacuum cleaner rubber renewed Mint condition The machine can be demonstrated on site by appointment. We offer only machines that are ready for demonstration in our warehouse, see "other offers of this year". provider".
Fuji FLHZ 85 CD Quartz 3 Plate Developing Machine; very good condition; cleaned and tested; Inlet width 850mm; Chiller. Plate processor Fuji FLHZ 85 CD Quartz 3; very good condition; cleaned and checked; working width 850mm; Chiller.
floor-plate length:6000 mm floor-plate width:2000 mm floor-plate height:460 mm weight of the machine ca.:12,5 t dimensions of the machine ca.:6 x 2 x 0,46 m
table length:2000 mm table width:600 mm table height:300 mm mounting surface:700 x 600 mm centre distance:1200 mm centre height:160 mm Dimensions (WxDxH):2,0 x 0,6 x 0,3 m
- Number of sections: 1 - Capacity: 1000 l/h - Connection: Clamp 50.5 mm - In good condition
Ø 100, class 1.6 0 - 25 bar Version: Vertical Display range: 0 - 25 bar Scale graduation: 0.5 bar Materials: Housing 1.4571, measuring system and connection, viewing panel multi-layer safety glass Connection: 1/2'' bottom (AB) Plate spring pressure gauge
Used-refurbished machine Unger 160 mm cutting attachment 4500 kg/h max. capacity Technical data Mixing chamber volume: 400 L Capacity approx.: 4500 kg/h Power: 35 kW (grinder motor) Electrical fuse: 125 A Dimensions: 1500x1335x1810mm Weight: 1700 kg WAW G 160 model 2000 S with mixing arm, hydraulic loader for 200 l hopper, push button operation, mixing arm, hopper volume 400 l, mixing capacity approx. 260 kg, machine weight approx. 1700 kg, hole plate diameter 160 mm, max. capacity 4500 kg/h, brand new cutting set with sorting and separating device (bone removal accessory).
M. No.: 91080-41861 Age : around 1994 Speed: first 70 Sec. / Following 52 Sec. Format (cm): 41,4 x 55 (max.) Equipment / Additional information: Plate width (cm): 22.9 - 41.4 Plate length (cm): 22.0 - 55 Maximum effective image size (cm): 40.4 - 54 Magnification: 100% Lens (cm): 25 Step and Repeat setter: Original side down Digital recording: 0 - 99 Light source: 1 Halogen-Diode, 80 V / 800 W Tank capacity: Activator 0.55 l, stabilizer 0.60 l Power supply: 200 V / 220 V / 240 V, 1.9 Kw High quality plate results: up to 133 lpi
Measuring and marking plateCast steel-grey cast iron heavily ribbedLength 1000 mmWidth 1000 mmThickness 54/225 mmWorking height approx. 800 mm- 4 pieces feet with adjustment screws for aligning the plateWeight 390 kggood surface; used
4 pieces of adjustable jaws INGERSOLL for face plateChuck jaws for lathe chuck, mechanical clamping device, clamping blockNo: 39.02.10000 / 501.397Jaw width 70 mmJaw length 180 mmJaw carrier height 150 mmBase plate 325 x 265 mm- Step jaws for turning as rotary and drilling jaws- Jaw adjustment via trapezoidal threaded spindle- Jaw support with 6 recesses 40 x 30 mm for fastening- Distance between recesses 280 x 133 and 220 x 90 mm (center)Dimensions L x W x H 325 x 265 x 215 mmWeight per jaw 36.5
spindle diameter: 130 mm x-travel: 3000 mm y-travel: 2000 mm total power requirement: 4,5 kW weight of the machine ca.: 30 t Spindle Ø 130 mm Spindle taper SK 50 Working range: X = column, longitudinal 3,000 mm Y = headstock, vertical 2,000 mm Z = spindle stroke 1,000 mm Lower table 3,300 x 2.400 mm Max. weight on table 10 tons/m² Min./ max position of work spindle above table 770 / 2,770 mm Feeds 0.9 - 2,000 mm/min Quick feed for headstock and column 5,000 mm/min Quill feed 0.5 - 1,200 mm/min Speed range, partially infinitely variable 4.5 - 1,250 rpm Weight, approx. 30,000 kg Accessories / Special Features HEIDENHAIN Digital Display for 3 axes. Hardened guideways. Ball screw spindles. Infinitely variable spindle speeds and feeds. Feeds can be individually driven with motor. Moving operating platform. Hanging control panel. Manual operati ...
length: 125 mm width: 100 mm height: 70 mm : - mm weight of the machine ca.: 0,5 Kg dimensions of the machine ca.: 0,15 x 0,15 x 0,07 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Lifting capacity: 2000 Kg Magnetic field: 350 x 150 mm weight: 70 Kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2000 mm plate thickness: 8 mm pre-bending: total power requirement: 7,5 kW weight of the machine ca.: 3,6 t dimensions of the machine ca.: 3600x1250x1350 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
HORIZONTAL PLATE FREEZER CABINET, TUCAL MODEL: A.H. + COOLING COMPRESSOR IN NOISELESS CABINET, MODEL: UC Technical description: Serial number: 609 Power supply: 400 V, 3 Ph, 50 Hz Pressure: 7/10 bar Temperature: -35 / +35 °C Refrigerant: NH3 Dimensions: 3000 x 1300 x 2300 mm Cooling compressor in noiseless cabinet, model: UC Serial number: 304 Year: 10/2015 Bitzer cooling compressor, type: OSNA8571-k Serial number: 1088702179 Dimensions of noiseless cabinet: 3000 x 1500 x 2320 mm
used
Cutting lenght 6000 mm Cutting thickness 13 mm
Pressure plate punch Beil 780/425-S-H-AP2; cleaned and tested; die-cut 780 and 425 mm autoplate; Investment Contact. Plate punch hatchet 780/425-S-H-AP2; cleaned and checked; punch size 780 and 425mm Autoplate; contact for plate.
Key data: 1470 mm, 1400 mm, 750 mm
2 Cast iron V supports Width: 1400 mm Height: 1370 mm Base depth: 750 mm Slot width: 200 mm V width: 940 mm V depth: 430 mm Total height under sole: 1470 mm Weight: 2,3 T / unit
sheet width: 2100 mm plate thickness: 2,0 mm distance between columns: 2150 mm roll diameter: 90 mm total power requirement: 1,5 KW weight of the machine ca.: 0,7 t dimensions of the machine ca.: 2,5 x 0,7 x 1,3 mm Sheet metal bending machine 3 rollers - 2 driven rollers - Foot switch - Emergency stop device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Copper plate for lapping machine. Dia 600mm, NEW, make: Melchiorre, Mimu Machine Tools Gussago BS Italy, Lapping is a machining process in which two surfaces are rubbed together with an abrasive between them, by hand movement or using a machine., This can take two forms. The first type of lapping (traditionally called grinding), involves rubbing a brittle material such as glass against a surface such as iron or glass itself (also known as the lap or grinding tool) with an abrasive such as aluminum oxide, jewellers rouge, opticians rouge, emery, silicon carbide, diamond, etc., between them. This produces microscopic conchoidal fractures as the abrasive rolls about between the two surfaces and removes material from both., The other form of lapping involves a softer material such as pitch or a ceramic for the lap, which is charged with the abrasive. The lap is then used to cut a harder mate ...
Unloading plate for cherries 29-20,, Original Ferrum plate,, 50 holes,, outer diameter: 29 mm,, inner diameter: 20 mm,, very good condition.
Halbautomatischer Stanztiegel / Automatic Platen Die Cutter ETERNA ML 930 GII Year 2008 - Serial-No. EP51568 Format 670 x 930mm Weight 2800kgs Included frame and tools, very good condition
• Manufacturer: AGI • Model: TOWER A3W • Year of construction: 2017 • Machine Type: Polymer Plate Processor • Machine type: Prepress machine for flexographic printing • Max. plate format: DIN A3 (297 mm x 420 mm) • Application: Development and processing of photopolymer plates • Application: Label printing, packaging, flexographic printing • Compact design, ideal for small to medium-sized printers • Condition: Very well maintained, ready to use
maximum number of results exceeded
please refine your search
50 € 
